RPC PRODUCT PROFILE · 2018. 3. 24. · GRADES OF CRMB MARKETED BY RPC: ch . GRADES OF...
Transcript of RPC PRODUCT PROFILE · 2018. 3. 24. · GRADES OF CRMB MARKETED BY RPC: ch . GRADES OF...
PRODUCTS MARKETED BY RPC :
1). BITUMEN
2). BITUMEN EMULSION
3). CRMB
4). THERMOPLASTIC ROAD MARKING PAINT
5). GLASS BEADS
P E T R O C H E M L L P
GRADES OF BITUMEN MARKETED BY RPC:
(a) VG10 Bitumen:
(b). VG30 Bitumen:
( c ). VG40 Bitumen:
(2).BITUMEN EMULSION FOR ROAD CONSTRUCTION
GRADES OF BITUMEN EMULSION MARKETED BY RPC:
(a). Rapid Setting (RS -1):
(b). Slow Setting (SS -:1) It is used for Prime Coat. Crack sealing and fog seal.
(1). BITUMEN
Bitumen is a common binder used in road construction. It is principally
obtained as a residual product in petroleum reneries after higher fractions like
kerosene and diesel, etc. are removed. Indian Standard Institution
denes Bitumen as a black or dark brown non-crystalline soil or viscous
material having adhesive properties derived from petroleum crude either
by natural or by renery processes.
VG-10 is widely used in spraying applications such as surface dressing and
paving in very cold climate in lieu of old 80/100 Penetra�on grade. It is also used
to manufacture Bitumen Emulsion and Modified Bitumen products.
VG-030 is primarily used to construct extra heavy duty Bitumen pavements
that need to endure substan�al traffic loads. It can be used in lieu of 60/70
Penetra�on grade.
VG-40 is used in highly stressed areas such as intersections, near toll
booths and truck parking lots in lieu of old 30/40 Penetra�on grade Due to its
higher viscosity s�ffer Bitumen mixes can be produced to improve resistance to
shoving and other problems associated with higher temperature and heavy
traffic loads.`
Bitumen emulsions are a dispersion of bitumen in an aqueous continuous
phase stabilized by the addition of an emulsier. They are prepared as
emulsions at high temperatures, but applied as solid dispersions at ambient
temperatures. In road making, bitumen products are typically applied
with mineral aggregate
It is Recommended for tack coat applications
.
GRADES OF CRMB MARKETED BY RPC:
.GRADES OF THERMOPLASTIC MARKETED BY RPC:
MORTH & BS
(3). CRMB : CRUMB RUBBER MODIFIED BITUMEN
CRMB is a blend of selected grades of Bitumen and modier. The rubber
modier used, balances the required visco-elastic balance of the bitumen binder
which improves the resistance to thermal and low temperature cracking
CRMB has good adhesion to different types of aggregates which therefore
reduce cracking deformation etc.
(a). CRMB(-55):
CRMB 55 is ideally suited for moderate climates. Majorly for Surface dressing
Wearing course, Stress absorbing membranes (crack sealing), Stress absorbing
membrane interlayer, Base course, Thin overlays, and more.
(b). CRMB(-60):
CRMB 60 is ideally suited for hot climates. Majorly for Surface dressing, Wearing
course, Stress absorbing membranes (crack sealing), Stress absorbing membrane
interlayer, Base course, Thin overlays, and more.
(4). THERMOPLASTIC ROAD MARKING PAINT
Reective thermoplastic marking material is recommended for use with the
thermoplastic screed application prams, thermoplastic screed application prams
motorised marking machines etc. These products of reective screed are
ideal for high output marking on highways. Thermoplastics has been the
preferred marking material since long in many countries such as the USA, UK,
Europe and Japan where its performance and cost-effectiveness have proved
its benets. In India, liquid paint is fast being replaced by high performance
thermoplastic road makings which have better physico-mechanical properties
and more durability as compare to the commonly used liquid paints
SPECIFICATION AS PER BS: 3262 with White Reective and Yellow Reective
SPECIFICATION AS PER MORTH: 803.4 with White Reective and Yellow Reective
LOOKING FORWARD FOR A EVERLASTING RELATION!!!
GRADES OF GLASS BEADS MARKETED BY RPC:
(a). INTERMIX
(5). GLASS BEADS
Glass beads are used to guide road users in the dark due to the presence of
glass beads on its surface reecting the lights of cars, motorcycles and bicycles.
The glass spheres (retro)reect the headlights of the vehicle to the driver, acting
like a mirror.
Glass beads which are blended into paint and thermoplastics during the
manufacturing stage. These beads are known as Intermix (also called Premix or
In- Mix beads). These beads have high longevity due to their thickness. As the
road marking paint wears over time due to friction from tyres and weathers,
the glass spheres that are embedded into the paint are exposed which ensures
retro-reectivity. This helps to increase the longevity of the paint as well as safety
of motorists.
(b). DROP ONSeveral countries use horizontal road markings. To increase longevity andreectivity of these road marking paints, glass beads are added to the paint atthe time of application These paints are known Drop-on beads. The spheres helpto increase retro-reectivity of the paint during RR (rainy), RI (dry) and RW(wet) conditions.
FOR MORE PRODUCT IMFORMATION, PRODUCTPRICES & ORDER PLACEMENTS AND DELIVERYKINDLY CONTACT:
MR AMAN GAGNEJA +91-9810664949
MR ARVIND SINGH +91-9891241010
2519-20/7, Beadon Pura Karol Bagh, New Delhi - 110005, [email protected]
+91-11-45657114