Rhinestone guide Pro-Finalep.yimg.com/ty/cdn/yhst-83279695798634/rsg-pro.pdf · 1 ©2010 Graphtec...
1
1 ©2010 Graphtec America, Inc. All rights reserved. Graphtec Rhinestone Stencil material Roll of 15 in. x 10 yds. Part #GRS1510-M www.graphtecamerica.com Rhinestone Decorating made simple with the CE5000 & FC8000 The new rhinestone design is now ready for sale! Lift the rhinestones (now attached to transfer tape) from the template and position the design on desired surface. 6 7 Set the heat press to 350 degrees F, for 10 seconds, press on medium. 8 Let the rhinestones cool, then peel the transfer tape. 2 Once all of the rhinestones are positioned face-up in the template, cover the design with a piece of transfer tape. 3 Affix the template material to a rhinestone backing board. 9 Choose a pre-made rhinestone design — or create your own with i-DesignR™ CE or PRO Software. Do NOT resize it. Feed the blue Graphtec Rhinestone Stencil material into the CraftROBO Pro. The standard blue-tipped blade holder and CB09U blade can be used. For 10SS (3mm) and smaller rhinestones, the optional red-tipped blade holder and CB15U-K30 blade gives optimum results. Set blade depth Set the force to 24 Set speed to 30 Set quality to 1 Set Tangential Emulation to 1 Set the Start and End points to 0.028" Gently brush rhinestones into template holes using a brush (one is provided in the optional Starter Kit). Peel the backing from the template material leaving the circle cutouts behind. It works best to peel the material off in one quick motion. Wash and dry clothes inside out. Use caution when operating a heat press. 4 5
Transcript of Rhinestone guide Pro-Finalep.yimg.com/ty/cdn/yhst-83279695798634/rsg-pro.pdf · 1 ©2010 Graphtec...
1
©2010 Graphtec America, Inc. All rights reserved.
Graphtec Rhinestone Stencil materialRoll of 15 in. x 10 yds.Part #GRS1510-M www.graphtecamerica.com
Rhinestone Decorating made simple with the CE5000 & FC8000
The new rhinestone design isnow ready for sale!
Lift the rhinestones (now attached totransfer tape) from the template andposition the design on desired surface.
6 7Set the heat press to 350 degrees F,for 10 seconds, press on medium.
©2010 Graphtec America, Inc. All rights reserved.
8Let the rhinestones cool, then peelthe transfer tape.
2
Once all of the rhinestones are positioned face-up in the template, cover the design with a piece of transfer tape.
3Affix the template material to arhinestone backing board.
9
Choose a pre-made rhinestonedesign — or create your own withi-DesignR™ CE or PRO Software.Do NOT resize it.
Feed the blue Graphtec RhinestoneStencil material into the CraftROBO Pro.The standard blue-tipped blade holderand CB09U blade can be used.
For 10SS (3mm) and smaller rhinestones, the optional red-tipped blade holder and CB15U-K30 blade gives optimum results.
Set blade depthSet the force to 24Set speed to 30Set quality to 1Set Tangential Emulation to 1Set the Start and End points to 0.028"
Gently brush rhinestones intotemplate holes using a brush (one isprovided in the optional Starter Kit).
Peel the backing from the templatematerial leaving the circle cutoutsbehind. It works best to peel thematerial off in one quick motion.
Wash and dry clothes inside out. Use caution when operating a heat press.
4 5
