RS1B-DC3 - Amazon S3images.idatalink.com/corporate/Content/Manuals/COM-PG/COM-PG-[RS1B-DC3... ·...
Transcript of RS1B-DC3 - Amazon S3images.idatalink.com/corporate/Content/Manuals/COM-PG/COM-PG-[RS1B-DC3... ·...
REVISION DATE20170829
DOCUMENT NUMBER
NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.
U.S. Patent No. 8,856,780
PRODUCT GUIDERS1B-DC3
www.idatalink.comAutomotive Data Solutions Inc. © 2017
U.S. Patent No. 8,856,780
GETTING STARTED
WELCOME
NEED HELP?
Congratulations on the purchase of your RS1B-DC3 solution. You are now a few simple steps away from enjoying your new remote starter unit with enhanced features. Before starting your installation, please ensure that your RS1B-DC3 module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
1 866 427-2999
idatalink.com/supportwww.12voltdata.com/forumwww.facebook.com/groups/idatatech
TABLE OF CONTENTS
Box Contents 3
Tach Programming Procedure 4
Remote Programming Procedure 5
Valet Mode Programming Procedure 6
Compatible Accessories 7
Online Module Settings 9
Module Diagnostics 10
Remote Starter Error Codes 11
Module Reset Procedure 12
www.idatalink.comAutomotive Data Solutions Inc. © 2017 RS1B-DC3
PAGE 2 OF 12• 20170829
U.S. Patent No. 8,856,780
453
21
6
M6
FUNCTIONS DEFINED BY FIRMWARE
AUTOMATICTRANSMISSION
CUT LOOP
BOX CONTENTS
FT-DAS - 4 PIN REDBLE - 4 PIN YELLOW
RF PORT - 4 PIN BLUE
DRONE - 4 PIN GRAY
M6 - 6 PIN BLACK
PROGRAMMING BUTTON
M2 - 12 PIN BLACK
M3 - 10 PIN WHITE
LED 1LED 2
FT-DAS SENSITIVTY ADJUSTMENT DIALWEBLINK PORT - 4 PIN BLACK
HOOD SWITCHSTICKERS
MODULECM-DC3
79
3
10864
12
5
79
3
108
1112
64
12
5
79
3
108
111314
12
1517181920
16
64
12
5
453
21
6
M5
M4
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK RELEASE (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK RELEASE (-) OUTPUT04 GREEN/WHITE•BLACK DOT - ARM (-) OUTPUT04 GREEN/WHITE•BLACK DOT - ARM (-) OUTPUT05 GREEN/BLACK•BLACK DOT - DISARM (-) OUTPUT05 GREEN/BLACK•BLACK DOT - DISARM (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 BROWN•BLACK DOT - SIREN (+) OUTPUT07 BROWN•BLACK DOT - SIREN (+) OUTPUT08 WHITE/PURPLE•BLACK DOT - HORN (-) OUTPUT08 WHITE/PURPLE•BLACK DOT - HORN (-) OUTPUT09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT11 BROWN/BLACK•BLACK DOT - GROUND WHEN ARMED (-) OUTPUT11 BROWN/BLACK•BLACK DOT - GROUND WHEN ARMED (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
01 BROWN•SILVER DOT - BRAKE (+) INPUT02 BLACK/WHITE•SILVER DOT - E-BRAKE (-) INPUT03 PURPLE•SILVER DOT - DOOR (+) INPUT04 GREEN•SILVER DOT - DOOR (-) INPUT05 PURPLE/WHITE•SILVER DOT - TACH (-) INPUT06 WHITE/BLUE•SILVER DOT - X-TRIGGER (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT08 BLUE•SILVER DOT - TRUNK (-) INPUT09 GRAY/BLACK•SILVER DOT - GLOW PLUG (+) INPUT10 TAN•SILVER DOT - EXT ALARM SENSOR (-) INPUT
FUNCTIONS DEFINED BY FIRMWARE
FUNCTIONS DEFINED BY FIRMWARE
M3
M2
RPS SENSOR - 4 PIN WHITE
SENSOR 2 - 4 PIN GREEN
ALARM LED - 2 PIN WHITETEMP SENSOR - 2 PIN BLUE
BATTERY - 2 PIN WHITEM5 - 6 PIN BLUE
M4 - 20 PIN BLACK
2X
BOX CONTENTS - 1 OF 1
M1 - SOLD SEPARATELY, SEE COMPATIBLE ACCESSORIES
M1 - 8 PIN BLACK
www.idatalink.comAutomotive Data Solutions Inc. © 2017 RS1B-DC3
PAGE 3 OF 12• 20170829
U.S. Patent No. 8,856,780
01
ENGINESTARTSTOP
OFF ACC ON STARTSTARTSTART
02
03
04
05
06
TACH PROGRAMMING PROCEDURE - 1 OF 1
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button. (OR if the remotes are already programmed to the vehicle, press and hold the start button of the remote for 2.5 seconds.)
Wait, LED 2 will fl ash GREEN. (See the Module Diagnostics page)
Release the brake pedal.
Module Programming Procedure completed.
www.idatalink.comAutomotive Data Solutions Inc. © 2017 RS1B-DC3
PAGE 4 OF 12• 20170829
U.S. Patent No. 8,856,780
>>
01
02
ENGINESTARTSTOP
OFF ACC ON STARTON
03
04
05
06
>>
07
08
ENGINESTARTSTOP
OFF ACC ON STARTOFF
09
AFTERMARKET REMOTE PROGRAMMING PROCEDURE - 1 OF 1
WARNING: Program aftermarket remotes before usage. A maximum of four [4x] aftermarket remotes per system.
Time restriction. Complete next step within 7 seconds.
Cycle ignition ON fi ve times [5x OFF/ON] rapidly.
Parking Light will fl ash once [1x].
Time restriction. Complete next step within 5 seconds from previous step.
Press once [1x] on LOCK button of aftermarket remote.
Parking Light will fl ash once [1x].
To program additional remotes: repeat steps 4 to 6 using each additional remote.
Wait, Parking Light will fl ash twice [2x].
Turn ignition to OFF position.
Aftermarket Remote Programming Procedure completed.
www.idatalink.comAutomotive Data Solutions Inc. © 2017 RS1B-DC3
PAGE 5 OF 12• 20170829
U.S. Patent No. 8,856,780
>>
01
02
ENGINESTARTSTOP
OFF ACC ON STARTON
03
04
05
ENGINESTARTSTOP
OFF ACC ON STARTOFF
06
>>
VALET MODE PROGRAMMING PROCEDURE - 1 OF 1
NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming.
Time restriction. Complete next step within 7 seconds.
Cycle ignition ON twice [2x OFF/ON] rapidly.
Press and release the BRAKE pedal three times [3x].
Parking Light will fl ash once [1x] then will fl ash twice [2x].
Set ignition to OFF position.
Valet Mode Programming Procedure completed.
To exit valet mode: repeat steps 1 to 5.
www.idatalink.comAutomotive Data Solutions Inc. © 2017 RS1B-DC3
PAGE 6 OF 12• 20170829
U.S. Patent No. 8,856,780www.idatalink.comAutomotive Data Solutions Inc. © 2017 RS1B-DC3
PAGE 7 OF 12• 20170829
COMPATIBLE ACCESSORIES - 1 OF 2
MODULETELEMATIC PORT
DRONE
(NC)
TELEMATIC KIT (accessory sold separately)
10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
9
WEBLINK MOBILE (accessory sold separately)
MOBILE DEVICE PORT
OBDII CONNECTOR
4 PIN BLACK CABLEMODULE WEBLINK PORT
OBDII CONNECTOR
WEBLINK CABLE (required accessory sold separately)
WEBLINK CABLE
COMPUTERUSB PORT
4 PIN BLACK CABLE
MODULE WEBLINK PORT
U.S. Patent No. 8,856,780www.idatalink.comAutomotive Data Solutions Inc. © 2017 RS1B-DC3
PAGE 8 OF 12• 20170829
COMPATIBLE ACCESSORIES - 2 OF 2
RF KIT
RF KIT (accessories sold separately)
ANTENNA
MODULERF PORT
TEMPERATURE SENSOR
TEMPERATURE SENSOR (accessories sold separately)
MODULE2 PIN BLUE
4
2
8
1
3
5
7
6
M1
MODULEM1
ANALOG HARNESS FT-HRN-DC3-PWR (sold separately)
01 ORANGE - ACCESSORY (+)01 ORANGE - ACCESSORY (+)02 RED - POWER (30A)02 RED - POWER (30A)03 PURPLE - STARTER (+)03 PURPLE - STARTER (+)04 PINK/WHITE - PROG. RELAY #4 - IGNITION 2 (+) (DEFAULT)04 PINK/WHITE - PROG. RELAY #4 - IGNITION 2 (+) (DEFAULT)05 PINK - IGNITION (+)05 PINK - IGNITION (+)
07 RED - POWER (30A)07 RED - POWER (30A)08 BLACK - GROUND08 BLACK - GROUND
06 WHITE - PROG. RELAY #5 (10A) - PARKING LIGHTS (+) (DEFAULT)06 WHITE - PROG. RELAY #5 (10A) - PARKING LIGHTS (+) (DEFAULT)
07 BROWN•BLACK DOT - SIREN (+) OUTPUT REDBLACK SIREN
ALARM LEDFT-DAS
MODULE12 PIN BLACK
MODULE2 PIN WHITE
MODULE4 PIN RED
ALARM KIT (accessories sold separately)
U.S. Patent No. 8,856,780
ONLINE MODULE SETTINGS - 1 OF 1
WEB PROGRAMMABLE MENUS DESCRIPTIONMENU 1 – Remote Starter RS related confi guration optionsMENU 2 – Doorlock Options Convenience feature confi guration optionsMENU 3 – Security Options Alarm activation and settingsMENU 4 – AUX function assignments Set transmitter AUX buttons controlsMENU 5 – Programmable outputs (POC) Set actions for programmable outputsMENU 6 – Pulse Timer Output Confi guration (PTO) Set duration for pulse timer outputs (if used)MENU 7 – Input Confi gurations Set inputs for Auto by fi rmware/Data/AnalogMENU 8 – Output Confi gurations Set outputs for Auto by fi rmware/Data/Analog
Programming options are avaible through Weblink and Weblink Mobile only.
www.idatalink.comAutomotive Data Solutions Inc. © 2017 RS1B-DC3
PAGE 9 OF 12• 20170829
U.S. Patent No. 8,856,780
MODULE DIAGNOSTICS - 1 OF 1
TEST MODULE
LED
1 S
TATU
S
DIA
GNO
STIC
I DURING MODULE PROGRAMMING
Flashing RED Missing/wrong information from fi rmware or vehicle.Solid RED Module waiting for more vehicle information.Flashing GREEN Additional steps required to complete module programming.Solid GREEN then OFF Module correctly programmed.OFF No activity or module already programmed.
II DURING TACH PROGRAMMING
1 GREEN fl ash Tach signal programmed in Analog2 GREEN fl ashes Tach signal programmed in Data3 RED fl ashes No tach signal detected4 RED fl ashes System is in valet mode5 RED fl ashes Tach set for ‘VTS’. No tach programming required6 RED fl ashes Tach set for ‘assumed start’. No tach programming required
III DURING REMOTE START
Flashing RED Module incorrectly programmed.Solid RED Module incorrectly programmed.Flashing GREEN Module correctly programmed and operational.Solid GREEN then OFF Reset in progress.OFF Invalid ground when running status from remote starter.
IV WITH IGNITION OFF
Flashing RED Module incorrectly programmed or connected.Solid RED Module not programmed. Waiting for more vehicle information.Flashing GREEN False ground when running status from remote starter.Solid GREEN then OFF Reset in progress.OFF Module at rest and ready for a remote start sequence.
www.idatalink.comAutomotive Data Solutions Inc. © 2017 RS1B-DC3
PAGE 10 OF 12• 20170829
U.S. Patent No. 8,856,780
REMOTE STARTER ERROR CODES - 1 OF 1
REMOTE STARTER ERROR CODES:NOTES
[X] N
UM
BER
OF
PAR
KIN
G LI
GHT
FLAS
HES
DIA
GNO
STIC
I WARNING: The following applies only when the parking lights are connected and supported by the system.
01 Engine running. 02 Key in ignition at ON position.
II After a remote starter failure, the parking lights will fl ash three [3x] times, then will fl ash [X] number times to indicate an error code. See table.
03 Door is open.04 Trunk is open.05 Foot brake is ON. 06 Hood is open.07 The reservation is OFF. (Manual transmission only)08 Tach failure.09 The vehicle is moving (VSS).10 System is in Valet Mode. 11 CAN communication failure12 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.13 Bypass problem.
REMOTE STARTER SHUTDOWN ERROR CODES:NOTES
[Y] N
UM
BER
OF
PAR
KIN
G LI
GHT
FLAS
HES
DIA
GNO
STIC
I WARNING: The following applies only when the parking lights are connected and supported by the system.
01 Engine tach signal is lost.02 Emergency brake is lost.
II If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for 2.5 seconds when using a 1-WAY remote. OR Press once [1x] on button “4” when using a 2-WAY remote.
The parking lights will fl ash four [4x] times, then will fl ash [Y] number times to indicate an error code. See table.
03 Foot brake is ON. 04 Hood is open.05 Engine RPM limiter is ON.06 Glow plug timeout error.07 Vehicle is moving (VSS).08 N/A09 N/A10 Door is open.11 CAN communication failure during RS sequence.12 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.13 Takeover is not allowed.14 Shutdown error, board overheat protection.
www.idatalink.comAutomotive Data Solutions Inc. © 2017 RS1B-DC3
PAGE 11 OF 12• 20170829
U.S. Patent No. 8,856,780
>>
01
02
03
04
05
06
07
08
>>
MODULE RESET PROCEDURE - 1 OF 1
The following procedure resets the module programming to the vehicle. It does not reset any settings confi gured online.
Disconnect all connectors from module except the M1 BLACK 8-pin connector and the M4 BLACK 20-pin connector.
Disconnect the M1 BLACK 8-pin connector and the M4 BLACK 20-pin connector.
PRESS AND HOLD the module’s programming button while connecting the M1 BLACK 8-pin connector and the M4 BLACK 20-pin connector.
Wait, LED 1 will flash RED. RELEASE programming button.
LED 1 will turn RED for 2 seconds.
Module RESET completed.
Reconnect all connectors.
Repeat programming procedure.
Failure to follow procedure may result with a DTC or a CHECK ENGINE error message.
www.idatalink.comAutomotive Data Solutions Inc. © 2017 RS1B-DC3
PAGE 12 OF 12• 20170829