RPH Hyd winch Final layoutDN - AW Direct: · PDF fileramsey.com winch dimensions dimensions...
Transcript of RPH Hyd winch Final layoutDN - AW Direct: · PDF fileramsey.com winch dimensions dimensions...
ramsey.com
Winch Dimensions
DIMENSIONS SHOWN ARE INCHES OVER MILLIMETERSWINCH MOUNTING CAPSCREWS MUST MEET OR EXCEED SAE GRADE 5 SPECIFICATION
*NOTE: THESE HOLE LOCATIONS MUST BE HELD WITHIN .03” (0.8 MM) OF TRUE POSITION. RECOMMENDED MOUNTING HOLE DIAMETER IS .53” (13.5 MM).
Applications• Towing & Recovery• Petroleum
• Forestry• Mining
• Construction• Refuse
4 5
• Rated Line pull 8,000 lbs
• Recommended cable 3/8”
• Available with a Blocked Clutch
Specifications
Rated Line Pull
Gear Reduction
Weight (without cable)
8,000 lbs.………………. (3,620 kgs)
………………………………. 5.1:1
RPH 8,000-S………… 90 lbs. (41 kgs)RPH 8,000-Y……….85 lbs. (38.5 kgs)
LAYER OF CABLE
*RATED LINE PULLPER LAYER
RPH – 8000 – S
RPH – 8000 – Y
LINE SPEED (at 15 GPM)
Lbs.Kgs.
Ft.M.
Ft.M.
1
8,0003,620
257.0
154.0
FPM(MPM)
50(15.2)
2
6,8003,080
5516.0
3510.0
FPM(MPM)
58(17.6)
3
5,9002,670
9027.0
6018.0
FPM(MPM)
67(20.3)
4
5,2002,350
13039.0
8525.0
FPM(MPM)
76(23.1)
5
4,7002,120
17051.0
11534.0
FPM(MPM)
84(25.5)
* These specifications are based on recommended cable of 3/8” EIPS cable.
Hydraulic Systems Performance 14.9 Cubic Inch Motor
Applications• Towing & Recovery• Petroleum
• Forestry• Mining
• Construction• Refuse
50
40
30
20
10
LINE
SPE
ED F
IRST
LAY
ER (F
PM)
0 5 10 15 FLOW (GPM)
8,000
7,000
6,000
5,000
4,000
3,000
2,0001,000
00 1,000 2,000 3,000
WORKING PRESSURE (PSI)
LINE
PUL
L-FI
RST
LAYE
R (L
BS.)
WIT
HOUT
COU
NTER
BAL
ANCE
VALV
E
WIT
H CO
UNTE
R BA
LANC
E VA
LVE
Winch Dimensions
Hydraulic Systems Performance 24.9 Cubic Inch Motor
*10,000
8,000
6,000
4,000
2,000
00 500 1,000 1,500 2,000 2,500
LINE
PUL
L-FI
RST
LAYE
R (L
BS.)
WORKING PRESSURE (PSI)
35
30
25
20
15
10
5
0
LINE
SPE
ED-F
IRST
LAY
ER (F
PM)
0 5 10 15 FLOW (GPM)
Specifications
• Rated Line pull 10,000 lbs • Recommended cable 7/16”
• Available with a Blocked Clutch
• Meets SAE J706 • Made in the USA
Rated Line Pull
Brake Capacity
Gear Reduction
Weight (without cable)
10,000 lbs.………………. (4,530 kgs)
8,000 lbs…………………(3,620 kgs)
…………………. .……………5.1:1
RPH 10,000-S……… .95 lbs. (43 kgs)RPH 10,000-Y……… .90 lbs. (41 kgs)RPH 10,000-X………100 lbs. (46 kgs)
LAYER OF CABLE
*RATED LINE PULLPER LAYER
**RPH – 10,000 – S
RPH – 10,000 – Y
RPH – 10,000 – X
Lbs.Kgs.
Ft.M.
Ft.M.
Ft.M.
1
10,0004,530
206.0
154.0
206.0
FPM(MPM)
32(9.8)
2
8,3003,760
5015.0
309.0
5015.0
FPM(MPM)
38(11.6)
3
7,1003,220
8024.0
5516.0
8024.0
FPM(MPM)
44(13.4)
4
6,2002,810
11535.0
7522.0
11535.0
FPM(MPM)
51(15.5)
5
16048.0
FPM(MPM)
57(17.4)
LINE SPEED(at 15 GPM)
* These specifications are based on recommended cable of 7/16” EIPS cable.** Last layer does not conform to SAE standard J706.
• Meets SAE J706
• Made in the USA
RPH 8,000 RPH 10,000
DIM.LETTER
A
B
C
RPH 8,000-S(“STD.” DRUM)
9.75247.6
12.25311.1
26.75679.4
RPH 8,000-Y(“Y” DRUM)
6.50165.1
9.00228.6
23.50596.9
DIM.LETTER
A
B
C
RPH 10,000-S(“STD.” DRUM)
9.75247.6
12.25311.1
27.48698.0
RPH 10,000-Y(“Y” DRUM)
6.50165.1
9.00228.6
24.23615.4
RPH 10,000-X(“X” DRUM)
9.75247.6
12.25311.1
27.48698.0
DIMENSIONS SHOWN ARE INCHES OVER MILLIMETERSWINCH MOUNTING CAPSCREWS MUST MEET OR EXCEED SAE GRADE 5 SPECIFICATION
*NOTE: THESE HOLE LOCATIONS MUST BE HELD WITHIN .03” (0.8 MM) OF TRUE POSITION. RECOMMENDED MOUNTING HOLE DIAMETER IS .53” (13.5 MM).
ramsey.com
Table of Contents
Table of contents and limited warranty excerpt……………………………………………………………..2Performance data table…………………………………………………………………………………....3RPH 8,000 Series winches and RPH 10,000 Series winches………………………………………………4-5RPH 12,000 Series winches and RPH 15,000 Series winches………………………….………………….6-7RPH 20,000 Series winches and RPH 25,000 Series winches……………………………………………..8-9RPH 30,000 Series winches and RPH 35,000 Series winches…………………………………………..10-11RPH 45,000 Series winches and RPH 50,000 Series winches…………………………………………..12-13Options for RPH Series: Planetary Hydraulic winches………………………………………………………14
WARNING
Winches are not to be used to lift, support or otherwise transport personnel. A minimum of five (5) wraps of cable around the drum is necessary to support the rated load. Cable clamp is not designed to hold the load.
Limited Warranty Excerpt
Ramsey Winch warrants each new winch to be free from defects in workmanship for a period of one (1) year from date of purchase. The obligation under this warranty, statutory or otherwise, is limited to the replacement or repair at our factory of such part or parts as shall appear to us upon inspection to be defective in materials and workmanship. Complete warranty statement packed with each item.
2 3
How to Select a Winch
1. Determine the line pull required.
2. Determine the size (diameter) and length of cable required.
3. Where will the line load occur–on the first layer of cable on the drum barrel? The second? The third? Refer to the Line Pull and Cable Capacity Per Layer charts in Ramsey performance data on page 3 to determine the proper size winch to meet these line size, length and load requirements.
4. Select the proper winch model and determine the first layer rating required (all performance charts in this brochure are based on the first layer line pull ratings. All winches are rated based on first layer).
EXAMPLE: Customer” A” has a load that requires a 14,000 lb. line pull and has selected 120 ft. of 9/16” cable as the optimum length covering most of his use. His design requires a Planetary Hydraulic winch.
Referring to the charts in the performance data, he notes that 120 ft. of 9/16” cable will build up to three layers on a RPH 20,000* and that the winch provides 14,700 lbs. maximum allowable line pull on the third layer.
The first layer line pull rating of the RPH 20,000 (20,000 lbs.) is now used by customer “A” to determine the hydraulic pressure (PSI) required to provide 14,000 lbs. pull on the 3rd layer as shown on the RPH 20,000 performance data in this manual.
Line speeds shown on the charts in the brochure are also based on the first layer. (First layer line speeds are the slowest of any layer.)
*For performance using wire sizes other than the recommended size, contact the factory.
Performance Data
* Last layer does not conform to SAE Standard J706.** RPH 10,000 Brake capacity 8,000 lbs.
HydraulicPressure Required
For Rated
Line Pull(PSI)
2500
2100
2100
2500
2400
2500
3000
2800
2650
2800
3000
Hydraulic Flow
Required For
Rated Line
Speed(GPM)
15
15
15
15
15
15
15
15
15
25
25
GearRatio
5.1:1
5.1:1
5.1:1
5.1:1
7.7:1
25.53:1
25.53:1
31.89:1
31.89:1
51.35:1
51.35:1
LinePull
(LBS)(KGS)
80003620
10,0004530
10,0004530
12,005440
15,0006800
20,0009070
25,00011,340
30,00013,605
35,00015,909
45,00020,380
50,00022,670
CableCap.(Ft)(M)
257.0154.0
20 6.0154.0
206.0
206.0
3510.0
3510.0
3510.0
309.0
257.60
3510.0
309.0
LineSpeed(FPM)(MPM)
5015.2
329.8
329.8
329.7
257.6
267.9
278.3
195.7
154.6
237.0
237.0
Line Pull
(LBS)KGS)
68003080
83003760
83003760
10,0004530
12,6005710
16,9007660
20,8009430
25,20011,430
28,60013,000
37,70017,100
40,90018,550
CableCap.(Ft)(M)
5516.035
10.0
5015.0309.0
5015.0
5015.0
7522.0
8525.0
7522.0
7522.0
6018.3
7522.0
6519.0
LineSpeed(FPM)(MPM)
5817.6
3811.6
3811.6
3811.5
298.8
309.1
319.5
237.0
185.5
278.2
288.6
Line Pull
(LBS)KGS)
59002670
71003220
71003220
85003850
10,8004890
14,7006660
17,9008110
21,7009840
24,20011,000
32,40014690
34,60015,690
CableCap.(Ft)(M)
9027.060
18.0
8024.055
16.0
8024.0
8024.0
12538.0
13541.0
12538.0
12036.0
10532.0
12538.0
11033.0
LineSpeed(FPM)(MPM)
6720.3
4413.4
4413.4
4413.4
3410.3
3510.6
3611.1
267.9
216.4
329.8
3310.1
Line Pull
(LBS)KGS)
52002350
62002810
62002810
75003400
95004300
13,0005890
15,6007070
19,1008660
21,0009545
28,50012,920
30,00013,600
CableCap.(Ft)(M)
13039.085
25.0
11535.075
22.0
11535.0
11535.0
18054.0
19559.0
18556.0
17553.0
15547.2
18054.0
16048.0
LineSpeed(FPM)(MPM)
7623.1
5115.5
5115.5
5115.5
3911.8
3911.8
4111.8
298.8
237.0
3611.0
3811.7
Line Pull
(LBS)KGS)
47002120
55002490
66002990
85003850
11,6005260
13,9006300
17,0007700
18,5008390
25,30011,460
26,40011,970
CableCap.(Ft)(M)
17051.011534.0
16048.0
16048.0
24073.0
26580.0
24574.0
23571.0
20060.0
24574.0
22066.0
LineSpeed(FPM)(MPM)
8425.5
5717.4
5717.3
4413.4
4413.4
4614.0
3310.0
288.5
4012.2
4313.2
1st Layer 2nd Layer 3rd Layer 4th Layer 5th Layer
WinchModel
RPH 8,000-S
RPH 8,000-Y
RPH 10,000-S
RPH 10,000-Y
RPH 10,000-X
RPH 12,000
RPH 15,000
RPH 20,000
RPH 25,000
RPH 30,000
RPH 35,000
RPH 45,000
RPH 50,000
*
**
Recom-mended
Wire RopeSize
(INCH)(MM)
3/810
7/1611
7/1611
7/1611
1/213
9/1614
5/816
5/816
3/419
3/419
7/822
WinchRating(LBS)
8,000
10,000
10,000
12,000
15,000
20,000
25,000
30,000
35,000
45,000
50,000
Weightwithoutcable(LBS)(KGS)
90418539
95439041
10046
110
50
300136
375170
380
172
486220
568 258
689313
689313
6th Layer
Line Pull
(LBS)KGS)
76003440
15,4006980
22,90010,380
CableCap.(Ft)(M)
31094.0
30091.0
31094.0
LineSpeed(FPM)(MPM)
4814.6
3610.9
4513.7
*
*
*
*
*
*
*
**