RFP Issuance Date: Clarification/Question Due: Closing ... · small business hubzone small business...
77
Transcript of RFP Issuance Date: Clarification/Question Due: Closing ... · small business hubzone small business...
Physical Address:U.S. Agency for International Development Mobil Building N° 198 Avenue IsiroGare Centrale / Gombe / KinshasaDemocratic Republic of Congo
U.S. Postal Address:USAID/DRCUnit 31550APO AE 09828-1550
Tel: (+243) 81 555 4430Fax (+243) 81 555 3528http://www.usaid.gov/cg
RFP Issuance Date: June 10, 2019Clarification/Question Due: COB Local Time, June 20, 2019Site Visit June 17-18, 2019Closing Date and Time: COB Local Time, July 5, 2019
SUBJECT: Solicitation № 72066019Q00003Solicitation Title: HVAC Upgrade at USAID Kinshasa Office
ATTENTION PROSPECTIVE OFFERORS:
The United States Agency for International Development in the Democratic Republic of Congo (USAID/DRC) is seeking proposals from qualified Entities for the upgrade of the HVAC system at its main office compound per attached Statement of Work contained in Section C. A fixed price contract is contemplated for the services to be provided under this contract.
USAID will conduct this procurement through full and open competition.
Applicants are reminded that US Executive Orders and US law prohibits transactions with, and the provision of resources and support to, individuals and organizations associated with terrorism. It is the legal responsibility of the recipient to ensure compliance with these Executive Orders and laws. This provision must be included in all subcontract-awards issued under this Contract if any.
Offerors must demonstrate that they believe the costs proposed are realistic and reasonable to provide the intended service as described in Section C. The offerors are expected to provide their best reasonable and competitive price to undertake the statement of work.
The RFP addresses all of the specifics associated with this requirement. Offerors are encouraged to read the entire solicitation. Special attention should be paid to the Instructions to Offerors in Section L, and the Evaluation Factors in Section M.
Additionally, USAID/DRC requires that the proposals must be submitted only electronically (e-mailed)
All U.S. Government contractors are required to secure a Data Universal Numbering System (DUNS) Number and be registered in the System for Award Management (SAM) before award can be made to them. Obtaining DUNS and registration in SAM takes some time. It is therefore advised that interested offerors start obtaining DUNS and SAM immediately. Please refer to section L2 and L.3 for more information on DUNS number and SAM registration.
The primary point of contract for this RFP is the Procurement Agent, Boris Kabeya. Any questions related to this RFP must be submitted by email to [email protected] by no later than the time and date specified above. Responding to questions thereafter is at the Contracting Officer's discretion. Any information given to a prospective offeror concerning this RFP will be furnished to all offerors as an amendment to the solicitation. Proposals should be submitted to Boris Kabeya at [email protected] and to Priscilla Sampil at [email protected] no later than the date and time specified above.
Physical Address:U.S. Agency for International Development Mobil Building N° 198 Avenue IsiroGare Centrale / Gombe / KinshasaDemocratic Republic of Congo
U.S. Postal Address:USAID/DRCUnit 31550APO AE 09828-1550
Tel: (+243) 81 555 4430Fax (+243) 81 555 3528http://www.usaid.gov/cg
This letter does not obligate USAID/DRC to award a contract, nor does it commit USAID to pay for any costs incurred in the preparation and submission of a proposal in response hereto.
Thank you for your interest.
Sincerely,
Ifeoma EzehContracting Officer
SEE ADDENDUMIS CHECKED
CODE 18a. PAYMENT WILL BE MADE BY
CODE
FACILITYCODE
17b. CHECK IF REMITTANCE IS DIFFERENT AND PUT SUCH ADDRESS IN OFFER
OFFEROR
USAID/DROC CODE 16. ADMINISTERED BYCODE
X
X
SIZE STANDARD:
% FOR:SET ASIDE:UNRESTRICTED OR720660
RFPIFB
10. THIS ACQUISITION ISCODE
RFQ
14. METHOD OF SOLICITATION
13b. RATING
NAICS:
SMALL BUSINESS
07/05/2019 1700 A
06/10/2019
+243 81 715 1139Boris Kabeya(No collect calls)
INFORMATION CALL:
FOR SOLICITATION 8. OFFER DUE DATE/LOCAL TIMEb. TELEPHONE NUMBER a. NAME
4. ORDER NUMBER3. AWARD/ 6. SOLICITATION
72066019Q000035. SOLICITATION NUMBER
SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS 1. REQUISITION NUMBER PAGE OF
1 67 OFFEROR TO COMPLETE BLOCKS 12, 17, 23, 24, & 30
TELEPHONE NO.
17a. CONTRACTOR/
Kinshasa/Gombe, DROC1980 Isiro AvenueUSAID/DROCExecutive OfficeUSAID/DROC
15. DELIVER TO
00000
9. ISSUED BY
7.
2. CONTRACT NO.
EFFECTIVE DATE
18b. SUBMIT INVOICES TO ADDRESS SHOWN IN BLOCK 18a UNLESS BLOCK BELOW
ISSUE DATE
DELIVERY FOR FOB DESTINA-
TION UNLESS BLOCK IS
MARKED
11.
SEE SCHEDULE
12. DISCOUNT TERMS
THIS CONTRACT IS A
RATED ORDER UNDER
DPAS (15 CFR 700)
13a.
SERVICE-DISABLED
VETERAN-OWNED
SMALL BUSINESS
HUBZONE SMALL
BUSINESS
8(A)
USAID/DROC (Congo)WOMEN-OWNED SMALL BUSINESS
(WOSB) ELIGIBLE UNDER THE WOMEN-OWNED
SMALL BUSINESS PROGRAM
EDWOSB
24.
AMOUNT
23.
UNIT PRICE
22.
UNIT
21.
QUANTITY
20.
SCHEDULE OF SUPPLIES/SERVICES
19.
ITEM NO.
0001 See Section C.
(Use Reverse and/or Attach Additional Sheets as Necessary)
HEREIN, IS ACCEPTED AS TO ITEMS:
DATED
Ifeoma Ezeh
. YOUR OFFER ON SOLICITATION (BLOCK 5),
INCLUDING ANY ADDITIONS OR CHANGES WHICH ARE SET FORTH
COPIES TO ISSUING OFFICE. CONTRACTOR AGREES TO FURNISH AND DELIVER
ARE
ARE
31c. DATE SIGNED
27b. CONTRACT/PURCHASE ORDER INCORPORATES BY REFERENCE FAR 52.212-4. FAR 52.212-5 IS ATTACHED. ADDENDA
31a. UNITED STATES OF AMERICA (SIGNATURE OF CONTRACTING OFFICER)
30c. DATE SIGNED 31b. NAME OF CONTRACTING OFFICER (Type or print)
ALL ITEMS SET FORTH OR OTHERWISE IDENTIFIED ABOVE AND ON ANY ADDITIONAL
SHEETS SUBJECT TO THE TERMS AND CONDITIONS SPECIFIED.
27a. SOLICITATION INCORPORATES BY REFERENCE FAR 52.212-1, 52.212-4. FAR 52.212-3 AND 52.212-5 ARE ATTACHED. ADDENDA
26. TOTAL AWARD AMOUNT (For Govt. Use Only)
OFFER
STANDARD FORM 1449 (REV. 2/2012)
Prescribed by GSA - FAR (48 CFR) 53.212
ARE NOT ATTACHED.
ARE NOT ATTACHED.
AUTHORIZED FOR LOCAL REPRODUCTION
PREVIOUS EDITION IS NOT USABLE
30b. NAME AND TITLE OF SIGNER (Type or print)
30a. SIGNATURE OF OFFEROR/CONTRACTOR
28. CONTRACTOR IS REQUIRED TO SIGN THIS DOCUMENT AND RETURN
25. ACCOUNTING AND APPROPRIATION DATA
29. AWARD OF CONTRACT:
REF.
32e. MAILING ADDRESS OF AUTHORIZED GOVERNMENT REPRESENTATIVE
32c. DATE 32b. SIGNATURE OF AUTHORIZED GOVERNMENT REPRESENTATIVE
ACCEPTED, AND CONFORMS TO THE CONTRACT, EXCEPT AS NOTED:
32a. QUANTITY IN COLUMN 21 HAS BEEN
RECEIVED INSPECTED
40. PAID BY39. S/R VOUCHER NUMBER38. S/R ACCOUNT NUMBER
37. CHECK NUMBER
FINALPARTIAL
36. PAYMENT
FINALPARTIAL
35. AMOUNT VERIFIED
CORRECT FOR
34. VOUCHER NUMBER33. SHIP NUMBER
COMPLETE
32g. E-MAIL OF AUTHORIZED GOVERNMENT REPRESENTATIVE
42d. TOTAL CONTAINERS42c. DATE REC'D (YY/MM/DD)
42b. RECEIVED AT (Location)
42a. RECEIVED BY (Print)
41c. DATE41b. SIGNATURE AND TITLE OF CERTIFYING OFFICER
41a. I CERTIFY THIS ACCOUNT IS CORRECT AND PROPER FOR PAYMENT
STANDARD FORM 1449 (REV. 2/2012) BACK
24.
AMOUNT
23.
UNIT PRICE
22.
UNIT
21.
QUANTITY
20.
SCHEDULE OF SUPPLIES/SERVICES
19.
ITEM NO.
32f. TELEPHONE NUMBER OF AUTHORIZED GOVERNMENT REPRESENTATIVE
32d. PRINTED NAME AND TITLE OF AUTHORIZED GOVERNMENT REPRESENTATIVE
67 2 of
1
SECTION 1: SUPPLIES OR SERVICES AND PRICE/COSTS 1.1. OBJECTIVE The U.S Agency for International Development (USAID) requires design build services to replace and/or upgrade the aging HVAC systems at the USAID Office building in Kinshasa. This work will include the removal of the existing HVAC and the installation of new systems as shown in EXHIBIT A - (VRV/VRF System) scope of work (SOW) as included as part of this package. This statement of work (SOW) defines the services to be performed by the Mechanical Contractor, hereafter referred to as the Contractor. A pre-bid walk-thru will be coordinated with bidders by the Contracting Officer (CO). 1.2 CONTRACT TYPE The U.S. Government contemplates award of a Firm-Fixed-Price (FFP) contract resulting from this solicitation. For the consideration set forth below, the Contractor shall provide the deliverables or outputs described in Section F based on the Statement of Work (SOW) found in Section C of this solicitation. 1.3 ESTIMATED COST, AND OBLIGATED AMOUNT Subject to the availability of funds, USAID intends to provide and amount TBD for the removal of the existing HVAC and the installation of new systems. 1.4 PRICE/COST SCHEDULE The following is the Budget Schedule: TBD
LINE ITEM COST Removal of the existing HVAC TBD Equipment TBD Installation of a new system TBD Others TBD TOTAL TBD
Note: 1. TBD amount will be completed upon negotiation of final cost agreed between the Contractor and USAID.
[END OF SECTION B] SECTION 2: DESCRIPTION/SPECIFICATIONS/STATEMENT OF WORK (SOW) Under the direction of the Contracting Officer Representative (COR) for this activity, the contractor shall undertake all tasks as spelt out in this statement of work.
72066019Q00003 HVAC UPGRADE
2
2.0 General Timeline and Expectations. The new equipment shall be procured only after receiving approval on submittals by the COR. The Contractor shall provide a schedule to the project COR for review and approval. The contractor shall provide equipment start-up / commissioning by a factory certified technician and the contractor shall provide training to the local staff.
2.1 Basic Work Summary. The Contractor shall provide qualified workers, equipment and materials
necessary to:
1. Demolition - Remove the existing split AC unit, existing air-handling units pump sets, expansion tanks, dehumidification equipment / controls, connected piping, connected ductwork, controls, electrical conduit/wiring, and other associated components that will not be reused for the new work requirements.
2. Crane Access / Rigging - The contractor shall pay close attention to the limited site
access and potential complications with rigging and crane access. The contractor will be required to provide crane and rigging plans for each SOW option.
3. New Equipment – For new work/equipment requirements, see the included
HVAC (VRV System) SOW.
4. Trades required to complete the required work shall include, but may not be limited to mechanical, electrical, concrete, plumbing, and carpentry. In addition to the new equipment, rigging, piping, piping accessories, disconnect switches, electrical connections, vibration isolation, insulation, controllers, controls wiring and personnel training are included in the work for this project. Mechanical, Electrical, Light Carpentry, Concrete, and Painting trade work may be involved. Testing, Adjusting, and Balancing (TAB), system start-up, system flushing and basic adjustments of the new equipment are also part of the work.
2.2 Building Codes. Work under this project is governed local codes and by the latest adopted
version of the International Building Code (IBC), which includes the International Mechanical Code, International Plumbing Code, and National Electric Code (NEC). If there is conflict between local and or International codes, the more stringent requirement shall be followed. New work being provided shall, at a minimum, be equal to or improve upon the current installation. The Contractor shall perform all work in a workmanlike manner to provide a first- class, fully complete, and functional installation. The quality of the new work provided shall be approved by the Government’s COR. The Contractor shall remove, correct, and replace any work deemed unacceptable at the discretion of the COR.
2.3 Additional Included Information. Included with this Statement of Work narrative are attached
exhibits including (Exhibit A) SOW, (Exhibit B) Project Orientation existing conditions& Photos, (Exhibit C) proposed work BOQ, (Exhibit D) Basis of Design Equipment (BOD) Selections.
1. SOW – See Exhibit A for sections 3 and 4 of the SOW, which includes the requirements for installing a variable refrigerant volume (VRV) system in place of the existing HVAC system.
2. Project Orientation Photos. See Exhibit B for orientation photos of
existing equipment/systems.
3. Proposed Work BOQ. Included in attached Exhibit C. Equipment and work items listed are not used as final design BOQ.
4. Basis of Design Equipment (BOD) Selections. Equipment selection based on
72066019Q00003 HVAC UPGRADE
3
the sales and service of the equipment can be procured locally or easily available regionally with minimum lead time.
2.4 Safety and Security Requirements. The Contractor is responsible for the safety of his/her
employees, and for conduct of the work in a manner that prioritizes the safety of Post residents, employees, and visitors.
1. Additional Safety Guidelines. Work must be conducted in the safest possible
manner, in compliance with local labor standards and with health, safety, sanitation, and injury prevention as the highest priorities. The Contractor shall comply with the following safety guidelines and all additional guidelines defined by the project specifications:
1. The Contractor shall prepare a Safety & Health Protocol and shall designate a Safety Representative, who will be on site through the duration of the work, to be responsible for implementation of proper health, safety, sanitation and accident prevention procedures throughout the contract period. Safety & Health Protocol document shall be reviewed by and Safety Representative shall be introduced to the COR for approval.
2. The Safety & Health Protocol shall establish and document procedures
and requirements regarding the following items: □ Sanitation, Safety and Health Training □ Accident Prevention, Reporting and Investigation □ Hazardous Work and Hazardous Material Handling □ Protective Clothing and Safety Equipment □ Welding Safety (where applicable)
□Ladder and Scaffolding Safety □Safety Signage
□ Emergency Evacuation and Emergency Contacts
3. All guidelines of the Safety & Health Protocol shall be enforced by the Safety Representative on site. Any deviation from the defined safety protocol shall immediately be corrected by the Contractor and reported to the Project Superintendent/COR. The Project Superintendent may require remediation of any conditions deemed unsafe or, unhealthy, and may stop work if conditions are not immediately corrected. The Superintendent may likewise stop work and/or remove the contractor from the site if an accident is not immediately reported for investigation.
1. Refrigerant Handling. The Contractor shall provide all new, non-ozone
depleting refrigerant for new equipment. Handling / charging of refrigerants for use in air conditioning systems shall comply with all U.S., local laws and regulations. For the systems being replaced as a part of the SOW, all ozone depleting refrigerants R-22, shall be reclaimed and removed from the post by the contractor, and disposed of properly per ASHRAE 147.
2. Propylene and Ethylene Glycol / Chemical Handling. The Contractor shall
remove the existing chilled water fluid and piping system, which shall include ethylene or propylene glycol solution and treatment chemicals. Handling / disposal of ethylene or propylene glycol and treatment chemicals shall comply with all U.S. and local laws and regulations.
72066019Q00003 HVAC UPGRADE
4
3. Site Specific Security Requirements. This project is unclassified; however, the contractor must comply with any site specific security requirements, if implemented by the Post.
2.6 Coordination with Post. The items below shall be coordinated with post per the instructions
listed:
2.6.1 As-Built Reference Drawings. Existing design/construction documentation, including AutoCAD files, if available, for the affected area(s) / building(s) shall be provided to the Contractor when requested, by the COR and FM. Availability and accuracy of existing files cannot be guaranteed.
2.6.2 Permitting. Contractor shall coordinate with FM and other Post personnel to
facilitate procuring all required local permits prior to commencing installation. This includes but is not limited to: drawing/sketch production, documentation submission/coordination with the local jurisdiction, and payment for review by the jurisdiction.
2.6.3 Interruptions of Service. The Contractor shall maintain existing systems in
service to the maximum extent possible and coordinate interruptions of any utility services in writing not less than seven (7) days in advance with the Facility Manager. See sections 3 and 4 of this SOW for additional details regarding service interruptions and occupancy requirements.
2.6.4 Storage, Laydown and Staging. Designated areas will be provided by post for
temporary use by the Contractor for storage, laydown and staging. These areas will be established during the pre-bid walk-thru. Any concerns about the size and/or location of these areas should be raised with the FM at that time for resolution.
2.6.5 Debris and Trash Disposal. The Contractor shall be fully responsible for and
shall dispose of all project debris and trash in accordance with local codes and regulations, and in accordance with written instructions from the FM. Demolished equipment, debris, trash, and hazardous materials shall be removed from the property and disposed of at a minimum weekly schedule. FM will provide Contractor with the location(s) for dumpster(s) and container(s). Access for trucks/dumpsters shall be coordinated with the FM.
2.6.6 Protections and Damage. The Contractor shall be responsible to protect all U.S.
Government property to include: all furniture, furnishings, carpets, and interior and exterior architectural finishes from damage. Damage caused by the Contractor to architectural interior and exterior finishes will be returned to original condition by the Contractor. In addition to the architectural finishes, the Contractor shall protect all non-included mechanical and electrical equipment and controls from damage throughout the duration of work. Prior to commencing the work, the contractor along with post representatives shall walk the site that will be impacted by the SOW and document existing conditions. It shall be the Contractor’s responsibility to document in writing any and all pre-existing damaged surfaces prior to the start of the project work and to provide a copy of the documentation to the COR prior to the start of work at the jobsite.
2.6.7 Access to Site – Hours of Operation. Normal hours of operation at the Post are
subject to staff schedules and will be confirmed during the site walk- thru; however, the following are the general project expectations:
2.6.7.1 Typical Hours of Operation: 8 A.M. – 4 P.M.
72066019Q00003 HVAC UPGRADE
5
2.6.7.2 The contractor shall recognize that this SOW takes place at a
office/residential property. The contractor is expected to provide project schedules for the SOW efforts as part of the proposal delivery. The Contractor shall perform work during normal working hours to the maximum extent possible and coordinate any unplanned after-hours work in writing not less than (7) days in advance with the FM. Identify any site specific limitations or restrictions on working hours (e.g., work that generates excessive dust in occupied areas or work involving high levels of noise (e.g., core drilling) shall be performed outside the normal hours of operation.
2.6.8 Contractor Personnel Information. Thirty (30) days prior to the start of work, the
Contractor shall submit requested information for all employees that will be on site to the FM for background checks. Coordinate with Post to determine required information to be submitted and provide at pre-bid walk-thru. Where applicable. The Contractor shall additionally submit all documentation required by local labor regulations.
2.7 Visas, Travel, Per Diem, and Insurance. The Contractor shall include all costs associated with
employees’ visa procurement, travel, per diem, and required Defense Base Act (DBA) insurance in the project bid.. Information regarding DBA insurance requirements and waivers may be found at the U.S. Department of Labor website.
2.8 Shipping and Customs. The Contractor is responsible for shipping, clearing customs, delivery,
and storage of all tools, materials, and equipment to the worksite. At the Contractor’s request, Post is able to provide limited shipping/logistics and customs support. Contractor shall contact the FM to be directed to the proper Post personnel for assistance.
2.9 Submittals. The Contractor shall provide the following submittals for review by the COR and
FM prior to commencement of work. Refer to Section 4 Schedule of Deliverables for all required submittals:
2.9.1 New Equipment. For all new equipment, materials, and chemicals the
Contractor shall provide selection information for review by the COR and FM prior to installation. Provide full documentation for all major equipment and system components.
2.9.2 Meetings. The Contractor shall document and submit, in writing, a record of all conferences and meetings that relate to this task order. This shall include telephone conversations involving decisions affecting this task order. Electronic copies of meeting minutes shall be submitted electronically to the COR and FM.
2.9.3 Crane Study. The Contractor shall submit the proposed crane entry path and
staging location in a graphical (site plan) format for review by the COR and FM.
2.9.4 Safety & Health Protocol. The Contractor shall submit a Safety & Health Protocol document for review by the COR and FM.
2.9.5 Quality Control Plan. The Contractor shall submit a project specific Quality
Control Plan (QCP) for review by the COR and FM. The Contractor shall be responsible to meet the guidelines of the QCP throughout the duration of work and shall be subject to the oversight of the Project Superintendent on all issues relating to project quality.
72066019Q00003 HVAC UPGRADE
6
2.10 Quality of Work. Materials, components, fittings and workmanship shall be in accordance with the project specifications and of equal or better quality than the assemblies being replaced. Quality of all work shall be approved by the COR. The COR shall have the authority to require removal and replacement of any installation that is deemed and justified to be of inferior quality or workmanship to the existing installation at the discretion of the COR prior to final acceptance of the project work.
2.11 Warranty. The Contractor shall provide fully documented warranties on all
equipment, materials, and workmanship. See included specifications for warranty requirements and additional information.
[END OF SECTION C] SECTION D PACKAGING AND MARKING D.1 AIDAR 752.7009 MARKING (JAN 1993) N/A D.2 BRANDING STRATEGY N/A D.3 BRANDING AND MARKING POLICY N/A [END OF SECTION D]
72066019Q00003 HVAC UPGRADE
7
SECTION E INSPECTION AND ACCEPTANCE E.1 NOTICE LISTING CONTRACT CLAUSES INCORPORATED BY REFERENCE The following contract clauses pertinent to this section are hereby incorporated by reference (by Citation Number, Title, and Date) in accordance with the clause at FAR "52.252-2” CLAUSES INCORPORATED BY REFERENCE" in Section I of this contract. See FAR 52.252-2 for an internet address (if specified) for electronic access to the full text of a clause. FEDERAL ACQUISITION REGULATION (48 CFR Chapter 1) NUMBER TITLE DATE 52.246-1 CONTRACTOR INSPECTION REQUIREMENTS APR 1984 52.246-2 INSPECTION OF SUPPLIES-FIXED-PRICE AUG 1996 52.246-4 INSPECTION OF SERVICES-FIXED-PRICE AUG 1996 52.246-15 CERTIFICATE OF CONFORMANCE APR 1984 52.246-16 RESPONSIBILITY FOR SUPPLIES APR 1984 E.2 INSPECTION AND ACCEPTANCE USAID inspection and acceptance of services, reports and other required deliverables or outputs shall take place at the principal place of performance or at any other location where the services are performed and reports and deliverables or outputs are produced or submitted. The Contracting Officer Representative (COR) listed in Section G has been delegated authority to inspect and accept all services, reports and required deliverables or outputs. E.3 MONITORING AND EVALUATION PLAN Monitoring and evaluation programs should be utilized in order to assess the impact of the programs and whether or not objectives are being achieved and if they should be adjusted. The Contractor will input all required information to the USAID/DRC COR on a quarterly basis. [END OF SECTION E]
72066019Q00003 HVAC UPGRADE
8
SECTION F DELIVERIES OR PERFORMANCE F.1 NOTICE LISTING CONTRACT CLAUSES INCORPORATED BY REFERENCE The following contract clauses pertinent to this section are hereby incorporated by reference (by Citation Number, Title, and Date) in accordance with the clause at FAR "52.252-2 CLAUSES INCORPORATED BY REFERENCE" in Section I of this contract. See FAR 52.252-2 for an internet address (if specified) for electronic access to the full text of a clause. FEDERAL ACQUISITION REGULATION (48 CFR Chapter 1) NUMBER TITLE DATE 52.211-8 TIME OF DELIVERY JUN 1997 52.211-9 DESIRED AND REQUIRED TIME OF DELIVERY JUN 1997 52.211-16 VARIATION IN QUANTITY APR 1984 52.242-15 STOP-WORK ORDER AUG 1989 52.242-17 GOVERNMENT DELAY OF WORK APR 1984 52.243-1 CHANGES-FIXED-PRICE AUG 1987 F.2 PERIOD OF PERFORMANCE The exact start date is TBD. F.3 PLACE OF PERFORMANCE Performance of this contract will be principally in Kinshasa, Democratic Republic of Congo. F.4 DELIVERABLES
4.0 Proposal Deliverables (All Bidding Contractors)
CONTRACTORS SHALL PROVIDE SCHEDULES AND EQUIPMENT
PRODUCT LITERATURE FOR.
Number Description Number of Copies
Due Format
A.1 HVAC UPGRADES _VRV/F SYSTEM SCHEDULE: A Detailed Project Design and Construction Schedule
1 Due with
proposal
delivery.
Electronic
A.2 HVAC UPGRADES VRV/F SYSTEM PRODUCT LITERATURE: Example product literature on the equipment the contractor recommends to install as part of the new work. Shall include basic manufacturer and model information; however, detailed equipment selections
1 Due with
proposal
delivery.
Electronic
72066019Q00003 HVAC UPGRADE
9
4.1 Post – Award Deliverables
Number Description Number of Copies
Due Format
1 60% Design Development Documents
- MEP Drawings - Catalog Cuts - Design Calculations
1 NTP + 21
days
Electronic
2 100% Construction Documents Documents - MEP Drawings - Catalog Cuts - Design Calculations
1 NTP + 56
days
Electronic
3 Final Design Issued for Construction (IFC) Drawings / Documents
1 NTP + 70
days
Electronic
4 RFI’s / Proposed Sketches, Modification Requests
1 As Needed Electronic
5 Contractor personnel information to RSO for vetting
1 30 Days Prior
to Site Visits
Electronic
6 Licensed electrical engineer letter validating modifications to electrical service to new equipment
1 Prior to
Project Work
Electronic
7 Seismic Isolators / Seismic calculations by licensed structural engineer
1 Prior to
Project Work
Electronic
8 Equipment submittals 1 Prior to
Project Work
Electronic
9 Quality Control Plan 1 Prior to
Project Work
Electronic
10 Health & Safety Protocol 1 Prior to
Project Work
Electronic
11 Materials/chemicals submittals 1 Prior to
Project Work
Electronic
12 Crane/Rigging Plan/Crane Path 1 Prior to Project Work
Electronic
72066019Q00003 HVAC UPGRADE
10
13 Equipment Warranty Information 1 Prior to
Turnover
Electronic
14 Completed Equipment Commissioning / Startup Checklists and Factory Representative’s Documentation
1 Prior to Turnover Electronic
15 Testing, Adjusting, and Balancing (TAB) Documentation
1 Prior to
Turnover
Electronic
16 Documentation of Post Personnel Training on New Equipment
1 Prior to
Turnover
Electronic
17 Operation & Maintenance Manuals 1 Prior to
Turnover
Electronic
18 Milestone: Communications/Meetings Documentation
1 Meeting + 7
Days
Electronic
19 Spare Equipment Parts All Prior to
Turnover
Physically deliver to
FM Office F.5 PERFORMANCE STANDARDS Evaluation of the Contractor's overall performance in accordance with the performance standards set forth below, will be conducted jointly by the COR and the Contracting Officer, and shall form the basis of the Contractor's permanent performance record with regard to this contract.
a) Quality
• Education, breadth and depth of experience of the Contractor's key personnel. • Quality and effectiveness of materials and equipment provided to USAID. • Extent to which open, transparent relations are established between USAID COR and the Contractor.
b) Cost Control/Effectiveness
• Actual costs incurred against the Contractor's cost proposal.
c) Timeliness of Performance
• Long Term and Short-term technical assistance are identified and fielded in a timely manner. • Ability of the Contractor to take corrective action to compensate for delays which were outside the Contractor's
control. • Timeliness of documents or reports submitted to USAID.
F.6 REPORTS
72066019Q00003 HVAC UPGRADE
11
In addition to the requirements set forth for submission of reports in Sections I and J and in the AIDAR clause 752.242-70, Periodic Progress Reports, the Contractor shall provide the following to the designated COR in Section G: Mobilization Plan: The contractor shall submit a mobilization/timeline plan detailing the timeframe for deploying staff, procuring supplies and/or equipment, and initiating work activities for any installation work related to the services requested in SECTION C above. F.7 KEY PERSONNEL a. The Contractor’s shall provide the following key personnel primary point of contacts (POC) is: Title Name
1. HVAC Engineer TBD
a) Qualification: Key Personnel must have the following qualification and experience:
• Professional expertise in HVAC Engineering services • A minimum of three years’ experience as HVAC Engineering • Ability to read, speak and understand English
b) The personnel specified above is considered to be essential to the work being performed hereunder. Prior to
replacing the specified individual, the Contractor must notify both the Contracting Officer (CO) and the COR at least a month in advance and in writing.
c) The contractor’s primary point of contact is expected to fulfill the following responsibilities and meet the following desired minimum qualifications:
• Ensure proper administration of the contract. • Provide technical guidance and serve as a subject matter expert in technical area. • Provide regular and constructive feedback to USAID COR.
[END OF SECTION F]
72066019Q00003 HVAC UPGRADE
12
SECTION G - CONTRACT ADMINISTRATION DATA G.1 TEXTS OF USAID CONTRACT CLAUSES 752-7003 DOCUMENTATION FOR PAYMENT (NOV 1998) G.2 CONTRACTING OFFICER'S AUTHORITY The Contracting Officer is the only person authorized to make or approve any changes in the requirements of this Contract and notwithstanding any provisions contained elsewhere in this Contract, the said authority remains solely in the Contracting Officer. In the event the Contractor makes any changes at the direction of any person other than the Contracting Officer, the change will be considered to have been made without authority and no adjustment shall be made in the contract terms and conditions, including price. All questions concerning the administration of this award shall be sent to the Contracting Officer. It is the responsibility of the Contractor to inform the Contracting Officer of requests that affect any and all sections of this award. The Contracting Officer is located at: Executive Office (EXO)
USAID/DRC 198 Isiro Avenue Kinshasa/DRC
G.3 ADMINISTRATIVE CONTRACTING OFFICE The Administrative Contracting Office is: Executive Office USAID/DRC 198 Isiro Avenue Kinshasa/DRC G.4 TECHNICAL DIRECTIONS/RELATIONSHIP WITH USAID (a) Technical Directions is defined to include: (1) Written directions to the Contractor which fill in details, suggest possible lines of inquiry, or otherwise facilitate completion of work; (2) Provision of written information to the Contractor which assists in the interpretation of drawings, specifications, or technical portions of the work statement; (3) Review and, where required, provide written approval of technical reports, drawings, specifications, or technical information to be delivered. Technical directions must be in writing, and must be within the scope of the work as detailed in Section C. (b) The COR is authorized by designation to take any or all action with respect to the following which could lawfully be taken by the Contracting Officer, except any action specifically prohibited by the terms of this Contract: (1) Assure that the Contractor performs the technical requirements of the contract in accordance with the contract terms, conditions, and specifications. (2) Perform or cause to be performed, inspections necessary in connection with a) above and require the Contractor to correct all deficiencies; perform acceptance for the Government. (3) Maintain all liaison and direct communications with the Contractor. Written communications with the
72066019Q00003 HVAC UPGRADE
13
Contractor and documents shall be signed as "Cognizant Officer" with a copy furnished to the Contracting Officer. (4) Issue written interpretations of technical requirements of Government drawings, designs, and specifications. (5) Monitor the Contractor's production or performance progress and notify the Contractor in writing of deficiencies observed during surveillance, and direct appropriate action to effect correction. Record and report to the Contracting Officer incidents of faulty or nonconforming work, delays or problems. (6) Obtain necessary security clearance and appropriate identification if access to Government facilities is required. If to be provided, ensure that Government furnished property is available when required. LIMITATIONS: The COR is not empowered to award, agree to, or sign any contract (including delivery or purchase orders) or modifications thereto, or in any way to obligate the payment of money by the Government. The COR may not take any action which may impact on the contract schedule, funds, scope or rate of utilization of LOE. All contractual agreements, commitments, or modifications which involve prices, quantities, quality, and schedules shall be made only by the Contracting Officer. (c) The COR is required to meet quarterly/semi-annually/annually with the Contractor and the Contracting Officer concerning performance of items delivered under this contract and any other administration or technical issues. Telephonic reports may be made if no problems are being experienced. Problem areas should be brought to the immediate attention of the Contracting Officer. (d) In the absence of the designated COR, the COR may designate someone to serve as COR in their place. However, such action to direct an individual to act in the COR's stead shall immediately be communicated to the Contractor and the Contracting Officer. (e) Contractual Problems - Contractual problems, of any nature, that may arise during the life of the contract must be handled in conformance with specific public laws and regulations (i.e. Federal Acquisition Regulation and Agency for International Development Acquisition Regulation). The Contractor and the COR shall bring all contracting problems to the immediate attention of the Contracting Officer. Only the Contracting Officer is authorized to formally resolve such problems. The Contracting Officer will be responsible for resolving legal issues, determining contract scope and interpreting contract terms and conditions. The Contracting Officer is the sole authority authorized to approve changes in any of the requirements under this contract. Notwithstanding any clause contained elsewhere in this contract, the said authority remains solely with the Contracting Officer. These changes include, but will not be limited to the following areas: scope of work, price, quantity, technical specifications, delivery schedules, and contract terms and conditions. In the event the Contractor effects any changes at the direction of any other person other than the Contracting Officer, the change will be considered to have been made without authority. (f) Failure by the Contractor to report to the Administrative Contracting Office, any action by the Government considered to a change, within the specified number of days contained in FAR 52.243-7 (Notification of Changes), waives the Contractor's right to any claims for equitable adjustments. G.5 PAYING OFFICE All vouchers/invoices MUST be sent electronically to: [email protected]. G.6 ACCOUNTING AND APPROPRIATION DATA
Budget Fiscal: Operating Unit: Strategic Objective: Team/Division: Benefiting Geo Area: Object Class:
72066019Q00003 HVAC UPGRADE
14
Amount Obligated: G.8 CONTRACTOR’S PAYMENT ADDRESS ________________TBD___________________________________________ ___________________________________________________________ ___________________________________________________________ ___________________________________________________________ [To be filled in at time of Award] [END OF SECTION G]
72066019Q00003 HVAC UPGRADE
15
SECTION H - SPECIAL CONTRACT REQUIREMENTS H.1 NOTICE LISTING CONTRACT CLAUSES INCORPORATED BY REFERENCE The following contract clauses pertinent to this section are hereby incorporated by reference (by Citation Number, Title, and Date) in accordance with the clause at FAR "52.252-2 CLAUSES INCORPORATED BY REFERENCE" in Section I of this contract. See FAR 52.252-2 for an internet address (if specified) for electronic access to the full text of a clause. NUMBER TITLE DATE
FEDERAL ACQUISITION REGULATION (48 CFR Chapter 1) AIDAR 48 CFR Chapter 7
752.7027 PERSONNEL DEC 1990 H.2 AUTHORIZED GEOGRAPHIC CODE Any commodities that must be purchased by the Contractor in order to fulfill the terms of the Contract may be purchased locally provided that (1) commodities with a value of under US$5,000 may be purchased with an origin and nationality of Code 937 (any country other than the following: Libya, Vietnam, Cuba, Laos, Iran, North Korea, and Syria) and (2) any commodity with a value over US$5,000 must be of U.S. source and origin unless a written waiver is obtained in advance from USAID. Any commodities that must be purchased by the Contractor in order to fulfill the terms of the contract and that are not available locally must be of U.S. source, origin and nationality unless a written waiver is obtained in advance from USAID. H.3 LOGISTIC SUPPORT The Contractor shall be responsible for furnishing all logistic support related to connectivity, procurement and dealing with the Host Government if any. H.4 EXECUTIVE ORDER ON TERRORISM FINANCING The Contractor/Recipient is reminded that U.S. Executive Orders and U.S. law prohibits transactions with, and the provision of resources and support to, individuals and organizations associated with terrorism. It is the legal responsibility of the contractor/recipient to ensure compliance with these Executive Orders and laws. This provision must be included in all subcontracts/subawards issued under this contract/agreement.
H.5 AIDAR 752.225-70 SOURCE AND NATIONALITY REQUIREMENTS (FEB 2012) (a) Except as may be specifically approved by the Contracting Officer, the contractor must procure all commodities (e.g., equipment, materials, vehicles, supplies) and services (including commodity transportation services) in accordance with the requirements at 22 CFR Part 228 “Rules on Procurement of Commodities and Services Financed by USAID Federal Program Funds.” The authorized source for procurement is Geographic Code 937 unless otherwise specified in the schedule of this contract. Guidance on eligibility of specific goods or services may be obtained from the Contracting Officer. (b) Ineligible goods and services. The contractor must not procure any of the following goods or services under this contract: (1) Military equipment (2) Surveillance equipment (3) Commodities and services for support of police and other law enforcement activities (4) Abortion equipment and services (5) Luxury goods and gambling equipment, or (6) Weather modification equipment.
72066019Q00003 HVAC UPGRADE
16
(c) Restricted goods. The contractor must obtain prior written approval of the Contracting Officer or comply with required procedures under an applicable waiver as provided by the Contracting Officer when procuring any of the following goods or services: (1) Agricultural commodities, (2) Motor vehicles, (3) Pharmaceuticals and contraceptive items (4) Pesticides, (5) Fertilizer, (6) Used equipment, or (7) U.S. government-owned excess property. If USAID determines that the contractor has procured any of these specific restricted goods under this contract without the prior written authorization of the Contracting Officer or fails to comply with required procedures under an applicable waiver as provided by the Contracting Officer, and has received payment for such purposes, the Contracting Officer may require the contractor to refund the entire amount of the purchase. H.6 NONDISCRIMINATION (JUN 2012) FAR Part 27 and the clauses prescribed in that part prohibit contractors performing in or recruiting from the U.S. from engaging in certain discriminatory practices. USAID is committed to achieving and maintaining a diverse and representative workforce and a workplace free of discrimination. Based on law, Executive Order, and Agency policy, USAID prohibits discrimination in its own workplace on the basis of race, color, religion, sex (including pregnancy and gender identity), national origin, disability, age, veteran’s status, sexual orientation, genetic information, marital status, parental status, political affiliation, and any other conduct that does not adversely affect the performance of the employee. USAID does not tolerate any type of harassment, either sexual or nonsexual, of any employee or applicant for employment. Contractors are required to comply with the nondiscrimination requirements of the FAR. In addition, the Agency strongly encourages all its contractors (at all tiers) to develop and enforce comprehensive nondiscrimination policies for their workplaces that include protection on these expanded bases, subject to applicable law. H.7 USAID DISABILITY POLICY – ACQUISITION (DEC 2004) (a) The objectives of the USAID Disability Policy are (1) to enhance the attainment of United States foreign assistance program goals by promoting the participation and equalization of opportunities of individuals with disabilities in USAID policy, country and sector strategies, activity designs and implementation; (2) to increase awareness of issues of people with disabilities both within USAID programs and in host countries; (3) to engage other U.S. government agencies, host country counterparts, governments, implementing organizations and other donors in fostering a climate of nondiscrimination against people with disabilities; and (4) to support international advocacy for people with disabilities. The full text of the policy paper can be found at the following website: http://pdf.usaid.gov/pdf_docs/PDABQ631.pdf. (b) USAID therefore requires that the contractor not discriminate against people with disabilities in the implementation of USAID programs and that it make every effort to comply with the objectives of the USAID Disability Policy in performing this contract. To that end and within the scope of the contract, the contractor’s actions must demonstrate a comprehensive and consistent approach for including men, women and children with disabilities. [END OF SECTION H]
72066019Q00003 HVAC UPGRADE
17
SECTION I - CONTRACT CLAUSES I.1 52.252-1 SOLICITATION PROVISIONS INCORPORATED BY REFERENCE. (FEB 1998) This solicitation incorporates one or more solicitation provisions by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. The offeror is cautioned that the listed provisions may include blocks that must be completed by the offeror and submitted with its quotation or offer. In lieu of submitting the full text of those provisions, the offeror may identify the provision by paragraph identifier and provide the appropriate information with its quotation or offer. Also, the full text of a solicitation provision may be accessed electronically at this/these address(es): http://www.acquisition.gov/far/ NUMBER TITLE DATE
FEDERAL ACQUISITION REGULATION (48 CFR Chapter 1) 52.202-1 DEFINITION NOV 2013 52.203-5 COVENANT AGAINST CONTINGENT FEES MAY 2014 52.203-6 RESTRICTION ON SUBCONTRACTOR SALES TO THE GOVERNMENT SEP 2006 52.203-7 ANTI-KICKBACK PROCEDURES MAY 2014 52.203-13 CONTRACTOR CODE OF BUSINESS ETHICS AND CONDUCT APR 2010 52.203-15 WHSTLEBLOWER PROTECTIONS UNDER THE AMERICAN RECOVERY AND REINVESTMENT ACT OF 2009 JUN 2010 52.203-17 CONTRACTOR EMPLOYEE WHISTLEBLOWER RIGHTS
AND REQUIREMENT TO INFORM EMPLOYEES OF WHISTLEBLOWER RIGHTS APR 2014
52.204-7 CENTRAL CONTRACTOR REGISTRATION JUL 2013 52.209-10 PROHIBITION ON CONTRACTING WITH INVERTED DOMESTIC CORPORATION DEC 2014 52.212-5 CONTRACT TERMS AND CONDITIONS REQUIRED
IMPLEMENTING STATUTES OR EXECUTIVE ORDERS – COMMERCIAL ITEMS JUN 2014
52.213-1 FAST PAYMENT PROCEDURE MAY 2006 52.215-8 ORDER OF PRECEDENCE--UNIFORM CONTRACT FORMAT OCT 1997 52.215-14 INTEGRITY OF UNIT PRICES OCT 2010 52.216-7 ALLOWABLE COST AND PAYMENT JUN 2013 52.216-24 LIMITATION OF GOVERNMENT LIABILITY APR 1984 52.217-8 OPTION TO EXTEND SERVICES NOV 1999 52.222-3 CONVICT LABOR JUN 2003 52.222-19 CHILD LABOR – COOPERATION WITH AUTHORITIES AND REMEDIES NOV 2013 52.222-21 PROHIBITION OF SEGREGATED FACILITIES FEB 1999 52.222-26 EQUAL OPPORTUNITY MAR 2007 52.222-36 AFFIRMATIVE ACTION FOR WORKERS WITH DISABILITIES OCT 2010 52.222-40 NOTIFICATION OF EMPLOYEE RIGHTS UNDER THE
NATIONAL LABOR RELATIONS ACT DEC 2010 52.222-41 SERVICE CONTRACT LABOR STANDARD MAY 2014 52.222-44 FAIR LABOR STANDARDS ACT AND SERVICE CONTRACT LABOR STANDARD – PRICE ADJUSTMENT MAY 2014 52.222-50 COMBATING TRAFFICKING IN PERSONS FEB 2009 52.222-51 EXEMPTION FROM APPLICATION OF THE SERVICE CONTRACT ACT TO CONTRACTS FOR MAINTENANCE,
CALIBRATION, OR REPAIR OF CERTAIN EQUIPMENT – REQUIREMENTS MAY 2014
52.222-53 EXEMPTION FROM APPLICATION OF THE SERVICE CONTRACT LABOR STANDARD TO CONTRACTS FOR
72066019Q00003 HVAC UPGRADE
18
CERTAIN SERVICES – REQUIREMENTS MAY 2014 52.222-54 EMPLOYMENT ELIGIBILITY VERIFICATION AUG 2013 52.223-18 ENCOURAGING CONTRACTOR POLICIES TO BAN TEXT
MESSAGING WHILE DRIVING AUG 2011 52.225-13 RESTRICTIONS ON CERTAIN FOREIGN PURCHASES JUN 2008 52.225-14 INCONSISTENCY BETWEEN ENGLISH VERSION AND
TRANSLATION OF CONTRACT FEB 2000 52.225-25 PROHIBITION ON CONTRADCTING WITH ENTITIES
ENGAGING IN CERTAIN ACTIVITIES OR TRANSACTIONS RELATING TO IRAN – REPRESENTATIONS AND CERTIFICATIONS DEC 2012
52.226-4 NOTICE OF DISASTER OR EMERGENCY AREA SET-ASIDE NOV 2007 52.232-8 DISCOUNTS FOR PROMPT PAYMENT FEB 2002 52.232-16 PROGRESS PAYMENTS APR 2012 52.232-23 ASSIGNMENT OF CLAIMS MAY 2014 52.232-29 TERMS FOR FINANCING OF PURCHASES OF COMMERCIAL ITEMS FEB 2002 52.232-33 PAYMENT BY ELECTRONIC FUNDS TRANSFER – CENTRAL CONTRACTOR REGISTRATION JUL 2013 52.232-34 PAYMENT BY ELECTRONIC FUNDS TRANSFER – OTHER THAN CENTRAL CONTRACTOR REGISTRATION JUL 2013 52.232-39 UNENFORCEABILITY OF UNAUTHORIZED OBLIGATIONS JUN 2013 52.233-3 PROTEST AFTER AWARD AUG 1996
ALTERNATE I JUN 1985 52.233-4 APPLICABLE LAW FOR BREACH OF CONTRACT CLAIM OCT 2004 52.243-1 CHANGES--FIXED PRICE AUG 1987 ALTERNATE I APR 1984 52.244-6 SUBCONTRACTS FOR COMMERCIAL ITEMS MAY 2014 52.249-4 TERMINATION FOR CONVENIENCE OF THE GOVERNMENT
(SERVICES) (SHORT FORM) APR 1984 52.249-8 DEFAULT (FIXED-PRICE SUPPLY AND SERVICE) APR 1984 52.249-14 EXCUSABLE DELAYS APR 1984 752.202-1 DEFINITIONS JAN 1990 752.204-2 SECURITY REQUIREMENTS 752.209-71 ORGANIZATIONAL CONFLICTS OF INTEREST DISCOVERED AFTER AWARD JUN 1993 752.242-70 PERIODIC PROGRESS REPORTS OCT 2007 752.7006 NOTICES APR 1984 752.7008 USE OF GOVERNMENT FACILITIES OR PERSONNEL APR 1984 752.7009 MARKING JAN 10993 752.7010 CONVERSION OF U.S. DOLLARS TO LOCAL CURRENCY APR 1984 752.7013 CONTRACTOR-MISSION RELATIONSHIPS OCT 1989 752.7025 APPROVALS APR 1984 I.2 FAR 52.217-9 OPTION TO EXTEND THE TERM OF THE CONTRACT (MAR 2000)
a) The Government may extend the term of this contract by written notice to the Contractor within 60 days; provided that the Government gives the Contractor a preliminary written notice of its intent to extend at least 60 days before the contract expires. The preliminary notice does not commit the Government to an extension.
b) If the Government exercises this option, the extended contract shall be considered to include this option clause. c) The total duration of this contract, including the exercise of any options under this clause, shall not exceed six years.
I.3 FAR 52.232-25 PROMPT PAYMENT (JULY 2013)
72066019Q00003 HVAC UPGRADE
19
Notwithstanding any other payment clause in this contract, the Government will make invoice payments under the terms and conditions specified in this clause. The Government considers payment as being made on the day a check is dated or the date of an electronic funds transfer (EFT). Definitions of pertinent terms are set forth in sections 2.101, 32.001, and 32.902 of the Federal Acquisition Regulation. All days referred to in this clause are calendar days, unless otherwise specified. (However, see subparagraph (a)(4) of this clause concerning payments due on Saturdays, Sundays, and legal holidays.)
(a) Invoice payments --
(1) Due date.
(i) Except as indicated in paragraphs (a)(2) and (c) of this clause, the due date for making invoice payments by the designated payment office shall be the later of the following two events:
(A) The 30th day after the designated billing office receives a proper invoice from the Contractor (except as provided in paragraph (a)(1)(ii) of this clause).
(B) The 30th day after Government acceptance of supplies delivered or services performed. For a final invoice, when the payment amount is subject to contract settlement actions, acceptance is deemed to occur on the effective date of the contract settlement.
(ii) If the designated billing office fails to annotate the invoice with the actual date of receipt at the time of receipt, the invoice payment due date is the 30th day after the date of the Contractor’s invoice; provided the designated billing office receives a proper invoice and there is no disagreement over quantity, quality, or Contractor compliance with contract requirements.
(2) Certain food products and other payments.
(i) Due dates on Contractor invoices for meat, meat food products, or fish; perishable agricultural commodities; and dairy products, edible fats or oils, and food products prepared from edible fats or oils are --
(A) For meat or meat food products, as defined in section 2(a)(3) of the Packers and Stockyard Act of 1921 (7 U.S.C. 182(3)), and as further defined in Pub. L. 98-181, including any edible fresh or frozen poultry meat, any perishable poultry meat food product, fresh eggs, and any perishable egg product, as close as possible to, but not later than, the 7th day after product delivery.
(B) For fresh or frozen fish, as defined in section 204(3) of the Fish and Seafood Promotion Act of 1986 (16 U.S.C. 4003(3)), as close as possible to, but not later than, the 7th day after product delivery.
(C) For perishable agricultural commodities, as defined in section 1(4) of the Perishable Agricultural Commodities Act of 1930 (7 U.S.C. 499a(4)), as close as possible to, but not later than, the 10th day after product delivery, unless another date is specified in the contract.
(D) For dairy products, as defined in section 111(e) of the Dairy Production Stabilization Act of 1983 (7 U.S.C. 4502(e)), edible fats or oils, and food products prepared from edible fats or oils, as close as possible to, but not later than, the 10th day after the date on which a proper invoice has been received. Liquid milk, cheese, certain processed cheese products, butter, yogurt, ice cream, mayonnaise, salad dressings, and other similar products, fall within this classification. Nothing in the Act limits this classification to refrigerated products. When questions arise regarding the proper classification of a specific product, prevailing industry practices will be followed in specifying a contract payment due date. The burden of proof that a classification of a specific product is, in fact, prevailing industry practice is upon the Contractor making the representation.
72066019Q00003 HVAC UPGRADE
20
(ii) If the contract does not require submission of an invoice for payment (e.g., periodic lease payments), the due date will be as specified in the contract.
(3) Contractor’s invoice. The Contractor shall prepare and submit invoices to the designated billing office specified in the contract. A proper invoice must include the items listed in paragraphs (a)(3)(i) through (a)(3)(x) of this clause. If the invoice does not comply with these requirements, the designated billing office will return it within 7 days after receipt (3 days for meat, meat food products, or fish; 5 days for perishable agricultural commodities, dairy products, edible fats or oils, and food products prepared from edible fats or oils), with the reasons why it is not a proper invoice. The Government will take into account untimely notification when computing any interest penalty owed the Contractor.
(i) Name and address of the Contractor.
(ii) Invoice date and invoice number. (The Contractor should date invoices as close as possible to the date of the mailing or transmission.)
(iii) Contract number or other authorization for supplies delivered or services performed (including order number and contract line item number).
(iv) Description, quantity, unit of measure, unit price, and extended price of supplies delivered or services performed.
(v) Shipping and payment terms (e.g., shipment number and date of shipment, discount for prompt payment terms). Bill of lading number and weight of shipment will be shown for shipments on Government bills of lading.
(vi) Name and address of Contractor official to whom payment is to be sent (must be the same as that in the contract or in a proper notice of assignment).
(vii) Name (where practicable), title, phone number, and mailing address of person to notify in the event of a defective invoice.
(viii) Taxpayer Identification Number (TIN). The Contractor shall include its TIN on the invoice only if required elsewhere in this contract.
(ix) Electronic funds transfer (EFT) banking information.
(A) The Contractor shall include EFT banking information on the invoice only if required elsewhere in this contract.
(B) If EFT banking information is not required to be on the invoice, in order for the invoice to be a proper invoice, the Contractor shall have submitted correct EFT banking information in accordance with the applicable solicitation provision (e.g., 52.232-38, Submission of Electronic Funds Transfer Information with Offer), contract clause (e.g., 52.232-33, Payment by Electronic funds Transfer— System for Award Management, or 52.232-34, Payment by Electronic Funds Transfer--Other Than System for Award Management), or applicable agency procedures.
(C) EFT banking information is not required if the Government waived the requirement to pay by EFT.
(x) Any other information or documentation required by the contract (e.g.. evidence of shipment.)
(4) Interest penalty. The designated payment office will pay an interest penalty automatically, without request from the Contractor, if payment is not made by the due date and the conditions listed in paragraphs (a)(4)(i) through (a)(4)(iii) of this clause are met, if applicable. However, when the due date falls on a Saturday, Sunday, or legal holiday, the designated payment office may make payment on the following working day without incurring a late payment interest penalty.
72066019Q00003 HVAC UPGRADE
21
(i) The designated billing office received a proper invoice.
(ii) The Government processed a receiving report or other Government documentation authorizing payment, and there was no disagreement over quantity, quality, or Contractor compliance with any contract term or condition.
(iii) In the case of a final invoice for any balance of funds due the Contractor for supplies delivered or services performed, the amount was not subject to further contract settlement actions between the Government and the Contractor.
(5) Computing penalty amount. The Government will compute the interest penalty in accordance with Office of Management and Budget prompt payment regulations at 5 CFR part 1315.
(i) For the sole purpose of computing an interest penalty that might be due the Contractor, Government acceptance is deemed to occur constructively on the 7th day (unless otherwise specified in this contract) after the Contractor delivers the supplies or performs the services in accordance with the terms and conditions of the contract, unless there is a disagreement over quantity, quality, or Contractor compliance with a contract provision. If actual acceptance occurs within the constructive acceptance period, the Government will base the determination of an interest penalty on the actual date of acceptance. The constructive acceptance requirement does not, however, compel Government officials to accept supplies or services, perform contract administration functions, or make payment prior to fulfilling their responsibilities.
(ii) The prompt payment regulations at 5 CFR 1315.10(c) do not require the Government to pay interest penalties if payment delays are due to disagreement between the Government and the Contractor over the payment amount or other issues involving contract compliance, or on amounts temporarily withheld or retained in accordance with the terms of the contract. The Government and the Contractor shall resolve claims involving disputes and any interest that may be payable in accordance with the clause at FAR 52.233-1, Disputes.
(6) Discounts for prompt payment. The designated payment office will pay an interest penalty automatically, without request from the Contractor, if the Government takes a discount for prompt payment improperly. The Government will calculate the interest penalty in accordance with the prompt payment regulations at 5 CFR part 1315.
(7) Additional interest penalty.
(i) The designated payment office will pay a penalty amount, calculated in accordance with the prompt payment regulations at 5 CFR part 1315 in addition to the interest penalty amount only if--
(A) The Government owes an interest penalty of $1 or more;
(B) The designated payment office does not pay the interest penalty within 10 days after the date the invoice amount is paid; and
(C) The Contractor makes a written demand to the designated payment office for additional penalty payment, in accordance with paragraph (a)(7)(ii) of this clause, postmarked not later than 40 days after the invoice amount is paid.
(ii)
(A) The Contractor shall support written demands for additional penalty payments with the following data. The Government will not request any additional data. The Contractor shall --
(1) Specifically assert that late payment interest is due under a specific invoice, and request payment of all overdue late payment interest penalty and such additional penalty as may be required;
72066019Q00003 HVAC UPGRADE
22
(2) Attach a copy of the invoice on which the unpaid late payment interest was due; and
(3) State that payment of the principal has been received, including the date of receipt.
(B) If there is no postmark or the postmark is illegible--
(1) The designated payment office that receives the demand will annotate it with the date of receipt, provided the demand is received on or before the 40th day after payment was made; or
(2) If the designated payment office fails to make the required annotation, the Government will determine the demand’s validity based on the date the Contractor has placed on the demand; provided such date is no later than the 40th day after payment was made.
(iii) The additional penalty does not apply to payments regulated by other Government regulations (e.g., payments under utility contracts subject to tariffs and regulation).
(b) Contract financing payments. If this contract provides for contract financing, the Government will make contract financing payments in accordance with the applicable contract financing clause.
(c) Fast payment procedure due dates. If this contract contains the clause at 52.213-1, Fast Payment Procedure, payments will be made within 15 days after the date of receipt of the invoice.
(d) Overpayments. If the Contractor becomes aware of a duplicate contract financing or invoice payment or that the Government has otherwise overpaid on a contract financing or invoice payment, the Contractor shall—
(1) Remit the overpayment amount to the payment office cited in the contract along with a description of the overpayment including the—
(i) Circumstances of the overpayment (e.g., duplicate payment, erroneous payment, liquidation errors, date(s) of overpayment);
(ii) Affected contract number and delivery order number if applicable;
(iii) Affected contract line item or subline item, if applicable; and
(iv) Contractor point of contact.
(2) Provide a copy of the remittance and supporting documentation to the Contracting Officer.
I.4 752.211-70 Language and measurement. (JUN 1992) (a) The English language shall be used in all written communications between the parties under this contract with respect to services to be rendered and with respect to all documents prepared by the contractor except as otherwise provided in the contract or as authorized by the contracting officer. (b) Wherever measurements are required or authorized, they shall be made, computed, and recorded in metric system units of measurement, unless otherwise authorized by USAID in writing when it has found that such usage is impractical or is likely to cause U.S. firms to experience significant inefficiencies or the loss of markets. Where the metric system is not the predominant standard for a particular application, measurements may be expressed in both the metric and the traditional equivalent units, provided the metric units are listed first.
72066019Q00003 HVAC UPGRADE
23
[END OF SECTION I] SECTION J: LIST OF ATTACHMENTS
1. Biographical Data Sheet – AID 1420 -17, please see the following link www.usaid.gov/forms. The form can be downloaded from the following website. The Bio-data sheet should be signed by employee and its employer both.
2. CONTRACTOR/SUBCONTRACTOR PAST INFORMATION SHEET The Offeror shall provide past performance information in the sheet provided at the end of Solicitation as Attachment 2.
3. Exhibit A – SOW – Variable Refrigerant Volume (VRV/F) System 4. Exhibit B – Project Orientation & Existing Photos 5. Exhibit C – Proposed Work BOQ 6. Exhibit D – BOD Equipment Data Sheets
[END OF SECTION J] SECTION K: REPRESENTATIONS, CERTIFICATIONS, AND OTHER STATEMENTS OF OFFERORS OR RESPONDENTS. http://www.acq.osd.mil/dpap/ccap/cc/jcchb/Files/Topical/NAF_and_Concessionaire/resources/naf_reps_and_certs.pdf 52.225-25 Prohibition on Engaging in Sanctioned Activities Relating to Iran-Certification. (DEC 2012) [END OF SECTION K]
72066019Q00003 HVAC UPGRADE
24
SECTION L INSTRUCTIONS, CONDITIONS, AND NOTICES TO OFFERORS
L.1 FAR 52.252-1 SOLICITATION PROVISIONS INCORPORATED BY REFERENCE (FEB 1998) This solicitation incorporates one or more solicitation provisions by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. The offeror is cautioned that the listed provisions may include blocks that must be completed by the offeror and submitted with its quotation or offer. In lieu of submitting the full text of those provisions, the offeror may identify the provision by paragraph identifier and provide the appropriate information with its quotation or offer. Also, the full text of a solicitation provision may be accessed electronically at this/these address (es): http://arnet.gov/far/ (FAR) http://www.usaid.gov/pubs/ads/300/aidar.pdf (AIDAR); a Word version of the AIDAR is also available at http://www.usaid.gov/pubs/ads/300.
L.2 FAR 52.204-6 DATA UNIVERSAL NUMBERING SYSTEM (DUNS) NUMBER (JULY 2013)
(a) Definition. “Data Universal Numbering System (DUNS) number”, as used in this provision, means the 9-digit number assigned by Dun and Bradstreet, Inc. (D&B) to identify unique business entities, which is used as the identification number for Federal Contractors.
(b) The offeror shall enter, in the block with its name and address on the cover page of its offer, the annotation “DUNS” or “DUNS+4” followed by the DUNS number or “DUNS+4” that identifies the offeror’s name and address exactly as stated in the offer. The DUNS number is a nine-digit number assigned by Dun and Bradstreet, Inc. The DUNS+4 is the DUNS number plus a 4-character suffix that may be assigned at the discretion of the offeror to establish additional System for Award Management records for identifying alternative Electronic Funds Transfer (EFT) accounts (see subpart 32.11) for the same concern.
(c) If the offeror does not have a DUNS number, it should contact Dun and Bradstreet directly to obtain one. (1) An offeror may obtain a DUNS number—
(i) Via the Internet at http://fedgov.dnb.com/webform or if the offeror does not have internet access, it may call Dun and Bradstreet at 1-866-705-5711 if located within the United States; or
(ii) If located outside the United States, by contacting the local Dun and Bradstreet office. The offeror should indicate that it is an offeror for a U.S. Government contract when contacting the local Dun and Bradstreet office.
(2) The offeror should be prepared to provide the following information: (i) Company legal business name. (ii) Tradestyle, doing business, or other name by which your entity is commonly recognized. (iii) Company physical street address, city, state and ZIP Code. (iv) Company mailing address, city, state and ZIP Code (if separate from physical). (v) Company telephone number. (vi) Date the company was started. (vii) Number of employees at your location. (viii) Chief executive officer/key manager. (ix) Line of business (industry). (x) Company Headquarters name and address (reporting relationship within your entity).
L3 All applicants must register/update their company’s profile in SAM as soon as possible. The link to access the SAM website is: https://www.sam.gov/portal/public/SAM/. The System for Award Management (SAM) is the Official U.S. Government system that consolidated the capabilities of CCR/FedReg, ORCA, and EPLS. There is NO fee to register for this site. Entities may register at no cost directly from this page. User guides and webinars are available under the Help tab. Applicants may submit applications under this RFA without SAM Registration. However, the apparently successful applicant will be required to register and must submit evidence of registration to USAID. Therefore, applicants are encouraged to register with SAM early so that, if selected, award will not be delayed. Note: Award will not be possible if the applicant is not registered in SAM.
72066019Q00003 HVAC UPGRADE
25
L.4 FAR 52.215-1 INSTRUCTIONS TO OFFERORS-COMPETITIVE ACQUISITION (JAN 2004)
a) Definitions. As used in this provision-- “Discussions” are negotiations that occur after establishment of the competitive range that may, at the Contracting Officer's discretion, result in the offeror being allowed to revise its proposal. In writing, writing, or written means any worded or numbered expression that can be read, reproduced, and later communicated, and includes electronically transmitted and stored information. “Proposal modification” is a change made to a proposal before the solicitation's closing date and time, or made in response to an, or made to correct a mistake at any time before award. “Proposal revision” is a change to a proposal made after the solicitation closing date, at the request of or as allowed by a Contracting Officer as the result of negotiations. “Time,” if stated as a number of days, is calculated using calendar days otherwise specified, and will include Saturdays, Sundays, and legal holidays. If however the last day falls on a Saturday, Sunday, or legal holiday, then the period shall the next working day.
b) Amendments to solicitations. If this solicitation is amended, all terms and conditions that are not amended remain unchanged. Offerors shall acknowledge receipt of any amendment to this solicitation by the date and time specified in the amendment(s).
c) Submission, modification, revision, and withdrawal of proposals. (1) Electronic submission of proposals shall be sent to:
Mr.Boris Kabeya at [email protected] Priscilla Sampil at [email protected] No Hard Copy proposals will be accepted. (2) The first page of the proposal must show—
(i) The solicitation number;
(ii) The name, address, and telephone and electronic addresses of the offeror;
(iii) A statement specifying the extent of agreement with all terms, conditions, and provisions included in the solicitation and agreement to furnish any or all items upon which prices are offered at the price set opposite each item;
(iv) Names, titles, and telephone and electronic addresses of persons authorized to negotiate on the offeror's behalf with the Government in connection with this solicitation; and
(v) Name, title, and signature of person authorized to sign the proposal. Proposals signed by an agent shall be accompanied by evidence of that agent's authority.
(3) Submission, modification, revision, and withdrawal of proposals.
(i) Offerors are responsible for submitting proposals, and any modifications or revisions so as to reach the Government office designated in the solicitation by the time specified on the cover page of this solicitation.
(ii) (A) Any proposal, modification or revision received after the exact time specified for receipt of offers is “late” and will not be considered unless it is the only proposal received or the Contracting Officers deems
72066019Q00003 HVAC UPGRADE
26
acceptance of that proposal advantageous to the Government.
(B) However, a late modification of an otherwise successful proposal that makes its terms more favorable to the Government will be considered at any time it is received and may be accepted.
(4) Unless otherwise specified in the solicitation, the offeror may propose to provide any item or combination of items. (5) Offerors shall submit proposals in response to this solicitation in English and in USD. (6) Offerors may submit modifications to their proposals at any time before the solicitation closing date and time, and may submit modifications in response to an amendment, or to correct a mistake at any time before award. (7) Offerors may submit revised proposals only if requested or allowed by the Contracting Officer. (8) Proposals may be withdrawn at any time before award. Withdrawals are effective upon receipt of notice by the Contracting Officer.
d) Offer expiration date. Proposals in response to this solicitation will be valid for 30 days from their date of receipt.
e) (e) Restriction on disclosure and use of data. Offerors that include in their proposals data that they do not want disclosed to the public for any purpose, or used by the Government except for evaluation purposes, shall- (1) Mark the title page with the following legend: This proposal includes data that shall not be disclosed outside the Government and shall not be duplicated, used, or disclosed--in whole or in part—for any purpose other than to evaluate this proposal. If, however, a contract is awarded to this offeror as a result of--or in connection with--the submission of this data, the Government shall have the right to duplicate, use, or disclose the data to the extent provided in the resulting contract. This restriction does not limit the Government's right to use information contained in this data if it is obtained from another source without restriction. The data subject to this restriction are contained in sheets [insert numbers or other identification of sheets]; and (2) Mark each sheet of data it wishes to restrict with the following legend: Use or disclosure of data contained on this sheet is subject to the restriction on the title page of this proposal.
f) Contract award. (1) The Government intends to award a contract resulting from this solicitation to the responsible offeror(s) whose proposal(s) represents the best value after evaluation in accordance with the factors and sub-factors in the solicitation. (2) The Government may reject any or all proposals if such action is in the Government's interest. (3) The Government may waive informalities and minor irregularities in proposals received. (4) The Government intends to evaluate proposals and award a contract without discussions with offerors (except clarifications as described in FAR 15.306(a)). Therefore, the offeror's initial proposal should contain the offeror's best terms from a cost or price and technical standpoint. The Government reserves the right to conduct discussions if the Contracting Officer later determines them to be necessary. If the Contracting Officer determines that the number of proposals that would otherwise be in the competitive range exceeds the number at which an efficient competition can be conducted, the Contracting Officer may limit the number of proposals in the competitive range to the greatest number that will permit an efficient competition among the most highly rated proposals. (5) The Government reserves the right to make an award on any item for a quantity less than the quantity offered, at the unit cost or prices offered, unless the offeror specifies otherwise in the proposal. (6) The Government reserves the right to make multiple awards if, after considering the additional administrative
72066019Q00003 HVAC UPGRADE
27
costs, it is in the Government's best interest to do so. (7) Exchanges with offerors after receipt of a proposal do not constitute a rejection or counter offer by the Government. (8) The Government may determine that a proposal is unacceptable if the prices proposed are materially unbalanced between line items or sub-line items. Unbalanced pricing exists when, despite an acceptable total evaluated price, the price of one or more contract line items is significantly overstated or understated as indicated by the application of cost or price analysis techniques. A proposal may be rejected if the Contracting officer determines that the lack of balance poses an unacceptable risk to the Government. (9) If a cost realism analysis is performed, cost realism may be considered by the source selection authority in evaluating performance or schedule risk. (10) If a post-award debriefing is given to requesting offerors, the Government shall disclose the following information, if applicable: (i) The agency's evaluation of the significant weak or deficient factors in the debriefed offeror's offer. (ii) The overall evaluated cost or price and technical rating of the successful and the debriefed offeror and past performance information on the debriefed offeror. (iii) The overall ranking of all offerors, when any ranking was developed by the agency during source selection.
(iv) A summary of the rationale for award. (v) For acquisitions of commercial items, the make and model of the item to be delivered by the successful offeror. (vi) Reasonable responses to relevant questions posed by the debriefed offeror as to whether source-selection procedures set forth in the solicitation, applicable regulations, and other applicable authorities were followed by the agency. FAR 52.215-1Alternate I (Oct 1997). As prescribed in FAR 15.209(a)(1), substitute the following paragraph (f)(4) for paragraph (f)(4) of the basic provision: L.5 FAR 52.216-1 TYPE OF CONTRACT (APR 1984) The Government contemplates Firm Fixed Price Contract resulting from this solicitation. L.6 FAR 52.233-2 SERVICE OF PROTEST (SEPT 2006) L.7 ACQUISITION SCHEDULE The schedule for this acquisition is anticipated to be as follows: Action Anticipated Date RFP Issued June 10, 2019 SITE VISIT/Visibility Analysis Offerors Questions Closing Date and Time
June 17-18, 2019 June 20, 2019
USAID Answers to Questions Provided June 26, 2019 Technical and Cost Proposals Closing Date and Time July 5, 2019 L.8 GENERAL INSTRUCTIONS TO OFFERORS
(a) RFP Instructions: If an offeror does not follow the instructions set forth herein, the offeror’s proposal may be
72066019Q00003 HVAC UPGRADE
28
eliminated from further consideration or the proposal may be down-graded and not receive full or partial credit under the applicable evaluation criteria.
(b) Accurate and Complete Information: Offerors must set forth full, accurate and complete information as required by this RFP. The penalty for making false statements to the Government is prescribed in 18 U.S.C. 1001.
(c) Pre-award Survey: USAID reserves the right to perform a pre-award survey which may include, but is not limited to: (1) interviews with individuals to establish their ability to perform contract duties; (2) a review of the contractor’s operations and financial system and their business and personnel procedures; and (3) site visits to the offerors institutions. Accordingly, offerors should submit their best proposal initially.
(d) Government Obligation: The U.S. Government is not obligated to make an award or to pay for any costs incurred by
the offeror in preparation of a proposal in response hereto. (e) Offer Acceptability. The Government may determine an offer to be unacceptable if the offer does not comply with
all of the terms and conditions of the RFP and prospective contract: (1) Completion of Standard Form 33, Blocks 12 through 18;
(2) Submission of proposed costs/prices and indirect cost information as required by Section B of this RFP;
(3) Completion of the "Representations, Certifications, and Other Statements of Offerors" in Section K; and
(4) Submission of information required by Section L or any other section of this RFP. The submission of these items in accordance with these instructions will, if the Government accepts the offer, contractually bind the Government and the successful Offeror to the terms and conditions of the prospective contract. Offerors shall follow the instructions contained in this RFP and supply all information and signature/certifications, as required, including whether or not the Offeror has a Secret level security clearance.
(f) Proposal Preparation Costs. The U.S. Government will not pay for any proposal preparation costs. (g) Proposals shall remain available for acceptance by USAID for a minimum of thirty days (30) days.
L.9 PROPOSAL DELIVERY INSTRUCTIONS
(a) Questions and Clarifications (i) Offerors must submit all questions regarding this solicitation to only the individuals indicated on the cover letter of
this solicitation. Offerors must submit these questions via e-mail no later than the date and time indicated in Section L.7 “Acquisition Schedule”.
(ii) USAID will not accept any questions after this date unless otherwise provided in an amendment to the solicitation.
Offerors must not submit questions to any other USAID staff.
(b) Proposals shall be submitted in two separate volumes: (a) technical, and (b) cost via electronic method only. Paper copy will not be accepted.
(c) Submission of Proposals by E-mail:
For electronic submissions, your organization must ensure that the proposals are received at [email protected] and [email protected] in their entirety. No addition or modifications will be accepted after the submission date. E-mail attachments should be formatted in Microsoft Word and/or Microsoft Excel format with 10 MB limit per e-mail. Please convert your documents to one of these formats before sending them to USAID/DRC., or provide scanned copies of pages in .pdf format (Adobe PDF) if they include signatures or forms.
In addition to the aforementioned guidelines, offerors are requested to take note of the following: i. Proposals submitted electronically must be in either Microsoft Word (for narrative text) or Excel (for tables), unless
you are providing scanned copies of pages that include signatures or forms.
72066019Q00003 HVAC UPGRADE
29
ii. After you have sent your proposals electronically, please immediately check your own email to confirm that the
attachments you intended to send were indeed sent. If you discover an error in your transmission, please send the material again and note in the subject line of the email or indicate in the file name that it is a "corrected" submission.
iii. Please do not send the same email more than once unless there has been a change, and if so, please note that it is a
“corrected” email.
iv. If you send your proposal by multiple emails, please indicate in the subject line of the email whether the email relates to the technical or cost proposal, and the desired sequence of multiple emails (if more than one is sent) and of attachments (e.g. "no. 1 of 4", etc.). For example, if your cost proposal is being sent in two emails, the first email should have a subject line which says: "[organization name], Cost Proposal, Part 1 of 2".
Our preference is that the technical and cost proposals be submitted as single email attachments, e.g. that you consolidate the various parts of a technical proposal into a single document before sending them. If this is not possible, please provide instructions on how to collate the attachments. USAID/DRC will not be responsible for errors in compiling electronic proposals if no instructions are provided or are unclear.
(d) Deadline for questions: The deadline for submitting questions’ regarding this RFP is June 20, 2019. All Questions relating to this RFP must be submitted to Boris Kabeya via email at [email protected]. Unless otherwise notified by an amendment to the RFP, no questions will be accepted after this date. Offerors must not submit questions to any other USAID staff, including the technical office.
( e) Closing Date and Time: the proposal in response to this solicitation shall be submitted to Boris Kabeya at [email protected] and Priscilla Sampil at [email protected] no later than July 5, 2019, 17.00 PM Kinshasa Time. Proposals received after this time either by email or paper submission shall not be included for evaluation.
L.10 INSTRUCTIONS FOR THE PREPARATION OF THE TECHNICAL PROPOSAL
(a) The Technical Proposal in response to this solicitation should address how the Offeror intends to perform the Statement of Work contained in Section C. The technical proposal should be organized by the technical evaluation criteria in Section M in the following format:
• Executive summary • Technical approach- Product and Services • Staffing Plan including Key Personnel • Contractor Performance Information
The technical proposal should be specific, clear, and complete.
Note: A page in the technical proposal, which contains a table, chart, graph, level of effort matrices etc., not otherwise excluded below, is subject to the “page” limitation. The following attachments are authorized and will not be counted towards the 10 page limitation: • Cover/Title Page; • Table of Contents; • Dividers; • Table summarizing qualifications of proposed personnel
• Appendix attachments which contain biographical information (i.e., resumes/CVs and other documentation provided by the Offeror) for proposed candidates; • Contractor/Sub-Contractor Past Performance Listing; and • Charts, such as Management Structure Organizational Chart(s), etc. • Partners Commitment/Collaboration letters • Key Personnel commitment letters • Analysis supporting tables
72066019Q00003 HVAC UPGRADE
30
• Contract Past Performance Report Short-Forms, and Summary Table All critical information from appendices must be summarized in the technical proposal. L.10.1. Technical Approach (see section M.3.1)
The extent to which the proposal demonstrates understanding and familiarity with the tasks and services described in the Scope of Work. The extent to which the contractor presents its approach and proposed methodology to implementing the scope of work. As part of this section, the offeror must include information on how it would evaluate the requested services on a yearly basis. L.10.2 Staffing Plan including Key Personnel. (See M.3.2) The offerors proposed staff shall be evaluated in accordance with the skills and expertise (see section F and Evaluation Criteria M.3. Demonstrate availability of technical staff at all times The offeror shall include a brief summary for each Key Personnel not to exceed one page including the extent and nature of key personnel’s experience in implementing similar projects. Detailed CV/Resume should be provided in an Annex (not to be counted in page limit) but not to exceed four pages in length and shall be in chronological order starting with most recent experience. Resume/CVs should also include a minimum of three (3) references of professional contacts with their contact information (name, title, organization, phone number, email address). Each resume shall be accompanied by a signed letter of commitment from each candidate including statement of (a) availability to start work as proposed by the offeror and (b) intention to serve for the stated term of the service. In addition, the key personnel should possess strong communication and interpersonal skills in English. L.10.3 CONTRACTOR PERFORMANCE INFORMATION [See Section M.3.3]
(a) The offeror (including all partners of a joint venture) must provide performance information for itself and
subcontractor in accordance with the following:
1. List in an annex to the technical proposal minimum 3 and maximum up to 5 of the most recent and relevant contracts for efforts similar to the work in the subject proposal. The most relevant indicators of performance are contracts of similar scope of work in trade facilitation and economic and private sector development related activities.
2. Provide for each of the contracts listed above a list of contact names, job titles, mailing addresses, phone
numbers, e-mail addresses, and a description of the performance to include: • Scope of work or complexity/diversity of tasks, • Primary location(s) of work, • Term of performance, • Skills/expertise required, • Dollar value, and • Contract type, i.e., fixed-price, cost reimbursement, etc. (USAID recommends that you alert the contacts that their names have been submitted and that they are authorized to provide performance information concerning the listed contracts if and when USAID requests it.)
(b) If extraordinary problems impacted any of the referenced contracts, provide a short explanation and the
corrective action taken (FAR 15.305(a)(2)).
72066019Q00003 HVAC UPGRADE
31
(c) Describe any quality awards or certifications that indicate exceptional capacity to provide the service or product described in the statement of work. This information is not included in the page limitation.
(d) Performance in Using Small Business (SB) Concerns (as defined in FAR 19.001)
(1) This section (d) is not applicable to offers from small business concerns. (2) As part of the evaluation of performance in Section M.4 of this solicitation, USAID will evaluate the extent
you used and promoted the use of small business concerns under current and prior contracts. The evaluation will assess the extent small business concerns participated in these contracts relative to the size/value of the contracts, the complexity and variety of the work small business concerns performed, and compliance with your SB subcontracting plan or other similar small business incentive programs set out in your contract(s).
(3) In order for USAID to fully and fairly evaluate performance in this area, all offerors who are not small
business concerns must do the following: (A) Provide a narrative summary of your organization's use of small business concerns over the past three years.
Describe how you actually use small businesses--as subcontractors, as joint venture partners, through other teaming arrangements, etc. Explain the nature of the work small businesses performed--substantive technical professional services, administrative support, logistics support, etc. Describe the extent of your compliance with your SB subcontracting plan(s) or other similar SB incentive programs set out in your contract(s) and explain any mitigating circumstances if goals were not achieved.
(B) To supplement the narrative summary in (A), provide a list of the recent [CO to establish the timeframe for
“recent” while keeping in mind that the number of reports could be significant over an extended period of time.] contracts for which you submitted subcontract reports to eSRS (FAR 52.219-9(d)(10) and a copy of any similarly recent subcontracting reports if they were not submitted to eSRS.
(C) Provide the names and addresses of three SB concerns for us to contact for their assessment of your
performance in using SB concerns. Provide a brief summary of the type of work each SB concern provided to your organization, and the name of a contact person, his/her title, phone number, and e-mail address for each. L.11. 1 INSTRUCTIONS FOR THE PREPARATION OF THE COST PROPOSAL: The offeror shall clearly show how they arrived at the firm fixed-price for the work to be accomplished. A Cost proposal must include:
• The overall cost of the service (material and labor) (b ) Prospective Contractors shall submit Proof of financial capability to pre-finance all costs, all risks, loss, and damage. The offerors are requested to provide the Cost proposal in the following budget format.
LINE ITEM COST Removal of the existing HVAC Equipment Installation of a new system Others TOTAL
Please note: there is no page limit for cost proposal.
72066019Q00003 HVAC UPGRADE
32
L.12 Evidence of Responsibility for prime and subcontractor if any
(a) The offeror must submit sufficient evidence of responsibility for the contracting officer to make an affirmative determination of responsibility pursuant to the requirements of FAR § 9.104-1. Accordingly, prime offerors must seriously address each element of responsibility. To be determined responsible, a prospective contractor must:
(1) Have adequate financial resources to perform the contract, or the ability to obtain them (see FAR 9.104-3(a)); (2) Be able to comply with the required or proposed delivery or performance schedule, taking
into consideration all existing commercial and governmental commitments; (3) Have a satisfactory performance record (See FAR 9.104-3(b) and Subpart 42.15). An Offeror shall not be determined
responsible or non-responsible solely on the basis of a lack of relevant performance history, except as provided in FAR 9.104-2;
(4) Have a satisfactory record of integrity and business ethics; (5) Have the necessary organization, experience, accounting and operational controls, and technical skills, or the ability
to obtain them (including, as appropriate, such elements as production control procedures, property control systems, quality assurance measures, and safety programs applicable to materials to be produced or services to be performed by the prospective Contractor and subcontractors). (See FAR 9.104-3(a));
(6) Have the necessary production, construction, and technical equipment and facilities, or the ability to obtain them (See
FAR 9.104- 3(a)); and (7) Be otherwise qualified and eligible to receive an award under applicable laws and regulations (e.g., Equal
Opportunity, Clean Air and Water, Small Business Subcontracting, etc.). The responsibility information that may be requested includes, but is not limited to, audited or certified financial statements, tax returns and other financial records necessary to establish responsibility. Please note that this information is only required upon a specific request from the contracting officer or his representative. [END OF SECTION L]
72066019Q00003 HVAC UPGRADE
33
SECTION M: EVALUATION FACTORS FOR AWARD
M.1 GENERAL INFORMATION
(a) The Government may award a contract without discussions with offerors in accordance with FAR 52.215-1. (b) The Government intends to evaluate offerors in accordance with Section M of this RFP and make contract award to
the responsible offeror(s) whose proposal(s) represents the best value to the U.S. Government. (c) The submitted technical information will be scored by a technical evaluation committee using the technical criteria
shown below. The evaluation committee may include industry experts who are not employees of the Federal Government. When evaluating the competing offerors, the Government will consider the written qualifications/capability information provided by the offerors, and any other information obtained by the Government through its own research.
(d) In accordance with FAR 15.304(e)(1), all evaluation factors other than cost/price when combined are significantly
more important than cost/price factors. M.2 DETERMINATION OF THE COMPETITIVE RANGE AND CONTRACT AWARD
(a) The competitive range of offerors with whom negotiation may be conducted (if necessary) will be determined by the
Contracting Officer pursuant to FAR 15.306(c). (b) Competitive Range: If the Contracting Officer determines that discussions are necessary, he/she will establish a
Competitive Range composed of only the most highly rated proposals. In certain circumstances, the Contracting Officer may determine that the number of most highly rated proposals that might otherwise be included in the competitive range exceeds the number at which an efficient competition can be conducted. Should that be the case, the Contracting Officer may then limit offers in the competitive range to the greatest number that will permit an efficient competition among the most highly rated offers.
The Government may exclude an offer if it is so deficient as to essentially require a new technical proposal. The Government may exclude an offer so unreasonably priced, in relation to more competitive offers, as to appear that there will be little or no chance of becoming competitive. The Government may exclude an offer requiring extensive discussions, a complete re-write, or major revisions such as to allow an Offeror unfair advantage over those more competitive offers.
(c) Award: In accordance with FAR 52.215-1(f), the Government intends to award a contract or contracts resulting
from this solicitation to the responsible offeror(s) whose proposal(s) represent the best value after evaluation in accordance with the factors and sub-factors as set forth in this solicitation.
M.3 EVALUATION CRITERIA In determining which offer represents the best value to meet the Government’s needs, the Government shall evaluate responses using the following evaluation criteria: Technical Evaluation Criteria Weight Products and Services 60 points Staffing Plan including Key Personnel 30 points Past Performance 10 points TECHNICAL EVALUATION CRITERIA Technical, cost, and other factors will be evaluated and an award will be made on the basis of best value to the U.S.
72066019Q00003 HVAC UPGRADE
34
Government. Technical factors are considered substantially more important than cost factors.
(a) The technical proposal will be scored by a technical evaluation committee using the criteria shown in this Section. (b) The criteria below are presented by major category, with relative order of importance, so that Offerors will know
which areas require emphasis in the preparation of proposals. The criteria below reflect the requirements of this particular solicitation.
(c) Cost has not been assigned a numerical weight. Offerors are reminded that the Government is not obliged to award a
negotiated contract on the basis of lowest proposed cost, or to the Offeror with the highest technical evaluation score. Although for this procurement technical proposal merits are considered substantially more important than cost relative to deciding who might best perform the work, cost factors and USAID’s budget must also be considered. Therefore, after the final evaluation of proposals, the Contracting Officer will make the award to the Offeror whose proposal offers the best value to the Government considering both technical and cost factors. Offerors should note that the following criteria: (1) serve as the standard against which all proposals will be evaluated, and (2) serve to identify the significant matters which Offerors should address in their proposals. EVALUATION CRITERIA 1. Products and Service (60 points) The Offeror’s approach to providing consistent quality services which are conform to the technical specifications outlined in this solicitation. The ability, capability and skill of the Contractor to provide the service in accordance with the Acquisition schedule. 2. Staffing Plan including Key Personnel (30 points) USAID will evaluate how the proposed staffing plan and key personnel prepares the contractor to provide the Government with the most efficient and most effective quality services throughout the period of performance of this contract. 3. Contractor Performance Information (10 Points)
(a) Performance information will be used for both the responsibility determination and best value decision. USAID may
use performance information obtained from other than the sources identified by the offeror/subcontractor. USAID will utilize existing databases of contractor performance information and solicit additional information from the references provided in Section L. 10 of this RFP and from other sources if and when the Contracting Officer finds the existing databases to be insufficient for evaluating an offeror’s performance.
(b) Adverse past performance information to which the offeror previously has not had an opportunity to respond, will be addressed in accordance with the policies and procedures set forth in FAR 15.3.
(c) USAID will initially determine the relevance of similar performance information as a predictor of probable
performance under the subject requirement. USAID may give more weight to performance information that is considered more relevant and/or more current.
(d) The contractor performance information determined to be relevant will be evaluated in accordance with the elements
below: (1) Quality of product or service, including consistency in meeting goals and targets: 2 points (2) Cost control, including forecasting costs as well as accuracy in financial reporting (Note to COs: this element is not
required for Firm-Fixed Price or Firm-Fixed Price with Economic Price adjustment contracts) 2 points
72066019Q00003 HVAC UPGRADE
35
(3) Schedule, including the timeliness against the completion of the contract, task orders, milestones, delivery schedules, and administrative requirements (e.g., efforts that contribute to or affect the schedule variance). 2 points
(4) Business relations, addressing the history of professional behavior and overall business-like concern for the interests
of the customer, including the contractor’s history of reasonable and cooperative behavior (to include timely identification of issues in controversy), customer satisfaction, timely award and management of subcontracts, attitude in remedying problems, and timely completion of all administrative requirements- 2 points
(5) Management of key personnel, including appropriateness of personnel for the job and prompt and satisfactory
changes in personnel when problems with clients where identified: 2 points Total Weight for Performance Evaluation 10 points (f) An offeror’s performance will not be evaluated favorably or unfavorably when: (1) The offeror lacks relevant performance history, (2) Information on performance is not available, or (3) The offeror is a member of a class of offerors where there is provision not to rate the class against a sub factor.
When this occurs, an offeror lacking relevant performance history is assigned a "neutral" rating. For example, a small business prime offeror will not be evaluated on its performance in using small business concerns. If this sub factor is worth a possible 10 points out of a total possible point value of 100 for the technical proposal, then the small business prime offeror’s technical proposal will have a maximum of 90 possible points. If it was assigned a total score of 80 points out of the 90 maximum possible points, its total technical score for evaluation against the other offerors would be 88.89 (i.e., 80/90). USAID understands that there may be minor arithmetic differences in percentage terms as a result; however, it considers these differences to be minor and that they will not impact any best-value decision made under this solicitation.
An exception to this “neutral” rating provision is when a non-small businesses prime has no history of subcontracting with small business concerns. Prior to assigning a "neutral" past performance rating, the contracting officer may take into account a broad range of information related to an offeror's performance.
M.4 COST EVALUATION Evaluation points are not awarded for cost. The review of the cost proposal shall include a cost realism analysis to determine what the Government should realistically expect to pay for the proposed effort, the Offeror’s understanding of the work, and the Offeror’s ability to perform the contract. These will consist of a review of the cost portion of an Offeror’s proposal to determine if the overall costs proposed are reasonable and realistic for the work to be performed, if the costs reflect the Offeror’s understandings of the requirements, and if the costs are consistent with the technical proposal. Evaluation of cost proposals will consider but not be limited to the following:
- Cost realism and completeness of cost proposal and supporting documentation. - Cost efficiency of proposed Other Direct Costs (ODCs).
Offerors are reminded that the U.S. Government is not obligated to award a negotiated contract on the basis of the lowest proposed cost (see FAR 15.101-1) or to the Offeror with the highest technical evaluation score. For this procurement, however, technical proposal merits are considered significantly more important than cost relative to deciding who best might perform the work. Therefore, after the final evaluation of the proposals, the Contracting Officer will make the award to the Offeror whose proposal offers the best value to the Government, considering both technical and cost factors. It should be noted that estimated cost is an important factor and its importance as an evaluation factor will increase as the degree of equality of technical competence between proposals increases.
72066019Q00003 HVAC UPGRADE
36
M.5 SOURCE SELECTION
(a) The overall evaluation methodology set forth above will be used by the contracting officer as a guide in determining which proposal(s) offer the best value to the U.S. Government. In accordance with FAR 52.215 1, and as set forth in Section L of this solicitation, award will be made by the contracting officer to the responsible offeror(s) whose proposal(s) represents the best value to the U.S. Government after evaluation in accordance with all factors and sub-factors in this solicitation.
(b) This procurement utilizes the tradeoff process set forth in FAR 15.101-1. If the contracting officer determines that
competing technical proposals are essentially equal, cost/price factors may become the determining factor in source selection. Conversely, if the contracting officer determines that competing cost/price proposals are essentially equal, technical factors may become the determining factor in source selection. Further, the contracting officer may award to a higher priced offeror if a determination is made that the higher technical evaluation of that offeror merits the additional cost/price. [END OF SECTION M]
72066019Q00003 HVAC UPGRADE
37
ATTACHMENT 1: CONTRACTOR/SUBCONTRACTOR PAST INFORMATION SHEET 1. Name of Contracting Entity: 2. Contract/Agreement No.: 3. Contract/Agreement Type: 4. Amount: 5. Name of Key Personnel: 6. Description of Work/Services/Activity: 6. Problems: (If problems encountered on this contract, explain corrective action taken) 7. Contacts (Name and Telephone #): 8. Contractor: 9. Information Provided in Response to RFP No.: 10. A copy of interim or final Contractor Performance Report that have been finalized/signed by the Cognizant Contracting Officer, if any. [NOTE: when submitting above information for subcontractors, the actual dollar amount of subcontract must be listed in Block 4 instead of the Total Estimated Cost of the overall contract. In addition, offerors may submit attachments to this past performance table if the spaces provided are inadequate.]
UNCLASSIFIED
Exhibit A –
SOW – Variable Refrigerant Volume/ Flow (VRV/F) System
EXHIBIT A SOW – VRV/F System
UNCLASSIFIED
Page 1 of 13 SOW – HVAC UPGRADES
3.0 SCOPE OF WORK (VRV/VRF SYSTEM)
THIS SOW IS FOR A VARIABLE REFRIGERANT F L O W / VOLUME (VRF/V) SYSTEM IN PLACE OF THE EXISTING CONSTANT VOLUME SELF CONTAINED PACKAGE AHU’S AND INDIVIDUAL VRF SYSTEMS. IN SUMMARY, (PER EACH FLOOR) THE CONTRACTOR SHALL INSTALL NEW VRF/V HEAT PUMP OUTDOOR UNITS AND APPROXIMATELY 38 INDOOR DUCTED / CONCEALED, AND OR STANDARD WALL OR FLOOR UNITS.
3.1 Contractor shall confirm the requirements of the SOW are understood, and that
the Contractor is fully aware of the location and requirements contained therein. If the Contractor believes additional information is needed, the Contractor shall schedule additional site visits, at the Contractor’s expense, with the COR to ensure the project work requirements are established prior to submitting pricing for the project.
3.2 Scheduling:
3.2.1 Unless otherwise agreed upon, work shall only commence on one Floor at a time. The contractor shall complete work outside of the building (e.g.; line sets / electrical rough-in) to the fullest extent possible prior to beginning interior work.
3.2.2 The occupants will be temporarily relocated during the construction
effort. It is the intent of the government to reduce the project schedule and occupant disruption. While the equipment is offline and spaces unoccupied, the contractor shall be responsible for providing temporary heating / cooling equipment to protect interior finishes / piping, etc.
3.2.3 The USAID expects the interior works on each floor can be
completed within 4-5 weeks, which does not include design, equipment lead time and mechanical / electrical rough-in works that take place outside the unit. The USAID expects that the completion of the onsite works for each floor (excluding design and equipment lead time) shall be completed within 1-2 weeks of the project onsite / construction start date.
3.2.4 The contractor shall provide a detailed design and construction
schedule as a submittal with the proposal delivery.
EXHIBIT A SOW – VRV/F System
UNCLASSIFIED
Page 2 of 13 SOW – HVAC UPGRADES
3.3 General New Work Requirements
3.3.1 The new outdoor condenser units shall be located on the roof above the USAID office space. The Contractor shall verify and provide outdoor condenser units size, footprint, and weight are within suitable limits of the the existing roof structures. All equipment shall be mounted on structurally engineered housekeeping pads or structural supports. If new roof mounted equipment pads and structural supports are required, the Contractor shall submit sealed engineered drawings by a licensed structural engineer to demonstrate they are able to safely function with the existing roof system. Coordinate requirements and submittal review with the COR and with the FM
3.3.2 Provide laborers, equipment, and materials necessary to provide the work defined by the specific requirements which follow.
3.4 Drawing / Construction Document Requirements:
3.4.1 Basic Design / Construction Documents Deliverables submitted shall include, but are not limited to, the information below. The deliverable stages will include (1) 50% Design Documents, (2) 100% Construction Documents, and (3) a Final Design Issued for Construction (IFC) drawings. The contractor shall provide electronic copies of the documents for review. Deliverables shall include:
a. Site Plan: Site layout, identifying where the staging area is to be
located, vehicular access routes, crane access / staging, and location of any temporary facilities are to be located within the area.
b. Demolition Plan: Show required demolition of existing equipment.
The plan should elaborate the phases of the demolition for all the units. Contractor should also provide the plans and take special care
EXHIBIT A SOW – VRV/F System
UNCLASSIFIED
Page 3 of 13 SOW – HVAC UPGRADES
to remove the demolished material without damaging the existing interior of the units.
c. Proposed New Work: Show layout, schematic and specification of
all new equipment. Provide details and cross-sections of the proposed work as necessary to explain the project. All details shall indicate the difference between new and existing construction. Any penetration required from the exterior walls should be indicated clearly.
d. Mechanical and Plumbing Drawings: Show floor plan layout of all
new materials and equipment. Provide floor plans, cross-sections and detail drawings of the proposed work as necessary to explain the project construction and new equipment installation.
e. Electrical Drawings: Show floor plan layout of all new materials
and equipment. Provide electrical wiring diagram / risers and power panel locations. Provide load calculations for conductor and overcurrent protection.
f. Shop drawings: Shop drawings shall be provided by contractor for
official records.
g. Catalog Cuts: Identify all materials and products to be used. The specific manufacturer and model number used as the basis of design shall be listed for each item. Include maintenance and warranty information.
h. Design Calculations: Provide mechanical and electrical
calculations as specified in this SOW and included specifications. Equipment sizes shall be justified with block cooling and heating load calculations; in addition individual room heat gain/heat loss calculations will be required. Heating and cooling systems shall be sized in accordance with the ASHRAE Handbook of Fundamentals using a design set point of 21°C and >=35% relative humidity for heating and 24°C and <=60% relative humidity for cooling at the ASHRAE 1% cooling and 99% heating conditions. Safety factors in the load calculations shall not exceed 10%. The contractor will provide these calculations are part of the equipment submittal package.
i. Indoor Conditions shall be met as follows
- Noise criteria (NC Curve): NC25-NC35
EXHIBIT A SOW – VRV/F System
UNCLASSIFIED
Page 4 of 13 SOW – HVAC UPGRADES
3.5 Existing Equipment Modification / Removal / Demolition requirements:
3.5.1 The Contractor shall shut down equipment in its entirety. Isolating equipment, draining down, flushing and refilling the systems, and locking- out/tagging-out systems shall be required to safely complete the specified tasks.
3.5.2 Remove the existing AHU and ducting systems from all the units as required to install the new VRV system. Unused ductwork components may be abandoned in place if sealed and areas patched. Contractor to ensure proper patching and painting to match the existing wall / ceiling colors.
3.5.3 All components / materials removed from the units and disposal at contractor’s expense.
3.5.4 Removal shall include all associated electrical circuiting/breakers, electrical conduit/wiring, controls wiring/devices and piping that will not be used as part of the new work. Other than those specifically stated in this SOW document, no systems, equipment, or components are to be abandoned in place.
3.5.5 Existing Electrical Service: The Contractor shall evaluate the existing electrical installation during the pre-bid walk through to determine if existing conduit and/or wiring can be reused to feed the new equipment. In the bid proposal, the Contractor shall document all electrical service items being replaced and the justification for the replacement. If existing feeder cannot be reused, new electrical service must be provided. Contractor shall provide drawings for electrical upgrades, which shall include calculations, such as feeder / conduit sizing, overcurrent protection sizing, and voltage drop.
3.5.6 Recover Existing Refrigerant: The Contractor shall be responsible to
recover all existing refrigerant and handle it per the guidelines of the section 2 Refrigerant Handling sub-paragraph above.
EXHIBIT A SOW – VRV/F System
UNCLASSIFIED
Page 5 of 13 SOW – HVAC UPGRADES
3.6 New Equipment and New Work Requirements:
3.6.1 New Equipment:
a. Equipment.
- Replacement of the existing chilled water system with a Microprocessor-controlled Variable Refrigerant Flow/Volume (VRF of VRV) type HVAC System with reheat capability and Dedicated Outdoor Air System (DOAS) for ventilation purposes.
- Accepted Manufacturers: LG, Daikin, Mitsubishi, Carrier,
York, Trane, and Petra.
- Electrical: Residential compound has 380/220 Volt, 3 Phase, 50 Hz power available.
- BASIS OF DESIGN (BOD):
LG Multi V ARUM480BTE5 (Outdoor Units)
LG ARNU053TRD4, LG ARNU123L2G4,
LG ARNU123SJA4 (Indoor Units))
.
- The VRF and DOAS systems shall comply with ASHRAE Standard 15-2011 - Safety Standard for Refrigeration Systems (ANSI approved). ASHRAE Standard 15-200.
- The VRF System shall comprise of outdoor condensing units
with inverter-controlled compressors. For each indoor room / zone, provide matching / mated indoor units (all concealed / ducted units, unless otherwise approved) with associated ducting, insulation, grilles, diffusers, insulated refrigerant piping, condensate removal piping, controls, valves, and associated electrical works. The general expectation is that each floor will receive 35– 40 indoor ducted / concealed indoor units. The system as a whole
EXHIBIT A SOW – VRV/F System
UNCLASSIFIED
Page 6 of 13 SOW – HVAC UPGRADES
shall be able to cater partial load which can be as low as 10% of the total load. The contractor shall ensure all electrical requirements are met as related to the installed equipment.
- The DOAS (Dedicated Outdoor Air System) system shall be an
air handler than can be integrated with the VRV system or may be its own split system. The system shall be sized to continually condition the existing design of outdoor air flow rate to each floor. The DOAS units shall have true dehumidification (over cooled / reheat) sequences and shall have variable speed supply fans. Provide a minimum two (2) separate coils in the DOAS unit for cooling and reheating outside air. Reheat coils may consist of electric resistance reheat coils. The unit shall have a time of date (TOD) programmable controller. The DOAS supply air shall be ducted and delivered to the designated rooms on every floor, and in addition to the common / stair well areas. The DOAS unit shall have an isolation damper interlocked with the unit to close when the DOAS unit is off / de-energized. The cooling coil shall be sized for adequate total (sensible and latent) capacity appropriate for ASHRAE Dehumidification Design Condition.
- Provide DOAS unit with a minimum MERV 8 pre-filter and a
MERV 13 level final filter.
b. Outdoor Equipment Locations. The location for VRV/VRF outdoor units for the 1st and 2nd floor shall be on the roof of the USAD Office space, or suitable location designated by Post. Locations will be finalized by USAID after review of site plans.
- All manufacturer required space clearance and
tolerances to be considered for proper maintenance when planning or making the set location ready for VRV/VRF installation.
EXHIBIT A SOW – VRV/F System
UNCLASSIFIED
Page 7 of 13 SOW – HVAC UPGRADES
- All piping and support equipment shall be enclosed in SS/standard cladding material for insulated pipes.
- All hangers and supports shall be constructed of
corrosion resistant materials and coatings. Uncoated materials shall be Stainless Steel or Hot Dipped Galvanized Steel. Other materials shall be coated with a corrosion-resistant coating.
- Building access/ Main Panel shall remain at the same
location.
- Roof penetrations are to be designed and coordinated with Post/ FM.
- Adequate ballast shall be provided to ensure the
outdoor units are able to withstand the local wind conditions.
c. Indoor Equipment Locations. The general expectation is that each
floor will receive 35 – 40 indoor ducted / indoor units. Locations will be finalized by USAID after review of site plans.
- All manufacturer required space clearance and
tolerances to be considered for proper maintenance when planning or making the set location ready for VRV/VRF installation.
- All piping and support equipment shall be enclosed in
SS/standard cladding material for insulated pipes
d. Electrical. The contractor is responsible for installing new electrical infrastructure as required to support the new VRV system. Breaker and conductors shall be sized per manufacturer’s recommendations. All existing disconnects and associated wiring and connectors are to be replaced as applicable. Contractor shall verify existing overcurrent protection and conductor size feeding new equipment from main distribution panel are sized per NEC requirements to adequately support new equipment electrical loads. Where inadequately sized, replace with new.
e. High Ambient Temperature Environment. All equipment provided must be manufactured for use in a high ambient temperature
EXHIBIT A SOW – VRV/F System
UNCLASSIFIED
Page 8 of 13 SOW – HVAC UPGRADES
environment and must be constructed using the materials and/or countermeasures and/or treatments with coatings to ensure maximum duration of operation in this environment.
f. Heat Pump “Heating Operation”. All equipment provided must be
manufactured for heat pump use in the lowest ambient temperature (per ASHRAE).
g. Provide NEMA 4X or 6P type enclosures with enhanced corrosion
protection. Provide Totally Enclosed, Fan-Cooled (TEFC) and Totally Enclosed, Air Over (TEAO) electric motors. Outdoor piping shall be protected with vapor barrier and fully sealed insulation. Equipment insulation shall be flexible elastomeric with laminated jacketing resistant to punctures, tears, and UV rays. Refer to attached equipment specifications.
h. Labeling – Contractor shall provide new equipment / piping labels.
At a minimum, these labels shall indicate service type, unit, thermostat, controller, etc. name / number, and direction of flow on all new pipe and ductwork sections.
3.6.2 Installation of the New VRV/VRF system:
(1) VRV/VRF system with inverter compressors and heat/cool “heat pump” air cooled unit:
(a) To install the VRV/VRF:
(i) The contractor before doing any installation will arrange a pre installation meeting with the COR. The contractor shall have developed and obtained approval of the basic design / construction ductwork. Contractor to provide the manufacturer specified installation method. Best installation practice to maintain the manufacturer applied warranty to the new installations.
(ii) The VRV/VRF OUTDOOR units should be installed in a location
that meets the following requirements:
1. The foundation or roof structure is strong enough to support the weight of the unit and the floor is flat to prevent vibration and noise generation. The space around the unit is adequate for servicing and the minimum space for air inlet and air outlet is available as recommended by the manufacturer.
2. Shut off and tag out electrical circuits.
EXHIBIT A SOW – VRV/F System
UNCLASSIFIED
Page 9 of 13 SOW – HVAC UPGRADES
3. Cover / protect existing to remain system / components.
4. Run suitable grade of electrical power supply from the main
supply panel for all new Variable Refrigerant Volume System (VRV) unit components in accordance with local electrical practices and International Building Codes, whichever is more stringent.
5. Install electrical power supply for the indoor units and outdoor
units in accordance with local electrical practices and International Building Codes, whichever is more stringent.
6. Install the approved VRV/VRF unit at the location with
suitable seismic / shock absorbing material between machine and the steel rack with rubber damper under layer.
7. The VRV/VRF indoor and outdoor system must be designed in
accordance with VRV/VRF manufacturer installation guide.
8. The refrigerant piping must be installed by VRV/VRF manufacturer certified technicians who have minimum 5-years HVAC system installation experience.
9. All electric appliances shall be grounded/connected with the existing grounding system and if applicable with the lightning protection system.
(b) Piping and drain lines:
(i) Install piping where possible in walls and above ceilings
Access doors shall be provided for all valves, controllers, filters, junction boxes, etc.
(ii) The contractor shall patch and paint as necessary to match the
existing.
1. Open office area/rooms could have slim ceiling mounted (concealed) duct type indoor unit covered with sheetrock chase / bulkhead. These units shall have ducted supply and returns with appropriately distributed supply / return grills. Ceiling / wall cavities cannot be used as return plenums. Design team shall work closely with COR in bulk head design / unit locations. Patching and painting is required to be done for final finish and should match the existing interior.
EXHIBIT A SOW – VRV/F System
UNCLASSIFIED
Page 10 of 13 SOW – HVAC UPGRADES
2. For all other office and utility rooms could use wall
mounted type indoor units with as much possible concealed piping and accessories.
(iii)Install individual drain line for each indoor unit to discharge
condensation water to an exterior drain system as designated by the COR. Ensure code condensate slope requirement is achieved.
(iv) Install code compliant piping system to bring the condensation
water from the unit and daylight onto the ground, or the nearest floor drain, NOT onto the wall.
(v) Size of refrigerant pipe:
1. Refrigerant piping shall be sized (MFG. recommended) to
avoid excessive pressure drop of the fluids or gases they carry. Compliance with the recommendations of the American Society of Heating, Refrigeration and Air-Conditioning Engineers and other OEM manufacturer standards.
2. All pipes up to 18mm OD shall be of fully annealed copper,
refrigerant rated and refrigerant type to mention clearly on the pipes.
3. All pipes from 22mm to 108mm OD shall be of hard drawn copper refrigerant rated and refrigerant type to mention clearly on the pipes.
4. All pipes over 108mm OD shall be of black extra heavy
seamless steel pipe to ISO 2604 grade 360 and refrigerant rated.
(c) Indoor Units:
(i) Run suitable grade of electrical wire from the power supply or to
connect with the existing circuit. Contractor to provide electrical wiring schematic and provide samples for wires for approval prior to procurement and use on site.
(ii) Install the indoor unit in the area as designated by the COR or his
representative. Contract shall have developed and received approval on floor plans with unit locations and thermostat locations.
EXHIBIT A SOW – VRV/F System
UNCLASSIFIED
Page 11 of 13 SOW – HVAC UPGRADES
(iii)Provide hard wired, programmable thermostats.
(iv) Install isolation valves on each (supply and return) indoor unit. Provide access doors as required.
(v) Mark filters location for easy cleaning. Provide access doors as
required.
(2) Testing and commissioning of the VRF:
(i) Follow the manufacturer installation guide for testing and commissioning which should include the below mentioned:
1. Clean and vacuum the new VRV system.
2. Air tight test using Nitrogen; follow the manufacture specified
standards for pressure testing. Use the test method specified in the latest manufacturer installation guide.
3. Check the alignment of drain pipes/lines at a suitable drop.
4. Follow all manufacturer specified precautions and safety
requirements before charging the refrigerant.
5. Follow the manufacturer specified flow chart for the refrigerant charging.
6. Charge sufficient refrigerant, check and test again all joints for
gas leakage.
7. Check, fix and tighten for leaks if any.
8. Check and tighten all suspect loose parts if any.
9. Check if additional refrigerant charging is required.
10. Insulation of the pipes to be done after successful testing as per the manufacturer installation manual.
(ii) After refrigerant energize the system:
1. Check for abnormal noise or spark before turning on the VRF.
2. Start the main VRF. Follow manufacturer’s start-up
procedures and complete start-up documentation.
EXHIBIT A SOW – VRV/F System
UNCLASSIFIED
Page 12 of 13 SOW – HVAC UPGRADES
3. Follow the manufacturer specified start up method as
mentioned in the installation guide.
4. Set the lowest temperature and turn on the indoor units one by one for at least 30 minutes.
5. Check for abnormal noise or sound (looking for loosen parts).
6. Check the heating and cooling functions.
7. Check the main panel for any malfunction codes.
8. The Contractor shall perform test, adjust, and balance (TAB)
procedures on all newly installed equipment.
9. The Contractor shall provide formal training to the local staff, which shall include an overview of all required preventive maintenance tasks and typical troubleshooting steps. Training shall be a minimum of 8 hours, w/ four (4) hours of class room training, and four (4) hours of hands-on in front of equipment training.
(3) Documentation:
(i) Provide the USAID with all related documents / equipment / materials:
1. Owner’s manuals, instructions and warranty paperwork.
2. Prepare a detailed report for the installation and Start-up /
Testing / Commissioning results.
3. Prepare testing, adjusting, and balancing (TAB) reports on all newly installed equipment. The Contractor shall provide full documentation of the TAB procedure and results in the form of an electronic (pdf format) report, submitted to the project COR.
4. Prepare documentation indicating that the Contractor has
provided formal training to Post facilities personnel, as selected by the FM, on the proper operation and maintenance of all equipment being provided as a part of this project. Training must be conducted by manufacturer’s representative[s] or by qualified, manufacturer certified personnel. This training shall be formalized and documented in the form of an electronic (pdf
EXHIBIT A SOW – VRV/F System
UNCLASSIFIED
Page 13 of 13 SOW – HVAC UPGRADES
format) report, submitted to the project COR.
5. The Contractor shall provide all spare parts required by the project specifications and all spare parts recommended by the equipment manufacturer. These shall be delivered to the office of the Facility Manager (FM) at the completion of project work.
(4) Clean up the working areas upon job completion as existing. For both interior and
exterior patching works, painting to match the existing color and other miscellaneous works to be done be done by the contractor before final cleaning.
Exhibit B – Project Orientation Photos and Existing Conditions
Exhibit D – BOQ
Exhibit E Proposed BOD Equipment Data Sheets
PAGE SOUTHERLAND PAGE Bill of Quantities - MECHANICAL1615 M STREET NW, WASH. DC, 20036 USAID OFFICE RENOVATION - KINSHASA, DRCPhone Fax Date:Email
NO. ITEM NAME 2 DESCRIPTION MANUFACTURER (BASIS OF DESIGN) 1 QUANTITY UNITDemo Existing Demo/Remove Existing AC Units and Turn Over to Facilities NADemo Existing Demo existing AHU Units NASubmittal Design Development FCUOutdoor Condensing Unit 3 New unit, sized for ~ 40 tons, to be located on roof LG Multi V, ARUM480BTE5 2 EA
Indoor UnitsSelection of Cassette, ducted units, Wall and Floor mounted LG ARNU053TRD4, ARNU123L2G4,
ARNU123SJA4 78 EAERV Unit 3 Energy Recovery Ventilator (600 CFM) LG 3 EA
Air Handling Unit 3Self Contained Air Handling Unit (620 CFM; VFD, DX Cooling); located on 1st Floor LG 1 EA
Air Handling Unit 3Self Contained Air Handling Unit (1340 CFM; VFD, DX Cooling); located on 2nd Floor to serve the Safe Haven Space LG 1 EA
Bathroom Exhaust Fan Updated bathroom exhaust fan to limit (150 CFM) Midea 6 EAHVAC Ducts Modify and New ductwork for ERV and AHU Sourced locally 1 LSHVAC Duct Insulation For new ductwork Sourced locally TBDAir Duct Accessories Diffusers Sourced locally TBD EAAir Outlets and Inlets Registers Sourced locally TBD EAAir Outlets and Inlets Grilles Sourced locally TBDAir Outlets and Inlets Intake Louvers Sourced locally TBD EARefrigerant Piping New piping for IDU Sourced locally TBD LMControls Standalone equipment controls LG TBD
Misc Patch, Paint, Seal Patch, Paint, Fire stop, Caulk and Sealing
Option:Existing Indoor Units Use existing compatible indoor units - Credit Existing LG Split Units EA
1 Manufacturers shall be evaluated to ensure they can be locally procured or easily obtainable regionally, within a week or less time frame and service can be found locally2 Equipment provided for budgetary pricing only; equipment shall not be used for final design3 Refer to HVAC Assesment for Proposed One-Line DiagramRefer to HVAC Assesment for Proposed One-Line Diagram
SUBTOTAL:
Standard Features:
For continual product development, LG reserves the right to change specifications without notice.© LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG Life’s Good” is a registered trademark of LG Corp. /www.lghvac.com
Notes:1. Power wiring cable size must comply with the applicable local and national codes.
Cables terminate at each frame.2. For main pipe segment size, refer to the LATS Multi V tree diagram.3. The combination ratio must be between 50‐130%.4. Sound pressure levels are tested in an anechoic chamber under ISO Standard 3745
for the combination of outdoor units.5. Communication cable between ODU and IDUs must be 2‐conductor, 18 AWG,
twisted, stranded, and shielded. Ensure the communication cable shield is properly grounded to the Master ODU chassis only. Do not ground the communication cableat any other point. Wiring must comply with all applicable local and national codes.
6. Acceptable operating voltage:7. The order of these units on the submittal (i.e., a+b+c) does not represent the
installation order. Highest capacity unit is used as the Master, followed by the nextsmaller size as Slave 1, and so on.
8. Low ambient performance with LGRED° heat technology is included in Multi V 5 units produced after February 2019.
Optional Accessories:
For: File ResubmitApproval Other
Performance: Cooling Mode:
Nominal Capacity (Btu/h)Power Input1 (kW)
Hea�����
Nominal Capacity (Btu/h)Power Input1 (kW)
Page 1 of 2
Cooling (°F DB)** Hea������Synchronous Cooling Based (°F DB) Hea�����d (°F WB)
Operating Range:
R410AEEV
2 x 18Black Coated Fin™
Unit Data:
Required Accessories:
FrameRefrigerant Charge (lbs.)Liquid (in., O.D.)High Pressure Vapor (Heat Recov only; in, O.D.)Low Pressure Vapor (in., O.D.)
Piping:²
• Advanced Smart Load Control• Intelligent Hea��• HiPOR (High Pressure Oil Return)• Smart Oil Control• Night Quiet Opera��• Fault Det����������
• Active Refrigerant Control• Variable Heat Path Exchanger• Subcooling and Vapor Injection
Control• Liquid Cooled Inverter Controller• Advanced Comfort Cooling
5 ‐ 122
ARCNB31 (Frame Connector Y‐branch, 3 pipe heat recovery) ARCNN31 (Frame Connector Y‐branch, 2 pipe heat recovery)
Electrical:FramePower Supply (V/Hz/Ø)1 MOP (A)MCA (A)Rated Amps (A) Compressor A (A) Compressor B (B) Fan (A)
Refrigerant TypeRefrigerant ControlMax. Number of Indoor Units³ Sound Pressure⁴ dB(A)Weight Frame Net (lbs.) Shipping (lbs.)Communica����e (No x AWG)⁵ Heat Exchanger Coa��
Type Quan��Oil / Type
HSS DC Scroll
PVE / FVC68D
Compressor:
Tag No.:Job Name/Location:
Date:
PO No.:
Architect: GC:
Engr: Mech:
Rep:(Company) (Project Manager)
Rated c�����������������andard 1230. Ra����e subject to chang�����������en������ra����e available at www.ahridirectory.org.
Air Guide ‐ ZAGDKA52A (3 required)Hail Guard Kit ‐ ZHGDKA52A (3 required)Low Ambient Baffle Kit ‐ ZLABKA52A (3), Control Kit ‐ PRVC2 (1 per system) Base Pan Heater - ZPLT1A52A
‐22 ‐ 61
14 ‐ 81 14 ‐ 61
Type Quan���������� Motor DriveAir Flow Rate (a) + (b) + (c) (CFM)
Propeller
Brushless Digitally Controlled Direct
Fan:
**Cooling range with the Low Ambient Baffle Kit (sold separately) is -9.9°F to ++122°F and is achieved only when all indoor units are operating in coolingmode. Does not impact heat recovery system synchronous operating range.
476,700
6
7/8 Braze
8.0
54.2
23.2
1-1/8 Braze
3/4 Braze
534666
60.3
ARUM480BTE5
8.0
67
8.0 5
6437.49
1-1/8 Braze
70
21.9
66651.146.1
1-1/8 Braze
26.3
540,000
40
26.5
(a) ARUM121BTE5
(a) ARUM121BTE5 (a) ARUM121BTE5
(a) ARUM121BTE5
30.9
SB_MultiV_5_ODU_ARUM480BTE5_2019_01_10_085642
(b) ARUM144BTE5
(b) ARUM144BTE5 (b) ARUM144BTE5
(b) ARUM144BTE5
187V - 253V
18.3
1/2 Braze
40 Ton Triple Frame Heat Pump and Heat Recovery
33,900
5/8 Braze
208-230/60/3
37.5
208-230/60/3 639
18.3-
Multi V™ 5 with LGRED° 208-230V ODU
24.3
208-230/60/380
507
1-1/8 Braze
32.39
694
(c) ARUM216BTE5
(c) ARUM216BTE5 (c) ARUM216BTE5
(c) ARUM216BTE5
1/2 Braze
19.8
For continual product development, LG reserves the right to change specifications without notice.© LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG Life’s Good” is a registered trademark of LG Corp. /www.lghvac.com Page 2 of 2
Job Name/Loca���Tag No.:
Date:
PO No.:
M5
M8M7M6
M9M10M11M12M13M14M15
11 – 15/16”11 – 1/16”10 – 1/2”8 – 7/16”8 – 1/8”6 – 1/16”
4 – 15/16”7 – 1/2”
4 – 13/16”4 – 5/16”
3”
L9
L107/8” Diameter Leak Test Hole
Left Side ViewL9
L10
L11
L12
L13L14
6 – 1/2”
5 – 9/16”
L11
L12
8 – 5/8
6 – 7/16
9 – 15/16”
L13
L14
3 – 5/8”
Right Side View
Two (2) 7/8” Diameter Wire Routing Holes (Bottom)
M5M6M7
M8M9
M10M11
M12
M13
M15
M14
M16
Power Cord Routing Hole (Bottom); two (2) - ø2”
Holes (Bottom); two - ø2-5/8,” ø2-1/8”
M163 – 5/8”
PipingRouting
Center of Gravity
19/32” Dameter Hole
Airflow
Airflow
Top View Bottom Mounting Holes
Airflow
D
W
Airflow
1 (min) 1 (min)
W W W
D
D
W
H
Typical Triple Frame Configuration
Note: Please refer to multi-frame placement information and piping rules in the Multi V 5 EngineeringManual and the Multi V 5 Installation Manual. Minimum spacing between frames is 1 inch.
146-7/16 (min)
ARUM480BTE5 (a) ARUM121BTE5
SB_MultiV_5_ODU_ARUM480BTE5_2019_01_10_085642
(b) ARUM144BTE5
40 Ton Triple Frame Heat Pump and Heat Recovery
Multi V™ 5 with LGRED° 208-230V ODU(c) ARUM216BTE5
Job Name/Location:
Date:
PO No.:
Architect: GC:
Engr: Mech:
Rep:(Company) (Project Manager)
For: File Resubmit Approval Other
Tag No.:
For a complete list of available accessories, contact your LG representative.For continual product development, LG reserves the right to change specifications without notice.© LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG Life’s Good” is a registered trademark of LG Corp. /www.lghvac.com
Notes:1. See Engineering Manual for sensible and latent c�����2. The Power Input is rated at high speed.3. Ma�������������������om of unit.4. Sound Pressure levels are tested in an anechoic chamber under ISO Standard 3745.5. Communica�� cable between Master outdoor units to indoor units / heat recovery units to be 18 AWG, 2-conductor, twisted, stranded, shielded. Ensure the communica���able shield is properly grounded to the Master outdoor unit chassis only. Do not ground the outdoor unit to indoor units / heat recovery units communica���able at any other point. Wiring must comply with all applicable local and na����odes.6. Powe��������ld provided, and must comply with the applicable local and na����odes.7. This unit comes with a dry nitrogen charge.8. All c������e net with a combina���a���tween 95 – 105%.9. Must follow installa������������ applicable LG installa�� manual.
Performance:
Cooling Capacity (Btu/h)1
Hea��������tu/h)1
Power Input2
Rated c�����������������andard 1230. Ra����e subject to chang�����������ent ������a����e available at www.ahridirectory.org.
Electrical:Power Supply (V/Hz/Ø) Rated Amps
208-230/60/1
Piping:Refrigerant Liquid Line (in., O.D.) Vapor Line (in., O.D.)Condensate Condensate Line (in., I.D.) Factory Installed Pump3
1Yes
Controls Features:
Optional Accessories:
Fan:TypeQuan��Motor/DriveMotor Quan��Air Flow Rate H/M/L (CFM)
Turbo1
Brushless Digitally Controlled/Direct1
Page 1 of 2
• Auto changeover (Heat Recovery only)• Auto opera��• Auto restart• Dual thermistor control• Dual setpoint control• Timer (on/� )• Weekly schedule
• Auto dir����swing (up/down)• Swirl wind (alternat-ing vanes)• Fan speed control• Jet cool (fast cooling)• Filter life display����������y heater applica��
• Child lock• Group control• High ceiling• Hot start• Self diagnos��• External on/��control• Wi-Fi compa���• Auto fan• Leak det���
Required Accessories:
Wireless Remote Controller - PQWRHQ0FDB�������C1 Controller - PREMTBVC0�������C1+ Controller - PREMTBVC1Simple Remote Controller - PREMTC00UPremium Remote Controller - PREMTA000Remote Temperatur���on Sensor - ZRTBS01Simple Dry Contact (1 contact, 24 VAC external power) - PDRYCB100Dry Contact for Third Party Thermostat - PDRYCB300Dry Contact for Economizer - PDRYCB400Ven������- PTVK430Casse�e Decora�e Cover - PTDCQPlasma Filter Kit - PTPKQ0Auxiliary Heater Kit - PRARH1Wi-Fi Module - PWFMDD200
Unit Data:Refrigerant TypeRefrigerant ControlSound Pressure dB(A) (H/M/L)4
Primary Filter TypeSecondary Filter Type5
Unit Net Weight (lbs.) Unit Shipping Weight (lbs.)Grille Net Weight (lbs.)Grille Shipping Weight (lbs.)
R410AEEV
WashablePlasma
Entering Mixed Air:Cooling Maximum1 (°F WB)Hea����������
7659
Grille Kit (27-9/16" x 27-9/16") - PT-UQC, or Grille Kit (24-7/16" x 24-7/16") - PT-QCHW0
5,500
Multi V™ Four‐Way 2' x 2' Ceiling Cassette
1/2 Flare 11
30
29
6,100
29 / 27 / 26
1/4 Flare
SB_MV_FourWayCassette2x2_ARNU053TRD4_2018_08_01_150438
7
265 / 247 / 212
ARNU053TRD4
5,500 Btu/h Indoor Unit
34
0.20
Job Name/Location:Tag No.:
Date:
PO No.:
For continual product development, LG reserves the right to change specifications without notice.© LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG Life’s Good” is a registered trademark of LG Corp. /www.lghvac.com Page 2 of 2
Multi V™ Four‐Way 2' x 2' Ceiling Cassette
SB_MV_FourWayCassette2x2_ARNU053TRD4_2018_08_01_150438
ARNU053TRD4
5,500 Btu/h Indoor Unit
Date:
Job Name/Location:
PO No.:
Architect:Engr:
GC:
Rep:
For: File
Approval
Mech:
Resubmit
Other
(Company) (Project Manager)
Tag #:
ARNU123L2G4Multi V™ Ducted (Low Static)
Btu/h Indoor UnitPerformance:
Cooling Nominal Test Conditions: Heating Nominal Test Conditions:Indoor: 80°F DB/67°F WBOutdoor:
95°F DBIndoor: 70°F DBOutdoor:
47°F DB/43°F WB
Heating Capacity (Btu/h) 13,600
Electrical:
Power Supply (V/Hz/Ø) 208‐230/60/1
Piping:
Refrigerant:
Condensate:
Controls Features: •Auto changeover
(Heat Recovery only) •Auto opera. on •Auto restart •Child lock •Dual thermistor control •Hot start •External on/off control
•Self diagnos cs •Timer (on/off) •Weekly schedule •Fan speed control
•Dual setpoint control •Mul ple aux heater applica ons
•Filter life and power consumption display
Unit Data:
Refrigerant Type R410A
Refrigerant Control EEV
Fan:
Type Sirocco
Fan Quantity 3
Motor/Drive Brushless Digitally Controlled/Direct
Notes:
Power Input¹ (W) 85
High Mode Airflow Rate H/M/L (CFM) 360/310/250
Entering Mixed Air:
Heating Min (°F DB) 59
Total Cooling Capacity (Btu/h) 12,300 Cooling Max⁴ (°F WB) 76
Sound Pressure⁵ dB(A) (H/M/L) 31 / 29 / 26
1.The Power Input is rated at high speed. 2.Maximum li is 27 inches from bo om of unit. Check valve not included (field
supplied). 3.Requires an LG Programmable Thermostat, Simple Controller with Mode or a
Simple Controller without Mode. 4.See Engineering Manual for sensible and latent capaci es. 5.Sound Pressure levels are tested in an anechoic chamber under ISO Standard
3745. 6.At factory fan speed se ng.
12,300
High Mode External Static Pressure (ESP)⁶ (in wg) 0.1
Page 1 of 2SB_MultiV_LowStatic__ARNU123L2G4_8_16For continual product development, LG reserves the right to change specifications without notice.LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG Life’s Good” is a registered trademark of LG Corp. /www.lghvac.com
Optional Accessories:Wireless Remote Controller ‐ PQWRHQ0FDBLG Programmable Controller ‐ PREMTB10U
Simple Controller with Mode (Black) ‐ PQRCVCL0Q
Simple Controller without Mode (Black) PQRCHCA0Q
Wall Mounted Temperature Sensor ‐ PQRSTA0
Simple Controller with Mode (White) ‐ PQRCVCL0QW
Simple Controller without Mode (White) ‐ PQRCHCA0QW
Condensate Pump Drain² (in, ID) 1
Rated Amps (A) 0.76
Liquid Line (in, OD) 1/4 FlareVapor Line (in, OD) 1/2 Flare
Net Unit Weight (lbs) 51
Shipping Weight (lbs) 61
Filter Type WashableFilter Quantity 1
Filter Dimensions 29‐5/8"x 6‐5/8"x 1/4"
Motor Quantity 2
Minimum ESP⁷ 0
Maximum ESP⁷ 0.19
7.Maximum static pressure may result in reduced airflow (CFM). 8.All communica on cable to be minimum 18 AWG, 2‐conductor, stranded,
shielded and must comply with applicable local and national code. 9.Power wiring cable size must comply with the applicable local and na onal code. 10.This unit comes with a dry nitrogen charge. 11.This data is rated 0 above sea level, with 25 of refrigerant line per indoor
unit and a 0 ft level difference between outdoor and indoor units. All capacities are net with a combination ratio between 95 – 105%.
12.Must follow installa on instruc ons in the applicable LG installa on manual.
Simple Dry Contact (1 contact, 24 VAC external power) ‐ PDRYCB100Dry Contact for Economizer ‐ PQDSBC1Dry Contact for Third Party Thermostat ‐ PDRYCB300
Standard Mode Airflow Rate H/M/L (CFM) 360/310/250
Standard Mode External Static Pressure⁶ (in wg) 0
LG Premium Controller ‐ PREMTA000
Remote Temperature Button Sensor ‐ ZRTBS01Auxiliary Heater kit ‐ PRARH1
ARNU123L2G4Multi V™ Ducted (Low Static)
Btu/h Indoor Unit
Job Name/Location:
Tag #:
Date:PO No.:12,300
Page 2 of 2SB_MultiV_LowStatic__ARNU123L2G4_8_16For continual product development, LG reserves the right to change specifications without notice.LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG Life’s Good” is a registered trademark of LG Corp. /www.lghvac.com
Job Name/Loca���
Date:
PO No.:
Architect: GC:
Engr: Mech:
Rep:(Company) (Project Manager)
For: File ResubmitApproval Other
Tag #:
For a complete list of available accessories, contact your LG representa�e.For con�����oduct development, LG reserves the right to chang�����a�����������© LG Electronics U.S.A., Inc., Englew����s, NJ. All rights reserved. “LG Life’s Good” is a registered trademark of LG Corp. /www.lghvac.com
Notes:1. See Engineering manual for sensible and latent c����s.2. The Power Input is rated at high speed.3. Sound Pressure levels are tested in an anechoic chamber under ISO Standard 3745.4. Communica�� cable between Master outdoor units to indoor units/ heat recovery units to be 18 AWG, 2-conductor, twisted, stranded,shielded. Ensure the communica���able shield is properly groundedto the Master outdoor unit chassis only. Do not ground the outdoor unitto indoor units / heat recovery units communica���able at any otherpoint. Wiring must comply with all applicable local and na����odes.5. Powe��������ld provided and must comply with the applicable local and na����odes.6. This unit comes with a dry nitrogen charge.7. All c������e net with a combina���a���tween 95 – 105%.8. Must follow installa������������ applicable LG Installa��manual.
Performance:
Cooling Capacity (Btu/h)1
Hea��������tu/h)1
Cooling Power Input2
Hea���ower Input2
Rated capacity is certified under AHRI Standard 1230. Ratings are subject to change without notice. Current certified ratings are available at www.ahridirectory.org.
Electrical:Power Supply (V/Hz/Ø) Rated Amps
208-230/60/1
Piping:Refrigerant Liquid Line (in., O.D.) Vapor Line (in., O.D.)Condensate Condensate Line (in., I.D.) Factory Installed Pump
5/8No
Controls Features:
Optional Accessories:
Unit Data:Refrigerant TypeRefrigerant ControlSound Pressure dB(A) (H/M/L)3
Primary Filter TypeUnit Net Weight (lbs.) Unit Shipping Weight (lbs.)
R410AEEV
Washable
Fan:TypeQuan��Motor/DriveMotor Quan��Air Flow Rate H/M/L (CFM)
Cross Flow1
Brushless Digitally Controlled/Direct1
Page 1 of 2
• Auto changeover(Heat Recovery only)• Auto opera��• Auto restart• Dual thermistorcontrol• Dual setpointcontrol• ���������yheater applica��
• Timer (on/� )• Weekly schedule• Auto dir����swing (up/down)• Fan speed control• Jet cool (fastcooling)• Filter life display• Child lock• Group control
• High ceiling• Hot start• Self diagnos��• External on/�control• Wi-Fi• Auto Fan• Leak Det���
Wireless Remote Controller - PQWRHQ0FDB�������C1 Controller - PREMTBVC0�������C1+ Controller - PREMTBVC1Simple Remote Controller - PREMTC00UPremium Remote Controller - PREMTA000Programmable Remote Controller - PREMTB10URemote Temperatur���on Sensor - ZRTBS01Wall Mounted Temperature Sensor - PQRSTA0Simple Dry Contact (1 contact, 24 VAC external power) - PDRYCB100Dry Contact for Third Party Thermostat - PDRYCB300Dry Contact for Economizer - PDRYCB400Auxillary Heater Kit - PRARS1
Multi V™ Standard Wall Mounted Unit
1/2 Flare
18.5
13,60012,300
37 / 34 / 30
1/4 Flare
SB_MultiV_Standard_Wall_Mounted_ARNU123SJA4_2018_04_19_143854
300 / 254 /240
ARNU123SJA4
12,300 Btu/h Indoor Unit
24.9
3030
0.25
Job Name/Loca���Tag No.:
Date:
PO No.:
For con�����oduct development, LG reserves the right to chang�����a�����������© LG Electronics U.S.A., Inc., Englew����s, NJ. All rights reserved. “LG Life’s Good” is a registered trademark of LG Corp. /www.lghvac.com
Page 2 of 2
Multi V™ Standard Wall Mounted Unit
SB_MultiV_Standard_Wall_Mounted_ARNU123SJA4_2018_04_19_143854
ARNU123SJA4
12,300 Btu/h Indoor Unit
Date:
Job Name/Location:
PO No.:
Architect:Engr:
GC:
Rep:
For: File
Approval
Mech:
Resubmit
Other
(Company) (Project Manager)
Tag #:
ARNU123CEA4Multi V™ Floor Standing (with case)
Btu/h Indoor UnitPerformance:
Cooling Nominal Test Conditions: Heating Nominal Test Conditions:Indoor: 80°F DB/67°F WBOutdoor:
95°F DBIndoor: 70°F DBOutdoor:
47°F DB/43°F WB
Heating Capacity (Btu/h) 13,600
Electrical:
Power Supply (V/Hz/Ø) 208‐230/60/1
Rated Amps (A) 0.76
Piping:
Refrigerant:
Condensate:
Controls Features: •Auto changeover
(Heat Recovery only) •Auto opera. on •Auto restart •Child lock •Dual thermistor control •Group control •E.S.P. control
•Hot start •Self diagnos cs •Timer (on/off) •Weekly schedule •Fan speed control
•Dual setpoint control•Multiple aux heater applications•Filter life and power consumption display
Unit Data:
Refrigerant Type R410A
Refrigerant Control EEV
Fan:
Type SiroccoFan Quantity 3
Motor/Drive Brushless Digitally Controlled/Direct
Notes:
Power Input² (W) 85
Airflow Rate H/M/L (CFM) 371/335/300
Total Cooling Capacity¹ (Btu/h) 12,300
Filter Type Washable
1.See Engineering Manual for sensible and latent capaci es. 2.The Power Input is rated at high speed. 3.Requires an LG Programmable Thermostat, Simple Controller with Mode or a Simple Controller
without Mode. 4.Sound Pressure levels are tested in an anechoic chamber under ISO Standard 3745. 5.All communica on cable to be minimum 18 AWG, 2‐conductor, stranded, shielded and must
comply with applicable local and national code. 6.Power wiring cable size must comply with the applicable local and na onal code. 7.This unit comes with a dry nitrogen charge. 8.This data is rated 0 above sea level, with 25 of refrigerant line per indoor unit and a 0
level difference between outdoor and indoor units. All capacities are net with a combination ratio between 95 – 105%.
9.Must follow installa on instruc ons in the applicable LG installa on manual.
12,300
Optional Accessories:
Gravity Condensate Drain (in, OD) 1Factory Installed Pump No
Sound Pressure⁴ dB(A) (H/M/L) 37/35/33
Net Unit Weight (lbs) 60
Shipping Weight (lbs) 68
Liquid Line (in, OD) 1/4 Flare
Vapor Line (in, OD) 1/2 Flare
Page 1 of 2SB‐MultiVIV_FloorStand‐ARNU123CEA4‐01‐15For continual product development, LG reserves the right to change specifications without notice.LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG Life’s Good” is a registered trademark of LG Corp. /www.lghvac.com
Wireless Remote Controller ‐ PQWRHQ0FDBLG Programmable Controller ‐ PREMTB10U
Simple Controller with Mode (Black) ‐ PQRCVCL0Q
Simple Controller without Mode (Black) PQRCHCA0Q
Wall Mounted Temperature Sensor ‐ PQRSTA0
Simple Controller with Mode (White) ‐ PQRCVCL0QW
Simple Controller without Mode (White) ‐ PQRCHCA0QW
Filter Quantity 2
Filter Dimensions 13‐3/8"x7‐1/4"x3/4"
Motor Quantity 2
Simple Dry Contact (1 contact, 24 VAC external power) ‐ PQDSB1
Dry Contact for Economizer ‐ PQDSBC1
Dry Contact for Third Party Thermostat ‐ PQDSBNGCM1
LG Premium Controller ‐ PREMTA000
ARNU123CEA4Multi V™ Floor Standing (with case)
Btu/h Indoor Unit
Job Name/Location:
Tag #:
Date:PO No.:12,300
Page 2 of 2SB‐MultiVIV_FloorStand‐ARNU123CEA4‐01‐15For continual product development, LG reserves the right to change specifications without notice.LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG Life’s Good” is a registered trademark of LG Corp. /www.lghvac.com
