REVISIONS - Littelfuse/media/commercial-vehicle/2d-prints/pdm/littelfuse-pdm-hwb...6.terminal...
5
Transcript of REVISIONS - Littelfuse/media/commercial-vehicle/2d-prints/pdm/littelfuse-pdm-hwb...6.terminal...
79.90±0.50
97.8
66.5±0.5
157.6
10.0
6.0
6.0
65.8 60.0 36.0
2X 6.4 138.0
5.8
R10.0
4X R3.20
7.8 (CL TO CL )
8.1(CL TO CL ) VENT
1
2
3
4
5
6
OUTLINE
60 WAY HWB60 AL FUSE HOLDER
NOTES:MATERIAL:1.
BASE & COVER: PA66, 30% GF, BLACK TPA: PA, BLUE SEAL: SILICONE RUBBER, GREEN2. TORQUE RATING(ON FLAT SURFACE): 6-8 Nm USING M6 BOLT & LOCK WASHER3. FUSE RATING: 30A PER CIRCUIT4. OPERATING & STORAGE TEMPERATURE: -40 C TO 105 C5. INGRESS PROTECTION (IP) RATING OF THE HWB60 AL WITH GASKET, COVER & BASE PLATE WITH VENT AT ROOM TEMPERATURE IS IP66 & IP67 (IEC60529). IP OF THE HWB60 AL ASSEMBLY AT 70 C (MODULE) TO 25 C WATER TEMPERATURE WHILE THE VENT AREA IS VENTED (BREATH) TO AIR DURING TESTING IS IP686.TERMINAL RETENTION PER USCAR 2 SECTION 5.4.1.3 USING PROPER DELPHI METRI-PACK TERMINALS (SEALED / TANGLESS) 7.TPA RETENTION PER USCAR 2 SECTION 5.4.5.28. MAXIMUM CONTINUOUS CURRENTS: 250A FOR ENTIRE FUSEHOLDER9. 60 TERMINAL OPENINGS
REVISIONSZONE REV. DESCRIPTION DATE APPROVED
A 518324GCF-NEW RELEASE WITH VENT IN BASE, REMOVE PLASTICS GRID FROM ASSEMBLY A HOANG 1/30/2018 A HOANG
FEMALE TERMINAL FOR MINI FUSE
CABLE SIZE mm² FEMALE TERMINAL (DELPHI 280 SEAL) CABLE DIAMETER
CABLE SEAL (DELPHI 280 METRI-PACK REEL/LOOSE)
COLOR
0.50 - 0.35 12084201 1.70 - 1.29 12034365 / 15324983 DARK RED
1.0 - 0.50 12077411 2.15 - 1.60 12089444 / 15324985 PURPLE
2.0 -1.0 15363933 2.85 - 2.03 12015284 / 15324982 GREEN
3.0 - 2.0 12129493 3.49 - 2.81 12015359 / 15324980 GRAY
5.0 12077413 4.30 - 3.45 12015360 / 15324981 BLUE
CAVITY PLUG 12010300 GREEN
NO. COMPONENT NO. COMPONENT NAME QTY/M U/M
1 873-018 COVER 1 EA
2 901-323 SEAL 1
3 942-002 VENT 1 EA
4 883-029 CLIP 2 EA
5 868-974 BASE WITH VENT 1 EA
6 883-083 TPA 6 EA
D
C
B
A
B
C
D
12345678
8 7 6 5 4 3 2 1
E
F
E
F
A
THIS DRAWING AND THE INFORMATION CONTAINED WITHIN IT ARE CONFIDENTIAL AND MAY NOT BE COPIED OR DISCLOSED WITHOUT THE WRITTEN PERMISSION OF LITTELFUSE.
DWG. NO.
CHECKED
-
-
-
-
-
DRAWN
A HOANG
A HOANG
SCALE 1:1
SIZEC
DATENAME
-
-
-
30 NOV 2017
30 NOV 2017
OL-PDM71006ZXMSHEET 1 OF 1
REV.A
THIRD ANGLE PROJECTION
DO NOT SCALE DRAWING
TITLE
DENOTES A CHARACTERISTIC THAT PROVIDES AN INDICATION OF PROCESS PERFORMANCE.PROCEDURE FOR MEASUREMENTAND TRACKINGTO BE DEFINEDIN LITTELFUSE INSPECTION INSTRUCTIONS
DENOTES CPK DIMENSIONS MINIMUM CPK VALUE
CP
ST
CPK
●
DENOTES CP DIMENSIONS, -MINIMUM CP VALUE MUST BE WITHIN THEDIMENSIONAL LIMITATIONS SHOWN ON DRAWING AND INITIALLY LOCATEDTO ALLOW FOR MAXIMUM TOOL LIFE
SAFETY/ COMPLIANCE CRITICAL CHARACTERISTICS SYMBOL
TOLERANCES UNLESS OTHERWISE SPECIFIED ONE PLACE DECIMAL 0.5 THREE PLACES DECIMAL 0.100TWO PLACES DECIMAL 0.20 ANGULAR 2
DIMENSIONS ARE SHOWN IN MILLIMETERS. DIMENSIONS AND TOLERANCES AREDEFINED ACCORDING TO ANSI/ASME Y14.5-1994.
FIT FUNCTION CRITICAL CHARACTERISTICS SYMBOL
<S>
79.90±0.50
97.8
66.5±0.5
157.6
10.0
6.0
6.0
65.8 60.0 36.0
2X 6.4 138.0
5.8
R10.0
4X R3.20
7.8 (CL TO CL )
8.1(CL TO CL ) VENT
1
2
3
5
6
4
OUTLINE
60 WAY HWB60 AL FUSE HOLDER
NOTES:MATERIAL:1.
BASE & COVER: PA66, 30% GF, BLACK TPA: PA, BLUE SEAL: SILICONE RUBBER, GREEN2. TORQUE RATING(ON FLAT SURFACE): 6-8 Nm USING M6 BOLT & LOCK WASHER3. FUSE RATING: 30A PER CIRCUIT4. OPERATING & STORAGE TEMPERATURE: -40 C TO 105 C5. INGRESS PROTECTION (IP) RATING OF THE HWB60 AL WITH GASKET, COVER & BASE PLATE WITH VENT AT ROOM TEMPERATURE IS IP66 & IP67 (IEC60529). IP OF THE HWB60 AL ASSEMBLY AT 70 C (MODULE) TO 25 C WATER TEMPERATURE WHILE THE VENT AREA IS VENTED (BREATH) TO AIR DURING TESTING IS IP686.TERMINAL RETENTION PER USCAR 2 SECTION 5.4.1.3 USING PROPER DELPHI METRI-PACK TERMINALS (SEALED / TANGLESS) 7.TPA RETENTION PER USCAR 2 SECTION 5.4.5.28. MAXIMUM CONTINUOUS CURRENTS: 250A FOR ENTIRE FUSEHOLDER9. 60 TERMINAL OPENINGS
REVISIONSZONE REV. DESCRIPTION DATE APPROVED
A 518324GCF-NEW RELEASE WITH VENT IN BASE, REMOVE PLASTICS GRID FROM ASSEMBLY A HOANG 2/28/2018 A HOANG
FEMALE TERMINAL FOR MINI FUSE
CABLE SIZE mm² FEMALE TERMINAL (DELPHI 280 SEAL) CABLE DIAMETER
CABLE SEAL (DELPHI 280 METRI-PACK REEL/LOOSE)
COLOR
0.50 - 0.35 12084201 1.70 - 1.29 12034365 / 15324983 DARK RED
1.0 - 0.50 12077411 2.15 - 1.60 12089444 / 15324985 PURPLE
2.0 -1.0 15363933 2.85 - 2.03 12015284 / 15324982 GREEN
3.0 - 2.0 12129493 3.49 - 2.81 12015359 / 15324980 GRAY
5.0 12077413 4.30 - 3.45 12015360 / 15324981 BLUE
CAVITY PLUG 12010300 GREEN
NO. COMPONENT NO. COMPONENT NAME QTY/M U/M
1 873-018 COVER 1 EA
2 901-323 SEAL 1 EA
3 942-002 VENT 1 EA
4 883-088 CLIP, EASY LATCH 2 EA
5 868-974 BASE WITH VENT 1 EA
6 883-083 TPA 6 EA
D
C
B
A
B
C
D
12345678
8 7 6 5 4 3 2 1
E
F
E
F
A
THIS DRAWING AND THE INFORMATION CONTAINED WITHIN IT ARE CONFIDENTIAL AND MAY NOT BE COPIED OR DISCLOSED WITHOUT THE WRITTEN PERMISSION OF LITTELFUSE.
DWG. NO.
CHECKED
-
-
-
-
-
DRAWN
A HOANG
A HOANG
SCALE 1:1
SIZEC
DATENAME
-
-
-
30 NOV 2017
30 NOV 2017
OL-PDM71008ZXMSHEET 1 OF 1
REV.A
THIRD ANGLE PROJECTION
DO NOT SCALE DRAWING
TITLE
DENOTES A CHARACTERISTIC THAT PROVIDES AN INDICATION OF PROCESS PERFORMANCE.PROCEDURE FOR MEASUREMENTAND TRACKINGTO BE DEFINEDIN LITTELFUSE INSPECTION INSTRUCTIONS
DENOTES CPK DIMENSIONS MINIMUM CPK VALUE
CP
ST
CPK
●
DENOTES CP DIMENSIONS, -MINIMUM CP VALUE MUST BE WITHIN THEDIMENSIONAL LIMITATIONS SHOWN ON DRAWING AND INITIALLY LOCATEDTO ALLOW FOR MAXIMUM TOOL LIFE
SAFETY/ COMPLIANCE CRITICAL CHARACTERISTICS SYMBOL
TOLERANCES UNLESS OTHERWISE SPECIFIED ONE PLACE DECIMAL 0.5 THREE PLACES DECIMAL 0.100TWO PLACES DECIMAL 0.20 ANGULAR 2
DIMENSIONS ARE SHOWN IN MILLIMETERS. DIMENSIONS AND TOLERANCES AREDEFINED ACCORDING TO ANSI/ASME Y14.5-1994.
FIT FUNCTION CRITICAL CHARACTERISTICS SYMBOL
<S>
79.90±0.50
97.8
66.5±0.5
157.6
10.0
6.0
6.0
65.8 60.0 36.0
2X 6.4 138.0
5.8
R10.0
4X R3.20
7.8 (CL TO CL )
8.1(CL TO CL ) VENT
1
2
3
4
5
6
7
OUTLINE
60 WAY HWB60 AL FUSE HOLDER
NOTES:MATERIAL:1.
BASE & COVER: PA66, 30% GF, BLACKTPA: PA, BLUESEAL: SILICONE RUBBER, GREEN
2. TORQUE RATING(ON FLAT SURFACE): 6-8 Nm USING M6 BOLT & LOCK WASHER3. FUSE RATING: 30A PER CIRCUIT4. OPERATING & STORAGE TEMPERATURE: -40 C TO 105 C5. INGRESS PROTECTION (IP) RATING OF THE HWB60 AL WITH GASKET, COVER & BASE PLATE WITH VENT AT
ROOM TEMPERATURE IS IP66 & IP67 (IEC60529). IP OF THE HWB60 AL ASSEMBLY AT 70 C (MODULE) TO 25 C WATER TEMPERATUREWHILE THE VENT AREA IS VENTED (BREATH) TO AIR DURING TESTING IS IP68
6.TERMINAL RETENTION PER USCAR 2 SECTION 5.4.1.3 USING PROPER DELPHI METRI-PACK TERMINALS (SEALED / TANGLESS)7.TPA RETENTION PER USCAR 2 SECTION 5.4.5.28. MAXIMUM CONTINUOUS CURRENTS: 250A FOR ENTIRE FUSEHOLDER9. 60 TERMINAL OPENINGS
REVISIONSZONE REV. DESCRIPTION DATE APPROVED
A 518324GCF-NEW RELEASE FOR PERMANENT CORRECTIVE CONTAINMENT (PCA) A HOANG 11/30/2017 A HOANG
FEMALE TERMINAL FOR MINI FUSE
CABLE SIZE mm² FEMALE TERMINAL (DELPHI 280 SEAL) CABLE DIAMETER
CABLE SEAL (DELPHI 280 METRI-PACK REEL/LOOSE)
COLOR
0.50 - 0.35 12084201 1.70 - 1.29 12034365 / 15324983 DARK RED
1.0 - 0.50 12077411 2.15 - 1.60 12089444 / 15324985 PURPLE
2.0 -1.0 15363933 2.85 - 2.03 12015284 / 15324982 GREEN
3.0 - 2.0 12129493 3.49 - 2.81 12015359 / 15324980 GRAY
5.0 12077413 4.30 - 3.45 12015360 / 15324981 BLUE
CAVITY PLUG 12010300 GREEN
NO. COMPONENT NO. COMPONENT NAME QTY/M U/M
1 873-018 COVER 1 EA
2 901-322 GRID 1 EA
3 901-323 SEAL 1 EA
4 942-002 VENT 1 EA
5 883-029 CLIP 2 EA
6 868-974 BASE WITH VENT 1 EA
7 883-083 TPA 6 EA
D
C
B
A
B
C
D
12345678
8 7 6 5 4 3 2 1
E
F
E
F
A
THIS DRAWING AND THE INFORMATION CONTAINED WITHIN IT ARE CONFIDENTIAL AND MAY NOT BE COPIED OR DISCLOSED WITHOUT THE WRITTEN PERMISSION OF LITTELFUSE.
DWG. NO.
CHECKED
-
-
-
-
-
DRAWN
A HOANG
A HOANG
SCALE 1:1
SIZEC
DATENAME
-
-
-
30 NOV 2017
30 NOV 2017
OL-PDM71009ZXMSHEET 1 OF 1
REV.B
THIRD ANGLE PROJECTION
DO NOT SCALE DRAWING
TITLE
DENOTES A CHARACTERISTIC THAT PROVIDES AN INDICATION OF PROCESS PERFORMANCE.PROCEDURE FOR MEASUREMENTAND TRACKINGTO BE DEFINEDIN LITTELFUSE INSPECTION INSTRUCTIONS
DENOTES CPK DIMENSIONS MINIMUM CPK VALUE
CP
ST
CPK
●
DENOTES CP DIMENSIONS, -MINIMUM CP VALUE MUST BE WITHIN THEDIMENSIONAL LIMITATIONS SHOWN ON DRAWING AND INITIALLY LOCATEDTO ALLOW FOR MAXIMUM TOOL LIFE
SAFETY/ COMPLIANCE CRITICAL CHARACTERISTICS SYMBOL
TOLERANCES UNLESS OTHERWISE SPECIFIED ONE PLACE DECIMAL 0.5 THREE PLACES DECIMAL 0.100TWO PLACES DECIMAL 0.20 ANGULAR 2
DIMENSIONS ARE SHOWN IN MILLIMETERS. DIMENSIONS AND TOLERANCES AREDEFINED ACCORDING TO ANSI/ASME Y14.5-1994.
FIT FUNCTION CRITICAL CHARACTERISTICS SYMBOL
<S>
