Robertson grating cat 06FRobertson Grating Products can help you with bar grating, plank grating,...
Transcript of Robertson grating cat 06FRobertson Grating Products can help you with bar grating, plank grating,...
PRESORTEDSTANDARD
U.S. POST AGE PAIDPORTLAND, OR
PERMIT NO. 3995
Robertson Grating Products, Inc.P.O. box 2889Clackamas, OR 97015
Robertson Grating Products Inc.
9180 SE Lawnfi eld Road PO Box 2889
Clackamas, OR 97015
Toll Free: 877-638-6365
Fax: 877-794-5629 Local: 503-794-5629
Local Fax: 503-794-5632e-mail: [email protected] BAR GRATING
PLANK GRATING
FIBERGLASS GRATING
HANDRAIL FITTINGS
SAFETY NOSINGS
POLYDRAIN
PERFORATED METALS
WOVEN WIRE
PRODUCTS AND SERVICE GUIDE
“The Grate Company”
Free Estimates • Complete Fabrication • CAD Drawings
877-638-6365 toll-free • 877-794-5629 fax • Sales e-mail: [email protected]. Box 2889 • Clackamas, OR 97015
Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . .1Steel Bar Grating . . . . . . . . . . . . . . . .2Heavy-Duty Steel Bar Grating . . . . . .3Wheels n’ Heels® Grating . . . . . . . . .4Aluminum Bar Grating . . . . . . . . . . . .5Grating Stair Treads . . . . . . . . . . . . . .6Safety Grating . . . . . . . . . . . . . . . . . .7Slip-Not® Components . . . . . . . . . . . .8Glossary of Terms . . . . . . . . . . . . . . .9Bar Grating Standards . . . . . . . . . . . .10Aluminum Plank . . . . . . . . . . . . . . . . .13RGP Molded Fiberglass Grating . . . .15Pultruded Fiberglass Grating . . . . . . .16RGP Plate & RGP Covered Grating . .18RGP Structural Fiberglass & Hardware .19GRIP-STRUT® Safety Grating . . . . . .20PERF-O GRIP® Grating . . . . . . . . . . .31TRACTION TREAD Flooring . . . . . . .37GRATE LOCK Grating . . . . . . . . . . . .38Pre-Shaped Trench Drain . . . . . . . . .41Drainage Trench Solutions . . . . . . . . .42Foundry Castings . . . . . . . . . . . . . . .43Perforated Metal . . . . . . . . . . . . . . . .44Woven and Welded Wire . . . . . . . . . .45Expanded Metal . . . . . . . . . . . . . . . . .46Handrail Fittings . . . . . . . . . . . . . . . . .47Post Caps & End Caps . . . . . . . . . . .52Caps & Flanges . . . . . . . . . . . . . . . . .53Slip-On Handrail Fittings . . . . . . . . . .54Handrail Fittings . . . . . . . . . . . . . . . . .58Safety Stair Nosings . . . . . . . . . . . . .59
877-638-6365 toll-free • 877-794-5629 fax
Sales e-mail: [email protected]
P.O. Box 2889, Clackamas, OR 97015
TOLL FREE 1-877-638-6365 TOLL FREE 1-877-638-6365
www.rgpgrates.com www.rgpgrates.com
www.rgpgrates.com
1Introduction
Robertson Grating Products – “The Grate Company”
Robertson Grating Products is the premier grating supplier and fabricator in the USA. Serving grating requirements from the Pacific to the Atlantic, Robertson Grating Products is your one stop location for all steel, aluminum, stainless, and fiberglass grating needs. Our warehouse and fabrication facility is filled with stock material and ready for your grating fabrication needs. RGP can meet the requirements of the largest grating jobs in the industry. Our large stock in grating and handrail components assures you will receive optimal price and service. At RGP, all grating is fabricated according to NAAMM Standards, and the experience of our company guarantees you will receive your grating accurate to specifications at your shop or job site on schedule.
Robertson Grating Products can help you with bar grating, plank grating, fiberglass grating, handrail fittings, American Safety Tread, PolyDrain, perforated metals, woven wire, expanded metal, and more.
Serving grating requirements from the Pacific to the Atlantic, Robertson Grating Products is your one stop location for all steel, aluminum, stainless, and fiberglass grating needs.”
“
877-638-6365
2 Steel Bar Grating
19W4 & 19W2 Bearing Bars at 1-3/16" O.C.
Available Spacings
Bar Size Weight Per Sq. Ft. (lbs)
Conversion TableThe loads shown are for type 19-4 and 19-2 gratings. To determine the load carrying capacity for alternative bar spacings, multiply the loads given by the following conversion factors (deflection remains constant)
Types 15-4 & 15-2: 1.27 Types 11-4 & 11-2: 1.70 Types 7-4 & 7-2: 2.50
3/4"x1/8"
3/4"x1/16"
1"x1/8"
1"x3/16"
1-1/4"x1/8"
1-1/4"x3/16"
1-1/2"x1/8"
1-1/2"x3/16"
1-3/4"x3/16"
2"x3/16"
2-1/4"x3/16"
2-1/2"x3/16"
Note: Cross bars typically extend 1/8" each side of panel. Panel widths do not include these extensions.
www.rgpgrates.com
3Heavy-Duty Steel Bar Grating
Heavy-Duty Steel bar Grating Type 19W4 and 19W2
NOTE: 5/16" or 3/8" heavy weld sizes also available. Contact Robertson Grating Products
Panel Widths
877-638-6365
4 Wheels n’ Heels® Grating
Heavy Duty Steel GratingA type of heavy-duty welded steel grating which satis-
fies both the vehicle loading requirements of AASHTO and the pedestrian comfort requirements of the Americans with Disabilities Act. The Long Span Series may be speci-fied as serrated or a slip-resistant surface may be applied to either type of grating. Wheels n’ Heels® is ideal for parking garages, sidewalks, and pedestrian accessible roadways where ventilation or drainage is required.
Construction: WeldedMaterial: Plain Steel
Mill Finish, galvanized, or standard black paint
Heights: 1", 1-1/4", 1-1/2", 1-3/4", 2" (short span), 2-1/2", 3", 3-1/2", 4", 4-1/2", 5" (long span)
Bar Thickness: 1/4"Bar Spacing: 1/2" (8-WH-4) or 3/4" (12-WH-4)
(short span), 15/16" (15-WH-4), or 1-7/16" 23-WH-4) with 3/16" filler bars on same centers (long span)
Lengths: 3' (short span) 8' (long span)
Specifications
Short Span
Short Span
Long Span Plain Surface
Long Span Serrated Surface
Long Span Serrated Surface
Long Span Plain Surface
www.rgpgrates.com
5Aluminum Bar Grating
Swage-Lock Rectangle Bar
Swage-Lock Serrated
Aluminum grating used as sun-screen over entry-way.
Swage-Lock Flush Top
I-Bar
877-638-6365
6 Grating Stair Treads
Aluminum TreadsRectangular Bars
Steel Treads
Note: When tread length exceeds 5'-6" (1.67m), design tread for 300lb (1.33kN) concentrated loads at one-third points.
Dimension Ain details above– in. (mm)
Stair Tread with Checkered Nosing
Stair Tread with Abrasive Nosing
Stair Tread with Corrugated Nosing
Single JawGalvanized, or
316-stainless steel
Countersunk Land Anchor Block Saddle Clip Galvanized, or
316-stainless steel
G-Clip Clamp Galvanized, or
316-stainless steel
Grate-Fast Pultruded Fiberglass Clip 316-stainless steel
Anchor Devices
GT-WGalv., carbon steel, or 316-stainless steel clip
GT-RGalv., carbon steel or
316-stainless steel clip
SSGT-X316-stainless steel clip
SSGT-F316-stainless steel clip
for pultruded, fiberglass grating
SSGT-Y316-stainless steel clip
for 1-1/2" sq. mesh, molded fiberglass
SSGT-Z316-stainless steel clip
for 2" sq. mesh, molded fiberglass
www.rgpgrates.com
7Safety Grating
Riveted Bar Grating
First choice of many engineers
Greater load carrying capacity
Recommended in difficult stress situations
Increased resistance to buckling and shuttering
Smoother surface for vehicular traffic.
High strength and stiffness to weight ratio
Unparalleled when rolling stock is used
Use as flooring, ramps, docks, etc.
•
•
•
•
•
•
•
•
Note: Riveted grating marking indicates space between bearing bars.Note: Dimensions inside face to inside face of bearing bars.
Slip-Not® Safety Grating
Choice of Steel Or Aluminum
Designed using the truss style
Each rivet is individually cold-pressed
Reticuline bars are sealed together
Open mesh or close mesh is available
On special order, heavy-duty bar sizes and/or widths greater than shown are also available.
•
•
•
•
•
Serrations For Safety
Lower installation costs
Maximum openness
Better drainage
Maintenance-freeContact Robertson Grating Products for more information regarding design and specifications.
•
•
•
•
Riveted Bar Grating
877-638-6365
10 Bar Grating Standards
General Recommendations for Grating InstallationGrating shall be installed with cross bars on top side to obtain the strength characteristics as indicated.
Metal shall be used for all grating supports
A minimum of 1 in. (25mm) shall be provided
www.rgpgrates.com
11Bar Grating Standards
Manufacturing Tolerances
NOTE:
All manufacturing, fabrication, welding, and tolerances shall comply with the NAAMM Metal Bar Grating manual designated ANSI/NAAMM MBG 531 (current edition).
877-638-6365
12 Bar Grating Standards
Manufacturing TolerancesAll tolerances indicated are maximum permissible values
www.rgpgrates.com
13Aluminum Plank
Plank Punch/Pattern AvailabilityAluminum plank grating is available unpunched or with
a variety of punch/patterns as shown below. Rectangular or square punched holes are most commonly used for water and waste treatment plants and in marine applica-tions, while the round holes find application primarily in
the marine market. The surface of plank grating can be specified as plain or with one of two styles of upsets (OGI or WACO) designed to promote a slip resistant walkway, especially in the pres-ence of moisture, oil or other spilled substances.
Note: Plank is also available in a Dog-Bone punch pattern by special request. Contact Robertson Grating Products.
Section AvailabilityPunch/Pattern Availability
877-638-6365
14 Aluminum Plank
Plank Load Tables
* Based on punched plank
Note: Grating for spans to the left of the heavy line have a deflection less than 1/4" for uniform loads of 100 lbs./sq. ft. This is the maximum deflection to afford pedestrian comfort and can be exceeded for other types of load at the discretion of the engineer. The actual Ped (pedes-trian) Span under this condition is shown above for each size of grating. This grating conforms to MIL-G-18015 (SHIPS).
www.rgpgrates.com
15RGP Molded Fiberglass Grating
Molded Fiberglass GratingRGP Molded Fiberglass Grating is available in both high-quality polyester (standard) and vinyl ester resin for harsher
chemical applications. Our high-traction grit surface is standard, but meniscus (concave/non-grit) is available upon request. Molded comes standard in gray and green. Other colors such as yellow and orange are available upon request. Contact Robertson Grating Products for details.
Maximum load represents a 5:1 factor of safety on Ultimate Load Capacity
Ultimate Load Capacity represents failure of the grating (failure defined as a significant drop in load carrying capability of the grate
Above load and deflection data are from actual test data gathered in US. Test was conducted in ambient temperatures.
The load and deflection data provided above are intended as guidelines only, to help determine proper grating size for the application. Changes of resin system, surface, and environment may alter loading data. We cannot be responsible for the performance of the grating under different conditions.
•
•
•
•
Depth 1" 1-1/2" 2"Sq. Mesh 1-1/2" 1-1/2" 2" Panel Size 3' x 10' 3' x 10' 4' x 12' 4' x 8' 4' x 8' 4' x 12' 5' x 10'Wt./Sq. Ft. 2.5 lbs 3.9 lbs 4.7 lbsOpen Area 69% 69% 71%
Concentrated Load Uniform Load
877-638-6365
16 Pultruded Fiberglass Grating
Style I-4010
Style I-6010
Pultruded I-Bar SeriesPultruded fiberglass grating has the great corrosion resistant attributes of our popular molded grating, but with its higher
percentage of glass, gives a higher unidirectional strength and stiffness. It is available in both polyester and vinyl resins with both gray and yellow available. Pultruded is easy to install and its durable grit surface will give your walkway added safety.
Standard Features:
Polyester resin standard. Vinyl ester available.
Available colors: gray and yellow
Durable grit surface
Cross-bar spacing: 6" on-center
Standard panel size: 4'x12'NOTE: Custom lengths, colors, bar spacings, and finishes are available. Contact RGP for details.
•
•
•
•
•
www.rgpgrates.com
17Pultruded Fiberglass Grating
Style T-1800T-1800 is commonly used in applications where close spacing between T-bars is critical for foot traffic comfort. Typical ap-
plications include trenches around swimming pools and decking. Light gray is common color. Light grit is standard for foot comfort.
1" T-1800Bars/Ft. 8Load Bar 1"Open Area 18%Approx. Wt. 2.86 lbs/sq. ft.
Style I-4015
Style I-6015
T-1800 Detail
877-638-6365
18 RGP Plate & RGP Covered Grating
RGP Plate and RGP Covered Grating
RGP Plate–Available in Grit Surface or Smooth Surface
RGP Covered Grating–Grit Surface
RGP Covered Grating–Smooth Surface
RGP Plate and RGP Covered Grating is perfect for applications requiring both a solid floor and corrosive resistance that fiberglass provides. Both are available in polyester and vinyl ester resins. RGP Plate comes available in thicknesses from 1/8" to 3/4". Please specify grit surface for traction or smooth top. RGP Covered Grating is like RGP Molded Grating with 1/8" fiberglass plate affixed to top. Popular panel size for both products is 4' x 8'.
RGP Stair TreadRobertson Grating Products has the stair tread you
need for high-traction performance, and since it's made of our high-quality resins, its built to last in harsh environ-ments. Order our stair tread panels or give RGP dimen-sions and quantities for pricing on your job fabricated to size. Colors green and gray are standard with grit surface and black nosing.
1-1/2" Thick, 1-1/2" x 6" MeshOpen Area 70%Approx. Wt. 4.66 lbs/sq. ft.
RGP Stair Tread Detail
Specifications
Material: Pultruded fiberglass reinforced poly-ester plate with anti-skid grit surface
Thickness: 1/8", 3/16", 1/4", 3/8", 1/2", 3/4"Size: 4' x 8' panelsResin: Polyester, vinyl esterColor: Gray standard, green, orange,
yellow, and other colors available upon request.
Surface: Grit or smooth surfaceResin information available. Contact RGP for details.
www.rgpgrates.com
19RGP Structural Fiberglass & Hardware
RGP Structural Fiberglass
Single Jaw I-615 Clip
I-610 Clip
I-415 Clip
I-410 Clip
SSGT-F For pultruded, fiberglass grating
SSGT-Y For 1-1/2" sq. mesh, molded fiberglass grating
SSGT-Z For 2" sq. mesh, molded fiberglass grating
Equal Leg Angle
Channel I-Beam Embedment Angle
Solid Rod
Round Tube
Square Tube
Wide Flange I-Beam
Many sizes available. Contact RGP for details.
Clip Assemblies for Molded and Pultruded Grating and PlateRGP offers specially-designed attachments and clips, both to fasten panels together and to secure them to support struc-
tures. All types are made of Type 316 stainless steel and are available in 1", 1-1/2" and 2" sizes. Install clips a maximum of every 48" and use at least four clips per piece of grating (at least eight clips per 4' x 12' panel.)
877-638-6365
20 GRIP-STRUT® Safety Grating
For over 40 years Robertson has teamed with Grip-Strut® to serve their customers nationwide,
Quality products and services are what RGP is all about!
2-Diamond Plank, 4-3/4" width 3-Diamond Plank, 7" width
Allowable loads and Deflections: U–uniform load (lb./ft.2) C–concentrated load (lb.) D–deflection (in.)
Spans to the left of heavy line produce a deflection of 1/4" or less under uniform load of 100 lb./ft.
www.rgpgrates.com
21GRIP-STRUT® Safety Grating
5-Diamond Plank, 11-3/4" width
also in stainless steel
4-Diamond Plank, 9-1/2" width
also in stainless steel
Allowable loads and Deflections: U–uniform load (lb./ft.2) C–concentrated load (lb.) D–deflection (in.)
Spans to the left of heavy line produce a deflection of 1/4" or less under uniform load of 100 lb./ft.
877-638-6365
22 GRIP-STRUT® Safety Grating
8-Diamond Plank, 18-3/4" width
Allowable loads and Deflections: U–uniform load (lb./ft.2) C–concentrated load (lb.) D–deflection (in.)
Spans to the left of heavy line produce a deflection of 1/4" or less under uniform load of 100 lb./ft.
www.rgpgrates.com
23GRIP-STRUT® Safety Grating
10 Diamond Plank, 24" width
10 Diamond Walkway, 24" width
877-638-6365
24 GRIP-STRUT® Safety Grating
Stair Treads Load Data
2-diamond 3-diamond 4-diamond 5-diamond
Steel Gauge 14 12 14 12 14 12 14 12
Span Height U C U C U C U C U C U C U C U C
2'0" 1-1/2" 1191 472 1576 624 761 443 1006 587 549 435 750 595 434 425 575 563
2" 1978 783 2513 995 1262 737 1604 936 911 604 1158 917 721 573 916 897
2"6" 1-1/2" 764 378 1011 500 488 356 645 470 353 3449 481 476 278 342 369 452
2" 1268 611 1611 797 810 590 1029 750 584 578 742 734 463 566 587 719
3'0" 1-1/2" 532 315 703 418 340 300 450 393 245 300 335 398 194 300 258 378
2" 882 524 1121 665 563 492 716 626 407 483 517 614 322 473 409 601
4'0" 2" 498 394 633 501 318 372 404 472 230 364 292 463 182 356 232 454
2 Dia. 3 Dia. 4 Dia. 4 Dia. 5 Dia. 5 Dia.
Material Alum. Alum. Alum. Stainless Alum. Stainless
Gauge 0.80" 0.80" 0.80" 304 0.80" 304
Span Height U C U C U C U C U C U C
2'0" 2" 1328 526 862 503 607 481 610 483 396 388 394 386
2'6" 2" 850 420 551 402 388 392 390 387 253 388 252 381
3'0" 2" 590 350 383 335 270 327 271 323 176 321 175 319
4'0" 2" 332 263 215 252 152 245 152 244 99 241 98 241
Intermediate stringer is recommended for spans over 4'
Load data below takes eccentric loads into consider-ation. Although load values include allowances for normal impact conditions and usual pedestrian traffic, be sure to make provisions in the structural design for special uses and loads involving unusual impact forces or vibratory forces. Load-carrying capacity of stair treads increases as side channel height and gauge of material increase.
www.rgpgrates.com
25GRIP-STRUT® Safety Grating
Standard Tread
Tread with Abrasive Nosing
Grip-Strut Stair Treads Product Data
Steel, Aluminum, and Stainless Steel
Standard W/ Abrasive Nosing
A B C D A B C D
4-3/4" 1-1/2" 3/4" 2-5/8" — — — —
(2 dia.) 2" 1" 2-5/8" — — — —
7" 1-1/2" 3/4" 3-3/8" 8-1/8" 1-1/2" 3/4" 4-1/2"
(3 dia.) 2" 1" 3-3/8" (3 dia.) 2" 1" 4-1/2"
9-1/2" 1-1/2" 3/4" 5-7/8" 10-1/2" 1-1/2" 3/4" 6-7/8"
(4 dia.) 2" 1" 5-7/8" (4 dia.) 2" 1" 6-7/8"
11-3/4" 1-1/2" 3/4" 8-1/8" — — — —
(5 dia.) 2" 1" 8-1/8" — — — —
NOTE: Stainless steel not available in 2 and 3 diamond widths.
A, B, C, and D dimensions have a tolerance of +/- 1/16"
Heavy Duty Grip-Strut
Material
Steel 10 gauge (mill galvanized before fabrication ASTM A525
Steel 9 & 11 gauge special order–contact RGP
Black (unpainted and oiled steel) 10 gauge
Widths
Plank: 9-1/4", 13-3/4", 23-1/4", 27-3/4", 36"
Walkway: 24", 30", 36"
Heights
Plank: 2", 2-1/2", 3". 4"
Walkway: 5" depth
Lengths
10' or 12' stock lengths or cut-to-size
Open area: 52%
•
•
•
•
•
•
•
•
Compliance with regulatory codes/standards/tested performance
Walkways meet OSHA toeboard requirements for elevated structures, with upturned 5-in. high integral side channels. Statistics show falls as the second highest cause of lost-time injuries in industry. Yet tests prove that falls can be reduced by the safe surface of Heavy Duty GRIP STRUT® Safety Grating.
Heavy Duty Stair Tread Load Table Load Clear SpanMaterial Height #/LF Cat. # Type 2'0" 2'6" 3'0" 4'0"Steel- 2” 7.4 HT-22010 U 2412 1544 1026 62910 ga. C 1860 1487 1240 929
Heavy Duty Stair Treads
877-638-6365
26 GRIP-STRUT® Safety Grating
Heavy Duty Plank Heavy Duty Walkway
Heavy Duty Plank Detail = StockDescription Width Height A-Size Material2-Diamond 9-1/4" 2", 3", 4" 15/32" Galv. & Black 3-Diamond 13-3/4" 2", 3", 4" 1/2" Galv. & Black5-Diamond 23-1/4" 2", 3", 4" 13/16" Galv. & Black6-Diamond 27-3/4" 2", 3", 4" 27/32" Galv. & Black8-Diamond 36" 2", 3", 4" 17/32" Galv. & Black
Heavy Duty Walkway Detail = StockDescription Width B-Size Material5-Diamond 24" 1-3/16" Galv. & Black6-Diamond 30" 1-31/32" Galv. & Black8-Diamond 36" 17/32" Galv. & Black
www.rgpgrates.com
27GRIP-STRUT® Safety Grating
Reconditioning MaterialIncrease the safety and traction on worn and unsafe
floors and stairs. Resurface with Grip-Strut Recondition-ing Material (RM). Grip-Strut is the only product that gives 500 wall-to-wall teeth per sq. ft. Down-turned edges allow grating to lie flat and secure over existing flooring. Consult RGP for product specifications. RM products are available on special order in standard materials and sizes.
Ladder Rungs
Construction: Material is a channel with diamonds formed in the web of the channel.
Material: Steel 14 gauge galvanized or plain
Height: Stock 1-1/8"; Reverse diamond 1.625"
Width: Stock 2-1/2"; Reverse diamond 1.625"
Lengths: Stock 12' or cut-to-length; Reverse diamond 23.125"
Weight: 1.13 lbs./ft. steel
Safety Factor: 1.5 (steel)
Grip-Strut Safety Grating Ladder Rungs provide safer, more dependable footing indoors and out, in all weather. Serrated open diamond pattern lets stones, mud, snow, and debris fall through. Even hard ice crumbles underfoot for non-slip footing. Grip-Strut Safety Grating complies with the slip-resistance standards established by Federal Specification RRG-1602D. Contact RGP about loading.
•
•
•
•
•
•
Stock 1-diamond rung shown
Span Height Standard W/ Abrasive Nosing
Steel 14 ga. Cat. # Size Cat. # Size
Up 1-1/2" T-21514 2-dia.–4-3/4" — —
to T-31514 3-dia.–7" T-31514-N 8-1/8"
48" T-41514 4-dia.–9-1/2" T41514-N 10-1/2"
Up 2" T-22014 2-dia.–4-3/4" — —
to T-32014 3-dia.–7" T-32014-N 8-1/8"
48" T-42014 4-dia.–9-1/2" T42014-N 10-1/2"
T-52014 5-dia.–11-3/4" — —
Steel 12 ga. Cat. # Size Cat. # Size
Up 1-1/2" T-21512 2-dia.–4-3/4" — —
to T-31512 3-dia.–7" T-31512-N 8-1/8"
48" T-41512 4-dia.–9-1/2" T-41512-N 10-1/2"
T-51512 5-dia–11-3/4" — —
Up 2" T-22012 2-dia
to T-32012 3-dia.–7" T-32012-N 8-1/8"
48" T-42012 4-dia.–9-1/2" T-42012-N 10-1/2"
T-52012 5-dia–11-3/4" — —
Aluminum .080"
Up T-32012-A 3-dia.–7" T-32012-N 8-1/8"
to T-42012-A 4-dia.–9-1/2" T-42012-N 10-1/2"
36" T-52012-A 5-dia–11-3/4" — —
Stainless Steel - Type 304 - 16 gauge
Up to 2" T-42016-S 4-dia.–9-1/2" — —
36" T-52016-S 5-dia–11-3/4" — —
Standard Sizes & Recommended Spans
Recommendations are based on approximate minimum loads of 300lbs. concentrated; 100lbs. uniform. Specific performance criteria may vary by municipality/building code body and should be locally checked prior to final-izing specifications.
877-638-6365
28 GRIP-STRUT® Safety Grating
Pre-Galvanized Steel-14 Ga.-SerratedFed spec RRG 1602D Type II
Cat. No. Diamond Width Height11014 Rung* 1 2-1/2" 1-1/8"21514* 2 4-3/4" 1-1/2"22014* 2 4-3/4" 2"22514* 2 4-3/4" 2-1/2"31514* 3 7" 1-1/2"32014 3 7" 2"32514 3 7" 2-1/2"41514* 4 9-1/2" 1-1/2"42014* 4 9-1/2" 2"42514* 4 9-1/2" 2-1/2"51514* 5 11-3/4" 1-1/2"52014* 5 11-3/4" 2"52514* 5 11-3/4" 2-1/2"81514* 8 18-3/4" 1-1/2"82014* 8 18-3/4" 2"82514 8 18-3/4" 2-1/2"102014* 10 24" 2"103014* 10 24" 3"104514-U* Walkway 10 24" 4-1/2"
*Stock lengths are 12'. Special lengths available upon request.
Pre-Galvanized Steel-12 Ga.-SerratedFed spec RRG 1602D Type II
Cat. No. Diamond Width Height21512* 2 4-3/4" 1-1/2"22012 2 4-3/4" 2"22512* 2 4-3/4" 2-1/2"31512* 3 7" 1-1/2"32012* 3 7" 2"32512* 3 7" 2-1/2"33012* 3 7" 3"41512* 4 9-1/2" 1-1/2"42012 4 9-1/2" 2"42512* 4 9-1/2" 2-1/2"43012* 4 9-1/2" 3"51512* 5 11-3/4" 1-1/2"52012* 5 11-3/4" 2"52512* 5 11-3/4" 2-1/2"53012 5 11-3/4" 3"81512 8 18-3/4" 1-1/2"82012 8 18-3/4" 2"82512* 8 18-3/4" 2-1/2"83012 8 18-3/4" 3"101512 10 24" 1-1/2"102012* 10 24" 2"103012* 10 24" 3"104512-U* Walkway 10 24" 4-1/2"
Aluminum-.080" Ga.-Type 5052-SerratedFed spec RRG 1602D Type IV
Cat. No. Diamond Width Height22012-A** 2 4-3/4" 2"32012-A** 3 7" 2"42012-A** 4 9-1/2" 2"52012-A** 5 11-3/4" 2"Stainless Steel-16 Ga.-Type 304-SerratedFed spec RRG 1602D Type II
Cat. No. Diamond Width Height42016-S 4 9-1/2" 2"52016-S 5 11-3/4" 2"
Heavy Duty— Please contact RGP
NOTES:
*Also available in “Black” (plain steel)-add “B” to catalog number when ordering.
**Also available in .100” thickness Aluminum-change last 2 digits in cata-log number to “10A” when ordering.
Stock List
Standard lengths 10', 12', or cut-to-size. Special lengths up to 24 feet available. Contact RGP for details.
www.rgpgrates.com
29GRIP-STRUT® Safety Grating
Anchor and Clamp AssembliesClamp prevents grating from shifting on supports. Holds
pieces together with or without clearance between panels. All bolts are below top surface of grating. No holes are drilled in supporting members.
Assembly consists of anchor plate, 2 J-bolts, nuts, and washers, all hardware is electro zinc plated. The anchor plate is hot dip mill-galvanized before fabrication. Op-tion: anchoring device can be cadmium plated on special order. Call RGP for details.
Height Catalog# Height Catalog#
1-1/2” ACA-15 2” ACA-20
2-1/2” ACA-25 3” ACA-30
Anchoring Device ClipDiamond anchor catalog #12262 is shaped to fit in dia-
mond opening. Punched to receive 5/16" carriage head bolt with square shank. Does not include bolts, nuts, or washers.
Rooftop Walkways
Roof performance–protects membrane, optimizes roof performance by:
Saving roof from abuse of walking and equipment
Minimizing abrasion, walkway pressures on membrane (large rubber pads distribute support-stand loads)
Relieving membrane thermal stresses (no fasteners, low bearing stress permit membrane movement)
Maximizing direct, free-flow drainage (elevated planks, open supports, waffle pads)
Preserving membrane integrity
Versatility–designed for all roofing systems: built-up (BUR), single-ply (SPR), inverted, and spray-on
Economy–long life, low maintenance on roof and walk-way
•
1.
2.
3.
4.
5.
•
•
Benefits of Grip-Strut Rooftop Walkways:
Flat Stock Grip-Strut: Special OrderThe open matrix is symmetrical about the flat plane.
Table indicates the approximate dimensions of flat metal available on each side. Flat stock can also be manufac-tured to specified dimensions of flat metal on either or both sides. Please call RGP for specifications and avail-ability. Flat stock is available in all standard materials and sizes.
Dimensions for Steel And Aluminum
Matrix Flat metal each side
2-diamond 2-1/4" to 7-1/2"
3-diamond 2-1/8" to 6-1/2"
4-diamond 2-3/8" to 7-5/8"
5 diamond 2-3/8" to 6-1/2"
8-diamond 2-3/8 to 5-5/8"
10-diamond 3-1/4 to 7-5/8"
877-638-6365
30 GRIP-STRUT® Safety Grating
Walkway Splice Plate Kits
Splice Plate Kit 30" Part No. SP-10DU-30
Four 9/16" dia. holes staggered in each corner of up-turned kickplate, two 8-hole, 12 ga. 4-1/2" x 30" C-channel splice plates with 16 ea. 1/2" x 1-1/4" hex head cap screws (galv. S.A.E. Grade 5, lightly oiled), washers and hex nuts. Kit joins continuous sections together in run over clear spans to act as one continuous unit. Any com-bination of 12 and 10 ft. planks can be joined with splice plate package.
Splice Place Package 7" Part No. SP-10DU-7
Four 1/2" dia. holes in each corner of up-turned kick-plate, two 8-hole 10 ga. 4" x 7" splice plates, with 16 ea. 7/16" x 1-1/4" bolts, washers and hex nuts. Each corner of up-turned kickplate should have four 1/2" dia. holes. Kit joins continuous sections together in a run only over sup-ports. Recommended bolt torque: 55 ft./lb. minimum.
Walkway Splice plates are also available for Heavy Duty Grip-Strut– contact RGP for details.
Recommended clearance
STEEL: 1/4" minimum is recommended at perimeter and 3/8" maximum at end joints. maximum between panels is 1/4". 1/8" is generally used.
CONCRETE: Concrete form deflection calls for slightly greater perimeter clearance. 1/2" is recommended. Maxi-mum between panels 1/4".
Bearing Surfaces
Recommended minimum bearing 1-1/2". Surfaces sup-porting Grip-Strut must be smooth and level to insure that adjoining sections provide a safe, even walking surface.
Permanent Installation
Grip-Strut is easily welded to supports for permanent in-stallations. Channels are quickly welded together between supports to provide uniform deflection in adjacent panels.
For welded attachment, secure side channels to sup-ports by fusion welding with 1/8" fillet welds. Weld adja-cent planks together with 1/8" fillet welds 1" long, 24" o.c. staggered top and bottom.
Install Grip-Strut according to details as shown on indi-vidual job drawings or as follows:
1.) Single width applications: Utilizing the anchoring device or weldings, attach Grip-Strut plank at every point of contact with supporting structure around perimeter of plank.
2.) Multiple width applications: Utilizing the Grip-Strut anchoring device or welding as recommended by A.I.S.I. attach plank around the perimeter at each point of contact with supporting structure. In field, attach plank to support-ing structure with a minimum of one attachment at each end of plank on alternate sides. When span exceeds 8 ft., weld or bolt side channels of adjacent planks together at midpoint of span. (When spans exceed 6 ft., consider similar treatment.)
General Installation Recommendations
www.rgpgrates.com
31PERF-O GRIP® Grating
PERF-O GRIP® 2-Hole Plank – 5" Width
PERF-O GRIP® Safe Loading Tables
Every year industrial accidents – falling, tripping over debris, slipping on wet or greasy surfaces – cost millions of dollars in lost man-hours and production. Insurance costs often are reduced when accident rates decline. PERF-O Grip Grating and Traction Tread Flooring help cut accident rates by providing safer walking-working surfaces.
Main Features of PERF-O GRIP:
Safe surface
Long life
Fast installation
Economical to install and use
Versatile in application
•
•
•
•
•
U = Allowable Uniform Load (lbs/ft2)
C = Allowable Concentrated Load (lbs.) applied by 2" round bar across full width of grating
D = Vertical Deflection (inches) of side channels at mid span resulting from Allowable Load.
•
•
•
U = Allowable Uniform Load (lbs/ft2)
C = Allowable Concentrated Load (lbs.) applied by 2" round bar across full width of grating
D = Vertical Deflection (inches) of side channels at mid span result-ing from Allowable Load.
P-Bolt Seat – Standard
877-638-6365
32 PERF-O GRIP® Grating
PERF-O GRIP® 3-Hole Plank – 7" Width
PERF-O GRIP® 5-Hole Plank – 10" Width
U = Allowable Uniform Load (lbs/ft2)
C = Allowable Concentrated Load (lbs.) applied by 2" round bar across full width of grating
D = Vertical Deflection (inches) of side channels at mid span resulting from Allowable Load.
U = Allowable Uniform Load (lbs/ft2)
C = Allowable Concentrated Load (lbs.) applied by 2" round bar across full width of grating
D = Vertical Deflection (inches) of side channels at mid span resulting from Allowable Load.
www.rgpgrates.com
33PERF-O GRIP® Grating
PERF-O GRIP® 6-Hole Plank – 12" Width
PERF-O GRIP® 10-Hole Plank – 18" Width
U = Allowable Uniform Load (lbs/ft2)
C = Allowable Concentrated Load (lbs.) applied by 2" round bar across full width of grating
D = Vertical Deflection (inches) of side channels at mid span resulting from Allowable Load.
U = Allowable Uniform Load (lbs/ft2)
C = Allowable Concentrated Load (lbs.) applied by 2" round bar across full width of grating
D = Vertical Deflection (inches) of side channels at mid span resulting from Allowable Load.
877-638-6365
34 PERF-O GRIP® Grating
PERF-O GRIP® 13-Hole Plank – 24" Width
PERF-O GRIP® 16-Hole Plank – 30" Width
U = Allowable Uniform Load (lbs/ft2)
C = Allowable Concentrated Load (lbs.) applied by 2" round bar across full width of grating
D = Vertical Deflection (inches) of side channels at mid span resulting from Allowable Load.
U = Allowable Uniform Load (lbs/ft2)
C = Allowable Concentrated Load (lbs.) applied by 2" round bar across full width of grating
D = Vertical Deflection (inches) of side channels at mid span resulting from Allowable Load.
www.rgpgrates.com
35PERF-O GRIP® Grating
PERF-O GRIP® Walkway – 24" and 30" Widths
PERF-O GRIP® Grating Splice Plate Kits
U = Allowable Uniform Load (lbs/ft2)
C = Allowable Concentrated Load (lbs.) applied by 2" round bar across full width of grating
D = Vertical Deflection (inches) of side channels at mid span resulting from Allowable Load.
Walkway Splice Plate Kits
Walkway Splice Plates provide continuity when multiple lengths of PERF-O GRIP are desired. Connections are reinforced with the addition of splice plates attached to side channels.
POG-WS-30 for 24" and 30" wide walkway
Each kit includes 2 splice plates and 32 each of the following hardware: 1/2" x 1-1/4" hex bolts, 1/2" 13 hex nuts and 1/2' flat washers.
•
•
Surface Splice Plate Kits
As width increases, grating surface performance becomes more critical. Thus, for PERF-O GRIP product widths greater than 12", use of grating splice kit is recom-mended to mechanically join butt ends of plank sections.
POG-ES-10 for 18" wide plank includes 6 each of hard-ware shown below
POG-ES-13 for 24" wide plank includes 6 each of hard-ware shown below
POG-ES-30 for 30" wide plank includes 8 each of hard-ware shown below
Hardware included: 3/8" x 1 carriage bolts, 3/8" flat washers and bolt seats
•
•
•
•
877-638-6365
36 PERF-O GRIP® Grating
PERF-O GRIP® Grating Stair Treads and Carrier Plates
PERF-O GRIP® Grating Mid-Clip Support Clips
Stair treads and carrier plates are available in mill-gal-vanized and hot rolled, pickled and oiled (standard), but may be ordered in aluminum or stainless steel. Contact RGP for details.
PERF-O GRIP midsupport clips can be used at mid-span to increase load carrying capacities of individual channels by fastening several planks together to form and integral section. Mid Clip is manufactured from galvanized steel and includes two bolts.
Stair Treads – Standard
PERF-O GRIP Stair Treads have welded end-caps for attachment to stringers.
Mill galvanized steel, 11-gauge & 13 gauge
Hot-rolled, pickled and oiled carbon steel, 11-gauge & 13-gauge
24", 30", and 36" lengths
5", 7", 10" & 12" (nominal) widths
1-1/2" and 2" channel heights
•
•
•
•
•
Stair Treads – Custom
PERF-O GRIP Stair Treads are also available with TRACTION-TREAD leading edge nosing.
Mill galvanized steel, 11-gauge & 13 gauge
Hot-rolled, pickled and oiled carbon steel, 11-gauge & 13-gauge
24", 30", and 36" lengths
12" (nominal) width
1-1/2" and 2" channel heights
•
•
•
•
•
www.rgpgrates.com
37TRACTION TREAD™ Flooring
TRACTION TREAD™ Flooring and PlankTRACTION TREAD Flooring, Planks, and Ladder Rungs feature a surface with hundreds of perforated buttons that provide
slip-resistance in all directions making it a practical choice for industrial applications. TRACTION TREAD is also appropriate for commercial applications where pedestrian traffic is a consideration, perfectly suited for ADA-compliant requirements.
TRACTION TREAD is easily adapted for a multitude of applications, offering a safe walking-working surface for walkways, ramps, stair-treads, and equipment platforms. TRACTION TREAD is ideal for the manufacture of special and fabricated prod-ucts, and is often used as a reconditioning material over existing surfaces that do not provide slip-resistance.
TRACTION TREAD Flooring is available in stock sheets designed for secondary fabrication requirements.
Material Options
Hot-rolled, pickled and oiled carbon steel: 11-gauge (5.0 lb. / sq. ft.) 13-gauge (3.8 lb. / sq. ft.) 16-gauge (2.5 lb. / sq. ft.)
Aluminum alloy 5052-H32 .125" (1.6 lb. / sq. ft.)
Sheet Size
Standard 36" x 120"
Cut to order
•
•
•
•
Material Options
Hot-rolled, pickled and oiled carbon steel: 11-gauge and 13-gauge
Mill-galvanized steel: 11-gauge and 13-gauge
Plank Dimensions
7", 10" and 12" widths (nominal)
120" or 144" lengths (nominal)
1 1/2" (min.) or 2" (standard) channel height
•
•
•
•
•
TRACTION TREAD Plank TRACTION TREAD Ladder Rungs
2-Hole ladder Rung
Hot-rolled, pickled and oiled carbon steel: 13-gauge (1.2 lb. / lf)
Aluminum alloy 5052-H32: .125 (0.5 lb. / lf)
1-1/4" W x 1-1/2" H x 48" or 60" length
3-Hole Ladder Rung
Hot-rolled, pickled and oiled carbon steel: 13-gauge (1.2 lb. / lf)
Aluminum alloy 5052-H32: .125 (0.5 lb. / lf)
1-5/8" W x 1-1/8" x 48" or 60" length
4-Hole Ladder Rung
Hot-rolled, pickled and oiled carbon steel: 13-gauge (1.2 lb. / lf)
Aluminum alloy 5052-H32: .125 (0.7 lb. / lf)
1-5/8" W x 1-1/8" H x 48" or 60" length
•
•
•
•
•
•
•
•
•
NOTE: Specifications shown are for standard products. Contact RGP for details.
877-638-6365
38 GRATE LOCK® Grating
GRATE-LOCK Grating
GRATE-LOCK Grating is an easy-to-install system of interlocking grating planks, treads and accessories that provides safe, sturdy footing for mezzanine floors, platforms, walkways, and other applications where non-slip performance is required. Hundreds of sole-gripping dimples ensure a safe surface in all kinds of weather and environments. The grating is available for safer working surfaces, non-textured for wheeled traffic or rack decking.
Cost-saving design
Wide range of sizes and accessories
Fast field assembly
Traction grip and plain surfaces
Choice of two gauges: 14 and 18
•
•
•
•
•
GRATE-LOCK Non-Slip Grating System Components - Plank Sections
GRATE-LOCK Non-Slip Grating System Accessories
www.rgpgrates.com
39GRATE-LOCK® Grating
GRATE-LOCK Grating - 1-1/2" Channel Height
GRATE-LOCK Grating - 2-1/2" Channel Height
Product Design and Selection Table
877-638-6365
40 GRATE-LOCK® Grating
GRATE-LOCK Grating - 3" Channel Height
Product Design and Selection Table
GRATE-LOCK Grating - 4" Channel Height
Product Design and Selection Table
www.rgpgrates.com
41Pre-Shaped Trench Drain
Robertson Pre-Shaped Trench Drain System
Drain Covers Typical PolyDrain System
Catch Basin
#502 Ductile Iron Grate
#503 Ductile Iron Grate Class E
#420 Galv. Slot Grate
#410 Perforated Grate
#422 Reinforced Galv. Grate
877-638-6365
42 Drainage Trench Solutions
Trench Grating
Robertson Grating Products provides high-quality trench side frames, grates, and solid cover castings. From pedestrian areas to loading ramps at airports, Robertson Grating Prod-ucts has the trench drainage solution to fit your application.
Standard heavy duty grates and covers are suitable for general traffic service and AASHTO H-20 loading conditions. (Our ADA style trench grating and solid trench covers are available for general traffic loading in addition to non-traffic application.) Extra heavy duty airport trench grating is made with ductile iron and is proof load tested to 200,000 pounds.
Type M2 Type M1/B1 Type M2
Type P, ADA Type A Solid Cover
Grating options include
parallel gratings,
perpendicular cross-street drainage
ADA styles,
available in 24" lengths
widths from 8" up to 51".
Frames come in 24", 36" and 48" lengths.
non-bolted units
bolted assembly.
For your convenience bolted grating and rail units are assembled in 24" length sec-tions using four stainless steel hex head bolts.
•
•
•
•
•
•
•
•
When ordering trench products, please specify:1. Width of trench opening, dimension "A"
2. Seat depth, dimension "B"
3. Clear opening of trench, dimension "C"
4. Length of trench installation
5. Type of grate or solid cover
6. Are side frames required?
7. Are grates/covers bolted to the frames?
8. Load requirement
www.rgpgrates.com
43Foundry Castings
6900 & 6950 Trench Grate Series
6970 Trench Assembly
V-7380 Trench Grate Series, ADA
Heavy Duty
Standard trench grates available in: 23-7/8" lengths
Frames available in 24", 36" and 48" lengths.
Bolted trench grate units assembled in 24" sections.
Specify trench length and part number of desired trench width.
Solid cover available
•
•
•
•
•
•
Heavy Duty
Available in 18" and 36" assemblies
•
•
Bolted 24" assembly
Standard Trench
ADA compliant
Bolted or unbolted
Standard 3/8" slot openings for safety
Grates available in standard 24" lengths
Frames available in 24", 36", and 48" lengths
Specify trench length and part number of desired trench width
•
•
•
•
•
•
877-638-6365
44 Perforated Metal
Perforated Metal – Standard Patterns Available
Steel, Aluminum, Stainless, Copper, and Brass
Specify quantity and dimensions of sheets, pieces, or panels.
Indicate gauge and kind of material. Specify thickness in decimals
Specify size, shape, arrangement, and center of holes. If slotted, indicate whether they run lengthwise or crosswise of the sheets.
Specify widths of all margins.
If mounting holes are used, give size and locations on margins.
Indicate special shipping instructions. Unless otherwise indicated, we ship by motor freight. If shipped by rail, please give specific shipping instructions.
When custom panels, screens, or other non-standard items are required, send exact specifications.
For clarification, submit sketch or print.
1.
2.
3.
4.
5.
6.
7.
8.
How To Order Perforated Metal
www.rgpgrates.com
45Woven and Welded Wire
Wire Weaves
How To Order
Aggregate screens and industrial wire cloth. In order to eliminate costly errors and delays, include the following information when ordering.
Quantity: Number of pieces or rolls.
Width: Expressed in inches or fractions thereof. Width should always be specified first.
Length: Finished overall length.
Opening or mesh:
A. Square opening: Specify fractional or decimal space required
B. Slotted opening: Specify fractional or decimal space required in both width and length of opening
Note: When ordering slotted openings specify which direction long opening is parallel to.
C. Mesh: Specify number of openings, counting from center of any wire to a point one inch distant.
Wire size: Expressed in decimals of an inch or W&M gauge number.
Type of material: Specify type of wire cloth– high car-bon spring steel, oil tempered spring steel, stainless steel, etc.
1.
2.
3.
4.
1.
2.
877-638-6365
46 Expanded Metal
Expanded Metal
How To Order Expanded Metal
Specify the size of the sheet required, listing SWD first. Example: 4'-0 SWD x 8'-0 LWD
Specify the number of sheets or pieces required.
Specify the nominal width of the diamond SWD. Example: 1/4", 1/2", 3/4", 1", 1-1/2", 2"
Specify the style of the sheet. Example: #20, #18, #16, #13, #9
Specify R (raised), F (flattened)
Note:
Specify the type of metal required. Example: Carbon steel, stainless steel, Aluminum, etc.
Example of typical order:
100 sheets, 3/4", #9F, 4'-0" SWD x 8'-0" LWD steel
Another example:
40 sheets, 1/2", #16R, 4'-0" LWD x 8'-0" SWD steel
1.
2.
3.
4.
5.
www.rgpgrates.com
49Handrail Fittings
Snap-On Bracket Cover
Cast Handrail Bracket
Traditional Cast BracketsSnap-on cover for concealed mounting of single-hole
formed brackets. Two- and three-hole brackets must be countersunk to use these covers.
Universal Weld Bracket
www.rgpgrates.com
51Handrail Fittings
Coped Drive-On Connectors
Available for steel, aluminum, and stainless steelNo chamfering necessaryAligns pipe and tube prior to weldingSave up to 50% on shop and field welding and finishing costsSaves grinding time
To use:Place connector in each end of pipe or tube until it makes contact with wedge-lock's ribs.Insert wedge into groove of wedge-lock and hammer into place.Wedge-lock will expand against material wall to properly lock and align pipe or tube.Weld the joint solid and grind smooth.
•••••
1.
2.3.
4.
Wedge-Lock™ Welding Connectors
For pipe and round tubing
877-638-6365
52 Post Caps & End Caps
Post caps Type C Weld-On Endcaps
Type D Flat Weld-On Disks
Type A Drive-On Endcaps
www.rgpgrates.com
53Caps & Flanges
Type E Flat Drive-On Disks
Type F Dished Weld-On Caps
Flat Base Flanges
877-638-6365
54 Slip-On Handrail Fittings
Aluminum Slip-On Fittings by Hollaender
Hollaender has evolved into a complete structural pipe fitting provider. Our advanced production and engineer-ing capabilities enable us to create complete handrail systems from design, through manufacture to delivery. Hollaender’s dedication to quality workmanship has car-ried through our products and services for over 75 years.
Fast and easy to install
Reusable heavy duty cast fittings
Complete systems and flexible solutions
Technologically advanced manufacturing
•
•
•
•
#3 Elbow #3AE Elbow #5 Tee
#5E Tee-E #6 Angle Tee (45°)
#7 Offset Cross
#7E Cross-E #9 Side Outlet Elbow
#10 Cross
#11 Side Outlet Tee
#11E Side Outlet Tee-E
#12 Short Barrel Outlet Cross
#13 Side Outlet Cross
#13E Side Outlet Cross-E
#16 Bolt-on Tee
1-1/4", 1-1/2" 1-1/4", 1-1/2" 1-1/4", 1-1/2"
1-1/4", 1-1/2" 1-1/4", 1-1/2" 1-1/4", 1-1/2"
1-1/4", 1-1/2" 1-1/4", 1-1/2" 1-1/4", 1-1/2"
1-1/4", 1-1/2" 1-1/4", 1-1/2" 1-1/4", 1-1/2"
1-1/4", 1-1/2" 1-1/4", 1-1/2" 1-1/4", 1-1/2"
www.rgpgrates.com
55Slip-On Handrail Fittings
Aluminum Slip-On Fittings by Hollaender
#17 Adj. El/Tee
#17EM Adj. El/Tee-Male
#19 Adj. Cross Assembly
#19M Adj. Cross-Male
#20 Outside Corner
#21-35/45 Adj. Cross
#23 Adj. Tee/Cross
#25 Side Outlet Adj. El/Tee
#27 Dbl. Adj. Side Outlet El/Tee
#27M Dbl. Adj. Side Outlet El/Tee
#30 Adj. Cross
#30A Modified Cross
#30B Swivel #30C Adj. Swivel
#40* Triangular Floor Flange
1-1/4", 1-1/2" 1-1/4", 1-1/2" 1-1/4", 1-1/2"
1-1/4", 1-1/2" 1-1/4", 1-1/2" 1-1/4", 1-1/2"
1-1/4", 1-1/2" 1-1/4", 1-1/2" 1-1/4", 1-1/2"
1-1/4", 1-1/2", 2" 1-1/4", 1-1/2" 1-1/4", 1-1/2"
1-1/4", 1-1/2", 2" 1-1/4", 1-1/2" 1-1/4", 1-1/2"
877-638-6365
56 Slip-On Handrail Fittings
Aluminum Slip-On Fittings by Hollaender
#41* Adj. Bracket
#42 Round Base Flange
#43* Round Bracket
#45 Sq. Floor Flange
#45SBC Sq. Floor Flange
#46 Base Flange
#46 ADJ Adj. Flange
#47 Rect. Floor Flange
#48 Flange
#49 Toe Board Bracket Flange
#49C Toe Plate Bracket
#50 Wall Mount Flange
#52 H.D. Wall Flange
#52E Extruded H.D. Wall Flange
#54-3/4/5 Off. Wall Flange (3", 4", 5")
1-1/2" 1-1/4", 1-1/2" 1-1/2"
1-1/4", 1-1/2" 1-1/2" 1-1/4", 1-1/2"
1-1/2" 1-1/4", 1-1/2" 1-1/2", 2"
1-1/4", 1-1/2" 1-1/2" 1-1/4", 1-1/2"
1-1/4", 1-1/2" 1-1/4", 1-1/2" 1-1/4", 1-1/2"
#60/62/65 Plug
#70 External Coupling
#106E Double Side Outlet Cross
1-1/4", 1-1/2" 1-1/4", 1-1/2" 3/4", 1-1/4", 1-1/2"
www.rgpgrates.com
57Slip-On Handrail Fittings
1-1/4" & 1-1/2" Schedule 40 Galvanized Malleable Iron Fittings by Kee Klamp
877-638-6365
58 Handrail Fittings
Ornamental Balls and Hemispheres
These hollow metal balls and hemispheres have a wide range of applications for the designer and fabricator. The holes in the ends are for manufacturing and may be plugged.
Steel balls are 11-gauge
Aluminum, Stainless, and brass walls are 1/8" thick
Mill finish with weld seam standard. Specific finishes available upon request
Polishing NOT recommended for aluminum ballsHollow balls contain drilled alignment hole:
1-1/2" to 6" dia. have 13/64" hole
8" to 12" dia. have 5/16" holeHemisphere holes:
1-1/2" to 6" dia have no hole
8" to 12" dia. have 5/16" hole
•
•
•
•
•
•
•
•
www.rgpgrates.com
59Safety Tread Nosings
Safety Stair Nosings – Cast Nosings
Abrasive Cast Metal
Advanced manufacturing equipment and special mold-ing process assure the lowest cost per unit.
Longest wearing
Impact resistant
Barrier-free
Anti-slip surface
Economical
•
•
•
•
•
Choice of metals:
Alumacast– Corrosion resistant, maintenance-free alu-minum alloy all-purpose usage.
Feracast– Cast iron all-purpose usage. Will withstand heavy industrial punishment. Ships with one coat of shop-applied black paint.
Bronzacast– Rich bronze finish makes this an ideal choice for an upscale, classic effect.
Nickelcast– Combination of nickel and bronze blends with stainless steel architecture.
•
•
•
•
877-638-6365
62 Safety Stair Nosings
“Sure Step” Barrier Free Stair Nosings– Extruded Base Designs
Extruded, abrasive filler
Advanced manufacturing equipment and special mold-ing process assure the lowest cost per unit.
Impact resistant
Barrier-free
Anti-slip surface
Choice of color
Economical
•
•
•
•
•
Choice of color:
Choice of color enhances the appeal of these hand-some "sure step" safety stair nosings. Designed for heavy-duty use indoors and outdoors, these safety nosings meet and exceed all OSHA and barrier-free requirements.
Colors are locked into the epoxy abrasive mixture and will not fade or wear off, maintaining a rich color to blend with any decor.
Available colors: Black (standard), Safety Yellow, Gray, Red, Blue, Safety Orange, Green, Burgandy, Buff, Brown.
877-638-6365
64 Safety Stair Nosings
Safety Strip for Visually Impaired
Renovation Treads– Easy Install
Renew safety on worn and slippery stairs
Renovate and update any stairway without the costly labor of removing and rebuilding the old stair. Robertson Grating Products offers a variety of impact resistant reno-vation treads for every condition.
For any location
renovation treads install easily over worn stairways of every type including concrete, wood, steel, marble, and terrazzo. They can be used inside and out and are ideal for heavy traffic stairways.
Fast, easy installation
renovation treads are delivered drilled and counter-sunk, ready for immediate installation by anyone who can handle a screwdriver. This installation-ready feature eliminates the greatest expense for stair repair– the need for professional labor.
Lasting beauty and protection
The attractive colors of our renovation treads renew old, worn stairways. Drab and unsafe stairs become bright and contemporary with anti-slip protection at every step.
New Vision-Line
Robertson grating Products Vision-Line highlights the leading edge of each tread, providing visibility going down steps even in dimly lit places. The Vision-Line is especially helpful to the vision impaired.
Free Estimates • Complete Fabrication • CAD Drawings
877-638-6365 toll-free • 877-794-5629 fax • Sales e-mail: [email protected]. Box 2889 • Clackamas, OR 97015
Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . .1Steel Bar Grating . . . . . . . . . . . . . . . .2Heavy-Duty Steel Bar Grating . . . . . .3Wheels n’ Heels® Grating . . . . . . . . .4Aluminum Bar Grating . . . . . . . . . . . .5Grating Stair Treads . . . . . . . . . . . . . .6Safety Grating . . . . . . . . . . . . . . . . . .7Slip-Not® Components . . . . . . . . . . . .8Glossary of Terms . . . . . . . . . . . . . . .9Bar Grating Standards . . . . . . . . . . . .10Aluminum Plank . . . . . . . . . . . . . . . . .13RGP Molded Fiberglass Grating . . . .15Pultruded Fiberglass Grating . . . . . . .16RGP Plate & RGP Covered Grating . .18RGP Structural Fiberglass & Hardware .19GRIP-STRUT® Safety Grating . . . . . .20PERF-O GRIP® Grating . . . . . . . . . . .31TRACTION TREAD Flooring . . . . . . .37GRATE LOCK Grating . . . . . . . . . . . .38Pre-Shaped Trench Drain . . . . . . . . .41Drainage Trench Solutions . . . . . . . . .42Foundry Castings . . . . . . . . . . . . . . .43Perforated Metal . . . . . . . . . . . . . . . .44Woven and Welded Wire . . . . . . . . . .45Expanded Metal . . . . . . . . . . . . . . . . .46Handrail Fittings . . . . . . . . . . . . . . . . .47Post Caps & End Caps . . . . . . . . . . .52Caps & Flanges . . . . . . . . . . . . . . . . .53Slip-On Handrail Fittings . . . . . . . . . .54Handrail Fittings . . . . . . . . . . . . . . . . .58Safety Stair Nosings . . . . . . . . . . . . .59
877-638-6365 toll-free • 877-794-5629 fax
Sales e-mail: [email protected]
P.O. Box 2889, Clackamas, OR 97015
TOLL FREE 1-877-638-6365 TOLL FREE 1-877-638-6365
www.rgpgrates.com www.rgpgrates.com
PRESORTEDSTANDARD
U.S. POST AGE PAIDPORTLAND, OR
PERMIT NO. 3995
Robertson Grating Products, Inc.P.O. box 2889Clackamas, OR 97015
Robertson Grating Products Inc.
9180 SE Lawnfi eld Road PO Box 2889
Clackamas, OR 97015
Toll Free: 877-638-6365
Fax: 877-794-5629 Local: 503-794-5629
Local Fax: 503-794-5632e-mail: [email protected] BAR GRATING
PLANK GRATING
FIBERGLASS GRATING
HANDRAIL FITTINGS
SAFETY NOSINGS
POLYDRAIN
PERFORATED METALS
WOVEN WIRE
PRODUCTS AND SERVICE GUIDE
“The Grate Company”