Sangoma-w400 Interfacecard Setupguide

7/21/2019 Sangoma-w400 Interfacecard Setupguide

http://slidepdf.com/reader/full/sangoma-w400-interfacecard-setupguide 1/9

Sangoma W and Elastix Server

http://www.elastix.org


Setu


p Guide



1.0 Setup Diagr

Figure 1-1 is a setup

2.0 Host PC Env

Ta

Hardware Type

Hardware Version

Software Type

Software Version

3.0 Test Setup E

Equipment

IP (SIP) Phone

Sangoma

Switch

PaloSant

Sangoma W400 and Elastix Server S

2

m

iagram for a single Sangoma W400 Interface Ca

Figure 1-1. Setup Diagram

ironment

ble 2-1. Host Server Environment Details

Description

Elastix Appliance ELX-Series

ELX-3000

Elastix

2.3

quipment

Table 3-1. Test Setup Equipment

Model Versi

N/A N/

W400 Wanpipe-uti

Asterisk

N/A N/

o Solutions

tup Guide

rd configuration.

on

l-3.5.28-0

1.8.18



PaloSanto Solutions

Sangoma W400 and Elastix Server Setup Guide

3

4.0 Setup Procedure

To set up the Elastix Server for the Sangoma W400 Interface Card,

1. Go to the web address of the Elastix Server Login page. The web address is

determined by the customer, for this guide we have used the IP address

192.168.1.75

2. On the Login page, type the username and password for an administrative user into

the Username and Password fields, see Figure 4-1. The username and password are

determined by the customer.

Figure 4-1. Login

3. Press Enter or click on the Submit button to go to Elastix’s Dashboard

4. Once inside, click on the System tab on the menu at the top of the screen

Figure 4-2. Dashboard

5. Now, click on “Hardware Detector”. This will take you to set some parameters for

detecting new hardware in Elastix, see Figure 4-3.



6. Click on “Advan Now click on “D

7. If the interface ca

bottom of the pag

8. You can configu

Span” (Figure 4-

PaloSant


4

Figure 4-3. Hardware Detector

ce” checkbox and select “Replace file chan_dtect New Hardware” (Figure 4-4).

Figure 4-4. Hardware Detector

rd is successfully detected you should see the 4 s

e. It should say “Detected by Asterisk”. (Figure

Figure 4-5. Hardware Detection

re ports for echo cancellation by clicking on

) located on the left side of the detected ports

o Solutions

tup Guide

hdi.conf” option.

pans shown at the

-5).

Configuration of



9. You can change t

10. Go to “PBX => P

11. Go to “Extension

IPPhone. In the

8):

Add Extension

• User Extensi

• Display nam

Device Options

• Secret: (“h7

PaloSant


5

Figure 4-6. Configuration of Span

his value according to your needs.

BX Configuration” (Figure 4-7)

Figure 4-7. PBX

s” and select “Generic SIP Device” to create an

dd SIP Extension page fill in the following info

on: (302 in this example)

e: (“IPPhone” in this example)

ka3Rf9si0t” in this example)

Figure 4-8. Add SIP Extension

o Solutions

tup Guide

extension for the

mation (Figure 4-



12. Click on “Submi

“Trunks” on the l

13. On the Add DA

General Settings

•

Trunk Nam

Outgoing Settings

• DAHDI Ide

The number 1 is the

card located in the fir

PaloSant


6

” located at the end of the page and apply chan

eft side and select “Add DAHDI Trunk” (Figure

Figure 4-9. Trunks

DI Trunk page, set the following (Figure 4-10).

: (“Sangoma_Trunk ” in this example)

tifier: 1

hannel we’ll use for outbound calls. In this case

st span.

Figure 4-10

o Solutions

tup Guide

es. Now, click on

4-9).

we have the GSM



PaloSanto Solutions

Sangoma W400 and Elastix Server Setup Guide

7

14. Click on “Submit Changes” button located at the end of the page. Go to “PBX =>

PBX Configuration => Outbound Routes”. Click on “Add Route” (Figure 4-11). Set

the following:

Route Settings

• Route Name: (“9_Outside” in this example)

Dial patterns

• Prefix: (“9” in this example) | Match pattern: (“.” in this example)

Trunk Sequence for Matched Routes

• 0: The trunk that we just created (“Sangoma_Trunk ” in this example)

Figure 4-11. Outbound Route

15. Now you can make outbound calls through the SIMCARD calling a telephone

number with “9” as prefix.

16. We’ll create an incoming route for the calls from any external number to our SIMCARD. We’re going to use an IVR for incoming calls. Go to “PBX => PBXConfiguration => IVR”. Click on “Add IVR” (Figure 4.12). Set the following:

• Name: Name of IVR (WelcomeIVR in this example)

• Announcement: Record which will be played for incoming calls.

• Options:o * - Phone book.

o 0 - 302 Extension

o t - Repeat the options of IVR (Add this option by modifying the

IVR after creation)



17. Click on “Save”the top of the paClick on “Add In

• Descripti

• Set desti example)

18. Click on “Sub

SIMCARD the “

to interact with E

19. Configure the IP

20. To test the confi

dial a mobile ph

phone and verif

mobile phone calshould be interact

PaloSant


8

Figure 4-12. IVR

and Apply changes by clicking on the pink ribbe. Now go to “PBX => PBX Configuration =>

coming Route”. (Figure 4.13). Set the following:

on: Name of inbound route (“Incoming_Calls” i

ation: Where the call will be routed. (“Welcom

Figure 4-13. Incoming Route

it” and apply changes. Now when we rec

elcomeIVR” IVR will be played to the caller g

lastix Server.

(SIP) Phone with the correct parameters.

gurations, pick up the previously configured IP

ne with “9” as prefix. When the call is establish

that the mobile phone can hear your voice.

l to the SIMCARD number and when the calling with the IVR.

o Solutions

tup Guide

on that appears at Inbound Routes”.

this example)

eIVR” IVR in this

ive calls to the

iving him choices

(SIP) Phone and

ed, speak into the

Next, from your

is established you

Sangoma-w400 Interfacecard Setupguide

Documents

Transcript of Sangoma-w400 Interfacecard Setupguide