SANDEN/R-4 MULTI-GROOVE COMPRESSOR CONVERSION BRACKET 141805

T M Bracket Systems - SANDEN/R-4 MULTI-GROOVE COMPRESSOR CONVERSION BRACKET 141805 1. 2. No. QTY. PART No. DESCRIPTION 2 1 1 2 146008 191012 SANDEN/R-4 BRACKET ADAPTER SANDEN/R-4 CONVERSION HARDWARE KIT 901805 REV B 09/24/19 SANDEN/R-4 CONVERSION KIT INST PG 1 OF 1 CHECKED BY: PACKED BY: DATE: NOTE: FAILURE TO FOLLOW THESE PROCEDURES WILL VOID ALL WARRANTIES. VINTAGE AIR RECOMMENDS USING ONLY DAYCO, GATES, OR GOODYEAR BRAND REINFORCED BELTS WITH THIS COMPRESSOR. ANY USE OF LESSER QUALITY BELTS MAY CAUSE COMPRESSOR TO PERFORM IMPROPERLY. WHEN MOUNTING & ADJUSTING YOUR BELT MAKE SURE THE OIL PLUG CENTERLINE DOES NOT EXCEED 90° FROM VERTICAL IN EITHER DIRECTION TO AVOID COMPRESSOR FAILURE. DO NOT CONNECT COMPRESSOR CLUTCH WIRE UNTIL SYSTEM IS BEING CHARGED w/REFRIGERANT. RUNNING COMPRESSOR WITHOUT REFRIGERANT WILL VOID WARRANTY! IMPORTANT NOTICE MOUNTING & BELT ADJUSTMENT DIAGRAM COMPRESSORS ARE FACTORY CHARGED w/ OIL CENTER LINE OIL PLUG SD-508 90° 90° INSTALL THE SANDEN/R-4 BRACKET ADAPTERS ONTO THE COMPRESSOR AS SHOWN IN FIGURE 1, BELOW. INSTALL THE COMPRESSOR/BRACKET ASSEMBLY ONTO THE OEM BRACKET AS SHOWN IN FIGURES 1 & 2, BELOW. OEM BRACKET 10mm NYLON LOCKNUT 18014-VUB 10mm x 50mm SOCKET CAP SCREW 18015-VUB 10mm x 40mm SOCKET CAP SREW 18007-VUB 3/8” STEEL SPACER 1/8” STEEL SPACER FIGURE 2 REMOVE METAL SLEEVE OEM BRACKET (6)10mm NYLON LOCKNUTS 18014-VUB FIGURE 1 11/16” STEEL SPACER (4)10mm x 40mm SOCKET CAP SCREWS 18007-VUB (2) SANDEN/R-4 BRACKET ADAPTERS 146008

Upload
others
Category

Documents
view
8
download
0

Embed Size (px):

Transcript of SANDEN/R-4 MULTI-GROOVE COMPRESSOR CONVERSION BRACKET 141805

TM Bracket Systems

-SANDEN/R-4 MULTI-GROOVE COMPRESSOR CONVERSION BRACKET 141805

1.2.

No. QTY. PART No. DESCRIPTION21

1 2

146008191012

SANDEN/R-4 BRACKET ADAPTERSANDEN/R-4 CONVERSION HARDWARE KIT

901805 REV B 09/24/19 SANDEN/R-4 CONVERSION KIT INST PG 1 OF 1

CHECKED BY:PACKED BY:

DATE:

NOTE: FAILURE TO FOLLOW THESE PROCEDURES WILL VOID ALL WARRANTIES.

VINTAGE AIR RECOMMENDS USING ONLY DAYCO, GATES, OR GOODYEAR BRAND REINFORCED BELTS WITH THIS COMPRESSOR. ANY USE OF LESSER QUALITY BELTS MAY CAUSE COMPRESSOR TO PERFORM IMPROPERLY.

WHEN MOUNTING & ADJUSTING YOUR BELT MAKE SURE THE OIL PLUGCENTERLINE DOES NOT EXCEED 90° FROM VERTICAL IN EITHER DIRECTIONTO AVOID COMPRESSOR FAILURE.

DO NOT CONNECT COMPRESSOR CLUTCH WIRE UNTIL SYSTEMIS BEING CHARGED w/REFRIGERANT. RUNNING COMPRESSORWITHOUT REFRIGERANT WILL VOID WARRANTY!

IMPORTANT NOTICE

MOUNTING & BELTADJUSTMENT DIAGRAM

COMPRESSORS AREFACTORY CHARGED

w/ OIL

CENTER LINEOIL PLUG

SD-508

90°90°

INSTALL THE SANDEN/R-4 BRACKET ADAPTERS ONTO THE COMPRESSOR AS SHOWN IN FIGURE 1, BELOW.INSTALL THE COMPRESSOR/BRACKET ASSEMBLY ONTO THE OEM BRACKET AS SHOWN IN FIGURES 1 & 2, BELOW.

OEMBRACKET

10mm NYLON LOCKNUT

18014-VUB

10mm x 50mmSOCKET CAP SCREW

18015-VUB

10mm x 40mmSOCKET CAP SREW

18007-VUB

3/8”STEEL SPACER

1/8”STEEL SPACER

FIGURE 2

REMOVEMETAL SLEEVE

OEMBRACKET