SAILOR 6216 VHF DSC - Telemar Norge · SAILOR 6216 VHF DSC User and installation manual Document...

USER & INSTALLATION MANUAL

SAILOR 6216 VHF DSC

Thrane & Thrane A/S

SAILOR 6216 VHF DSC

User and installation manual

Document number: 98-128825-THR-E

Release date: December 18, 2012

Disclaimer

Any responsibility or liability for loss or damage in connection with the use of this

product and the accompanying documentation is disclaimed by Thrane & Thrane. The

information in this manual is provided for information purposes only, is subject to

change without notice and may contain errors or inaccuracies.

Manuals issued by Thrane & Thrane are periodically revised and updated. Anyone

relying on this information should acquire the most current version e.g. from the Thrane

& Thrane Extranet at: http://extranet.thrane.com.

Thrane & Thrane is not responsible for the content or accuracy of any translations or

reproductions, in whole or in part, of this manual from any other source.

Copyright

© 2012 Thrane & Thran3 A/S. All rights reserved. Printed in Denmark.

Trademark Acknowledgements

• SAILOR is a registered trademarks of Thrane & Thrane A/S.

• Other product and company names mentioned in this manual may be trademarks or

trade names of their respective owners.

http://extranet.thrane.com

Safety warning 1

The following general safety precautions must be observed during all

phases of operation, service and repair of this equipment. Failure to comply

with these precautions or with specific warnings elsewhere in this manual

violates safety standards of design, manufacture and intended use of the

equipment. Thrane & Thrane assumes no liability for the customer's failure

to comply with these requirements.

Warranty limitation

IMPORTANT - The radio is a sealed waterproof unit (classified IPX8). To

create and maintain its waterproof integrity it was assembled in a controlled

environment using special equipment. The radio is not a user maintainable

unit, and under no circumstances should the unit be opened except by

authorized personnel. Unauthorized opening of the unit will invalidate the

warranty.

Installation and service

Installation and general service must be done by skilled service personnel.

iii

iv

Emergency calls

MMMMMAAAAAYYYYYDDDDDAAAAAYYYYYNANANANANAMEMEMEMEME of the VVVVVEEEEESSSSSSSSSSELELELELEL in distress

CCCCCALALALALALLLLLLSSSSSIGNIGNIGNIGNIGN or other IDENIDENIDENIDENIDENTTTTTIFICIFICIFICIFICIFICAAAAATTTTTIONIONIONIONION

MMMMMMMMMMSSSSSIIIII

(If the initial alert is sent by DSC)

PPPPPOOOOOSSSSSITITITITITIONIONIONIONIONgiven as lllllatatatatatitititititudeudeudeudeude and longitlongitlongitlongitlongitudeudeudeudeude

or

If latitude and longitude are not known

or if time is insufficient,

in relation to a known geographical location

NANANANANATURETURETURETURETURE of distress

Kind of AAAAASSSSSSSSSSIIIIISSSSSTTTTTANCANCANCANCANCEEEEE required

Any other useful INFINFINFINFINFORORORORORMMMMMAAAAATTTTTIONIONIONIONION

MMMMMAAAAAYYYYYDDDDDAAAAAYYYYY-M-M-M-M-MAAAAAYYYYYDDDDDAAAAAYYYYY-M-M-M-M-MAAAAAYYYYYDDDDDAAAAAYYYYYThis is

NANANANANAME-NAME-NAME-NAME-NAME-NAME-NAME-NAME-NAME-NAME-NAMEMEMEMEME

CCCCCALALALALALLLLLLSSSSSIGNIGNIGNIGNIGNor other IDENTIFICATION

MMMMMMMMMMSSSSSIIIII(If the initial alert is sent by DSC)

Use the HANDMICHANDMICHANDMICHANDMICHANDMICRRRRROPOPOPOPOPHONE HONE HONE HONE HONE for voice calling

MMMMMakakakakake sure sure sure sure sure e e e e youryouryouryouryour VVVVVHFHFHFHFHF R R R R Radiadiadiadiadio o o o o iiiiis on Cs on Cs on Cs on Cs on CH1H1H1H1H166666

LLLLLififififift Ct Ct Ct Ct Covovovovovererererer

PPPPPrrrrreeeeessssss RED Buttons RED Buttons RED Buttons RED Buttons RED Buttonuntil acoustic and light-indication

becomes steady (more than 3 seconds)

SHIP‘s NAME:

CALLSIGN:

MMSI:

OWN OWN OWN OWN OWN IDIDIDIDID

99-129558

Training information 2

The SAILOR 6216 VHF DSC is designed for "occupational use only"

and is also classified as such. It must be operated by licensed

personnel only. It must only be used in the course of employment

by individuals aware of both the hazards as well as the way to

minimize those hazards

The radio is thus NOT intended for use in an uncontrolled

environment by general public. The SAILOR 6216 VHF DSC has

been tested and complies with the FCC RF exposure limits for

"Occupational Use Only". The radio also complies with the

following guidelines and standards regarding RF energy and

electromagnetic energy levels including the recommended levels

for human exposure:

• FCC OET Bulletin 65 Supplement C, evaluating compliance with

FCC guidelines for human exposure to radio frequency

electromagnetic fields.

• American National Standards Institute (C95.1) IEEE standard for

safety levels with respect to human exposure to radio frequency

electromagnetic fields, 3 kHz to 300 GHz

• American National Standards Institute (C95.3) IEEE

recommended practice for the measurement of potentially

hazardous electromagnetic fields - RF and microwaves.

Below the RF exposure hazards and instructions in safe operation

of the radio within the FCC RF exposure limits established for it are

described.

Warning

Your Thrane & Thrane radio set generates electromagnetic RF

(radio frequency) energy when it is transmitting. To ensure that

you and those around you are not exposed to excessive amounts of

that energy (beyond FCC allowable limits for occupational use) and

thus to avoid health hazards from excessive exposure to RF

energy, FCC OET bulletin 65 establishes an Maximum Permissible

Exposure (MPE) radius of 3 ft (0.9m) for the maximum power of

v

your radio (25W selected) with an half wave omni-directional

antenna having a maximum gain of 3 dB (5.2dBi). This means all

persons must be at least 3 ft (0.9m) away from the antenna when

the radio is transmitting.

Installation

1. An omni-directional antenna with a maximum power gain of

5.2 dBi must be mounted at least 9.6 ft (2.9m) above the

highest deck where people may be staying during radio

transmissions. The distance is to be measured vertically from

the lowest point of the antenna. This provides the minimum

separation distance which is in compliance with RF exposure

requirements and is based on the MPE radius of 3 ft (0,9m)

plus the 6.6 ft (2m) height of an adult.

2. On vessels that cannot fulfil requirements in item 1, the antenna

must be mounted so that its lowest point is at least 3 ft (0.9m)

vertically above the heads of people on deck and all persons

must be outside the 3 ft (0.9m) MPE radius during radio

transmission.

• Always mount the antenna at least 3ft (0.9m) from possible

human access.

• Never touch the antenna when transmitting

• Use only authorized T&T accessories.

3. If antenna has to be placed in public areas or near people with

no awareness of the radio transmission, the antenna must be

placed at a distance not less than 6 ft (1.8m) from possible

human access.

Failure to observe any of these warnings may cause you or other

people to exceed FCC RF exposure limits or create other dangerous

conditions

vi

Manual overview

This manual has the following chapters:

• Introduction contains a description of the VHF radio.

• Operation explains how to make and receive voice and DSC

calls over VHF, including how to use and set-up the channel

scanning, the 2-way loudhailer, fog horn external loudspeaker.

• Installation explains how to mount the VHF radio and how to

connect accessories and external equipment.

• Service & maintenance contains support information including

lists of accessories and a troubleshooting guide.

vii

Table of Contents

Chapter 1 Introduction

VHF radio with DSC ............................................................ 1

Chapter 2 Operation

General use and navigation .............................................. 6

VHF radio communication ................................................ 12

HI/LO transmission power ................................................ 17

Watch ............................................................................... 18

Scan ................................................................................. 19

Radio setup ...................................................................... 21

DSC calls ..........................................................................24

Phone book ...................................................................... 41

Loudhailer with talk-back .................................................44

Automatic foghorn ...........................................................45

Hailer and Fog horn setup ................................................47

Replay function ................................................................48

Chapter 3 Installation

Unpacking the SAILOR 6216 VHF DSC ................................49

Installing the VHF radio ....................................................50

Power, VHF antenna and external equipment ...................57

System setup ....................................................................64

SAILOR 6201 Handset cradle (optional) .............................65

ix

Table of Contents

Chapter 4 Service & maintenance

Contact for support .......................................................... 67

Maintenance ................................................................... 67

Equipment and accessories ..............................................74

Warranty ..........................................................................74

App. A Technical specifications

App. B Maritime channels

Glossary ........................................................................................ 83

Index ........................................................................................ 85

x

Chapter 111111

Intr

odu

ctio

n

Introduction 1

VHF radio with DSC

SAILOR 6216 VHF DSC, your

new SAILOR VHF radio with

full DSC functionality, is

approved to FCC and Industry

Canada and is waterproof to

the IPx8 and IPx6 standard.

As part of the required safety

equipment, use the SAILOR

6216 VHF DSC in an

emergency situation.

However the best way to

guarantee functionality in an

emergency situation, is to use the radio in daily communication on board.

The VHF radio is a simplex/semi duplex VHF radio. It is designed with an easy-

to-use menu-driven setup. You use the soft-keys to enter the desired

functions, you browse and select a setting using the right selection wheel

knob. The large display has red adjustable backlight which provides a good

visibility even at night and protects your night vision.

The VHF radio can replay the last 90 s of received voice. This is a useful

feature to minimize misunderstandings and to record messages when the

radio is unattended.

The VHF radio connects easily to external equipment like a 2-way loudhailer

and an external speaker. You can use the loudhailer as a 2-way on-board

communicator. The loudhailer also functions as a fog horn. You can select

from several programmed fog-horn patterns.

For a list of other accessories available for the SAILOR 6216 VHF DSC check

with your nearest distributor.

1

Chapter 1: Introduction

Controls on the front plate

1. Loudspeaker.

2. Four soft keys with function title in the display.

3. Quick selection key for channel 16 and the programmed call channel.

4. Large display.

5. Connector for Handmicrophone or handset. If not used, put the cap from

the ACC connector on the front connector to prevent water ingress.

6. Button for sending a DSC Distress alert.

7. Squelch control to mute background noise.

8. Replay button to play back up to 90 s voice message.

9. Volume wheel knob with key-press function for volume control and power

on/off.

10. Selector wheel knob with key-press function for changing the working

channel, navigating in menus in the display and backlight dimming.

21 3 4

65 7 9 108

2 VHF radio with DSC


11111

Intr

odu

ctio

n

SAILOR 6216 VHF DSC display

The picture shows the display

after start-up. The display holds

various fields of information,

depending on the currently

selected function.

1. Action line containing

information relevant for the

currently selected function.

2. Current working channel.

3. Functions you can select with the soft keys. If there are more than 4

functions in the list press the soft key MORE to display further functions.

4. Status and other values for the current state or VHF channel.

5. Service line containing current temporary information relevant for the

current channel or function.

For a detailed description of the information shown for each of the functions

available see the chapter Operation on page 5.

1 2

3 4

5

WATCH

CALL

US

DISTRESS/CALL16

GPS PositionHI/LO

MORE...

VHF radio with DSC 3


System configuration - example

HandsetMicrophone

AIS Receiver

GPS in (NMEA 0183)

CableService

Loud Hailer (4 ohm)Speaker (8 ohm)

External

AC

C. P

ort

Pow

er

Handset Option

SAILOR 6205SAILOR 6201

SAILOR 6201

99-129890-D

VHF DSC -

Hand MicrophoneSAILOR 6202

12V DC

110/220V AC

GPS

GPS,

Control Speaker

SAILOR 6207Connection Box

for parallel handsets

SAILOR 6217

CTR

L

AC

C

Chart Plotter

N163S

AerialRX/TX

SAILOR 6090

12V Battery

24V DC

Power Converter

4 VHF radio with DSC

Chapter 222222

Op

erat

ion

Operation 2

In this chapter you find detailed instructions and guidelines for:

• General use and navigation

• VHF radio communication

• HI/LO transmission power

• Watch

• Scan

• Radio setup

• DSC calls

• Phone book

• Loudhailer with talk-back

• Automatic foghorn

• Replay function

Note Before using the VHF radio make sure that the VHF antenna, power

and other external equipment are connected properly. For

instructions see chapter Installation on page 49.

5

Chapter 2: Operation

General use and navigation

Power on and speaker volume

The VHF radio has a dual-function on/off wheel knob for power

on/off and volume control.

• To power on the VHF radio press the on/off wheel knob.

• To power off the VHF radio, press and hold the on/off wheel

knob and follow the instructions in the display.

• To adjust the speaker volume, turn the volume wheel knob (clockwise =

louder, counter clockwise = softer, until muted). When adjusted to the

muted level is shown in the display.

Working channel, settings and dim function

The selector wheel knob has several functions:

• To select the working channel, turn the selector wheel knob.

• To browse and select settings, turn the selector wheel knob

and press for accept.

• To dim the backlight in the display until it is appropriate for the current

situation, i.e. to give comfortable night vision, press, hold and turn the

selector wheel knob (clockwise= more light).

6 General use and navigation


22222

Op

erat

ion

DSC and MMSI number

When the VHF radio is powered on for the first time, you must enter the

vessel’s MMSI number. Hereafter the MMSI number is briefly displayed after

power up. The MMSI is a unique, 9-digit identifier assigned to your ship.

Entering the MMSI number

When being prompted after power up enter the MMSI

number as described below:

1. Enter the 9 digits one by one by turning the

selector wheel knob to the desired digit, press the

selector wheel knob to accept the digit and

advance to the next digit.

To delete the previous digit press the soft key

BACK.

2. Press the soft key OK to confirm the entered MMSI number.

3. To leave without saving, press the soft key CANCEL.

Important The MMSI number must be programmed into the VHF radio to

use any DSC functionality. The radio will prompt for the MMSI

number at each power-up until the MMSI has been entered. An

error message is displayed when trying to initiate any DSC

function. However, you can use the radio in normal VHF mode.

Caution! Without a programmed MMSI number the

Distress button will not work!

Note The MMSI number can be programmed by the operator once. If a

wrong number has been entered and stored, or if there is a

requirement to change it, contact your authorized dealer.

General use and navigation 7


Once programmed, you can see the MMSI number

in the service line directly after start-up. The DSC

functionality is operational at any time.

The message NO DSC (NO MMSI) is shown in the

action line if the MMSI is not programmed.

Position and MMSI Information

To display position and MMSI information for the SAILOR 6216 VHF DSC radio,

do as follows:

1. Press the soft key POS. If it is not in the display, press the soft key MORE

until POS appears.

The display shows the current (latest) position (if a GPS is connected), the

UTC and position type, GPS Status and MMSI.

2. You can enter the position and UTC manually. Turn the selector wheel knob

to select the value you want to change. Then press and turn the selector

wheel knob to enter the current position or UTC time. The display shows

Man Position.

3. Press the soft key SAVE to save the new value.

4. After you have entered a value manually or overruled the GPS input, a soft

key UseGPS appears in the display if the GPS is available. Press this soft key

if you decide to use the data from the connected GPS.

5. Press the soft key EXIT to return to normal use.

If the GPS was present and then disappears a warning appears in the display

after 10 minutes. Follow the instructions on the screen.



22222

Op

erat

ion

Speaker devices

The VHF radio can be equipped with the following speaking devices:

• SAILOR 6202 Handmicrophone with a PTT (Push To Talk) button.

• Handset with a microphone, ear piece and a PTT button. The volume in the

ear piece can be adjusted, for details see Controller setup on page 10.

• Loudhailer.

• External speaker.

See Controller setup on page 10 for managing speaking devices.

Adjusting the squelch

With the Squelch control you can manually adjust and suppress

noise in order to optimize the quality of the received radio

communication.

• When hearing noise or an unwanted signal, turn the

squelch button clockwise until the speaker is muted.

Functions

The following functions are available from top-level standby:

Soft key Function

HI/LO Transmitter power, high or low

WATCH Dual or triple watch

CALL DSC calls

POS Current position from GPS, including UTC time and

MMSI number

ALERT Make a distress call, categories can be assigned



The functions of the SAILOR 6216

VHF DSC are accessed and set

using the four soft keys to the left

of the display. The current

function of a soft key is shown in

the display next to the soft key. For

some applications there are two control levels

• A top level showing the current information and options for this

application. This can be on one page, or on several pages.

• A setup screen showing the options you can configure for the specific

application.

Use the soft key MORE to display further applications.

Controller setup

In the CONTROLLER SETUP you set handset volume, external speakers and

display contrast. You can view the Software version and serial number.

To change a setting in the CONTROLLER SETUP, do as follows:

1. Press the soft key SETUP. If it is not in the display, press the soft key MORE

until SETUP appears.

2. Press the arrow soft key or to advance to CONTROLLER SETUP.

SCAN Scanning function

HAIL Loudhailer

FOG Fog horn

PHBOOK Phone book

SETUP Setup pages for RADIO, HAILER/FOG, SYSTEM,

CONTROLLER and DSC

Soft key Function

4 soft keys



22222

Op

erat

ion

3. Turn the selector wheel knob to go to a setting, then press

the selector wheel knob to change the setting.

4. Press EXIT to return to normal radio operation.

Parameter Description

Handset 1 vol: Adjust earpiece volume for handset 1: OFF, 1 to 14

Note: Default setting is OFF. If a handset is connected

to the front connector this value must be configured

to a value (1-14).

Handset 2 vol: Adjust earpiece volume for handset 2: OFF, 1 to 14

Note: Default setting is OFF. If a handset is connected

to the rear connector this value must be configured

to a value (1-14).

Ext. speaker FIX: Fixed level is set for external speaker

REL: Relative level following volume adjustment of

the internal speaker

Ext. fix/rel vol: External speaker fix or rel volume:

rel: -5 to 5. Offset relative to internal speaker steps

fix: OFF, 1 to 14

Language English

Contrast Display contrast, 1 to 5



VHF radio communication

In this section of the manual you find information on

• Basic VHF operation

• VHF channels

• Programming a call channel

• Naming a channel

Basic VHF operation

You can make VHF calls using the Handmicrophone or another speaking

device.

Quick guide to radio telephone calls

1. Press the PTT button on the speaking device. When the TX

indicator lights up in the display, the transmission is active.

2. To enable reception of a radio signal release the PTT button.

Note A single, short press on the 16/C key will always bring

you to channel 16, the international calling and distress

channel, no matter what menu the radio is in.

Note Press PTT only when you are talking. Always say “Over.” just before

releasing the PTT button.

Note One transmission is limited to 5 minutes duration.

12 VHF radio communication


22222

Op

erat

ion

Receiving a radio telephone call on channel 16

When you hear your call name in the loudspeaker,

proceed as follows:

1. An RX symbol shows that the radio is receiving on

the channel displayed.

2. Lift the Handmicrophone or take the handset.

3. Press the PTT key. A TX symbol shows that the

radio is transmitting on the channel displayed.

4. Repeat the name of the station calling you and

say: “This is [your ship’s name]”.

5. Suggest a working channel other than 16 by

saying: “Channel [suggested channel number]”.

6. Say: “Over.” and release the PTT key to allow the caller to confirm the

suggested new channel.

7. Switch to the new channel by turning the selector wheel knob to

the agreed channel and begin your conversation. Press PTT only

when you are talking.

Making a radio telephone call on channel 16

To make a radio telephone call, proceed as follows:

1. Select channel 16 by pressing the soft key 16/C or by turning the

selector wheel knob.

2. Lift the handset or take the Handmicrophone.

3. Press the PTT key. A TX symbol shows that the

VHF radio is transmitting on the working channel

displayed.

4. Say the name of the station you are calling three

times.

5. Say: “This is [your ship’s name]”.

VHF radio communication 13


6. Say: “Over.” and release the PTT key to listen. An

RX symbol shows that the radio is receiving on the

working channel displayed

7. When answered, agree upon a working channel

other than 16.

8. Switch to the new channel by turning the selector

wheel knob to the agreed channel and begin your

conversation.

VHF channels

You can change channels whenever the channel

designator is displayed. Turn the selector wheel knob to

browse through all channels that are available in the

selected channel mode. The channels appear in the

display in the following order:

• Primary channels

• Weather channels (if any)

• Private channels (if any)

To quickly toggle between these 3 channel groups make

a long press and release the selector wheel knob. The

VHF radio toggles between the last selected channels in

the respective groups, i.e. the last selected weather

channel, the last selected private channel or the last selected primary channel.

If there are no channels defined in a group, none will be selected.

VHF channel table Description

Primary channels

(no prefix)

For details see Maritime channels on page 79.

For instructions how to change a channel table see Radio

setup on page 21.

Weather (WX) Weather channels have the prefix W. (For US and CA

channels only.)



22222

Op

erat

ion

Programming a call channel

To program a call channel (or quick selection), do as follows:

1. Make an extra-long press (2.5 s duration) on the 16/C key.

2. Press the soft key CALL CH. The channel designator is flashing.

3. Turn the selector wheel knob to select the desired channel.

4. Press the soft key OK to confirm the new call channel and leave

edit mode.

Naming a channel

To name a channel, do as follows:

1. Make an extra long press on the 16/C key until NAME is shown

in the display next to one of the soft keys.

2. Turn the selector wheel knob to select the channel you want to name.

3. Press the soft key NAME.

4. Turn and press the selector wheel knob to enter the name, letter

by letter. Press BACK to move one character to the left. Press

CLEAR to the delete the current character and the following

characters. A long press on CLEAR deletes all characters.

5. Press the soft key OK to confirm the entered value

and to leave edit mode.

6. Press EXIT to return to return to the standard VHF

display.

Private (PRIV) Up to 40 user-defined private channels. Contact your dealer

for programming private channels.

VHF channel table Description

VHF radio communication 15


Display for non-VHF applications

When the radio is used for functions other than VHF, the display is arranged

differently. The large channel display moves to the bottom line along with

selected icons.

The channel displayed in this line will always reflect the communication

channel on which the radio is tuned into for communication.

If PTT is pressed the radio transmits on the displayed channel (not valid for

hailer mode).

If a signal is received the signal is received on the displayed channel.

Engagement status

The radio is considered engaged when an active DSC-initiated communication

is ongoing, or communication is active on non-DSC initiated VHF operation:

• A new channel selected

• PTT pressed or,

• Voice signal received

The engagement state is used to prohibit incoming DSC calls from taking over

control of the transmitter channel, disrupting ongoing communication.

When the radio is engaged in VHF communication not initiated by DSC, this is

indicated with the icon in the lower right position of the display.

Engagement will automatically time-out on inactivity (in the absence of any of

the listed events above), and after an inactivity time specified in DSC setup,

Comm Inactivity on page 39.

To terminate the engagement immediately press the soft key .

Before the automatic disengagement, the icon will flash. To prolong the

engagement press the soft key .



22222

Op

erat

ion

HI/LO transmission power

Press the soft key HI/LO to toggle the transmit power between low (1 W) and

high (25 W). If LO is not displayed, the transmit power is HI.

US channels: Local mode, 10 dB attenuation

To attenuate to the incoming signal, do as follows:

1. Press the soft key LOCAL to add 10 dB attenuation. If it is not in the display,

press the soft key MORE until LOCAL appears in the display.

US channels: Overriding LOW power for channels 13 and 67

When running in US mode you can override low power on the alternative call

channels 13 and 67. Do as follows:

1. With the VHF radio set to 13 and 67, press PTT on the speaking device.

2. Press the soft key OVRIDE to transmit with full power.

When you release the PTT button, the transmission power goes back to

low.

Note Local mode is automatically exited when using channel 16. If you

want to use attenuation on channel 16 or a call channel, you must

set it manually each time.

HI/LO transmission power 17


Watch

The SAILOR 6216 VHF DSC radio

can be set to dual watch or triple

watch. In dual watch, the

working channel and channel 16

are watched. In triple watch the

working channel, channel 16

and the programmed call

channel are watched.

You can select the working

channel in any watch mode by

turning the selector wheel knob.

The working channel that is displayed is the channel used for dual or triple

watch. If there is a signal in one of the watched channels and squelch opens,

the display shows the channel in which the signal is received.

Using WATCH

1. To start watch press the soft key WATCH. The radio

enters the last watch mode. It is displayed in the

action line.

2. To stop WATCH press WATCH again, or press PTT

on the speaking device.

For instructions how to change between DUAL and TRIPLE WATCH see Radio

setup on page 21.

Note If PTT is operated during any watch mode. the WATCH function is

terminated and you transmit on the displayed channel. Watch mode

may be resumed after releasing the PTT button if the scan resume

time is set up in SETUP, for instructions see Radio setup on page 21.

18 Watch


22222

Op

erat

ion

Scan

The radio has a scanning function for tagged channels. Any available channel,

including weather and private channels, can be tagged and added to the

scanning sequence. As default the radio scans with priority scanning of

channel 16. If a signal is received while in any scanning mode, only channel 16

continues to be watched.

If there is a signal in one of the scanned channels, the display shows the

channel in which the signal is received. Pressing PTT while a signal is received

stops scanning and the radio is tuned into the displayed channel.

Using SCAN

1. To start scanning press the soft key SCAN. The SCAN menu is shown. Press

START to start scanning.

2. To stop SCAN press SC STOP, or press PTT on the

speaking device.

3. To tag a channel in order to include it in the

scanning sequence, turn the selector wheel

knob until the wanted channel is in the display.

Then press the soft key TAG. The display shows

the channel number and the word TAG at the right side of the display.

4. To remove a channel from the scanning sequence, turn the selector wheel

knob until the tagged channel is displayed. Then press the soft key TAG to

remove the tag.

When scanning is activated the working channel is displayed in a different

format (open, outline typeface). This indicates the radio is not tuned into the

displayed channel. The displayed working channel is temporarily included in

the scanning list (although no TAG icon is shown).

If PTT is pressed while scanning, the scanning is stopped and transmission

starts immediately on the displayed working channel.

Scan 19


US channels: Watch alarms for NOAA Weather alerts

You can turn on or off an independent watch alarm for a specific weather

channel.

To turn on or off an independent NOAA weather alarm do as follows:

1. In the SCAN menu, turn the selector wheel knob to

select a specific weather channel.

2. Press the soft key WX to tag this weather channel

for NOAA weather alert.

3. On the display you can see that the selected

weather channel alert watch is enabled. In this example it is [W2].

The weather channel set-up for the alarm is scanned frequently during

scanning, watch or when the radio is not operated or receiving on a

working channel.

4. If a NOAA weather alert is detected on a weather

channel, beep tones are presented and a pop-up

window is displayed. Press YES to switch to the

weather channel.

Note NOAA weather channels are available in the waters of USA and

Canada only.

20 Scan


22222

Op

erat

ion

Radio setup

In the RADIO SETUP you set scan and watch mode, select the channel table

and can set and view the ATIS code. To change a setting in the RADIO SETUP,

do as follows:



2. Press the arrow soft key or to advance to RADIO SETUP.




Para-

meterDescription

Scan

Hang

Time

Scan hang time, in seconds on an active receiving working channel.

The time is measured from the signal is detected. The radio remains

on the channel for the set time interval, if a signal was detected.

OFF: Resumes scanning when signal disappears (default)

4, 6, 8, 10: Hang time in seconds.

Scan/

watch

Resume

Scan resume time, in seconds. When the programmed time of

inactivity has elapsed, and when watch/scan has been aborted using

a press on PTT, or after power-up, scan or watch is resumed.

OFF: Automatic resume is deactivated (default)

3, 6, 10, 15, 20, 25, 30: Resume time in seconds.

Watch

Mode

DUAL: Dual watch monitoring the working channel and the priority

channel (channel 16, default for international channels).

TRIPLE: Triple watch. The working channel is watched with the

priority channel (channel 16) and the programmed call channel (if

any, otherwise dual watch).

Radio setup 21


Priority

Scan

ON: All channels tagged for scanning are scanned while monitoring

channel 16. (default).

OFF: Only the channels tagged for scanning are scanned in sequence,

not channel 16, unless it is tagged for scanning.

Channel

Mode

To select the channel table for the primary channel. Channel tables

available: US, CAN, ALT, PRIV, See also VHF channel table on page 14.

Band-

width

Selection of the bandwidth for the fixed pre-programmed channels.

This is recommended from Radio Regulations:

Wide: Wide band is 25kHz channel bandwidth (default)

Narrow: Narrow band defines a channel bandwidth of 12.5kHz

Para-

meterDescription

22 Radio setup


22222

Op

erat

ion

ATIS

code

The ATIS code (Automatic Transmitter Identification System) is used

for identification to marine coast and inland stations and its use is

mandatory in a number of European inland waterways such as e.g.

the river Rhine.

Like the MMSI number the ATIS number is issued by the relevant

authority.

Enter the format of the programmed ATIS code according to the

following call sign prefix conversion table:

Note: The ATIS number can be programmed by the operator once. If a

wrong number has been entered and stored, or if there is a

requirement to change it, contact your authorized dealer.

Para-

meterDescription

Character Phonetic Value Character Phonetic ValueA Alpha 1 N November 14B Bravo 2 O Oskar 15C Charlie 3 P Papa 16D Delta 4 Q Quebec 17E Echo 5 R Romeo 18F Foxtrot 6 S Sierra 19G Golf 7 T Tango 20H Hotel 8 U Uniform 21I India 9 V Victor 22J Juliett 10 W Whiskey 23K Kilo 11 X X-ray 24L Lima 12 Y Yankee 25M Mike 13 Z Zulu 26

Radio setup 23


DSC calls

In this section of the manual you find information on:

• Sending, acknowledging and cancelling own distress

• Receiving distress calls

• DSC calls for communication

• DSC setup

Sending, acknowledging and cancelling own distress

To send a distress message

To send a distress message do as follows:

1. Lift the cover over the red distress button and press and hold

the distress button for longer than 3 seconds. For short step-

by-step instructions how to proceed when sending a distress

message see Emergency calls on page iv.

When the distress signal is sent, CH70 and Tx

appear in the display. A 2-seconds beep tone is

heard.

2. The radio watches for a DSC acknowledgement

tansmission on channel 70.

3. To pause the automatic resend procedure press

the soft key PAUSE.

4. To annul the distress message press the soft key ANNUL. See also To cancel

own distress on page 27.

5. When a distress acknowledgement is received, start distress

communication on channel 16 to inform about your distress situation.

Note If no distress acknowledgement is received within a period of 3,5 to 4

minutes, the distress message will automatically be retransmitted.

(Example)

24 DSC calls


22222

Op

erat

ion

Having pressed the red distress button and sent the

distress message, press the soft key INFO to display

further information:

• STATION: shows the radio’s MMSI number.

• NAT: shows the nature of distress, see also To

send a distress message with specified nature on

page 25.

• LAT:, LON:, POS UTC: shows the distress position data as transmitted.

• MODE: shows the communication mode.

If you sent a distress message, the VHF radio is automatically set to channel

16, the channel reserved for international distress, safety and calling.

To send a distress message with specified nature

When sending distress messages you can include the distress nature in the

message. To include the distress nature in the distress message do as follows:

1. From top-level standby press the soft key ALERT.

If it is not in the display, press the soft key MORE

until ALERT appears.

2. Press the selector wheel knob, then turn it to

select among the supported natures of distress:

(Example)

FIRE, EXPLOSION DISABLED (and adrift)

FLOODING UNDESIGNATED

COLLISION ABANDONING (ship)

GROUNDING PIRACY (/armed robbery attack)

LISTING (in danger of capsizing) MAN OVERBOARD

SINKING

DSC calls 25


3. Press the selector wheel knob to accept the selected nature of distress.

4. Then lift the cover of the red distress button and push the

Distress button for 3 seconds.

To acknowledge own distress

When the SAILOR 6216 VHF DSC receives an

acknowledgement of distress from another vessel or

station, a 2-tone alarm sounds. The display shows

the MMSI number of the station who sent the

distress acknowledgement call, the status and the

time passed since the distress acknowledgement

arrived (format: mm:ss).

• Press SILENT to only switch off the 2-tone alarm. A press on any other key

also switches off the 2-tone alarm.

• Press the soft key INFO to display further data for this call.

• Press the soft key OK to view the status of this

distress call.

If the same Distress call comes in more than once,

the 2-tone alarm sounds briefly and terminates

automatically.

26 DSC calls


22222

Op

erat

ion

To cancel own distress

If you need to cancel a sent distress message do as

follows:

1. The display shows that a distress message has

been sent. Press the soft key ANNUL.

2. Press the soft key YES to go ahead with the

cancelling process. At this stage you have the

option to press the soft key NO to return to distress

sending procedure.

3. The SAILOR 6216 VHF DSC will send the Self-

cancellation call on channel 70 and the display

automatically shows the message that you should

say when cancelling the distress with a radio

message.

4. Press the soft key INFO to scroll to the next display

to proceed with the voice cancel

5. Press the soft key OK to go to the acknowledged

state. Own distress is cancelled now.

DSC calls 27


Power failure while in distress

In case of a power failure or switch-off during the

transmission of a Distress the SAILOR 6216 VHF DSC

gives an audible warning after power-up and

automatically resumes sending Distress 10 seconds

after power up.

Within the 10 seconds you have the following options:

• Press QUIT to terminate the active distress procedure (acknowledged or

unacknowledged)

• Press CONFIRM (or do nothing) to resume the sending Distress procedure.

Receiving distress calls

When the radio receives a distress call, the 2-tone alarm sounds.

Types of distress calls are DISTRESS, DISTRESS ACK,

DISTRESS RELAY and DISTR. RELAY ACK.

1. To switch off the 2-tone alarm press the soft key

SILENT. A press on any other key also switches off

the 2-tone alarm.

2. If you decide to stay in the communication loop to

receive follow up information, updates etc., press

the soft key OK.

3. If you don’t accept the distress call, press the soft

key CANCEL, then the radio logs the call.

4. Monitor channel 16 as a coast station may require

your assistance. If the radio is not on channel 16, turn the

selector wheel knob or use the key 16/C to go to channel 16.

5. The radio receives the first distress acknowledgement call and

the 2-tone alarm sounds again. To switch off the 2-tone alarm press the

soft key SILENT. A press on any other key also switches off the 2-tone

alarm.any key.

28 DSC calls


22222

Op

erat

ion

Distress call with errors

If a distress call contains errors, it is still received

and errors in the data are shown as underscores

(_).

Distress call log

As long as you are part of a distress session, i.e. you

have not pressed QUIT, you receive distress messages

and can track all distress messages for the current

distress event.

Do as follows:

1. Press the soft key LOG. If it is not in the display, press the soft key MORE

until LOG appears.

2. Press the soft key NEXT and PREV to browse the received Distress

messages.

3. Press the soft key EXIT to leave the log.

DSC calls 29


DSC calls for communication

With a DSC call you can establish a radio communication with one or several

specific radios on a suggested VHF channel.

To make a DSC call for communication, do as follows:

1. Press the soft key CALL.

The default call is an individual routine call. Press

and turn the selector wheel knob to enter the 9-

digit MMSI number of the vessel you want to

contact or use the phone book to select a frequently called contact.

The soft key is used to toggle between the VHF communication and a

DSC session on hold.

2. Press and turn the selector wheel knob to select other call types or set the

details for the call:

• Type:

DSC call type Category

INDIVIDUAL

(default)

Routine (default) or safety calls, calls to a ship

or a station

GROUP Routine

ALL SHIPS Safety (default) or urgency

SAFETY TEST Test call, check of safety equipment

POSITION Routine position request

30 DSC calls


22222

Op

erat

ion

• Press and turn the selector wheel knob to change the suggested VHF

channel for following communication.

3. Press the soft key SEND to make the call.

Sessions

A DSC session (or automated procedure) is defined as a collection of DSC calls

(transmitted and/or received) that are related to the same event (e.g. a

distress event) or established call (e.g. an individual call request followed by

an acknowledgement).

A session can be either active or on hold. The active session has control over

the radio transmitter.

A session can have a purpose. For example if the purpose is to establish a

communication on a working channel.

The non-DSC VHF communication is considered as a session that can be active

(engaged) or on hold (dis-engaged). See also Engagement status on page 16.

Display for a DSC session

1. Head line showing the type of call that

initiated the DSC session, see table

below for a list of available head lines.

2. Session status line displays the current

state of the session:

• WAIT FOR ACKNOWLEDGE – You

made an individual call to a station and are awaiting a reply to

establish connection.

• OCCUPIED - The DSC transmission mechanism waits until the DSC

channel (70) is free.

• TRANSMITTING - Transmission of a DSC message is ongoing.

• IN COMMUNICATION WITH – The communication has been established.

3. The MMSI number of the other party, if contact to a specific station or

group shall be established.

DSC calls 31


4. Elapsed time since the reception of a call request or an acknowledgement.

5. Session state:

• (ACTIVE) — transmitter tuned into the communication channel.

• (HOLD) — parked session.

6. Channel used for following communication (if any) when the session is

active.

Headline Explanation

OWN DISTRESS The ship is in own distress. See also To send a

distress message on page 24.

DISTRESS RX You watch or participate in a distress communication

for another station in distress

RELAY calls

(numerous)

You watch or participate in a distress communication

for another station in distress

ALL SHIPS TX/RX You have sent / received an all ships call

GROUP TX/RX You have sent / received a group call

INDIVIDUAL

TX/RX

You have either sent a call request to a station to

establish contact, or another station has made a call

to you to establish contact. The call needs a reply.

TEST TX/RX You either have sent a SAFETY TEST call or have

received a SAFETY TEST call from another station that

needs to be replied.

POSITION TX/RX A position request was either sent or received.

32 DSC calls


22222

Op

erat

ion

Soft keys to control DSC sessions

Call/session types vary in control options, and options may also change if a

session changes its state. The following table gives an overview of the DSC soft

key commands available:

Soft key Radio function

QUIT Terminates the DSC session

HOLD Puts the DSC session hold if it is active (return to other

non-DSC functions)

ACTIVE Activates the DSC session

INFO Shows details about the DSC call

RESEND Transmits an identical call if available

NEWCHReplies with a new channel if an individual call is

received with a communication channel specified

which is not available in the radio, or the operator

decides to change the channel.

UNABLEConstructs a reply to the caller if an individual call is

received which is not compatible with the radio modes.

SILENTSilences alarms. Any key silences the alarm but this

soft key function will do only this.

ACK Acknowledges a received call request with the

suggested parameters.

POS (Own

Distress)

A shortcut to own position data information.

PAUSE (Own

Distress)

Pauses the automatic repetition of distress

transmissions

RESUME (Own

Distress)

Resumes automatic repetition of distress

transmissions (if paused)

DSC calls 33


See also Handling a background session on page 37.

ANNUL

(Cancel Own

Distress)

Cancels an inadvertently transmitted distress

CONFIRM

(Cancel Own

Distress)

Confirms action and proceed sequence, used in cancel

distress procedure

INFO (in

Cancel Own

Distress)

Turns page of text message.

LOG (Received

distress)

A filtered version of the log displaying received calls

relevant to the current distress event.


34 DSC calls


22222

Op

erat

ion

Detail information for DSC sessions (soft key: INFO)

A DSC session is updated based on DSC calls received or transmitted. Press the

soft key INFO to show the details for the current session.

For distress events a sequence of calls may contribute to the complete view

and status of the session. Detailed fields for distress are:

For other session types the soft key function INFO typically shows the details

from a single call. Detail fields for other calls than distress are:

Details — Distress Explanation

DISTR-MMSI The vessel in distress

NAT Nature of Distress

LAT Latitude position of station in distress

LON Longitude position of station in distress

POS UTC Time of position

MODE Communication mode (Simplex/Semi-duplex

Telephony supported)

Details —other calls Explanation

CALL Type (on received call) – The call type may be shown on

call reception

CAT Category of the call: Urgency, Safety or Routine

FROM The initiator of the call

TO The intended receiver of the call (unless All Ships)

MODE Communication mode (Simplex/Semi-duplex

Telephony supported)

CHANNEL Subsequent communication channel

LAT Latitude position returned upon a position request

DSC calls 35


Receiving DSC calls

If the radio is IDLE (not engaged in another session) and a DSC call is received

the call details are shown on the display. The following options (soft keys) are

available:

If the radio is engaged while receiving a DSC call, the call is shown if it was of

higher priority (importance for safety or life). Otherwise it is just queued in the

DSC call log for later handling (marked as unread).

If the call is displayed the following soft keys appear:

An envelope symbol is shown whenever there are unread messages in

the DSC log. Unread messages are automatically retrieved from the log as

LON Longitude position of station in distress

POS UTC Time of position

Details —other calls Explanation


ACK

(individual)

The call is acknowledged immediately and the radio is

afterwards tuned to the communication channel (if any

suggested)

OK (group

or all ships)

The radio is already tuned to the suggested communication

channel (if any suggested). Pressing this button will display

the DSC session view.


ACCEPT If you accept the new incoming call the radio terminates the

ongoing session and the session view is initiated for the

new call.

LOG The call is logged in the DSC call log as an unread message.

36 DSC calls


22222

Op

erat

ion

soon the current DSC session is terminated. The call with the highest priority

(importance for safety or life) is shown first.

Handling a background session

The equipment is designed with the possibility to control a DSC session

simultaneously with a VHF communication session. The sessions can keep

track of their session state and the communication channel used.

If a DSC session is put on HOLD it is automatically put in the background (VHF

communication display appears on the previous communication channel).

The soft key is used to toggle between the VHF communication and a DSC

session on hold.

The DSC session on hold can receive calls that are pertinent to the session,

even when the session is not displayed. If the background receives updates

the icon is shown.

Example: An individual call request has been

sent. While waiting for the

acknowledgement of the call,

communication is engaged on VHF

(press the soft key HOLD on the DSC

session view). The

acknowledgement is received from

the called station (the icon is

shown). Press the soft key and ACTIVE to engage in the DSC

initiated communication.

DSC calls 37


DSC call logs

To display a DSC call log in the DSC CALL LOGS, do as follows:



2. Press the arrow soft key or to advance to DSC CALL LOGS.


the selector wheel knob to view a log.

Use the soft keys NEXT and PREV to leaf through all logs.


DSC setup

To change a setting in the DSC SETUP, do as follows:



2. Press the arrow soft key or to advance to DSC SETUP.



DSC call log Description

Received Distress Shows a log of up to 20 received distress calls.

Transmitted Calls Shows a log of up to 20 transmitted calls.

Received Calls Shows a log of all received non distress calls.

38 DSC calls


22222

Op

erat

ion


DSC setting Description

Position Info Available position information.

Here you can enter position data, see also Position

and MMSI Information on page 8.

Auto-Ack Test Auto-acknowledgement of test DSC messages

OFF - Disabled

ON – Enabled (default)

Auto-Ack Individual Auto acknowledgement of individually addressed,

non distress DSC messages

OFF - Disabled (default)

ON – Enabled

Non-Distr. Inactivity Inactivity time-out to exit non-distress functions

(e.g. in setup) without automatic time-out (OFF):

Range: OFF, 1 to 30 minutes, in 1 min. steps

Default: 15 min.

Distress Inactivity Inactivity time-out for received distress DSC

automated procedures without automatic time-

out:

Range: OFF, 1 to 30 minutes, in 1 min. steps

Default: OFF

Comm Inactivity Inactivity time-out of non DSC communication

(VHF).

Range: 10 to 600 seconds, in 10 s steps

Default: 30 s

Non-Distr.Alarms Non-distress DSC alarms

OFF: Disabled

ON: Enabled (default)

DSC calls 39


Auto-switch

Channel

Enable automatic channel switching on reception

of DSC calls with subsequent communication

channel information, while the radio is not

engaged (for calls other than individual station

calls of category distress or urgency).

ON (default)

OFF - LCK icon indicates that the channel is locked

and must be selected manually

DSC Self Test You can set the radio to run a DSC self test.

OFF: Disabled (default)

RUN: Run test.

For further details about this test see DSC routine

testing on page 70.

DSC setting Description

40 DSC calls


22222

Op

erat

ion

Phone book

Use the phone book when making a DSC call. You can enter up to 50 contacts.

A contact has the following details:

• Name (up to 20 characters)

• Type (SHIP, GROUP or COAST STATION)

• MMSI number

• Channel

• Position Auto Acknowledge (yes or no) or Listen to Group

The phone book is always sorted alphabetically by contact names. Use the soft

key FILTER to toggle between CONTACTS - ALL, COAST, SHIP or GROUP. After

having selected a contact, the phone book closes automatically.

Using the phone book to make a DSC call

To call a contact using the phone book do as follows:

1. Press the soft key CALL. If it is not in the display, press the soft key MORE

until CALL appears. The DSC call composer is shown in the display.

2. Press the soft key PHBOOK.

3. Turn the selector wheel knob to scroll to the phone book entry that you

want to call.

4. Press the selector wheel knob to select the contact.

5. Press the soft key SEND to make the call.

Phone book 41


Adding a contact to the phone book

To add a contact to the phone book do as follows:

1. Press the soft key PHBOOK. If it is not in the display, press the soft key

MORE until PHBOOK appears in the display.

2. Press the soft key ADD.

3. Press the selector wheel knob to enter the <Name> field.

Enter the name by turning the selector wheel knob to the desired letter,

press the selector wheel knob to accept the letter and advance to the next

letter. To finish press the soft key OK.

4. Press and turn the selector wheel know to select the Type: SHIP, GROUP or

COAST STATION.

5. MMSI: Turn and press the selector wheel knob to enter the contact’s MMSI

number (9 digits), press the soft key OK to accept.

6. CHAN (optional): Press and turn the selector wheel knob to select the

preferred channel for this contact, press the soft key OK.

7. Position Auto Ack (for Type SHIP or COAST STATION): Press and turn the

selector wheel knob to select YES or NO for this contact, press the soft key

OK. This will allow auto-ack of position requests for this contact.

or:

Listen to Group (for Type GROUP): Press and turn the selector wheel knob

to select YES or NO for this contact, press the soft key OK. The radio will

respond to calls to the specified group.

8. Press the soft key SAVE to save the contact information.

9. Press EXIT to leave the phone book and return to VHF operation.

42 Phone book


22222

Op

erat

ion

Editing a contact


MORE until PHBOOK appears.

2. Press the soft key EDIT.

3. Press and turn the selector wheel knob to browse through the details of the

contact.

4. Continue as described in Adding a contact to the phone book from step 2

onwards.

Deleting a contact


MORE until PHBOOK appears.

2. Turn the selector wheel knob to browse to the contact you want to delete.

3. Press the soft key MORE until DELETE appears.

4. Press the soft key DELETE.

5. Press EXIT to leave the phone book and return to VHF operation.

Phone book 43


Loudhailer with talk-back

The SAILOR 6216 VHF DSC supports a loudhailer with a talk-back function.

To activate the loudhailer do as follows:

1. Press the soft key HAIL. If it is not in the display, press the

soft key MORE until HAIL appears.

2. Press PTT on the speaking device to activate the HAILER.

3. To change the receiving radio channel, turn the selector

wheel knob.

4. To adjust the HAIL volume press the PTT button and turn the volume knob.

5. Press the soft key EXIT to leave the hailer function.

Using the hailer with talk-back

While in hailer mode the hailer can also be used as a

microphone. For details how to set the talk-back mode see

Hailer and Fog horn setup on page 47. Once set up talk-back is

activated when you are in hailer mode and the PTT button is released.

When talk-back is active your crew can talk to you via the loudhailer horn unit

into the loudspeakers. The talk-back volume can be independently adjusted

on the volume knob while talk-back is active (TB Volume). If a signal is

received on the radio while in talk-back mode, the received radio signal will

be heard in the speakers. The received radio signal will be reproduced with

the normal volume level.

Important When the hailer is in talk-back mode and a radio signal is

received, the radio signal has a higher priority and is heard in

the loudspeaker.

44 Loudhailer with talk-back


22222

Op

erat

ion

Automatic foghorn

The SAILOR 6216 VHF DSC has an automatic fog horn application with several

foghorn patterns. Once started, it runs in the background while running any

other application. The fog horn may be combined with the loudhailer talk-

back mode. When the fog horn is activated, the text FOG is shown in the top

right corner of the display.

The "TB" symbol is shown in the display if Foghorn talk-back is selected and

the automatic foghorn is activated.

The foghorn patterns are fixed and sent out as whistle blasts or as a bell

pattern. The tone frequency can be set in the foghorn setup menu.

To activate the foghorn do as follows:

1. Press the soft key FOG. If it is not in the display,

press the soft key MORE until FOG appears.

Important Loudhailer talk-back may be active between foghorn

emissions. See Hailer and Fog horn setup on page 47.

Automatic foghorn 45


2. Use the selector wheel knob to browse through the patterns available.

3. Press the selector wheel knob at the wanted pattern to accept the pattern.

4. To deactivate the foghorn, turn the selector wheel knob to browse to OFF

and press the selector wheel knob.

Foghorn test tone

To manually control that the foghorn produces a blast tone, do

as follows:

The HORN key appears when no active fog pattern is

emitted (OFF). Press and hold the soft key HORN to activate

the blast tone and adjust the volume of the foghorn by

turning the volume wheel knob.

46 Automatic foghorn


22222

Op

erat

ion

Hailer and Fog horn setup

To change a setting in the HAILER/FOGHORN SETUP, do as follows:



2. Press the arrow soft key or to advance to HAILER/FOGHORN SETUP.




Parameter Settings

Hailer

Talk-back

OFF - Talk back is disabled (Default).

ON - Talk back is enabled when listening in the hailer PA

mode.

Foghorn

Talk-back

OFF - Talk back is disabled if the periodic foghorn is

activated.(Default)

ON - Talk back is enabled if the periodic foghorn is activated,

talk back between horn emissions.

Foghorn

Freq.

Adjust the foghorn frequency, allowed range: 200-850 Hz.

Hailer and Fog horn setup 47


Replay function

Replay allows the operator to playback received voice messages in the

loudspeaker.

Recording is activated automatically when a signal is received. Recording is

not possible during playback. Up to 60 tracks or 90 seconds can be handled.

The recorded channel is displayed. The message length is shown in seconds.

The display shows how old the message is. If the 90 s storage limit is reached,

the oldest data is overwritten.

Replaying recorded messages

To replay a message do as follows:

1. Press the Replay button (short press). The latest message

(message) is repeated. Information about this message is

shown in the display.

2. To stop replaying the message press the soft key STOP.

3. To play the current message again from the start press the Replay button

(short press).

4. To track back the series of messages double-press the Replay button (short

press) until the desired track is shown. The selected track is played.

5. To track back in time press and hold the Replay button until the desired

point in time. All messages up to the newest will be played.

48 Replay function

Chapter 333333

Inst

alla

tion

Installation 3

In this chapter you find information and guidelines for:

• Unpacking the SAILOR 6216 VHF DSC

• Installing the VHF radio

• Power, VHF antenna and external equipment

Unpacking the SAILOR 6216 VHF DSC

The following items are included in the delivery of a SAILOR 6216 VHF DSC:

• SAILOR 6216 VHF DSC

• SAILOR 6202 Handmicrophone with spiral cable

• User and installation manual (this manual)

• Installation guide

• Mounting bracket with two wheel knobs

• Connectors for cables

• Power cables, fittings and fuses

• Packaging material

• Sun screen (click-on) for front plate protection

• Kit for flush mount installation, including gasket

49

Chapter 3: Installation

Installing the VHF radio

You can mount the VHF radio as a desktop, overhead or flush-mounted unit

integrated in the instrument panel.

Provide space enough to access the front panel connectors and for installing a

cradle for the speaking device.

Provide at least 120 mm space at the back of the SAILOR 6216 VHF DSC radio to

allow free air circulation.

Compass safe distance

Make sure that the VHF radio is far enough from any magnetic compass to

avoid influence of the loudspeaker magnet on the compass reading. See the

following table for the safe distance after magnetization between the nearest

point of the device and the centre of the compass at which it will produce a

deviation of 0.3°.

Device Safe distance

SAILOR 6216 VHF DSC 1.0 m

SAILOR 6202 Handmicrophone 0.8 m

SAILOR 6209 Accessory Connection Box (optional) 0.6 m

50 Installing the VHF radio


33333

Inst

alla

tion

SAILOR 6216 VHF DSC with U mounting bracket

The mounting bracket and two knobs are included in the delivery.

Desktop mounting

Installing the VHF radio 51


Overhead mounting



33333

Inst

alla

tion

Mounting with U mounting bracket

To mount the VHF radio

as tabletop, do as

follows:

1. Find a suitable

location for the VHF

radio. Check that the

space is wide/deep

enough to

accommodate the

VHF radio.

2. Fasten the bracket

with 4 screws

(included in the

delivery.)

3. Insert the VHF radio

in the bracket and

fasten it with the two

knobs.

4. The display of the

VHF radio should be

at an angle of

approximately 90° to

your line of sight

when operating it.

99-130249

4 x M4 or hole forself-tapping ø3.9

150mm

53mm

71mm

196mm

23mm

9mm



SAILOR 6216 VHF DSC for flush mount

You can mount the VHF radio to a flat surface, e.g. an instrument panel. The

flush mount installation kit is included in the delivery.

Important The scaling in the above drawing is not 1:1. Consequently do

not attempt to use a print or copy of this page without checking

the dimensions.

Remove material from shaded area only!

89mm

177mm

R2.5mm x 4



33333

Inst

alla

tion

99-1302

Gas

1. Find a suitable location for the VHF radio. Check that the space is deep

enough to accommodate the VHF radio and an additional min. 120 mm

space for cable entry.

2. Keep free distance to allow free air circulation around the VHF radio and to

allow sufficient space for access to cables, see the drawing on this page.

3. Cut out the hole for the VHF radio where you want to mount it. Use the

cutting template in the installation guide.

4. Mount the 4 square nuts M4 in the cabinet, ensure that they are placed

correctly so it is possible to screw in the M4x45 screws.

5. Ensure that the flush mount gasket is placed correctly on the VHF radio.

6. Before mounting the VHF radio be aware that the surface is plane and

rigid. If the surface is not plane and/or rigid (stiff) remove the gasket and

seal with silicone sealant between the VHF radio and the surface.

7. Slide the VHF radio in the cut-out. Place the flush mount bracket and fasten

it with the 4 screws M4x45. Make sure the torque does not exceed 1Nm

when fastening the screws.

.

Note Only use screws supplied with the kit for flush mounting.

A AB B

48

ket Flush Mount Bracket (2 pcs.)

Screw M4x45 TORX 20 (4 pcs.)

Connect to LOUD HAILER(RED isolation on inner connector)

Connect to EXT. SPEAKER(WHITE isolation on inner connector)

Connect to POWER +(RED wire)

Connect to POWER -(BLUE wire)

Square Nut M4x7x2.2 (4 pcs.)

Max wall thickness 26mm

Note Firmly tie back and secure any wires not used to avoid the possibility

for mutual shorting or shorting to ground.



SAILOR 6202 Handmicrophone

Handmicrophone with spiral cable and PTT button.



33333

Inst

alla

tion

Power, VHF antenna and external equipment

1. ACC connector for

accessories

2. CTRL connector

for control

speaker

microphone

3. Power,

Loudhailer,

foghorn and

external speaker

4. VHF antenna

5. Ground stud

ACC connector

Use the connector marked ACC to connect GPS input.

The interface for GPS is NMEA 0183 (EN61 162-1 NMEA0183/ EN61 162-2

NMEA0183 Highspeed).

Connector type: Circular connector, 10pin.

Connection cable with plug, part number 406209-941.

Pin assignment: Connector front view on the VHF radio.

21 3 4 5

Pin Description Wire color

1 NMEA in+ Brown

2 NMEA in- Blue

12

34

105

6

78

9

Power, VHF antenna and external equipment 57


3 NMEA out- White

4 NMEA out+ Green

5 Mike 2 Yellow

6 EAR 2 Grey

7 Hook_PTT Pink

8 Battery supply when radio is on Red

9 Internal GND = - Battery Black

10 Internal GND = - Battery Orange — SCREEN (Drain)

Pin Description Wire color

58 Power, VHF antenna and external equipment


33333

Inst

alla

tion

NMEA interface description

The NMEA interface supports NMEA 0183 v2.0, v2.1 and v2.3.

NMEA interface Specifications

NMEA input:Impedance: 600 Ohm

Max. 2mA at min. level of 2V

NMEA outputLoad Impedance: > 60 Ohm

Drive load: < 35 mA



The following sentences are supported:

• FSI: All fields are decoded.

• GGA: UTC, "Position", "quality indicator" (indicators 1-5). All other fields are

unused.

• GLL: UTC, "Position", "Status" and "mode" (indicators A and D). All other

fields are unused.

• GNS: UTC, "Position" and "mode" (indicators A and D). All other fields are

unused.

• RMC: UTC, "Position", "Status", "Date" and "mode" (indicators A and D). All

other fields are unused.

• ZDA: UTC, "Day", "Month", and "Year". All other fields are unused.

In accordance with the standard EN61162-1:2008 and EN61162-2:1998

Received NMEA sentences except for FSI can be forwarded to NMEA output. As

talker the sentences are streamed when received (with no intervals).

HW revision: 57-127368-D.02

SW revision: 2.00.01



33333

Inst

alla

tion

CTRL connector for control speaker microphone

Connector type: Circular connector, 12pin.

Pin assignment: Connector front view on the VHF radio:

Pin Description Pin Description

1 GND for cable screen 7 Internal GND = - Battery

2 Internal GND=- Battery 8 not used

3 Battery supply when radio is on 9 RX out +

4 Battery supply when radio is on 10 RX out -

5 CAN+ 11 TX in +

6 CAN- 12 TX in -

12

113

410

12

56

78

9



Power, Loudhailer, foghorn and external speaker

Use the connector marked

PWR/EXT to connect power,

loudhailer and an external

speaker. The cable for this

connector is part of the

delivery.

1. Blue wire: Power -

2. Red isolation on inner

connector: loudhailer

3. White isolation on inner

connector: external

speaker

4. Red wire: Power +

21 3 4



33333

Inst

alla

tion

Protection against water ingress

VHF antenna

Use the connector marked ANT to connect the VHF antenna to the radio with a

50 Ohm coaxial cable with low loss, e.g. RG214. Install a PL259 plug at the

cable end.

Place the antenna as high and clear of obstructions as possible. Make sure

that the horizontal distance to metal parts is minimum 1.5 m (5 ft).

Connector type: female SO239 for PL259 plug.

Ground stud

To ground the radio connect a ground wire from

the ground stud of the radio to a suitable

grounding point. Use an appropriately sized

wire. The ground stud is located above the VHF

antenna connector.

Important You must protect the cable connection with rubber vulcanizing

tape as shown in the pictures below. This protection prevents

water seeping into the VHF radio, cable and connectors.

1 2

3

4



System setup

To change a setting in the SYSTEM SETUP, do as follows:



2. Press the arrow soft key or to advance to SYSTEM SETUP.



4. Press EXIT to return to normal radio operation

.

SYSTEM SETUP Description

System time & Date View and set system time and date

Inactivity timeout Inactivity time-out to exit functions (e.g. in

setup) and return to the application.

Range: 1 to 30 minutes, in 1 minute steps

Default: 10 min.

NMEA input (baud rate) 4800

Factory Defaults Resets the radio to factory defaults.

SW version Software version of the radio

S/N Serial number of the radio

Password If you need to change the identity of the radio

(MMSI number or ATIS code), contact your

local dealer.

64 System setup


33333

Inst

alla

tion

SAILOR 6201 Handset cradle (optional)

This Handset has a hook-on/off function,which is activated by a small magnet embeddedin the cradle.The cradle must be installed as illustrated inorder to ensure the hook-on/off functionalityof the Handset.

7562

226

* 120

min. 100 Space for handset access

Spac

e fo

r ca

ble

and

hand

set

cable

5445

135

39655C

Drilling plan

SAILOR 6201 Handset cradle (optional) 65


66 SAILOR 6201 Handset cradle (optional)

Chapter 444444

Serv

ice

& m

ain

ten

ance

Service & maintenance 4

Contact for support

Contact your authorized dealer for technical service and support of the VHF

radio. Before contacting your authorized dealer you can go through the

troubleshooting guide to solve some of the most common operational

problems.

Maintenance

Preventive maintenance

Maintenance of the SAILOR 6216 VHF DSC can be reduced to a maintenance

check at each visit of the service staff. Inspect the radio for mechanical

damages, salt deposits, corrosion and any foreign material. Due to its robust

construction and ruggedness the radio has a long lifetime. Anyway it must

carefully be checked at intervals not longer than 12 months - dependent on the

current working conditions.

Salt deposits

In case the equipment has been exposed to sea water there is a risk of salt

crystallization on the keys and wheel knobs and they may become inoperable.

Clean the VHF radio and speaker microphones with fresh water.

Error messages and warnings

Errors and warning messages are shown in the display and are read-only.

67

Chapter 4: Service & maintenance

DSC self test

To run a control routine DSC self test, do as follows:



2. Press the arrow soft key or to advance to DSC SETUP.

3. Turn the selector wheel knob to select DSC Self Test. Press and turn the

selector wheel knob to select RUN.

The test will check the ability to encode/decode DSC signalling on RF level.

The radio will automatically transmit a DSC safety test call to its own MMSI

number without enabling the transmitter power amplifier. In parallel the

radio decodes and compares the received call to be the same as the

transmitted.

The display shows the result of

the test.

4. Press the soft key OK to

acknowledge the test result and

resume normal operation.

Important If the DSC loopback test fails, this indicates the DSC

functionality does not work correctly — including the ability to

send a DISTRESS message.

Contact your dealer immediately for further advice.

68 Maintenance


44444

Serv

ice

& m

ain

ten

ance

Troubleshooting guide

Action Symptom Remedy

The radio will

not turn on

The display is

empty.

Check if power is present.

Check fuse which is placed in the + supply

wire.

Check performance of power supply if

connected to one.

No commu-

nication

The

loudspeaker

is mute.

Check the antenna installation.

Check antenna cable.

Check handset/Handmicrophone and cable.

GPS Position

requested.

If the VHF, despite being connected to a

GPS/position source, prompts for entering the

position and time information, the automated

update has most likely been lost either due to

missing data on the line, broken cabling or the

GPS/position source has failed. Refer to the

installation section in the back of this manual

for installation and connection details.

Until the automatic position update from

GPS/position source is restored position and

time must be entered manually when

prompted by a (four hour) timer in VHF.

In the DSC SETUP, Position Info, you can verity

the position data. If data is present

Lat/Lon/UTC will be displayed.

Maintenance 69


DSC routine

testing

Check the DSC function regularly. Verify the

complete DSC installation, with antennas, by

transmitting a Safety Test call to another

station (coast or ship). The test call is

generated using the DSC call flow via menu

CALL.

The call should normally be replied by the

receiving station without questioning. The

default configuration of a DSC VHF radio is

auto-acknowledgement of any received Safety

test call requests. If a ship is equipped with

multiple radios a second radio can be the

station to check up against. The transmitting

radio will not receive its own transmitted calls.

If there is only a single radio on a vessel, a

facility is built into the unit where the DSC

engine can be verified using a test call that is

internally looped without activating the radio

transmitter PA. The test is executed via menu

SETUP, DSC SETUP. The call sequence that is

verified, is an Individual Safety Test Call

directed to own MMSI. The test status is read

in the display.

Missing

MMSI

DSC

operation is

not working

When powering up the VHF for the first time

after leaving factory there is no MMSI number

in the VHF radio. For the DSC operation to

function the MMSI number must be entered in

the VHF radio. For further details see Entering

the MMSI number on page 7.


70 Maintenance


44444

Serv

ice

& m

ain

ten

ance

Radio time DSC logs are

sorted with

wrong time

stamp or

radio time is

incorrect

A wrong radio time indication should occur

only if GPS position source is not connected or

providing correct time data. A valid GPS time

signal will update the UTC time used for time

stamping the DSC logs.

If a GPS/position source is not connected to

the VHF radio and hence position and time is

entered manually, you must enter the "radio

time" also manually, at least after power up.

This will ensure correct time stamping of the

DSC logs.

The UTC time is the suggested time to be

entered when prompted for entering position

and time manually (every four hours).

DSC Channel

not free

DSC

transmission

delayed

The transmission of a DSC call which is not of

category distress or urgency will be postponed

if the VHF radio is in the process of decoding

an incoming DSC call. As soon as this decoding

process has finalized the transmission will take

place.

Handset

configuration

No sound in

earpiece

The earpiece volume may be configured to

OFF. See section Controller setup on page 10

on how to adjust the earpiece volume of the

handset.


Maintenance 71


Device failure If any of the checks and tests described in this

section do not assist in resolving the

difficulties experienced in the operation

and/or performance of the VHF installation, a

fault may have developed in the VHF radio

itself.

When contacting an authorized Thrane &

Thrane representative be sure to provide as

much information as possible describing the

observed behavior - also including the type of

the VHF radio, its serial number, and software

release version (both found in the setup menu

Controller Setup).


72 Maintenance


44444

Serv

ice

& m

ain

ten

ance

Replacing the fuse in the red wire (Power +)

One fuse is installed in the supplied

DC cable. If the fuse is blown, track

down why the fuse was blown and

solve the problem. To replace the

fuse, do as follows:

1. Hold both ends of the fuse holder

and pull it apart.

2. Take out the old fuse.

3. Insert the new fuse. The fuse

rating is 10 A T.

4. Make sure that the fuse is tightly

fixed on the metal contact inside

the fuse holder.

5. Put together the fuse holder.

1

2

3

Maintenance 73


Equipment and accessories

SAILOR 6209 Accessory connection box

You can use the SAILOR 6209 Accessory

Connection Box to combine GPS (NMEA),

GPS/AIS DSC modem and the SAILOR 6201

Handset option.

The wire terminal blocks are connected in

parallel.

Warranty

For repair or replacement of the VHF radio within terms of warranty, contact

your local dealer.

36090

74 Equipment and accessories

Appendix AAAAAA

Tech

nic

al s

pec

ific

atio

ns

Technical specifications A

T

Item Specification

Weight SAILOR 6216 VHF DSC approx. 1.2 kg2,65 lbs

Weight SAILOR 6216 VHF DSC

and Handmicrophone

approx. 1,5 kg 3,31 lbs including SAILOR 6202

Handmicrophone and mounting bracket

Dimensions Height: Outer dimension 106 mm, hole height

for flush mount 89 mm

Width: Outer dimension 190 mm, hole width

for flush mount 177 mm

Depth: Outer dimension from front of wheel

knobs 132 mm, depth for flush mount 94 mm

Operating temperature -15°C to 55°C5°F to 131°F

Storage temperature -30°C to 80°C-22°F to 176°F

Power supply 12 VDC Nominal (10,8– 15,6 VDC)

Current consumption Max. 7 A

Frequency range TX 156,000-161,450,

RX 156,000-163.425 MHz

Channel spacing 12,5 kHz and 25 kHz, all international

maritime channels

75

Appendix A: Technical specifications

Item Specification

Number of P channels The radio may be programmed with up to 40

private channels that can be managed in all

channel modes.

Transmit power Hi/Lo: 25 W and <1 W

RF output power 25 W +0 dB / - 1.5 dB

1 W +0 dB / - 1.5 dB

RF output power, Canada 21 W ±0.75 dB / 0.8 W ±0.75 dB

Modulation

25 kHz

12.5 kHz

16K0G3E, 16KOG2B (DSC)

8K05G3E

LF power Built-in loudspeaker: 6 W

External loudspeaker: 6 W / 8 Ohm

Loudhailer: 30 W / 4 Ohm (when the unit is

not transmitting)

Receiver sensitivity < -119 dBm typically @ 20 dB SINAD CCITT

weighted

Antenna 50 Ohm antenna, 50 Ohm female SO239 for

PL259 plug

1-antenna operation for VHF and DSC

communication

Water ingress IPx8 and IPx6 all over. For flush-mount

installations a sealing gasket is included in

the delivery.

76


AAAAA

Tech

nic

al s

pec

ific

atio

ns

NMEA data rates and formats

Item Value

62162-1 4800,8,n,1 (in/out)

62162-2 38400,8,n,1 (out only)

77


78

Appendix BBBBBB

Mar

itim

e ch

ann

els

Maritime channels B

International channels

L) 1 W TX power

*) Channel 87 and 88 became simplex channels following the introduction of

AIS1 at 161.975 MHz and AIS2 on 162.025 MHz.

These are the default channels. Additional narrowband channels can be

enabled, see Radio setup on page 21.

Channels TX RX SIMPLEX DUPLEX Channels TX RX SIMPLEX DUPLEXMHz MHz Intership Port Port Public MHz MHz Intership Port Port Public

1 156,050 160,650 60 156,025 160,6252 156,100 160,700 61 156,075 160,6753 156,150 160,750 62 156,125 160,7254 156,200 160,800 63 156,175 160,7755 156 250 160 850 64 156 225 160 8255 156,250 160,850 64 156,225 160,8256 156,300 156,300 65 156,275 160,8757 156,350 160,950 66 156,325 160,9258 156,400 156,400 67 156,375 156,3759 156,450 156,450 68 156,425 156,42510 156,500 156,500 69 156,475 156,47511 156,550 156,550 70 156,525 156,525 DSC DSC12 156 600 156 600 71 156 575 156 57512 156,600 156,600 71 156,575 156,57513 156,650 156,650 72 156,625 156,62514 156,700 156,700 73 156,675 156,67515 156,750 156,750 74 156,725 156,72516 156,800 156,800 Distress and calling 75 156,775 156,775 L)17 156,850 156,850 76 156,825 156,825 L)18 156,900 161,500 77 156,875 156,87519 156,950 161,550 78 156,925 161,52520 157,000 161,600 79 156,975 161,57521 157,050 161,650 80 157,025 161,62522 157,100 161,700 81 157,075 161,67523 157,150 161,750 82 157,125 161,72524 157,200 161,800 83 157,175 161,77525 157,250 161,850 84 157,225 161,82525 157,250 161,850 84 157,225 161,82526 157,300 161,900 85 157,275 161,87527 157,350 161,950 86 157,325 161,92528 157,400 162,000 87 157,375 157,375 *)

88 157,425 157,425 *)

79

Appendix B: Maritime channels

US channels

L) 1 W TX power. Channels 13, 67 and 77 are limited to low transmission

power.

B) Channels 2, 3, 4, 60, 61, 62, 64, 75 and 76 cannot be selected in US mode.

!) Channels 21A, 22A, 23A, 81A, 82A and 83A may be legally used in some

circumstances but not by the general public in US waters.

RX) Only RX: transmissions are blocked.

*) Channels 87 and 88 became simplex channels following the introduction of




Channels TX RX SIMPLEX DUPLEX Channels TX RX SIMPLEX DUPLEX Channels RXMHz MHz MHz MHz MHz

1A 156,050 156,050 60 B) W1 162,5502 B) 61 B) W2 162,4003 B) 62 B) W3 162,4754 B) 63A 156,175 156,175 W4 162,4255A 156,250 156,250 64 B) W5 162,4506 156,300 156,300 65A 156,275 156,275 W6 162,5007A 156,350 156,350 66A 156,325 156,325 W7 162,5258 156,400 156,400 67 156,375 156,375 L)9 156,450 156,450 68 156,425 156,42510 156,500 156,500 69 156,475 156,47511 156,550 156,550 70 156,525 156,525 DSC12 156,600 156,600 71 156,575 156,575 L)13 156,650 156,650 L) 72 156,625 156,62514 156,700 156,700 73 156,675 156,67515B 156,750 RX) 74 156,725 156,72516 156,800 156,800 Distress and calling 75 B)17 156,850 156,850 76 B)18A 156,900 156,900 77 156,875 156,87519A 156,950 156,950 78A 156,925 156,92520 157,000 161,600 79A 156,975 156,97520A 157,000 157,000 80A 157,025 157,02521A 157,050 157,050 !) 81A 157,075 157,075 !)22A 157,100 157,100 !) 82A 157,125 157,125 !)23A 157,150 157,150 !) 83A 157,175 157,175 !)24 157,200 161,800 84 157,225 161,82525 157,250 161,850 85 157,275 161,87526 157,300 161,900 86 157,325 161,92527 157,350 161,950 87A 157,375 157,375 *)28 157,400 162,000 88A 157,425 157,425 *)

80


BBBBB

Mar

itim

e ch

ann

els

Ca channels

L) 1 W TX power. Channels 15, 17, 20, 65, 66, 75, 76 and 77 are limited to 1 W

transmission power.

!) Channels 4A, 6, 19A, 21A, 22A, 61A, 62A, 63A, 67, 72, 73, 81A, 82A and 83A

may be legally used in some circumstances but not by the general public in

CA waters.

RX) Only RX: transmission is blocked.





Channels TX RX SIMPLEX DUPLEX Channels TX RX SIMPLEX DUPLEX Channels RXMHz MHz MHz MHz MHz

1 156,050 160,650 60 156,025 160,625 W1 162,5502 156,100 160,700 61A 156,075 156,075 !) W2 162,4003 156,150 160,750 62A 156,125 156,125 !) W3 162,4754A 156,200 156,200 !) 63A 156,175 156,175 !) W4 162,4255A 156,250 156,250 64 156,225 160,825 W5 162,4506 156,300 156,300 !) 64A 156,225 156,225 W6 162,5007A 156,350 156,350 65A 156,275 156,275 L) W7 162,5258 156,400 156,400 66A 156,325 156,325 L)9 156,450 156,450 67 156,375 156,375 !)10 156,500 156,500 68 156,425 156,42511 156,550 156,550 69 156,475 156,47512 156,600 156,600 70 156,525 156,525 DSC13 156,650 156,650 71 156,575 156,57514 156,700 156,700 72 156,625 156,625 !)15 156,750 156,750 L) 73 156,675 156,675 !)16 156,800 156,800 Distress and calling 74 156,725 156,72517 156,850 156,850 L) 75 156,775 156,775 L)18A 156,900 156,900 76 156,825 156,825 L)19A 156,950 156,950 !) 77 156,875 156,875 L)20 157,000 161,600 L) 78A 156,925 156,92521A 157,050 157,050 !) 79A 156,975 156,97521B 161,650 RX) 80A 157,025 157,02522A 157,100 157,100 !) 81A 157,075 157,075 !)23 157,150 161,750 82A 157,125 157,125 !)24 157,200 161,800 83A 157,175 157,175 !)25 157,250 161,850 83B 161,775 RX)26 157,300 161,900 84 157,225 161,82527 157,350 161,950 85 157,275 161,87528 157,400 162,000 86 157,325 161,925

87 157,375 157,375 *)88 157,425 157,425 *)

81


Bi channels

L) 1 W TX power on channels 6, 8, 10, 11, 12, 13, 14, 15, 17, 71, 72, 74 and 77.

B) Channels 75 and 76 cannot be selected in BI mode.



NB! The ATIS function is enabled on all channels.

Dual Watch & Scanning modes are disabled.

Alternative channels

If the radio is used in regions where neither of the four described standard

channels are allowed, a reduced channel table with international channel

designators and frequencies can be made. Contact your local dealer for

programming the alternative channels.

Private channels

Up to 40 licensed private channels for non-DSC purposes may be specified.

For programming the private channels contact your local dealer.

Channels TX RX SIMPLEX DUPLEX Channels TX RX SIMPLEX DUPLEXMHz MHz Intership Port Port Public MHz MHz Intership Port Port Public

1 156,050 160,650 60 156,025 160,6252 156,100 160,700 61 156,075 160,6753 156,150 160,750 62 156,125 160,7254 156,200 160,800 63 156,175 160,7755 156,250 160,850 64 156,225 160,8256 156,300 156,300 L) 65 156,275 160,8757 156,350 160,950 66 156,325 160,9258 156,400 156,400 L) 67 156,375 156,3759 156,450 156,450 68 156,425 156,42510 156,500 156,500 L) L) 69 156,475 156,47511 156,550 156,550 L) 70 156,525 156,525 DSC DSC12 156,600 156,600 L) 71 156,575 156,575 L)13 156,650 156,650 L) L) 72 156,625 156,625 L)14 156,700 156,700 L) 73 156,675 156,67515 156,750 156,750 L) L) 74 156,725 156,725 L)16 156,800 156,800 Distress and calling 75 B)17 156,850 156,850 L) L) 76 B)18 156,900 161,500 77 156,875 156,875 L)19 156,950 161,550 78 156,925 161,52520 157,000 161,600 79 156,975 161,57521 157,050 161,650 80 157,025 161,62522 157,100 161,700 81 157,075 161,67523 157,150 161,750 82 157,125 161,72524 157,200 161,800 83 157,175 161,77525 157,250 161,850 84 157,225 161,82526 157,300 161,900 85 157,275 161,87527 157,350 161,950 86 157,325 161,92528 157,400 162,000 87 157,375 157,375 *)

88 157,425 157,425 *)

82

GlossaryCCC
Glossary C
CC

Glo

ssar

y

A

ACC Accessories

AIS Automatic Identification System, a short range coastal tracking

system used on ships and by Vessel Traffic Services for identifying

and locating vessels by electronically exchanging data with other

nearby ships.

ATIS Automatic Transmission Identification System

C

CTRL Control

D

DSC Digital Selective Calling

E

EXT External

G

GGA NMEA sentence, essential fix data which provide 3D location and

accuracy data.

GLL NMEA sentence, Geographic Latitude and Longitude

GNS NMEA sentence,

GPS Global Positioning System

83

Glossary

N

NMEA National Marine Electronics Association, specification for

communication between marine electronic devices

P

PTT Push To Talk

PWR Power

R

RMC NMEA sentence, version of essential gps position, velocity, time

data.

U

UTC Coordinated Universal Time. The International Atomic Time (TAI)

with leap seconds added at irregular intervals to compensate for

the Earth’s slowing rotation. Leap seconds are used to allow UTC

to closely track UT1, which is mean solar time at the Royal

Observatory, Greenwich.

V

VHF Very High Frequency

Z

ZDA NMEA sentence, date and time.

84

IndexDD

Index D

DDD

Ind

ex

Numerics

16/C, 1290 s replay, 48

A

ACC connector, 57

accessories, 74

acknowledgement, distress, 26

action line, display, 3activate

foghorn, 41, 45

scan resume, 21

scanning, 19watch, 18

ADD, 42

add a contact, 42

adjust

squelch, 9adjusting

speaker volume, 6ALT, 82

ALT channel table, 22

ANT connector, 63

ATIS code, 23

change, 64

attenuation control, 17Auto-Ack Individual, 39

Auto-Ack Test, 39

Auto-switch Channel, 40

B

background sessions

DSC, 37

backlight, 1dim, 6

Bi, 82

Bi channels, 82

browse channels, 6

C

Ca channels, 81

cable for VHF antenna, 63

CALL, 41

call

Distress procedure, ivDSC, 24

call channel, program, 15call log, DSC, 38

CAN channel table, 22

cancelling

distress, 27

change

dual and triple watch, 18channel

add to scan, 19naming, 15program, 15remove from scan, 19select, 6working, 6

channel table

ALT, 22, 82

Bi, 82

Ca, 81

CAN, 22

INT, 79

PRIV, 22, 82

US, 22, 80

85

Index

channels

Bi, 82

Ca, 81

international, 79

primary, 14private, 15US, 80

weather, 14Comm Inactivity, 39

compass safe distance, 50

configuration

system example, 4connector

ACC, 57

ANT, 63

CTRL, 61

external speaker, 62

foghorn, 62

loudhailer, 62

VHF antenna, 63

contact, 67

adding, 42

deleting, 43

editing, 43

controls, front plate, 2cradle for 6201, installation, 65

CTRL connector, 61

D

data rate

NMEA, 77

deactivate, 46

foghorn, 46

watch, 18default reset, 64

DELETE, 43

delete contact, 43

86

delivery, items included, 49

dim, 6display, 3distress

acknowledgement, 26

cancelling, 27

display, 25

nature, 25

power failure, 28

received calls, 28

time since activation, 25

distress button, 24

Distress procedure, ivDistress timeout, 39

document number, this manual, iDSC

background sessions, 37

call log, 29, 38

calls, 24

loopback test, 68

multiple calls, 37

session definition, 31

setup, 38

DSC alarms

non distress, 39

DSC headlines, 32

DSC self test, 40

DSC session, 31

typical display, 31

DSC setup, 38

DSC soft keys, 33

dual watch, 21

change to triple, 18

E

editing a contact, 43

emergency calls, iv

Index

DDDDD

Ind

ex

enter position manually, 8error messages, 67

external speaker

cabling, 62

connector, 62

F

factory defaults, 64

flush mount, 54

FOG, 45

foghorn, 1, 45, 46

activate, 41, 45

connector, 62

patterns, 1test tone, 46

foghorn frequency, setup, 47

frequency range, VHF, 75

front plate, controls, 2fuses, how to replace, 73

G

GPS data, 8GPS input, 57, 74

GPS position

display, 8

H

HAIL, 44

hand microphone

installing, 56

Handmicrophone, 9handset cradle

installation, 65

hang time, 21

headline

DSC, 32

HORN, 46

I

input

GPS, 74

handset, 74

NMEA, 64

installation

cradle for 6201, 65

desktop, 51

flush mount, 54

handset cradle, 65

mounting bracket, 53

overhead, 52

INT, 79

IP rating, 76

K

key 16/C, 12keys on front plate, 2

L

LO/HI, 17LOCAL, 17loud hailer, 44

cabling, 62

louder, volume, 6loudhailer, 1

connector, 62

receiving radio channel, 44

low power

override, 17low power, overriding, 17

87

Index

M

manual, document number, imaritime channels, 79

MAYDAY, ivmessage

replay, 48

MMSI

change, 64

MMSI number

reviewing, 8MORE, 10mounting, 50

flush mount, 54

with mounting bracket, 53

multiple calls, DSC, 37

mute

speaker, 9

N

NAME, 15name a call channel, 15nature of distress, 25

night vision, how to dim, 6NMEA, 57

data rate, 77

NMEA input, 64

NMEA interface, 59

NMEA output, 59

Non-dist Inactivity, 39

Non-distr.alarms, 39

O

overriding low power, 17

88

P

PA

talk-back, 44

password, 64

PHBOOK, 41

phone book, 41

add contact, 42

delete a contact, 43

edit a contact, 43

position

enter manually, 8position data

enter manually, 39

position Info, 39

power

cabling, 62

fuse, 73

off, 6on, 6

power failure

distress, 28

primary channel, program, 15priority scan, 22

PRIV, 82

PRIV channel table, 22

private channels, 15program, call channel, 15PTT button, 12

R

radio call

making, 13receiving, 13

radio channel, loudhailer, 44

received distress calls, 28

Index

DDDDD

Ind

ex

replay, 1, 48

button, 2reset to default, 64

resume time, 21

review MMSI number, 8run

DSC self test, 40

S

safety summary, iiisalt deposits, 67

scan

add channel, 19hang time, 21

priority, 22

remove channel, 19resume time, 21

resume, activate, 21

scanning

start, 19selector wheel knob, 2, 6self test, 68

DSC, 40

semi duplex, 1serial number, 64

service line, display, 3setup

controller, 10DSC, 38

foghorn frequency, 47

Radio, 21

system, 64

watch, 21

simplex, 1

soft key

ADD, 42

CALL, 41

DELETE, 43

DSC, 33

FOG, 45

HAIL, 44

HORN, 46

LOCAL, 17MORE, 10NAME, 15OVRIDE, 17PHBOOK, 41

STOP, 48

TAG, 19WATCH, 18WX, 20

soft keys, 9softer, volume, 6Software version, 64

speaker volume, 6speaking devices, 9specifications, 75

squelch, 9squelch control, 2, 9STOP, 48

stop

replaying a message, 48

watch or scan, 18, 19support, 67

SW version, 64

system configuration

example, 4system setup, 64

89

Index

T

TAG, 19remove, 19

talk back, 47

technical data, 75

temperature

operational, 75

storage, 75

testing, foghorn, 46

time out

non distress, 39

timeout, 64

Distress, 39

VHF and other non distress, 39

triple watch, 21

change to dual, 18

U

US, 80

US channel table, 22, 80

Use GPS, 8UTC time, 3

enter manually, 8

V

VHF

antenna cable, 63

antenna connector, 63

channels, 14frequency range, 75

volume

louder, 6softer, 6speaker, 6

Volume wheel knob, 2

90

W

warnings, 67

warranty, 74

limitation, iiiWATCH, 18, 19watch

dual and triple, 18dual or triple, 21

setup, 21

start, 18stop, 18

water ingress, 76

weather channels, 14weight, 75

wheel knob

selector, 2volume, 2

working channel, 6WX, 20

[email protected] • www.thrane.com

TT98-128825-THR-E

SAILOR 6216 VHF DSC - Telemar Norge · SAILOR 6216 VHF DSC User and installation manual Document...

Documents

Transcript of SAILOR 6216 VHF DSC - Telemar Norge · SAILOR 6216 VHF DSC User and installation manual Document...