RF-DIM Installation Instructions - Welcome to SI LITE · 1 channel output Output power: 12v

1
WARNING This product must be wired as described below. Read these instructions fully and carefully. GENERAL RF - Thank you for purchasing a quality SI-LITE product. This product has been designed, developed and tested to our strict codes & standards. This product is designed to be powered by a power supply - for 12v either SI-LITE model SP05; SP07; SP09 or SP10; for 24v either SP02 or SP04. IMPORTANT INFORMATION Installation should be carried out in accordance with IEE wiring regulations. Always disconnect the mains supply before installa- tion. Connect the driver to the mains supply ensuring that it is protected by a fused connection unit. Make sure all electrical connections are tight. Install the fitting as described below. ASSEMBLY INSTRUCTIONS Installation / Usage Instructions RF-DIM FEATURES RF - Radio Frequency Dimming Controller For control / dimming of 12v and 24v LED single colour ribbon tape IP 20 Input voltage 12-24v DC Working temperature -20 to 60 degrees 1 channel output Output power: 12v <96w; 24v <192w On/off and Mode buttons Dims LED ribbon down to approx. 5% brightness NOTE: remote control requires 1 x 12v 27a battery (not included) 1. Connect the red / positive wire from the LED strip live end to the red (+) OUTPUT terminal, and connect the black / negative wire from the LED strip live end to the black (-) OUTPUT terminal. 2. Connect a red (positive) wire to the red (+) INPUT terminal from the chosen LED driver, and a black (negative) wire to the black (-) INPUT terminal from the LED driver. Ensure all connections are secure and that a short circuit cannot occur between connecting wires. 3. Introduce the chosen power supply to the mains supply (110-240vAC) (following power supply instructions). The LED’s will illuminate. 4. Use the fob to control the light output: On/off button - press once to turn the LED strip on or off. The fob clip can be attached to a key ring / hook when not in use. The control unit memory will retain the brightness level is use when the LED strip was previously turned off. The control unit can be wall mounted. This unit is compatible with SI LITE 12v or 24v LED strip. It has been designed to control LED strip in isolation, and not in conjunction with an external lighting control system. Press to increase brightness to desired level. Press to dim brightness to desired level.

Transcript of RF-DIM Installation Instructions - Welcome to SI LITE · 1 channel output Output power: 12v

Page 1: RF-DIM Installation Instructions - Welcome to SI LITE · 1 channel output Output power: 12v

WARNINGThis product must be wired as described below. Read these instructions fully and carefully.

GENERALRF - Thank you for purchasing a quality SI-LITE product. This product has been designed, developed and tested to our strict codes & standards. This product is designed to be powered by a power supply - for 12v either SI-LITE model SP05; SP07; SP09or SP10; for 24v either SP02 or SP04.

IMPORTANT INFORMATIONInstallation should be carried out in accordance with IEE wiring regulations. Always disconnect the mains supply before installa-tion. Connect the driver to the mains supply ensuring that it is protected by a fused connection unit. Make sure all electrical connections are tight. Install the fitting as described below.

ASSEMBLY INSTRUCTIONS

Installation / Usage Instructions RF-DIM

FEATURESRF - Radio Frequency Dimming ControllerFor control / dimming of 12v and 24v LED single colour ribbon tapeIP 20Input voltage 12-24v DCWorking temperature -20 to 60 degrees1 channel outputOutput power: 12v <96w; 24v <192wOn/off and Mode buttonsDims LED ribbon down to approx. 5% brightnessNOTE: remote control requires 1 x 12v 27a battery (not included)

1. Connect the red / positive wire from the LED strip live end to the red (+) OUTPUT terminal, and connect the black / negative wire from theLED strip live end to the black (-) OUTPUT terminal.2. Connect a red (positive) wire to the red (+) INPUT terminal from the chosen LED driver, and a black (negative) wire to the black (-) INPUTterminal from the LED driver. Ensure all connections are secure and that a short circuit cannot occur between connecting wires.

3. Introduce the chosen power supply to the mains supply (110-240vAC) (following power supply instructions). The LED’s will illuminate.4. Use the fob to control the light output:On/off button - press once to turn the LED strip on or off.

The fob clip can be attached to a key ring / hook when not in use.The control unit memory will retain the brightness level is use when the LED strip was previously turned off.

The control unit can be wall mounted.

This unit is compatible with SI LITE 12v or 24v LED strip. It has been designed to control LED strip in isolation, and not in conjunction withan external lighting control system.

Press to increase brightness to desired level.Press to dim brightness to desired level.

High heat-resistant Lithium-ion Capacitor output by vehicle power supply (12V) + Lithium-ion Capacitor voltage (~6V) = 12~18V キャパシタ電圧（12V）でバックアップ Support

High heat-resistant Lithium-ion Capacitor output by vehicle power supply (12V) + Lithium-ion Capacitor voltage (~6V) = 12~18V キャパシタ電圧（12V）でバックアップ Support

B62SR12424A/B/C/D - deltaww.com · B62SR12424A/B/C/D 12V Output DC/DC ... DS_B62SR12424_12082016 E-mail: dcdc@deltaww.com P2 Output ... Unit1 Load Unit1 …

B62SR12424A/B/C/D - deltaww.com · B62SR12424A/B/C/D 12V Output DC/DC ... DS_B62SR12424_12082016 E-mail: [email protected] P2 Output ... Unit1 Load Unit1 …

Off-Grid Inverters Inverters ... 30 minute output power ÒTRUE POWERÓ 250 watts 320 watts 800 watts ... watts Battery voltage 12V DC 24V DC 12V DC 24V DC 12V DC 24V DC …

Off-Grid Inverters Inverters ... 30 minute output power ÒTRUE POWERÓ 250 watts 320 watts 800 watts ... watts Battery voltage 12V DC 24V DC 12V DC 24V DC 12V DC 24V DC …

rage series amplifiers · rem Connects to +12V switched remote from the headunit. speaker output terminals It can also use switched +12V source for external units. Connects to the

rage series amplifiers · rem Connects to +12V switched remote from the headunit. speaker output terminals It can also use switched +12V source for external units. Connects to the

Features · 2021. 3. 25. · Features 30W (IEEE802.3at) output power >93% efficient DC/DC converter 5V, 12V and 24V variants available Very low heat output Low output ripple & noise

Features · 2021. 3. 25. · Features 30W (IEEE802.3at) output power >93% efficient DC/DC converter 5V, 12V and 24V variants available Very low heat output Low output ripple & noise

Untitled-2 [suntracbatteries.com]suntracbatteries.com/suntrac.pdf · capacity 12v 20ah 12v 40ah 12v 60ah 12v b40ah 12v b60ah 12v b80ah 12v biooah 12v 80ah 12v iooah 12v 130ah 12v

Untitled-2 [suntracbatteries.com]suntracbatteries.com/suntrac.pdf · capacity 12v 20ah 12v 40ah 12v 60ah 12v b40ah 12v b60ah 12v b80ah 12v biooah 12v 80ah 12v iooah 12v 130ah 12v

DOC008 - CaltechTHESIS · INPUT ONTRO 172 Coupled Inductor 12V 4A COUBLED 80T -12V 4A Figure 11.4: a)150w three-output Cuk converter. b) The schematic of the power stage.

DOC008 - CaltechTHESIS · INPUT ONTRO 172 Coupled Inductor 12V 4A COUBLED 80T -12V 4A Figure 11.4: a)150w three-output Cuk converter. b) The schematic of the power stage.

Design reference of 3W AC-DC power supply 12V output ...

Design reference of 3W AC-DC power supply 12V output ...

UB10 - pulspower.com · 12V 24V output at 10A 12V output at 5A Output current (normal mode) ... controller along with a standard 24V power supply and one 12V battery can bridge power

UB10 - pulspower.com · 12V 24V output at 10A 12V output at 5A Output current (normal mode) ... controller along with a standard 24V power supply and one 12V battery can bridge power

Department of Mathematics | Penn Mathghrist/EAT/EATchapter1.pdfdim ker dim coker dim dim ! dim dim dim dim " # # # $ # # ! # $ % & O % ' $

Department of Mathematics | Penn Mathghrist/EAT/EATchapter1.pdfdim ker dim coker dim dim ! dim dim dim dim " # # # $ # # ! # $ % & O % ' $

INTERAKTIVITÄT COMPUTER AUDIO STROMVERSORGUNG · 2020. 10. 6. · ap7-u65 dimb dim c dim a 1000mm 39.4in dim d dim e dim f dim l 25mm1.0 dim g 658mm 25.9in dim h 1000 dim j dim k

INTERAKTIVITÄT COMPUTER AUDIO STROMVERSORGUNG · 2020. 10. 6. · ap7-u65 dimb dim c dim a 1000mm 39.4in dim d dim e dim f dim l 25mm1.0 dim g 658mm 25.9in dim h 1000 dim j dim k

Promethean - INTERACTIVITÉ INFORMATIQUE...DIM A DIM B DIM C 1000mm 39.4in DIM D 25mm1.0 DIM L DIM F DIM E DIM G 658mm 25.9in DIM H 1000mm39.4in DIM I 583 DIM J DIM K AP7-B70 DIM A

Promethean - INTERACTIVITÉ INFORMATIQUE...DIM A DIM B DIM C 1000mm 39.4in DIM D 25mm1.0 DIM L DIM F DIM E DIM G 658mm 25.9in DIM H 1000mm39.4in DIM I 583 DIM J DIM K AP7-B70 DIM A

Dim Dim List

Dim Dim List

DISPLAY ANSCHLÜSSE · 2020. 10. 20. · ap7-b70 dim a dim b dim c 1000mm 39.4in dim d 25mm1.0 dim l dim f dim e dim g 658mm 25.9in dim h 1000mm39.4in dim i 583 dim j dim k ap7-b70

DISPLAY ANSCHLÜSSE · 2020. 10. 20. · ap7-b70 dim a dim b dim c 1000mm 39.4in dim d 25mm1.0 dim l dim f dim e dim g 658mm 25.9in dim h 1000mm39.4in dim i 583 dim j dim k ap7-b70

DC/AC Power Inverter Modified Sine Wave Input 12V DC Output 220V AC … · 2019. 9. 18. · DC/AC Power Inverter Modified Sine Wave Input 12V DC Output 220V AC 3000W ModelloIRS3000-12

DC/AC Power Inverter Modified Sine Wave Input 12V DC Output 220V AC … · 2019. 9. 18. · DC/AC Power Inverter Modified Sine Wave Input 12V DC Output 220V AC 3000W ModelloIRS3000-12

GLSV-035 series - MPL Power · GLSV - 035 B xxx Series name Rated Output Power [W] Option name 012 – rated output voltage is 12V 024 – rated output voltage is 24V 036 – rated

GLSV-035 series - MPL Power · GLSV - 035 B xxx Series name Rated Output Power [W] Option name 012 – rated output voltage is 12V 024 – rated output voltage is 24V 036 – rated

16-70V 16-80V ±12V 4A 87% @ 2A / 85% @ 4A...16-70V 16-80V ±12V 4A 87% @ 2A / 85% @ 4A Continuous Input Transient Input Output Total Output Efficiency. Product# MQHL-28E-12D Phone

16-70V 16-80V ±12V 4A 87% @ 2A / 85% @ 4A...16-70V 16-80V ±12V 4A 87% @ 2A / 85% @ 4A Continuous Input Transient Input Output Total Output Efficiency. Product# MQHL-28E-12D Phone

INTERAKTYVUMAS KOMPIUTERIO PARAMETRAI GARSAS … · DIM G 25.9in DIM I DIM K AP7-U65 DIMB DIM C DIM A 1000mm 39.4in DIM D DIM F DIM L DIM E 25mm1.0 DIM H 583mm 23.0in DIM J 1000 658mm

INTERAKTYVUMAS KOMPIUTERIO PARAMETRAI GARSAS … · DIM G 25.9in DIM I DIM K AP7-U65 DIMB DIM C DIM A 1000mm 39.4in DIM D DIM F DIM L DIM E 25mm1.0 DIM H 583mm 23.0in DIM J 1000 658mm

User Manual - Kecesaudio...5V/7V + 9V/12V with USB Output. 9V/12V + 12V/15V 9V/12V + 18V/19V 9V/12V + 20V/24V Single Output 9V/12V 19V/20V P8 Dual Output Cut Off Output condition Output

User Manual - Kecesaudio...5V/7V + 9V/12V with USB Output. 9V/12V + 12V/15V 9V/12V + 18V/19V 9V/12V + 20V/24V Single Output 9V/12V 19V/20V P8 Dual Output Cut Off Output condition Output

INPUT / OUTPUT MODULES - Western Automation...2018/10/04  · IO-DIM Series Description Part No. 4 x VFC or 24V AC/DC inputs, 0-10V DC output IO-DIM-4 6 x VFC or 24V AC/DC inputs,

INPUT / OUTPUT MODULES - Western Automation...2018/10/04  · IO-DIM Series Description Part No. 4 x VFC or 24V AC/DC inputs, 0-10V DC output IO-DIM-4 6 x VFC or 24V AC/DC inputs,