RF-RXS-B SonNet Wireless Receiver BACnet IP - … · BACnet Interoperability Building Blocks...

Tel: +44 (0)1732 861200 - E-mail: [email protected] - Web: www.sontay.com

© 2017 Sontay Limited. All rights reserved

of 26

RF-RXS-B

SonNet Wireless Receiver BACnet IP Issue Number: 7.0

Date of Issue: 13/03/2017

Four Elms Road Edenbridge

Kent TN8 6AB UK

Features & Benefits

Sensing and controlling without the need of structural cabling

Minimal downtime and costs for installation

Seamless integration into BACnet IP over Ethernet

DIN-rail mounted

Easy to install and commission

Technical Overview

The RF-RXS-B SonNet Wireless receiver allows quick and seamless integration of SonNet devices into building management systems. It automatically

maps data from SonNet end devices into BACnet objects which are transmitted via the vendor independent BACnet IP communication protocol,

using a simple web browser interface. Depending on the layout of the SonNet network it can connect up to 40 nodes. Please see the System User

manual for more information.

The receiver collects data from all other devices on the wireless network, including measurements from sensors, link quality, battery levels for all

battery powered devices, hours run for all devices and the current status of all devices.

Specification

Radio Output 2.4 GHz, 16 channels automatically

selected

Direct-sequence spread spectrum

Compliance IEEE802.15.4-2006

Aerial Characteristics Gain 3.0dBi

VSWR <2:1

Data encryption AES 128

Power supply 24Vdc ±15%

24Vac ±15%, 50/60Hz

Communication: USB 2.0

RJ45 Ethernet (for BACnet IP protocol)

configured with Auto-MDI-X for 10/100

Mb/s

BIBBs supported:

DS-RP-B

DS-WP-B

DM-DDB-B

DM-DOB-B

DM-DCC-B

DS-RPM-B

DM-RD-B

Environmental:

Operating Temp. -10 to +50˚C

Operating RH 0-90%, non-condensing

Storage Temp -10 to +80˚C

Storage RH 0-90%, non-condensing

Dimensions 100 x 95 x 65mm

Weight 150g

Country of origin UK

The RF-RXS-B referred to in this data sheet meet the requirements of

EU Directive 2014/30/EU

Product Codes

RF-RXS-B SonNet Wireless Receiver BACnet IP

Accessories

RF-AERIAL-PM2 Coaxial extension cable for externally mounted

aerial – 2m length

RF-AERIAL-PM5 Coaxial extension cable for externally mounted

aerial – 5m length

WEEE Directive:

At the end of the products useful life please dispose

as per the local regulations.

Do not dispose of with normal household waste.

Do not burn.



of 26

RF-RXS-B




Kent TN8 6AB UK

How it works

These receivers are used in conjunction with the Sontay RF-IOM, RF-RR and RF-RS radio sensors and IO modules.

Routers are used to route signals from battery powered nodes and other routers to the receiver module, where the signal strength

of a direct path is not sufficient for reliable communications. Note that RF-IOMs also have full router functionality.

Data is transmitted back to the receiver at configurable time intervals, or on a configurable change in measured value. Each sensor

retains these configurations if the battery becomes discharged or requires replacement.

The receiver automatically selects which of the 16 transmission channels available gives the best radio network performance, taking

into account both signal strength and interference levels from adjacent channels and equipment (such as Wi-Fi etc.)

The sensors and routers automatically find the best path back to the receiver, which may be directly to the receiver or via “parent”

routers or RF-IOM modules.

NB The receiver can support a maximum of 16 directly connected “children”, a maximum of 12 of which can be battery powered

“end devices”. Each router or RF-IOM module can support a maximum of 16 directly connected “children”, a maximum of 8 of

which can be battery powered “end devices”. Consideration should be given on network planning for redundancy in case of router

failure or damage. A maximum of 40 devices (excl. the receiver) can be mapped into BACnet IP.

Installation

1. Remove all packaging from the network receiver and note the MAC address printed on the affixed label.

2. Mount the network receiver in the required position (this will have been determined by the site survey tool, (see the quick

start guide and manual for further details), taking care not to site the receiver, and more importantly the aerial, behind

any obstruction likely to impede the radio signal.

3. Fix the receiver to the DIN rail.

NB If the receiver is to be mounted in a metal enclosure, it is essential that the aerial is mounted externally. A 2 or 5m

coaxial extension cable assembly is available for this option.

4. Ensure the antenna is positioned in a vertical alignment.

5. Observe correct polarity if using a 24Vdc power supply.

6. Commissioning of the SonNet wireless network is accomplished using CMS (Configuration and Monitoring Software).

7. Mapping of all BACnet devices and points is accomplished via the receiver’s built-in web browser interface. The default IP

address is 192.168.1.227.

Note

If the USB port is connected (for commissioning with CMS), the Ethernet port is disabled. Ensure the USB port is disconnected

before attempting to communicate via the Ethernet port.

A full user guide is supplied with each new network receiver and is also available at www.sontay.com



of 26

RF-RXS-B




Kent TN8 6AB UK

Electrical connections

Note: The Ethernet is configured to use Auto-MDI-X for 10/100 Mb/s. It should be able to connect to any 10/100 10base-T device,

either through a switch or directly to the device without the need for a crossover cable. The Ethernet standard specifies that the

maximum 10base-T cable distance is 100 meters.

Default home screen for the RF-RXS-B

RF-RXS-B®

So

nN

et

Sta

tus

Data

Reset

0V 24V

Sta

tus

BA

Cn

et

Devic

eR

ein

itia

lize

Aerial LED indication

Power supply

LED indication Button

Button USB Connector RJ45 Ethernet

LED indication

- SonNet Status: ON if there is at least one

child node connected on the wireless

network, flashes once per second if there are

no child nodes present.

- Data: Blinking up each time data on the

wireless network is received or sent.

- BACnet Status: Blinking each time data on the

BACnet network is received or sent.

Push buttons

- Reinitialize Device: Resets the Ethernet IP

address to the factory default of 192.168.1.227.

Note it does not affect the Ethernet MAC

address or the device BACnet instance

- Reset: Resets the wireless network at the

receiver. For a short time, until nodes re-join

the network, LED D100 will flash once per

second.



of 26

RF-RXS-B




Kent TN8 6AB UK

Changing IP settings

1. From the Home page, click on the BACnet/IP Settings link

2. Change the IP address, the IP subnet mask and the IP gateway, if required. Click the appropriate “Update” button.

3. Change the Device Instance if required. Note that the last 3 digits of the device instance form the BACnet device address

(005 in the example above). Click the appropriate “Update” button.

4. Change the Device Location if required. Click the appropriate “Update” button.

5. Change the BACnet/IP UDP port number if required. Click the appropriate “Update” button.

6. Note – changing the settings values may require the RF-RXS-B to be rebooted.

Mapping SonNet Points to BACnet Objects:

1. From the Home page, click on the BACnet/IP Settings link

A list of SonNet devices, including the receiver, will appear. Note that only the last 8 characters of the SonNet device

MAC addresses are displayed.

2. Click the “Map Device” button to add the BACnet points for each required SonNet device.



of 26

RF-RXS-B




Kent TN8 6AB UK

BACnet PICS

This document contains the BACnet Protocol Implementation Conformance Statement (PICS) and BACnet®

Interoperability Building Blocks (BIBBs) for the SonNet BACnet/IP Receiver as required by the American National

Standards Institute/ American Society of Heating, Refrigerating, and Air-Conditioning Engineers (ANSI/ASHRAE)

Standard 135-2012, BACnet protocol. BACnet interoperability building blocks are collections of one or more BACnet

services. This document includes a listing of the BIBBs currently supported by this device.

The SonNet BACnet/IP Receiver is a native BACnet-Application Specific Controller (B-ASC) with BACnet/IP

capabilities.

Product Description

The SonNet devices (wireless) communicate to this Receiver, where the data is received and is modeled by various

BACnet objects. The BACnet application, running on the Receiver, will automatically model the SonNet device data to

BACnet objects, and will update the Present_Value of each object with data from the SonNet.

BACnet Requirements:

BACnet Standardized Device Profile (Annex L)

BACnet Operator Workstation (B-OWS)

BACnet Building Controller (B-BC)

BACnet Advanced Application Controller (B-AAC)

X BACnet Application Specific Controller (B-ASC)

BACnet Smart Sensor (B-SS)

BACnet Smart Actuator (B-SA)

BACnet Interoperability Building Blocks (BIBBs) (Annex K)

The table below lists all the BIBBs that are required for the BACnet Application Specific Controller (B-ASC) profile. The

BIBBS that are not required for B-ASC Profile but supported in this product are also listed.

Application Services (B-ASC) BIBB

Data Sharing - Read Property - B DS-RP-B

Data Sharing - Write Property - B DS-WP-B

Device Management - Dynamic Device Binding - B DM-DDB-B

Device Management - Dynamic Object Binding - B DM-DOB-B

Device Management - Device Communication Control - B DM-DCC-B

Data Sharing - Read Property Multiple - B DS-RPM-B

Device Management - Reinitialize Device - B DM-RD-B



of 26

RF-RXS-B




Kent TN8 6AB UK

Standard Device Binding Methods Supported

The table below lists all the standard Device Binding methods supported by this device.

Send Who-Is, receive I-Am (BIBB DM-DDB-A)

X Receive Who-Is, send I-Am (BIBB DM-DDB-B)

Send Who-Has, receive I-Have (BIBB DM-DOB-A)

X Receive Who-Has, send I-Have (BIBB DM-DOB-B)

Manual configuration of recipient device's network number and MAC address

None of the above

Standard Object Types Supported

The following is a list of the standard object types, as defined by ASHRAE, that are currently supported by this

product. This section includes object type details.

Analog Input Object Type

Dynamically creatable using BACnet's CreateObject service? No

Dynamically deletable using BACnet's DeleteObject service? No

Property Identifier Writable Required Optional Property Data

Object_Identifier No X ANALOG INPUT #

Object_Name Yes X "Temperature"

Object_Type No X ANALOG INPUT

Present_Value No X Temperature in Degrees Celsius

Status_Flags No X {FALSE,FALSE,FALSE,FALSE}

Event_State No X {NORMAL}

Out_Of_Service No X FALSE

Units No X Degrees Celsius

Reliability No X no-fault-detected



Object_Name Yes X "Humidity"



of 26

RF-RXS-B




Kent TN8 6AB UK


Present_Value No X Relative Humidity in Percent




Units No X Percent Relative Humidity




Object_Name Yes X "CO2"


Present_Value No X CO2 in Parts Per Million




Units No X Parts Per Million




Object_Name Yes X "Setpoint"


Present_Value No X Setpoint in Percent




Units No X Percent




of 26

RF-RXS-B




Kent TN8 6AB UK



Object_Name Yes X "Ch.x Measurement"


Present_Value No X Measurement in Milliamperes, Volts,

Ohms, or VFC count




Units No X Milliamperes, Volts, Ohms, or no units.


Analog Value Object Type




Object_Identifier No X ANALOG VALUE #

Object_Name Yes X “RF Channel”

Object_Type No X ANALOG VALUE

Present_Value No X RF Channel number




Units No X No units




Object_Name Yes X “Runtime”




of 26

RF-RXS-B




Kent TN8 6AB UK

Present_Value No X Runtime in hours




Units No X Hours




Object_Name Yes X “Battery Runtime”


Present_Value No X Runtime in hours




Units No X Hours




Object_Name Yes X "Parent LQI"


Present_Value No X Link Quality in Percent




Units No X Percent






of 26

RF-RXS-B




Kent TN8 6AB UK

Object_Name Yes X "Sensor Measurement Interval"


Present_Value No X Interval in Seconds




Units No X Seconds




Object_Name Yes X "Temperature COV"


Present_Value No X Temperature in Degrees Celsius




Units No X Degrees Celsius




Object_Name Yes X "Humidity COV"


Present_Value No X Relative Humidity in Percent




Units No X Percent Relative Humidity




of 26

RF-RXS-B




Kent TN8 6AB UK



Object_Name Yes X "CO2 COV"


Present_Value No X CO2 in Parts Per Million




Units No X Parts Per Million




Object_Name Yes X "Setpoint COV"


Present_Value No X Setpoint in Percent




Units No X Percent




Object_Name Yes X "PIR Off Delay"


Present_Value No X Off-Delay in Seconds





of 26

RF-RXS-B




Kent TN8 6AB UK


Units No X Seconds




Object_Name Yes X "VFC Count"


Present_Value No X VFC Count




Units No X No units




Object_Name Yes X "Ch.x Output"


Present_Value Yes X 0-10 Volts




Units No X Volts




Object_Name Yes X "Measurement Interval"




of 26

RF-RXS-B




Kent TN8 6AB UK

Present_Value No X Interval in Seconds




Units No X Seconds




Object_Name Yes X "Ch.x Input COV"


Present_Value No X 0-10 Volts




Units No X Volts




Object_Name Yes X "Ch.x Upper Alarm"






Units No X Volts





of 26

RF-RXS-B




Kent TN8 6AB UK


Object_Name Yes X "Ch.x Lower Alarm"






Units No X Volts




Object_Name Yes X "Ch.x Output COV"






Units No X Volts




Object_Name Yes X "Ch.x Output Fallback


Present_Value Yes X 0-10 Volts




Units No X Volts



of 26

RF-RXS-B




Kent TN8 6AB UK


Binary Input Object Type




Object_Identifier No X BINARY INPUT #

Object_Name No X "Online Status"

Object_Type No X BINARY INPUT

Present_Value No X Active=Online, or Inactive=Offline




Polarity No X Normal Polarity




Object_Name No X "Momentary Switch"


Present_Value No X Active=Closed, or Inactive=Open










of 26

RF-RXS-B




Kent TN8 6AB UK

Object_Name No X "VFC Input"


Present_Value No X Active=Enabled, or Inactive=Disabled








Object_Name No X "PIR"


Present_Value No X Active=detection, or Inactive=no

detection








Object_Name No X "VFC Count Reset"


Present_Value Yes X Active=reset requested, or Inactive=no

reset requested







of 26

RF-RXS-B




Kent TN8 6AB UK




Object_Name No X "CO2 Auto Calibration"


Present_Value No X Active=auto calibration enabled, or

Inactive=auto calibration disabled








Object_Name No X "Ch.x Input Alarm"


Present_Value No X Active=input alarm, or Inactive=no input

alarm








Object_Name No X "Ch.x COV Status"


Present_Value No X Active=significant change, or Inactive=no

significant change



of 26

RF-RXS-B




Kent TN8 6AB UK








Object_Name No X "Ch.x COV Status"


Present_Value No X Active=significant change, or Inactive=no

significant change






Binary Value Object Type




Object_Identifier No X BINARY VALUE #

Object_Name No X "Low Battery"

Object_Type No X BINARY VALUE

Present_Value No X Active=Low Battery, or Inactive=Battery

Okay






of 26

RF-RXS-B




Kent TN8 6AB UK





Object_Name No X "Online Status"


Present_Value No X Active=Online, or Inactive=Offline








Object_Name No X "Sensor Fault"


Present_Value No X Active=Fault, or Inactive=No Fault








Object_Name No X "Temperature COV Status"


Present_Value No X Active=Significant Change, or

Inactive=No Significant Change



of 26

RF-RXS-B




Kent TN8 6AB UK








Object_Name No X "Humidity COV Status"











Object_Name No X "CO2 COV Status"












of 26

RF-RXS-B




Kent TN8 6AB UK


Object_Name No X "Setpoint COV Status"









Multi-State Input Object Type




Object_Identifier No X MULTI-STATE INPUT #

Object_Name No X "Fan Speed Switch"

Object_Type No X MULTI-STATE INPUT

Present_Value No X 1="Off", 2="Low", 3="Medium", 4="High",

5="Auto"




Number_Of_States No X 5


State_Text No X 1="Off", 2="Low", 3="Medium", 4="High",

5="Auto"

Multi-State Value Object Type




of 26

RF-RXS-B




Kent TN8 6AB UK



Object_Identifier No X MULTI-STATE VALUE #

Object_Name No X "Battery Level"

Object_Type No X MULTI-STATE VALUE

Present_Value No X 1="Poor", 2="Okay", 3="Good"






State_Text No X 1="Poor", 2="Okay", 3="Good"



Object_Name No X "Parent Link Quality"


Present_Value No X 1="Marginal", 2="Okay", 3="Good"






State_Text No X 1="Marginal", 2="Okay", 3="Good"



Object_Name No X "Ch.x Input Type"




of 26

RF-RXS-B




Kent TN8 6AB UK

Present_Value No X 1="Current", 2="Voltage", 3="Resistance",

4="VFC", 4="Error"






State_Text No X 1="Current", 2="Voltage", 3="Resistance",

4="VFC", 4="Error"

Octet-String Value Object Type




Object_Identifier No X OCTETSTRING VALUE #

Object_Name No X “MAC Address"

Object_Type No X OCTETSTRING VALUE

Present_Value No X 00158D00001194AE






Object_Identifier No X OCTETSTRING VALUE #

Object_Name No X "Parent"

Object_Type No X OCTETSTRING VALUE

Present_Value No X 00158D00010A780C





of 26

RF-RXS-B




Kent TN8 6AB UK



Device Object Type




Object_Identifier Yes X DEVICE #

Object_Name Yes X "SonNet-BACnet-Gateway"

Object_Type No X DEVICE

System_Status No X Operational

Vendor_Name No X "Sontay Limited"

Vendor_Identifier No X 662

Model_Name No X "SBIP"

Firmware_Revision No X "0.9.1"

Application_Software_

Version No X "1.1.8"

Location Yes X "Building 1"

Description Yes X "SonNet devices"

Protocol_Version No X 1

Protocol_Revision No X 12

Protocol_Services_ Supported No X stack library filled

Protocol_Object_Types_

Supported No X stack library filled

Object_List No X stack library filled

Max_APDU_Length_

Accepted No X 1476 bytes

Segmentation_Supported No X None

APDU_Timeout No X 3000ms

Number_Of_APDU_Retries No X 3



of 26

RF-RXS-B




Kent TN8 6AB UK

Device_Address_Binding No X {}

Database_Revision No X counter

Data Link Layer Options

X BACnet IP, (Annex J)

BACnet IP, (Annex J), Foreign Device

ISO 8802-3, Ethernet (Clause 7)

ANSI/ATA 878.1, 2.5 Mb. ARCNET (Clause 8)

ANSI/ATA 878.1, RS-485 ARCNET (Clause 8), baud rate(s):

MS/TP master (Clause 9), baud rate(s): 9600, 19200, 38400, 57600, 76800,

115200

MS/TP slave (Clause 9), baud rate(s):

MS/TP (Clause 9), transceiver unit load and isolation 1/4 unit load, isolated

Point-To-Point, EIA 232 (Clause 10), baud rate(s):

Point-To-Point, modem, (Clause 10), baud rate(s):

LonTalk, (Clause 11), medium:

Other:

Network Options

Router, Clause 6 - List all routing configurations (e.g. ARCNET-Ethernet, Ethernet-MS/TP, etc.):

Annex H.3, BACnet Tunnelling Router over UDP/IP

BACnet/IP Broadcast Management Device (BBMD)

BBMD supports registrations by Foreign Devices

Segmentation Capability

Window Size

Segmented requests supported

Segmented responses supported

Device Address Binding

Static device binding supported for MS/TP Slaves and other devices



of 26

RF-RXS-B




Kent TN8 6AB UK

Character Sets Supported

X ANSI X3.4 / UTF-8

IBMÔ/MicrosoftÔ DBCS

ISO 8859-1

ISO 10646 (UCS-2)

ISO 10646 (ICS-4)

JIS C 6226

Whilst every effort has been made to ensure the accuracy of this specification, Sontay cannot accept responsibility for damage, injury, loss or

expense from errors or omissions. In the interest of technical improvement, this specification may be altered without notice.

RF-RXS-B SonNet Wireless Receiver BACnet IP - … · BACnet Interoperability Building Blocks...

Documents

Transcript of RF-RXS-B SonNet Wireless Receiver BACnet IP - … · BACnet Interoperability Building Blocks...