®

Copyright © 2016 The Crosby Group LLC All Rights Reserved

RIG

GIN

G A

CC

ES

SO

RIE

S

187

Lifting Points

S-265 Weld-On Pivot LinkWorking Load Limit (t)

S-265Stock No

Weight Each(kg)

Dimensions(mm) Minimum Fillet

Weld Size(mm)

Design Factor5:1

Design Factor4:1 A B C D F G H

1 1.2 1290740 .40 40 36 83 35 13 66 42 32.5 3.2 1290768 .60 45 44 99 42 18 81 48 34.2 5.3 1290786 1.20 55 50 123 49 22 99 57 66.4 8 1290802 2.40 70 64 144 64 26 122 67 612 15 1290820 5.90 97 90 193 86 34 165 94 8

On Pages 208 -209

SEE APPLICATION AND WARNING INFORMATION

Para Español: www.thecrosbygroup.com

On Page 215 -216

SEE APPLICATION AND WARNING INFORMATION

Para Español: www.thecrosbygroup.com

• or e teel en he an e ere • ellent el in alities • i el se on ar a hiner tr s steel h lle arine vessels

an aterial han lin e i ent• e eren e eri an el in o iet s e ifi ations or proper

el in ro e res

SL-150 UNC SLIDE-LOC™ LIFT POINT

SL-150 METRIC SLIDE-LOC™ LIFT POINT

Weight Each(kg)

SL-150MStock No.

Working Load Limit (t)*

Dimensions(mm) Effective Thread

Projection LengthT

Bolt SizeA B C F E H

.14 1068515 .5 M10X1.5 X 25 35,5 53,1 8,5 28,0 28,0 14,7.23 1068524 .75 M12x1.75x30 42,5 62.9 10,5 33,0 33,0 18,1.50 1068533 1.5 M16x2x40 55,0 75,7 13,2 37.0 37.0 24,5.94 1068542 2.3 M20x2.5x50 68,8 91,1 16,0 43,6 43,6 31,01.60 1068551 3.2 M24x3x60 82,5 110,0 18,2 52,8 52,8 37,0

S - 265el n Pi ot in

SL- 150li e o

i tin Point

• aila le in a a ities ro to etri tons• ail is or e llo teel en he an e ere• ail s i els e ree• ate at or e ree an le• ati e rate to les at ti es the or in oa i it• eets the a hiner Dire ti e C i elines an is ar e ith C

a or in l• eets or e ee s all re ire ents o in l in i entifi ation

tilit esi n a tor roo loa an te erat re re ire ents ortantl these olts eet other riti al er or an e re ire ents in l in ati e li e i a t ro erties an aterial tra ea ilit not a resse

• e la ea le olts a aila le in l in lon er olts• olt s e ifi ation or etri olt is ra e allo a s re to • ni e lo in e hanis a es the li tin oint ell s ite or i

atta h ent to loa s r a e o nee or tools• eat res QUIC-CHECK® ar in s on ail to assist in no in hen e i e

is rea or li tin

* lti ate loa is ti es the or in oa i it

* lti ate loa is ti es the or in oa i it

Weight Each(lbs.)

SL-150MStock No.

Working Load Limit (t)*

Dimensions(in.) Effective Thread

Projection LengthT

Bolt SizeA B C F E H

0.30 1068507 .5 3/8 - 16 x 1 1.40 2.09 0.33 1.10 1.10 .590.53 1068516 .75 1/2 - 13 x 1 - 1/4 1.67 2.48 0.41 1.30 1.30 .781.10 1068525 1.5 5/8 - 11 x 1 - 5/8 2.17 2.98 0.52 1.46 1.46 1.022.05 1068534 2.3 3/4 - 10 x 2 2.71 3.59 0.63 1.72 1.72 1.252.16 1068543 2.3 7/8 - 9 x 2 - 1/1 2.71 3.56 0.63 1.72 1.62 1.283.73 1068552 3.2 1 - 8 x 3 3.25 4.33 0.72 2.08 1.93 1.59

Copyright © 2016 The Crosby Group LLC All Rights Reserved208

WARNING• Loads may disengage from link if proper welding,

assembly, and lifting procedures are not used.

• A falling load may cause serious injury or death.

• Do not use with damaged slings or chain. For sling inspection criteria see ASME B30.9.

• Read and understand these instructions before welding on, or using the pivoting link.

Important Safety Information - Read and Follow

• Use weld-on pivoting link only with ferrous metal (steel) workpiece.

• After determining the loads on each weld-on pivoting link, select the proper size using the Working Load Limit (WLL) ratings in Table 1 on next page.

• Always make sure the weld-on pivoting link and mounting surface is free of dirt or contaminants before installation.

• Never use spacers between the weld-on pivot link and mounting surface.

• Always select proper load rated lifting device for use with weld-on pivoting link.

• Attach lifting device ensuring free movement of weld-on pivoting link bail (Figure 1).

• Apply partial load and check proper alignment. There should be no interference between load (workpiece) and weld-on pivoting link (Figure 2).

• Always ensure free movement of bail. The bail should pivot 180 degrees (Figure 4).

• The support structure that the pivot link is attached to must be of suitable size, composition and quality to support the anticipated loads of all operating positions. The required support structure thickness for a given application is dependent on variables such as unsupported length and material strength, and should be determined by a qualified individual.

• Never repair, alter, rework or reshape the pivoting link bail by welding, heating, burning or bending.

Do not reeve slings from one bail to another. This will alter the load and angle of loading on the pivoting link.

After slings have been properly attached to the pivoting link, apply force slowly. Watch the load and be prepared to stop applying force if the load starts buckling.

Buckling may occur if the load is not stiff enough to resist the compressive force which results from the angular loading.

CROSBY® WELD-ON PIVOTING LINK WARNING & APPLICATION INSTRUCTIONS

WRONG WRONG

Weld-on Pivoting Link Inspection / Maintenance

• Always inspect weld-on pivoting link before use.• Regularly inspect weld-on pivoting link

parts (Figure 3).• Never use weld-on pivoting link that shows signs of

corrosion, wear or damage.• Never use weld-on pivoting link if bail is bent or elongated.• Do not use part showing cracks, nicks or gouges.• Always make sure there are no spacers used between

weld-on pivoting link and the mounting surface.• Always be sure workpiece surface is in total contact with the

weld-on pivoting link base mating surface.• Always inspect the weld-on pivoting link bail and base for

wear.• A visual periodic inspection of the weld should be

performed. Check the weld visually, or use a suitable NDE method if required.

Figure 1 Figure 2 Figure 3 Figure 4

RIGHTExternal Inspection Points

180˚ PIVOT

Operating Safety• Never exceed the capacity (WLL) of the weld-on pivoting link (Table 1, next page).

• Never apply load except in line with the pivot direction (Figure 4).

• When using lifting slings of two or more legs, make sure the forces in the legs are calculated using the angle from the horizontal sling angle to the leg and select the proper size link.

Possible Wear

WeldFree

Movement

WRONG

rev 2

S-265