12 24 00-1

SECTION 12 24 00 WINDOW SHADES

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Manually operated, roll-up fabric interior window shades including mounting and operating hardware.

B. Motorized, roll-up fabric interior window shades including motor operator, controls, and mounting hardware.

1.2 RELATED SECTIONS

A. Section 06 10 00 - Rough Carpentry.

B. Section 07 90 00 - Joint Protection.

C. Section 09 21 16 - Gypsum Board Shaft Wall Assemblies.

D. Section 09 51 23 - Acoustical Tile Ceilings.

E. Division 16 - Electrical: Electrical supply, conduit, and wiring for motorized window shades.

1.3 REFERENCES

A. NFPA 70 - National Electrical Code.

B. NFPA 701-99 - Fire Tests for Flame-Resistant Textiles and Films.

C. GREENGUARD Environmental Institute Children & Schools.

1.4 SUBMITTALS

A. Submit under provisions of Section 01 33 26 - Source Quality Control Reporting:

B. Product Data: Manufacturer's data sheets on each product specified, including: 1. Preparation instructions and recommendations. 2. Installation and maintenance instructions. 3. Styles, material descriptions, dimensions of individual components, profiles, features,

finishes and operating instructions. 4. Storage and handling requirements and recommendations. 5. Mounting details and installation methods. 6. Typical wiring diagrams including integration of motor controllers with building

management system, audiovisual and lighting control systems as applicable.

C. Shop Drawings: Plans, elevations, sections, product details, installation details, operational clearances, wiring diagrams and relationship to adjacent work.

D. Window Treatment Schedule: For all roller shades. Use same room designations as indicated on the Drawings, field verified window dimensions, quantities, type of shade, controls, fabric, and color, and include opening sizes and key to typical mounting details.

12 24 00-2

E. Selection Samples: For each finish product specified, two complete sets of shade cloth options and aluminum finish color samples representing manufacturer's full range of available colors and patterns.

F. Verification Samples: For each finish product specified, two complete sets of shade components, unassembled, demonstrating compliance with specified requirements. Shade fabric sample and aluminum finish sample as selected, representing actual product, color, and patterns. Mark face of material to indicate interior faces.

G. Maintenance Data: Methods for maintaining roller shades, precautions regarding cleaning materials and methods, instructions for operating hardware and controls.

H. Manufacturer's Certificates: Certify products meet or exceed specified requirements.

1.5 QUALITY ASSURANCE

A. Manufacturer Qualifications: Obtain roller shades through one source from a single manufacturer with a minimum of twenty years experience in manufacturing products comparable to those specified in this section.

B. NFPA Flame-Test: Passes NFPA 701. Materials tested shall be identical to products proposed for use.

1.6 DELIVERY, STORAGE, AND HANDLING

A. Do not deliver window shades until building is enclosed and construction within spaces where shades will be installed is substantially complete.

B. Deliver products in manufacturer's original, unopened, undamaged containers with labels intact.

C. Label containers and shades according to Window Shade Schedule.

D. Store products in manufacturer's unopened packaging until ready for installation.

1.7 SEQUENCING

A. Ensure that locating templates and other information required for installation of products of this section are furnished to affected trades in time to prevent interruption of construction progress.

B. Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.

1.8 PROJECT CONDITIONS

A. Install roller shades after finish work and ambient temperature, humidity and ventilation conditions are maintained at levels recommended for project upon completion.

1.9 WARRANTY

A. Hardware and Shade Fabric: Draper's standard twenty-five year limited warranty.

B. Motors and Controls: Draper's standard five year limited warranty.

PART 2 PRODUCTS

2.1 MANUFACTURERS

12 24 00-3

A. Acceptable Manufacturer: Draper, Inc., which is located at: 411 S. Pearl P. O. Box 425 ; Spiceland, IN 47385-0425; Toll Free Tel: 800-238-7999; Tel: 765-987-7999; Email:request info; Web:www.draperinc.com

B. Requests for substitutions will be considered in accordance with provisions of Section 01 60 00.

2.2 MANUALLY OPERATED WINDOW SHADES

A. Manually Operated Window Shades with Independent Control: Manually operated, vertical roll-up, fabric window shade with components necessary for complete installation; Manual FlexShade XD as manufactured by Draper, Inc. 1. Operation: Bead chain and clutch operating mechanism allowing shade to stop when

chain is released. Designed never to need adjustment or lubrication. Provide limit stops to prevent shade from being raised or lowered too far. a. Clutch mechanism: Fabricated from POM thermoplastic with welded 0.354 inch

(9 mm) primary steel post with rotational bearing, overrunning design, and positive mechanical engagement of drive mechanism to tube. White or Black color as selected by Architect. Center bead chain placement for right or left hand operation and accommodates side channel with no adjustment of chain location.

b. Bead chain loop: Stainless steel bead chain. c. Bead Chain Hold Down: P-Clip.

2. Rollers: Extruded aluminum roller tube of appropriate diameter to support shade fabric with minimal deflection. a. Minimum Roller Tube Diameter: 1.56 inches (40 mm). b. Fabric Connection to Roller Tube: Spline fabric/roller attachment system to

allow shade fabric to be removed from roller without having to remove roller from brackets.

c. Fabric Length: 6 inches (152 mm) greater than window height minimum. d. Bottom Slat: 13/16 inch (20.6 mm) aluminum dowel, encased in bottom hem

with heat sealed ends. e. Orientation: Regular from back of roller.

3. Mounting: a. Endcaps and headbox.

4. Endcaps: Stamped steel with universal design suitable for mounting to ceiling, wall, and jamb. Provide size compatible with roller size. a. Endcap covers: To match fascia or headbox color.

5. Headbox Ceiling/Wall style: Aluminum fabrication with removable closure, endcaps, and back and top cover piece:

2.3 MOTORIZED WINDOW SHADES

A. Type: Motorized vertical roll-up, fabric, window shade with motors, controls, mounting brackets, and other components necessary for complete installation; Motorized FlexShade as manufactured by Draper, Inc. 1. Endcaps and headbox.

B. Shade Motor and Control System 1. Radio Technology Motor- 110 VAC motor with built-in radio receiver. Tubular motor

concealed inside each shade roller tube. a. Individual Control, Group Control and Individual and Group Control:

1) Four channel wireless handheld transmitter-Black. 2) 16-Channel wireless handheld transmitter-White. 3) Four channel wireless wall switch for radio motor control-White.

C. Roller: Fabricated from extruded aluminum or steel. Diameter, wall thickness, and material

12 24 00-4

selected by manufacturer to accommodate shade size. Provide with roller idler assembly of molded nylon and zinc-plated steel pin. Sliding pin to allow easy installation and removal of roller. Fabric connected to the roller tube with LSE (low surface energy) double sided adhesive specifically developed to attach coated textiles to metal. Adhesive attachment to eliminate horizontal impressions in fabric.

D. Endcaps: Stamped steel with universal design suitable for mounting to ceiling, wall, and jamb. Provide size compatible with roller size.

E. Endcap covers to match fascia/headbox finish.

F. Coupling system: Couplings to join motorized shade rollers to allow operation by single motor. FlexShade Coupling System as manufactured by Draper, Inc. Provide endcaps to receive couplers and support multiple shades.

G. Shade slat: Slat encased in heat-seamed hem.

2.4 SKYLIGHT SHADES

A. Type: Electrically operated, horizontal, roll-up, fabric, skylight shade; Skylight FlexShade System as manufactured by Draper, Inc.

B. Method of installation: Mounted inside of skylight opening and extending from wall to wall

C. Shade Motor and Control System

1. Radio Technology Motor- 110 VAC motor with built-in radio receiver. Tubular motor concealed inside each shade roller tube. a. Individual Control, Group Control and Individual and Group Control:

1) Four channel wireless handheld transmitter-Black. 2) 16-Channel wireless handheld transmitter-White. 3) Four channel wireless wall switch for radio motor control-White.

D. Rollers:

1. Motorized roller: 2 inches 50 mm diameter extruded aluminum.

2. Take-up roller: 1-3/4 inches 44 mm diameter galvanized steel roller with heavy-duty spring. Equip with take-up reels to ensure take-up cable remains in alignment.

3. Provide with roller idler assembly of injection molded plastic containing a spring-loaded steel pin for easy installation and removal of roller.

E. Endcaps: Stamped steel with roller adapter and designed for mounting enclosure and receiving fabric guides.

F. Enclosures: Fabricated from 0.06 inch 1.59 mm thick extruded aluminum sections with endcaps and opacity plates.

1. Size: 3-1/2 inches 89 mm] high by 4 inches 102 mm wide by length required for shade being provided.

2. L-shaped removable front and top cover and L-shaped removable back and bottom.

G. Side Support Flanges: Consist of two sections. One section contains grooves for the fabric guide, and a groove for the glide strip. The second section contains the flange/endcap locators. Outside mounts require plastic cover buttons.

12 24 00-5

H. Flange/endcap locator: Type 6 injection molded nylon. (Aligns side support flange and endcap.)

I. Slat bar: Provides an attachment point for the shade fabric and for the cable idler bearings. The idler bearings provide self-adjusting equalization of the cable tension at each end of the slat bar.

J. Take-up cable: 3/64” stainless steel, nylon coated, with a minimum breaking strength of 220 lbs.100 kg; never visible during operation.

K. Fabric guide: Plated steel transition for fabric rolling into side support flange.

L. Fabric Support System: Horizontal steel stays are installed at regular intervals and covered. This system enables the shade to withstand reasonable air pressure differentials and gravity. Please note: extreme air currents or physical interference may cause product failure.

M. Opacity plates: Steel plates with rubber O rings installed on endcaps to eliminate light leakage.

N. Exposed aluminum finish: Clear anodized, Black, White, Ivory, Charcoal bronze baked enamel paint.

2.4 FABRIC

A. Light-Filtering Fabrics 1. SheerWeave Series SW2500 by Phifer: VOC Emissions: GREENGUARD Children &

Schools -certified as a low emitting fabric. Manufacturer to supply GREENGUARD Children & Schools certificate. 500 denier fiberglass, vinyl coated and woven into a 2 x 2 basket weave. Fire rating: NFPA 701. Bacteria and Fungal Resistance: ASTM G 21 and ASTM G 22. Series SW2500, 1 percent open, .024 inches thick.

2. SheerWeave Series SW2400 by Phifer: VOC Emissions: GREENGUARD Children & Schools -certified as a low emitting fabric. Manufacturer to supply GREENGUARD Children & Schools certificate. 500 denier fiberglass, vinyl coated and woven into a 2 x 2 basket weave. Fire rating: NFPA 701. Bacteria and Fungal Resistance: ASTM G 21 and ASTM G 22. Series SW2400, 3 percent open, .019 inches thick.

3. Series SW2701 SheerWeave: Duplex basketweave fabric-light exterior color combined with dark interior color for thermal comfort and view-through. GREENGUARD Children & Schools certified as a low emitting fabric. Manufacturer to supply GREENGUARD Children & Schools certificate. Fire rating: NFPA 701. SW2701-.1 percent open.

4. Series SW2703 SheerWeave: Duplex basketweave fabric-light exterior color combined with dark interior color for thermal comfort and view-through. GREENGUARD Children & Schools certified as a low emitting fabric. Manufacturer to supply GREENGUARD Children & Schools certificate. Fire rating: NFPA 701. SW2703-3 percent open.

B. Room Darkening Fabrics 1. SunBloc Series SB9100: Close woven fiberglass base textile with sun-resistant vinyl

film bonded to each side, opaque with minimum tensile strength of 190 pounds for warp and 180 pounds for fill. Fire rating: NFPA 701 1006-Test 1. Washable and stain resistant. Wt. 12 oz/sq yd. White exterior in all colors, .013 inches thick.

PART 3 EXECUTION

3.1 EXAMINATION

A. Do not begin installation until substrates have been properly prepared.

12 24 00-6

B. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

3.2 PREPARATION

A. Coordinate requirements for blocking and structural supports to ensure adequate means for installation of window shades.

B. Coordinate requirements for power supply conduit, and wiring required for window shade motors and controls.

3.3 INSTALLATION

A. Install in accordance with manufacturer's instructions.

B. Install roller shades level, plumb, square, and true. Allow proper clearances for window operation hardware.

C. Install the following items to conceal roller and operating mechanism. Do not use exposed fasteners. 1. Fascias.

3.4 TESTING AND DEMONSTRATION

A. Test motorized window shades to verify that controls, limit switches, interface to other building systems, and other operating components are functional. Correct deficiencies.

B. Test window shades to verify that operating mechanism, fabric retainer, and other operating components are functional. Correct deficiencies. 1. Chain and clutch. 2. Motorized Shades 3. Skylight Shades

C. Demonstrate operation of shades to Owner's designated representatives.

3.5 PROTECTION

A. Protect installed products until completion of project.

B. Touch-up, repair or replace damaged products before Substantial Completion.

3.6 SCHEDULES

A. Refer to Drawings for shade types and locations.

END OF SECTION

www.draperinc.com • 765-987-7999 13

A Premium Clutch FlexShade That Provides Smooth, Easy and Quiet OperationA premium clutch designed for the most demanding applications. Our XD clutch provides smooth, quiet operation even for larger clutch-operated shades.

• 1/8” thick steel mounting bracket with integrated XD Clutch

• XD clutch available in white (standard) or black color

• Internal rotation bearing ensures smooth, quiet operation

• Spline fabric attachment method allows for easy field replacement when necessary

• Centered bead chain exit allows for right or left hand operation with-out field modification

• Small and large hardware compatible with Draper U & H-channels or L-angles. No field modification required. Not usable with dual roller hardware. See page 20.

• Available with small and large hardware, and also dual roller con-figuration. Clutch FlexShade XD is compatible with standard Draper hardware offering (fascia, headbox, etc.)

• Includes wall mounting brackets and decorative plastic end cap covers as standard

• All Draper clutch-operated shades are provide with a “P” style chain hold down as standard. A spring-tensioned chain hold down is avail-able upon request

• 25-year limited warranty

Dual RollerHardware

Large Hardware

SmallHardware

43/4”

7”

45/8”

45/8”

33/8”

37/8”

Clutch FlexShade XD

Dimensions, drawings and specifications available at:www.draperinc.com/go/ClutchFlexShadeXD.htm

DUAL ROLLEROPTION

CLUTCHOPERATION

Dealer: Intex Design, Raleigh, NC. Photographer: Alex Krall

Motorized FlexShade SystembyPlease check all appropriate selections and attach room schedule with verifi ed dimensions.

Copyright © 2009 Draper Inc. Form Motorized FlexShades_Sub09 Printed in U.S.A.

PROJECT:

ARCHITECT:

CONTRACTOR:

SUPPLIER:

DATE: REVISED:

®

Select Installation Option Inside (head/sill, jamb/jamb) Outside (overlap opening) Coupled Shades (How many? ) Do any units abut at mullions? Which? Do any units install in pocket at ceiling?

Which? Select Motor and Control Options

Standard 110-120V AC Motors Standard Motor Quiet Motor Controls 110-120V Wall Switch for Single Shade Control Low Voltage and/or Multiple Shade Control**Please see Draper's IntelliFlex® Control System Selection Sheet to design a control solution for this product. The form is available at www.draperinc.com, or by contacting Draper.

Radio Technology Motors 110-120V AC Radio Technology Motor 110-120V AC Radio Technology Quiet Motor 24V DC Radio Technology Quiet Motor Controls Altus RF 1-Channel Transmitter 4-Channel Transmitter 5-Channel Transmitter with scroll wheel Dry Contact Interface Single Motor Sun Sensor (Circle one: White/Ivory) Wireless Wall Switch 1-Channel (Circle one: White/Ivory) 4-Channel (Circle one: White/Ivory) Chronis 1-Channel with 24-hour Timer Multi-Link Universal RTS Interface (5-channel) Multi-Link RS232 to RTS Interface (16-channel) Transformer (24V DC ONLY) Plug-In 1 Motor 3 Motors 6 Motors 9 Motors 12 Motors Din-Rail Mount 3 Motor 6 Motors 12 Motors

Intelligent Technology (ILT) 110-120V Motors Standard ILT 110-120V Motor Quiet ILT 110-120V Controls 1-Channel RF Transmitter 4-Channel RF Transmitter 5-Channel RF Transmitter with Scroll Wheel 1-Channel IR Transmitter Wireless Wall SwitchSelect Operator LocationSelect right side (standard) or left side as seen from inside the room, facing the window. Also indicate selection on room schedule.

Right Side (standard) Left Side

Select Fabric Orientation Regular Roll (from back of roller) Reverse Roll (from front of roller)

* Sizes requiring large endcaps/brackets will vary according to fabric.

Available Sizes*

Large endcaps/brackets and 3" roller may be required.

Small endcaps/brackets and 2" roller are recommended. 2' 3' 4' 5' 6' 7' 8' 9' 10' 11' 12' 13' 14'

Hei

ght

Width

2'3'4'5'6'7'8'9'

10'11'12'13'14'

24V DC Motor available on shades through 8' x 8'.

Call Draper for size limitations when using quiet motors.

Select Fabric* Color name, no. & openness CL8000 (Colony) "E" Screen by Mermet Flocké by Mermet Linen Veil by Newcastle "M" Screen by Mermet Obion by Mermet R1 by Mermet Roc-Rol by Rockland SheerWeave® Infi nity SheerWeave® PW3500/4100/4400 SheerWeave® PW4500/4600 SheerWeave® PW4550/4650 SheerWeave® PW4800 SheerWeave® SW2000/2100 SheerWeave® SW2400/2500/2600/2900 SheerWeave® SW2700/2701 SheerWeave® SW3000 SheerWeave® SW5000 SheerWeave® SW7000 SheerWeave® SW7100 SilverScreen by Mermet Soltis 99® by Ferrari SunBloc SB9000 SunBloc SB9100 "T" Screen by Mermet Terra by Mermet Vela by Mermet

*Please see Draper's Shade Fabric Reference Sheet for fabric colors and specifi cations.Select Hardware

Brackets Inside/Outside Ceiling

Fascia Optional Headbox

Surface Style Pocket Style

Optional Type "D" Pocket with Tile Lip (White only—not available with 3" roller) Optional Channels for Light Gap Reduction

¾" x 1" x 12'3" "L" Channels (Or Indicate Cut Length: ) 1" x 2¾" x 16' "L" Channels (Or Indicate Cut Length: ) 1" x 2½" x 16' "U" Channels (Or Indicate Cut Length: )Select Hardware Finish (does not apply to Type D Headbox)

Clear Anodized (standard) Black Ivory White Bronze

Motorized FlexShade System by Draper Page 2 of 4Specifi cationsStandard and Quiet 110-120V AC MotorsEquipmentElectric Operator: Drive unit inside roller, 4-wire, instantly re vers ible, lifetime lubricated. Right hand motor location standard. Left hand available. Adjustable limit switches, thermal overload protector and electric brake. Operates on 110-120V AC 1 PH 60 HZ current. Draws 1.1 Amps. For controls, see IntelliFlex® Controls Reference Sheet and IntelliFlex Controls Planning Sheet.Quiet Electric Operator: Drive unit inside roller, 4-wire, instantly re vers ible, lifetime lubricated. Right hand motor location standard. Left hand available. Adjustable limit switches, thermal overload protector and electric brake. Operates on 110-120V AC 1 PH 60 HZ current. Draws 1.1 Amps. Operates at or below sound level of 44 Db. For controls, see IntelliFlex® Controls Reference Sheet and IntelliFlex Controls Planning Sheet. Call Draper for size limitations when using quiet motors.HardwareRollers: Extruded aluminum or steel. Roller as sem bly easily re mov able.Mounting Brackets: 1018 plated steel stamping. Sizes 15/8" and 2¼". Styles for mounting to wall, ceiling, or jamb. Brackets do not require additional adapters.Roller Idler Assembly: Type 6/6 injected molded nylon and a zinc-plated cold rolled steel pin. Sliding pin for easy installation and removal of the roller. Slat: Aluminum, min. 1/8" x 1", encased in heat seamed hem.Endcaps: 1028 steel stamping. 2 sizes: 3¼" x 3¾" and 4½" x 4½". Complete with adapter roller bracket. Installs to wall, ceiling, or jamb. Accepts fascia or headbox.Endcap Covers: Plastic covers snap onto endcaps. Available in ivory, bronze, black or white to match fascia.Fascia: L-shaped cover of extruded aluminum, .060 wall. Assembly snaps onto endcaps without exposed fasteners. Clear Anodized (standard), black, white, ivory, or bronze powder coat fi nish available. Continuous fascia available with coupled units.Headbox: Standard consists of fascia, L-shaped back/top cover. Assembly snaps onto endcaps. Optional, for pocket installation, includes a U-shaped back/top/front cover with removable bottom closure panel. Small size: 315/16" x 37/16". Large size: 411/16" x 411/16". Some exposed fasteners required.Type D Pocket: Type D Shade pocket to be fabricated of 6063–T5 aluminum alloy for perimeter installation. Accepts FlexShades installed with ceiling brackets. Finished in white paint. 41/2" x 45/8" x .125" with tile support lip and removable bottom closure. Not available with 3" roller."L" Channel (¾" x 1" x 12'3", 1" x 2¾" x 16' or cut to length) and "U" Channel (1" x 2½" x 16' or cut to length): Accepts side edges of fabric, prevents light gaps. Interior of channel provides for use of fl at head screws.Coupler Assembly: Zinc plated steel Coupler Shafts shall be retractable into coupler assembly for ease of installation and to lock units in place. Zinc plated steel coupler brackets shall have spherical OD bearings allowing for misalignment of the mounting brackets of up to 1.25-degrees. One motor or crank operator to drive additional shade rollers.Please note: Dimensions of rollers, operators and hardware at man u fac tur er’s discretion.110-120V AC Radio Technology Standard and Quiet MotorEquipmentQuiet Electric Operator: Drive unit inside roller, 3-wire, instantly re vers ible, lifetime lubri-cated. Right hand motor location standard. Left hand available. Built-in radio receiver. Limit switches adjustable using wall switch or remote control.Thermal overload protector and electric brake. Operates on 110-120V AC 1 PH 60 HZ current. Draws 1.1 Amps. Operates at or below sound level of 44 Db. Call Draper for size limitations when using quiet motors.HardwareRollers: Extruded aluminum or steel. Roller as sem bly easily re mov able.Mounting Brackets: 1018 plated steel stamping. Sizes 15/8" and 2¼". Styles for mounting to wall, ceiling, or jamb. Brackets do not require additional adapters.Roller Idler Assembly: Type 6/6 injected molded nylon and a zinc-plated cold rolled steel pin. Sliding pin for easy installation and removal of the roller. Slat: Aluminum, min. 1/8" x 1", encased in heat seamed hem.Endcaps: 1028 steel stamping. 2 sizes: 3¼" x 3¾" and 4½" x 4½". Complete with adapter roller bracket. Installs to wall, ceiling, or jamb. Accepts fascia or headbox.Endcap Covers: Plastic covers snap onto endcaps. Available in ivory, bronze, black or white to match fascia.Fascia: L-shaped cover of extruded aluminum, .060 wall. Assembly snaps onto endcaps without exposed fasteners. Clear Anodized (standard), black, white, ivory, or bronze powder coat fi nish available. Continuous fascia available with coupled units.Headbox: Standard consists of fascia, L-shaped back/top cover. Assembly snaps onto endcaps. Optional, for pocket installation, includes a U-shaped back/top/front cover with removable bottom closure panel. Small size: 315/16" x 37/16". Large size: 411/16" x 411/16". Some exposed fasteners required.Type D Pocket: Type D Shade pocket to be fabricated of 6063–T5 aluminum alloy for perimeter installation. Accepts FlexShades installed with ceiling brackets. Finished in white paint. 41/2" x 45/8" x .125" with tile support lip and removable bottom closure. Not available with 3" roller."L" Channel (¾" x 1" x 12'3", 1" x 2¾" x 16' or cut to length) and "U" Channel (1" x 2½" x 16' or cut to length): Accepts side edges of fabric, prevents light gaps. Interior of channel provides for use of fl at head screws.Coupler Assembly: Zinc plated steel Coupler Shafts shall be retractable into coupler assembly for ease of installation and to lock units in place. Zinc plated steel coupler

Downloadable 3-part specifi cations are available at www.draperinc.com.

brackets shall have spherical OD bearings allowing for misalignment of the mounting brackets of up to 1.25-degrees. One motor or crank operator to drive additional shade rollers.Please note: Dimensions of rollers, operators and hardware at man u fac tur er’s discretion.24V DC Radio Technology Quiet MotorEquipment24 Volt Quiet Operator: Drive unit inside roller, instantly re vers ible, lifetime lubricated. Right hand motor location standard with endcaps; Left hand location standard with brackets. Left hand motor location also available with endcaps. Right hand motor location not available with brackets. Limit switches adjustable using wall switch or remote control. Operates at or below sound level of 44 Db. Call Draper for size limitations when using quiet motors.HardwareRollers: Extruded aluminum. Roller as sem bly easily re mov able.Mounting Brackets: 1018 plated steel stamping universal bracket for mounting to wall, ceiling, or jamb. Brackets do not require additional adapters.Roller Idler Assembly: Type 6/6 injected molded nylon and a zinc-plated cold rolled steel pin, spring-loaded for easy installation and removal of the roller.Slat: Aluminum, min. 1/8" x 1", encased in heat seamed hem.Endcaps: 1028 steel stamping. 3¼" x 3¾". Complete with adapter roller bracket. Installs to wall, ceiling, or jamb. Accepts fascia or headbox. Clear Anodized (standard), black, white, ivory or charcoal bronze fi nish available.Endcap Covers: Plastic covers snap onto endcaps. Available in ivory, bronze, black or white to match fascia.Fascia: L-shaped cover of extruded aluminum, .060 wall. As sem bly snaps onto endcaps without exposed fasteners. Clear Anodized (standard), black, white, ivory, or bronze powder coat fi nish available.Headbox: Standard consists of fascia, L-shaped back/top cover. Assembly snaps onto endcaps. 37/16" x 315/16"."L" Angle (¾" x 1" x 12'3", 1" x 2¾" x 16' or cut to length) and "U" Channel (1" x 2½" x 16' or cut to length): Accepts side edges of fabric, prevents light gaps. Interior of channel provides for use of fl at head screws.Please note: Dimensions of rollers, operators and hardware at man u fac tur er’s discretion.110-120V AC ILT MotorsEquipmentElectric Operator: Drive unit inside roller, 3-wire, instantly re vers ible, lifetime lubricated. Right hand motor location standard. Left hand available. Built-in encoder and low voltage controller with data cable. Limit switches adjustable using wall switch or remote control. Thermal overload protector and electric brake. Operates on 110-120V AC 1 PH 60 HZ current. Draws 1.1 Amps.Quiet Electric Operator: Drive unit inside roller, 3-wire, instantly re vers ible, lifetime lubricated. Right hand motor location standard. Left hand available. Built-in encoder and low voltage controller with data cable. Limit switches adjustable using wall switch or remote control. Thermal overload protector and electric brake. Operates on 110-120V AC 1 PH 60 HZ current. Draws 1.1 Amps. Operates at or below sound level of 44 Db. Call Draper for size limitations when using quiet motors.HardwareRollers: Extruded aluminum or steel. Roller as sem bly easily re mov able.Mounting Brackets: 1018 plated steel stamping. Sizes 15/8" and 2¼". Styles for mounting to wall, ceiling, or jamb. Brackets do not require additional adapters.Roller Idler Assembly: Type 6/6 injected molded nylon and a zinc-plated cold rolled steel pin. Sliding pin for easy installation and removal of the roller. Slat: Aluminum, min. 1/8" x 1", encased in heat seamed hem.Endcaps: 1028 steel stamping. 2 sizes: 3¼" x 3¾" and 4½" x 4½". Complete with adapter roller bracket. Installs to wall, ceiling, or jamb. Accepts fascia or headbox.Endcap Covers: Plastic covers snap onto endcaps. Available in ivory, bronze, black or white to match fascia.Fascia: L-shaped cover of extruded aluminum, .060 wall. As sem bly snaps onto endcaps without exposed fasteners. Clear Anodized (standard), black, white, ivory, or bronze powder coat fi nish available. Continuous fascia available with coupled units.Headbox: Standard consists of fascia, L-shaped back/top cover. Assembly snaps onto endcaps. Optional, for pocket installation, includes a U-shaped back/top/front cover with removable bottom closure panel. Small size: 315/16" x 37/16". Large size: 411/16" x 411/16". Some exposed fasteners required.Type D Pocket: Type D Shade pocket to be fabricated of 6063–T5 aluminum alloy for pe-rimeter installation. Accepts FlexShades installed with ceiling brackets. Finished in white paint. 41/2" x 45/8" x .125" with tile support lip and removable bottom closure. Not available with 3" roller."L" Angle (¾" x 1" x 12'3", 1" x 2¾" x 16' or cut to length) and "U" Channel (1" x 2½" x 16' or cut to length): Accepts side edges of fabric, prevents light gaps. Interior of channel provides for use of fl at head screws.Coupler Assembly: Zinc plated steel Coupler Shafts shall be retractable into coupler assembly for ease of installation and to lock units in place. Zinc plated steel coupler brackets shall have spherical OD bearings allowing for misalignment of the mounting brackets of up to 1.25-degrees. One motor or crank operator to drive additional shade rollers.Please note: Dimensions of rollers, operators and hardware at man u fac tur er’s discretion.

www.draperinc.com (765) 987-7999

Headbox* Brackets Small Large Small LargeA¹ 315/16" 411/16" A² 21/2" 31/4"B¹ 17/8" 21/4" B² 13/8" 2"C¹ 15/8" 21/4" C² 15/8" 21/4"D¹ 37/16" 411/16" D² 3" 41/4" E² 31/16" 4"

110-120V Standard, Quiet and ILT Motorized FlexShade Dimensions

Hardware SelectionsNote: Brackets and endcaps have the only attachment points for mounting a motorized FlexShade. Optional fascia and headbox have a thickness of 1/16".

Headbox installation Options

Outside mounting bracket Ceiling mounting bracketInside mounting bracket Fascia only with ceiling/wall mounting endcaps

Surface style headbox consists of fascia, back/top cover and ceiling/wall mounting endcaps

Optional pocket style headbox consists of Draper’s extruded pocket with bottom closure panel and ceiling/wall mounting endcaps

41/2"

31/4" 7/8"1"

45/8"

Pocket OptionsType D pocket, white in color, features a 41/2" x 45/8" cross-section. A lip along lower edge supports lay-in ceiling. Pre-welded corners and pocket ends are available. Ends come with or without tile support lip (shown).

Typical pocket end (not to scale)

Typical pre-welded corner section (not to scale)

Cross Section of Type D Pocket

Endcap Covers

Motorized FlexShade System by Draper Page 3 of 4

www.draperinc.com (765) 987-7999

24 Volt Radio Technology Quiet FlexShade

Cloth width = Overall width - 21/4" (fascia)

Overallheight

Cloth width = Overall width - 21/8" (brackets)

24 Volt Radio Technology Quiet FlexShade Dimensions(Left-hand bracket

and endcap shown)

Cloth width = Overall width - 15/8"

Overall height

13/16" 13/16"

D2

C2

E2

B2 A2

5/16"

A1

B1

C1

D1

110-120V Standard and Quiet Motorized FlexShade

110-120V ILT Standard and Quiet Motorized FlexShade

"U" Channel "L" Angle

33/4" 2"

5/16"

31/4"

21/2"

2"

2"

11/4" 11/4"

17/8"

17/8"

*For fascia, subtract 1/16" from dimensions A and D

Motorized FlexShade System by Draper Page 4 of 4

www.draperinc.com (765) 987-7999

110-120V Standard and Quiet Shade Wiring Diagram

For multiple shade or low voltage wiring consult diagrams provided with control.

Internal Shade WiringWhite (Common)BlackRedGreen (Ground)

Controlswitch

Single gang box by othersMin. 4" x 2

1/8" x 1 7/8" deepRed

BlackBlack

To 110-120V Line

Dashed wiring by electrician

24V DC Quiet Shade Wiring Diagram

Radio FrequencyDC Switch

DC Motors

Transformer

120 V AC

Internal Screen Wiring

White (Neutral)

Black

Green (Ground)

Dashed wiring by electrician

To 110-120V Line

Wall Switchor RF

Receiver

Radio Technology110-120V MotorsSingle Low Voltage Control

Internal Shade Wiring

White (Neutral)

Black

Green (Ground)

Dashed wiring by electrician

To 110-120V Line

Multiple Low Voltage Controls Internal Shade Wiring

White (Neutral)

Black

Green (Ground)

Dashed wiring by electrician

To 110-120V Line

Wall Switch, RF or IR Receiver,

or integrated control system

Wall Switches, RF or IR

Receivers, or integrated

control systems

Data Cable

Data Cables

Optional splitter

OptionalModularSplitter

to 110-120V Power Supply (Dashed wiring by electrician)

Wall Switch,IR or RF Receiveror integrated control system

Data Cable

110-120V ILT Standard and Quiet Shade Wiring Diagrams

Multiple ILT Motors

Please check all appropriate selections and attach room schedule with fi eld verifi ed dimensions.

Select Fabric Indicate color name & no. “E” Screen from Mermet “M” Screen from Mermet SheerWeave® SW2000/2100 SheerWeave® SW2400/2500/2600/2900 SheerWeave® SW3000 Soltis 99® by Ferarri SunBloc SB9000 SunBloc SB9100 “T” Screen from Mermet

*Please see Draper's Shade Fabric Reference Sheet for fabric colors and specifi cations.

Skylight FlexShade System by

Copyright © 2012 Draper Inc. Form SkyLightFlexShade_Sub12 Printed in U.S.A.

PROJECT:

ARCHITECT:

CONTRACTOR:

SUPPLIER:

DATE: REVISED:

®

Select Hardware Finish Silver Black Ivory White Charcoal Bronze

Select Installation Option (see below) Inside Mount Outside Mount

Select Operator Location (see below) Location A Location C Location B Location D

Select Operator and Control Options Crank Operator with detachable crank.

Specify crank length (6' max.) Note: Crank operator units operable up to 10 feet above fl oor.

Standard 110-120V AC Motors Standard Motor Quiet Motor Controls 110-120V Wall Switch for Single Shade Control Low Voltage and/or Multiple Shade Control*Please see Draper's IntelliFlex Controls Reference Sheet and IntelliFlex® Control System Planning Sheet to design a control solution for this product. The forms are available at www.draperinc.com, or by contacting Draper.

Radio Technology Motors 110-120V AC Radio Technology Motor 110-120V AC Radio Technology Quiet Motor Controls Altus RF 1-Channel Transmitter 4-Channel Transmitter 5-Channel Transmitter with scroll wheel Dry Contact Interface Single Motor Sun Sensor (Circle one: White/Ivory) Wireless Wall Switch 1-Channel (Circle one: White/Ivory) 4-Channel (Circle one: White/Ivory) Chronis 1-Channel with 24-hour Timer Multi-Link Universal RTS Interface (5-channel) Multi-Link RS232 to RTS Interface (16-channel)

Intelligent Technology (ILT) 110-120V Motors Standard ILT 110-120V Motor Quiet ILT 110-120V Controls 1-Channel RF Transmitter 4-Channel RF Transmitter 5-Channel RF Transmitter with Scroll Wheel 1-Channel IR Transmitter Wireless Wall Switch

Maximum SkyLight FlexShade size is 6' wide x 8' high. If larger size is re-quired, contact Draper.

With outside mount in stal la tion, sep a rate head er bars must be at tached at both ends to house the sup port ca ble sys tem. With out side mount in stal la tion, fab ric stay pock ets are vis i ble from in side the room on all siz es of Sky light FlexShades (refer to drawings on page 1).

Fabric Support System Details

Glide strip

Flange/endcaplocator

Side support flange

Stay pocketSteel stay

Fabric

Take-up cable

Fabric guide

Support Cable Details

Fabric SupportSystem

Support cablesfor larger units.

Detachablecrank operator

Units between 36" wide and 72" wide (outside measure) require 1 support cable. Cables may also be used at Draper’s discretion. Ca bles are 3/16" di am e ter vinyl clad air craft ca ble. The ca bles are vis i ble from in side the room at all times.

Specifi cationsMethod Of OperationCrank Operator: Gear box, of die cast aluminum and steel, has ratio of 1.7:1 or 3:1. Bidirectional to mount at either end of the roll er. Never needs lu bri ca tion or adjust-ment. Crank handle as sem bly, of anodized alu mi num and chrome plat ed steel, in over all operating lengths to 6', detach able. Crank roller insert of in jec tion molded nylon and steel is in stalled in roller and en gag es to gear box. Maximum width 72"; maximum length 96".Electric Operator: Drive unit inside roller, 4-wire, instantly re vers ible, lifetime lubri-cated. Right hand motor location standard. Left hand available. Adjustable limit switches, thermal overload protector and electric brake. Operates on 110-120V AC 1 PH 60 HZ current. Draws 1.1 Amps. For controls, see IntelliFlex® Controls Refer-ence Sheet and IntelliFlex Controls Planning Sheet.Quiet Electric Operator: Drive unit inside roller, 4-wire, instantly re vers ible, lifetime lubricated. Right hand motor location standard. Left hand available. Adjustable limit switches, thermal overload protector and electric brake. Operates on 110-120V AC 1 PH 60 HZ current. Draws 1.1 Amps. Operates at or below sound level of 44 Db. For controls, see IntelliFlex® Controls Reference Sheet and IntelliFlex Controls Planning Sheet. Call Draper for size limitations when using quiet motors.RTS Electric Operator: Drive unit inside roller, 3-wire, instantly re vers ible, lifetime lubricated. Right hand motor location standard. Left hand available. Built-in radio receiver. Limit switches adjustable using wall switch or remote control.Thermal overload protector and electric brake. Operates on 110-120V AC 1 PH 60 HZ current. Draws 1.1 Amps. Operates at or below sound level of 44 Db. Call Draper for size limitations when using quiet motors.ILT Electric Operator: Drive unit inside roller, 3-wire, instantly re vers ible, lifetime lu-bricated.Right hand motor location standard. Left hand available. Built-in encoder and low voltage controller with data cable. Limit switches adjustable using wall switch or remote control. Thermal overload protector and electric brake. Operates on 110-120V AC 1 PH 60 HZ current. Draws 1.1 Amps.Quiet ILT Electric Operator: Drive unit inside roller, 3-wire, instantly re vers ible, life-time lubricated. Right hand motor location standard. Left hand available. Built-in encoder and low voltage controller with data cable. Limit switches adjustable using wall switch or remote control. Thermal overload protector and electric brake. Oper-ates on 110-120V AC 1 PH 60 HZ current. Draws 1.1 Amps. Operates at or below sound level of 44 Db. Call Draper for size limitations when using quiet motors.HardwareRollers: Motorized roller size 2" dia. x .080 wall, in ex trud ed aluminum . Spring take-up roller size 13/4", in sti tu tion al qual i ty, with heavy-duty springs, mount ed on one-piece electro-gal va nized steel roller. Roll er as sem bly easily removable.

Skylight FlexShade System by Draper Page 2 of 3

Downloadable 3-part specifi cations are available at www.draperinc.com.

Roller Idler Assembly: Injection molded plastic containing a spring-loaded steel pin for easy in stal la tion and removal of the roller.Endcaps: 1018 steel stamping: 31/4" x 33/4". Complete with adapt er roller bracket. Endcaps used for mounting of each headbox (en clo sure). Ac cepts box covers and fabric guides. Clear Anodized (standard), black, white, ivo ry, or charcoal bronze fi nish available.Operator and Take-up Enclosures, Side Support Flanges & Slat Bar: 6063-T5 alu mi num cus tom extruded shapes, .060 wall. Silver (standard), black, white, ivory, or charcoal bronze fi n ish available. All contain grooves to accept light seal elements.Operator and Take-up Enclosures consist of an L-shaped back/top and an L-shaped front/bot tom.Side Support Flange consists of two sections. One section contains grooves for the fabric guide, and a groove for the glide strip, which supports the slat bar, fabric and stays. The second section contains the fl ange/endcap locators. Outside mounts re quire plas tic cover buttons.Flange/Endcap Locator: Type 6 injection molded nylon. Aligns side support fl ange and endcap.Slat Bar provides an attachment point for the shade fabric and for the cable idler bearings. The idler bearings provide self-adjusting equalization of the cable tension at each end of the slat bar.Take-up Cable: 3/64" stainless steel, nylon coated, with a minimum breaking strength of 220 lbs. (100 kg); never visible during operation.Take-up Reel: 1/16" thick, machined 6061-T6 aluminum assures that take-up cable remains in proper alignment.Fabric Guide: Plated steel. Forms a transition for the fab ric as it rolls into the chan- nels, reducing friction.Opacity Plates: 1018 steel with a rubber “O” ring. Installed on the endcaps of the roller box to elim i nate light leakage.Fabric Support System: Horizontal steel stays are in stalled at reg u lar intervals and covered. This system enables the shade to with stand rea son able air pres sure differentials and gravity. Please note: Extreme air currents or physical in ter fer ence may cause product failure.Support Cable(s): .062" dia. strand ed steel ca ble with clear vinyl coat ing. One end attached at op er a tor enclosure, other end at take-up en clo sure, spaced at 21" to 36" in ter vals. Attachment brackets: 1018 weld ed steel zinc plat ed. Turnbuck les are com bi na tion of die-cast aluminum and steel. Units between 36" wide and 72" wide (outside measure) require 1 support cable. Cables may also be used at Draper’s discretion.

www.draperinc.com (765) 987-7999

Dimensions

(Inside Mount Installation shown)

3/4"

23/4"

Take-up reel

Access cover

2" dia. motorized roller

Flange/endcap locator

Side support flange

Glide strip

3/4" x 1" adjustable mounting angles

Access cover

13/4" dia.spring roller

Shims at both ends

Back cover

3/4" x 1" perimeter support angle

Side support flange

Cloth

Slat bar

Take-up cable Back cover

Direction of fabric travel

37/16"

315/16" 315/16"

37/16"

Single Shade Wiring Diagram Minimum Shade Width Outside Measure Inside Measure11/2" Spring-Roller 28-5/8" 29-3/8"13/4" Spring-Roller 34-3/8" 35-1/8"21/4" Spring-Roller 48-3/4" 49-1/2"

Maximum Shade Length11/2" Spring-Roller 96"13/4" Spring-Roller 96"21/4" Spring-Roller 96"

For multiple shade or low voltage wiring consult diagrams provided with control.

Internal Shade WiringWhite (Common)BlackRedGreen (Ground)

Controlswitch

Single gang box by othersMin. 4" x 2

1/8" x 1 7/8" deepRed

BlackBlack

To 110-120V Line

Dashed wiring by electrician

NOTE: Test shade operation. If shade direction does not correspond with the switch orientation, turn power back off and switch the red and black wires from the motor to the switch.

Maximum SkyLight FlexShade size is 6' wide x 8' high. If larger size is re-quired, contact Draper.

Skylight FlexShade System by Draper Page 3 of 3

www.draperinc.com (765) 987-7999

Outside Mount

InstallationInside Mount

Operator LocationsChoose location A, B, C or D. For motorized units, Draper standardly supplies 6' motor lead wire. Indicate additional lead if required, up to 16' total.

Inside MountA

B

C

D

Outside MountA

B

C

D

www.draperinc.com • 765-987-79994

Motorized FlexShadeThe simplicity of shades with the versatility of motorized operation.• Motorized FlexShades are available in any size from 2´

through ´ wide. Larger sizes are available with FlexShade 2 or Colossal FlexShade.

• Furnished with mounting brackets. Optional fascia cover, headbox, and extruded aluminum pockets with bottom closure are available. See pages 16 & 17 for hardware details.

• Multiple Motorized FlexShades can be coupled together to reduce the number of motors required. See page 16.

• Available with a variety of motor options including: quiet, built-in radio frequency control, battery or low voltage operation. Motors are installed on the right-hand side as standard. They may be specified on the left. See page 7 for details.

• Wall switch included with each shade, or choose one of our versatile control options. Details on pages 7 and 8.

• Depending on size of shade, battens may be used to assure a smooth flat surface.

More detailed information, including dimensions, drawings and specifications available at: www.draperinc.com/go/MotorizedShade.htm

Motorized FlexShade Dimensions

Standard bracket

Optional endcap and fascia

Cloth width = Overall width - 15/8"

Overall height

13/16" 13/16"

E 1

B 2

A2

A1

B1

D1

E 1C1

C2

Consult Draper to determine which size is required for your installation

7 World Trade CenterShown here and on the front cover, 7 World Trade Center was the first structure built on

the site of ground zero following the terrorist attacks of September 11, 2001.

Certified LEED® Gold, 7 World Trade Center utilizes Draper Motorized and Manual

FlexShades with Phifer SheerWeave® 2700 fabric to reduce glare, conserve energy, and

add privacy in busy downtown New York City. Installed by International Blind Contractors,

LTD. Architect: David M. Childs.

Headbox with Endcaps

Fascia with Endcaps

Standard Brackets

Small Large Small Large Small Large

A¹ 315/16˝ 411/16˝ 37/8˝ 45/8˝ A² 21/2˝ 31/4˝

B¹ 37/16˝ 411/16˝ 33/8˝ 45/8˝ B² 15/8˝ 21/4˝

C¹ 11/2˝ 15/8˝ 11/2˝ 15/8˝ C² 3/4˝ 3/4˝

D¹ 5/8˝ 5/8˝ 5/8˝ 5/8˝

E¹ 1/16˝ 3/32˝ 1/16˝ 3/32˝