RS485-CAN MCON-232 Integration Module MCON-232 ......to the CAN Ampio Smart Home standard. It is a...
Transcript of RS485-CAN MCON-232 Integration Module MCON-232 ......to the CAN Ampio Smart Home standard. It is a...
General featuresMCON-232 module is a component of the Ampio Smart Home systemand is designed to convert the transmission from devicesequipped with RS232 port to CAN-Bus standard.
Module is controlled via CAN-Bus. Required voltage to power the module is 11-16V DC.
The device is equipped with RS232 connector, CAN bus connector,and two LED indicators, green and red.
The green LED indicates the status of CAN communication
one regular flash every 1 sec. - CAN-Bus communication in order two regular flashes every 1 sec. - module is not receiving information from other SmartHome modules three regular flashes every 1 sec. - module cannot send information to CAN-Bus
The red LED indicates transmission via RS232 port.
The module provides integration of any device equipped with RS232serial port with the Ampio Smart Home system. These include air conditioning units, recuperators, home audio systems, TV, home alarms etc.
SoftwareIts multi-functionality is the reason why MCON-232 module is one of very few devices which do not update automatically. Software is uploaded manually by choosing correct program file.
Dedicated software is identified by its filename with the syntaxmostly compatible with naming standards assumed for updatesof Ampio Smart Home devices. The only difference is that last twodigits of the software version specify its purpose.
The filename template interpretation is as follows:: ampio_TXXX_PYYY_SZZZTT.amp
XXX device type, 25 for MCON devices;YYY hardware version;ZZZ software version;TT software purpose.
Symbol Description
TEST Software for testing the device
INTEGRA Integration with Satel Integra alarm system
UNI-ONEWAY Oneway integrations, sending any commands
SPECIAL Software made for specific integrations
List of aviable softwares for different values
Technical dataPower supply voltage
11-16V DC
Current consumption 50 mA
Communication connector RS232
Dimensionswidth 35 mmheigth 120 mmdepth 65 mm
maximal 400 mA quiescent
MCON-232RS232-CAN Integration Module
ver 1.7, 27.08.2020 Copyright © 2020 Ampio Sp. z o.o. All rights reserved. This document is not intended for reproduction or distribution.
www.ampio.pl
MODULE DESCRIPTION
MCON-232RS232-CAN Integration Module
90
12
0 35
55
,75
90
51
65
CANLOW
CANHI
+12V DC
GND+
RS232
MODULE MCON-232CAN - RS232
TX GNDRX
GND
RX
TX1
5
6
9
SideMCON232
DB-9 plug connected to
the integrated device
INTEGRATED DEVICEin the case of devices verifying the DSR signal,
such as a SATEL INTEGRA, you need to make
an additional jumper marked in red in the picture
ATTENTION:
ver 1.7, 27.08.2020 Copyright © 2020 Ampio Sp. z o.o. All rights reserved. This document is not intended for reproduction or distribution.
www.ampio.pl
Dimensions expressed in mm
MODULE DIMENSIONS
CANLOW
CANHI
+12V DC
GND+
RS232
MODULE MCON-232CAN - RS232
TX GNDRX
GN
D
+1
2V
CA
N L
ow
CA
N H
igh
9
8
7
6
5
4
3
2
1
5
4
3
2
1
9
8
7
6
Pinout of individual pins
of the RS-232 connector
RS-232DB-9 connector
of integrated device
CAN Network 4
* Pin and short circuit is only required on certain devices1, 4 6
MCON-232RS232-CAN Integration Module
ver 1.7, 27.08.2020 Copyright © 2020 Ampio Sp. z o.o. All rights reserved. This document is not intended for reproduction or distribution.
www.ampio.pl
CONNECTION DIAGRAM