Revised: Hand Tools - KONEL

January 2010

Hand Toolsand associated equipment

Revised:

Europe, the Middle East and Africa

(Internet download)

Tyco Electronics recommends that hand powered tools are used only for repair or very low volume production use.Care must be taken not to use these types of tools continuously for prolonged periods as RSI (repetitive strain injury) may result.

Tyco Electronics provides a wide range of powered equipment options where medium to high volumes are anticipate

Terminal TypesTerminal type descriptions are very general and can be misleading if solely used to identify suitable tooling.It is strongly recommended that when searching for a tool for your application, you establish and use a specific Loose piece PN.

Tool GradeA prime consideration when choosing the appropriate tool for an application.Our hand tools are categorised into three levels; Service, Commercial and Premium, each level requiring less operator skill respectively so that the specified crimp parameters are met repeatedly.

Service tools rely heavily on operator skill to ensure that terminal and wire are correctly positioned correctly and that the specified crimp height is achieved repeated.

Commercial tools rely on some operator skill to ensure that terminal and wire are correctly positioned, but have a ratchet or certi-crimp mechanism to ensure that the specified crimp height is achieved repeated.

Premium tools have terminal and wire positioning aids built in, along with a ratchet or certi-crimp mechanism to best ensure that that all of the specified crimp parameters are met repeatedly.

Loose PieceFor a Terminal to be suitable for use in a hand tool it must be cut from the carrier strip it is manufactured on, and more importantly pre-formed.We call this the loose piece (LP) version - this may have the same / different base PN and / or dash number than the strip version.Pre-forming allows the short stroke of a hand tool to work and helps stabilise the terminal within the tool and form correctly during crimping

Wire RangeThe overall wire range is also a prime consideration when choosing the appropriate tool for an application.Often there will be several tools referenced to the same product but having different wire ranges.

Tool TypeChoosing a tool type maybe driven by several factors; simply by type preference, or by the application needs itself ie a heavy duty crimp, industry specification requirements etc.

Terminal Wire RangeEach Terminal will have a specific wire range, this may be different for different dash numbers of the same base PN.This will determine which wire / tool combinations that can be used with the terminal.

Choosing the right tool

1. Enter your Terminal PN into the search.2. Establish the wire sizes that you want to use within the terminal(s) wire range.3. Check the db for the tool options available for your PN - Nothing available? Then contact your nearest PIC.4. Choose a tool based on; tool type, wire range and tool grade that best suits your application.

What you need to know about Terminals

What you need to know about Hand Tools

Introduction

The procedures in the relevant Instruction Sheet must be followed to achieve optimum crimp results

SDE EquipmentEquipment Type PageDie-set - SDE (shoulder) 8Die-set - SDE (pin) 9SDE PRO-CRIMPER III 10SDE DA Hand Tool 10Die-set - SDE SA 11Die-set - SDE SA Plus 11SDE SA 12Die-set - SDE Premium 12SDE BATTERY TOOL Kit 13SDE Electric Terminator 13SDE 626 Pneumatic 13SDE Bench Press Adapter 14

General Hand Tool TypesEquipment Type PageCERTI-CRIMP II SAHT 15CERTI-CRIMP II SAHT - Short Handle 16CERTI-CRIMP II SAHT - Long Handle 16CERTI-CRIMP II SAHT - Head Assy (Square) 17CERTI-CRIMP II SA Battery Tool Kit 17Adapter - CERTI-CRIMP II to Electric Terminator 17Double Action Hand Tool 18Double Action Hand Tool Battery Tool Kit 19Adapter - Double Action Hand Tool to 626 Pneumatic 19C-Head SAHT 20C-Head SAHT - LD 20Die-set - C-Head SAHT 21Die-set - C-Head SAHT - HD 21C-Head SAHT Battery Tool Kit 22Adapter - C-Head SAHT to Bench Press SSC-2FP 22Adapter - C-Head SAHT to Electric Terminator 22Heavy Head Hand Tool 23Heavy Head Hand Tool Battery Tool Kit 24Adapter - Heavy Head to 626 Pneumatic 24Reel-Fed CERTI-LOK 25CERTI-LOK 25Adapter - CERTI-LOK to Electric Terminator 25PEZ 100 26ERGOCRIMP 26Tetra-Crimp Hand Tool 26Mini CERTI-LOK 27Modular Mini CERTI-LOK 27C-Frame Hand Tool 27D-Frame Tool 28Trapezium Crimp Tool 28Square Crimp Tool 29Service Tool 29TERMI-POINT Hand Tool 30Service Kit Tool 31Die-set - Service Kit Tool 31

Hand Tools for IDC ApplicationsEquipment Type PagePistol Grip 32Pistol Grip II 33Pistol Grip III 33Special Hand Tool for DUOPLUG 2.5 34Hand Tool - ANSLEY 779-2100 34

Insertion / Extraction Tool TypesEquipment Type PageStandard Extraction Tool 35Extraction Tool 36Standard Insertion Tool 37Insertion Tool 37Tee Handled Insertion Tool 38Insertion / Extraction Tool Kit 38

Heavy Duty Crimp Equipment & AccessoriesEquipment Type PageROTA-CRIMP Hand Tool 39Bantam ROTA-CRIMP Hand Tool 39Hydraulic Hand Tool - SOLISTRAND 40Hydraulic Head - SOLISTRAND 40Battery-Hydraulic Tool 100 KN 41Cable Cutter - Battery-Hydraulic Tool 100 KN 42'U' Die Assy 42'U' Die Assy (14 ton) 43'U' Die Nest 44'U' Die Indenter 45'U' Die 12 Ton Hydraulic Hand Tool 45'U' Die 14 Ton Hydraulic Hand Tool 46'U' Die 12 Ton Hydraulic Head 46Battery-Hydraulic Tool Kit - 12 Ton 'U' Die 46'U' Die 14 Ton Hydraulic Head 47'U' Die 14 Ton Hydraulic Head - Latched 47Dies for Battery Tool Kit - 4 Ton Latch Head 48Battery Tool Kit - 4 Ton Latch Head 48Die-set - Hydraulic Head Open (Shank Die) 49Hydraulic Head Open (Shank Die) 50Hydraulic Head Open - Dyna-Crimp 50Die-set - Hydraulic Head Closed (Shank Die) 51Hydraulic Head Closed (Shank Die) 51Hydraulic Head Closed - Dyna-Crimp 52Die-set - Hydraulic Head Open (Shank Die H'Duty) 52Hydraulic Head Open (Shank Die Heavy Duty) 53Hydraulic Head Open (Heavy Duty) - Dyna-Crimp 53Die-set - Hydraulic Head Closed (Shank Die H'Duty) 54Hydraulic Head Closed (Shank Die Heavy Duty) 54Hydraulic Head Closed (Heavy duty) - Dyna-Crimp 55Heavy duty Electric Hydraulic Pump 55Electric Hydraulic Pump, light duty 55Hydraulic Hand Pump 56Hydraulic Foot Pump 56Group Cutter 56Cable Cutter 350 mcm 57Cable Cutter 500 mcm 57Cable Cutter 350 mcm with Ratchet 57Cable Cutter 500 mcm with Ratchet 58Cable Cutters SH Range 58

Contractor ToolsEquipment Type PageCorex Coax Stripper 59Coax Cable Stripper 59Oden - Cable Stripper 60Cyclops - Cable Stripper 60Economy Wire Stripper & Cutter 60Tor - Rotary Cable Stripper 61Rotary Cable Stripper 61Embla - Automatic Wire Stripper 62Automatic Wire Stripper 62Die-cast Automatic Wire Stripper 63Small Wire Cutters 63KT 80 Cutting Tool 63Cable Tie Gun 64Non-impact Punch-down Tool 64Impact Punch-down Tool 64Premium Impact Punch-down Tool 65Professional Hand Tool 66Mod Jack Tool 67Crimping Kit for Modular Plugs 67Tone Generator 68Tone Tracer 684-Pair Tester 68Butt Set 69SUPER CHAMP II 69SUPER CHAMP FT 69CRIMPAC CG 70Die-set - SDE for Fibre Optic Connectors 70Fibre Cleaver - S 315 70Fibre Cleaver - Universal 71Dual Purpose Butterfly Tool 71

Tools for Screw-machined ContactsEquipment Type PageAF8 72AF8 - Turret 72AFM8 73AFM8 - Positioner 73FT8 74M300 BT 74M309 74M310 75M317 75MH860 76HX4 76ERGOCRIMP - Chrome 77Hydraulic Hand Tool 30 KN 77Hydraulic Hand Tool 60 KN 78

Industry / Product specific kitsEquipment Type PageAmpliset repair Kit 79Service Kit - SUPERCHAMP II 79Service Kit - CRIMPAC CG 80Universal Service Tool Kit 80Starter Kit 81Installers Kit 81Pistol Grip tool kit for 2mm FB + HM 82Pistol Grip Kit for RV-100 82VS-3 Hand Tool Kit 82VS-3 Hand Tool Holder 83

Telecoms and Outside PlantEquipment Type Page10 Pair Splicing Kit 8425 Pair Splicing Kit 85Crimping Pliers 85Double Point Electrical Tester 86Single Point Insertion Tool 8610 Pair Separator Tool 86Check Combe, 10 pair 87Check Combe, 25 pair 87Single Point Separator Tool 87Splicing Head, 10 Pair with Pedestal Bar, 10 Pair 88Splicing Head, 10 Pair 88Splicing Head, 25 Pair 88

Power Assist optionsEquipment Type PageBattery Tool Kit 89Electric Terminator EU 89Micro Pneumatic 90Micro Pneumatic Adapter 90Micro Pneumatic Crimping Head 91626 Pneumatic 91626 Pneumatic Adapter 92626 Pneumatic Crimping Head (Small Tool Holder) 92626 Pneumatic Crimping Head (Large Tool Holder) 93Bench Press SSC-2FP 93

SDE Equipment Revised: January 2010

Die-set - SDE (shoulder)

Features:Use in:SDE PRO-CRIMPER III Hand Tool 354940-1SDE PEW 12 Hand Tool 9-1478240-0SDE DA Hand Tool 1213745-1SDE BATTERY TOOL (Kit) 1725837-2/-5 for shoulder diesSDE 626 Head 679304-1 + accessoriesSDE Electric Terminator 1490076-2SDE Bench Press Adapter 1579000-8 + Press 1481004-7

Predominately used on closed-barrel terminals.These Dies are ideally suited to R&D prototyping, networking, commercial & industrial and all manor of maintenace applications.

Image representative of type only

Part Number Description mm² (AWG) or other58436-1 50Ω BNC & TNC - Hex Crimp RG 58, 62, 5958509-1 BUDGET SOLISTRAND 0.4 - 6.0 (22-10)58573-2 Spare Wire Cap 0.15 - 6.0 (26-10)91902-1 Coax - N Series RG 14158436-3 Coax RG 174, 188, 316, 179, 161,

1871424050-1 Coax RG 174,18858536-1 Coax RG 71 B58489-1 Coax - Hex COMMercial RG 161,174,179,187,

188,31658485-1 Coax - Hex COMMercial RG, 8,9,11,213,214,21658560-2 MODULAR PLUG connectors 10 Posn790163-6 MODULAR PLUG - 8 Posn790163-4 MODULAR PLUG - 8 Posn Shielded224928-2 MODULAR PLUG - 8 Posn, strain relief Ø4.70 - 5.76

Ins. Ø0.19-0.22mm790163-2 Modular Plug 8 Position Shielded 0.15 - 0.2 (26-24) CAT 691911-3 MULTI-MATE - Submin RG 17458424-1 Optimate ST Cable Dia 3 mm58423-1 PIDG, PLASTI-GRIP - RBY All Types including PIDG FASTON Flag 22-18 & 16-14 0.4 - 6.0 (22-10)58545-1 SOLISTRAND Terminals & Splices 0.4 - 6.0 (22-10)

Only the most popular options are listed here, please use our online search by terminal PN to find the right tool for your application, and contact us where information is unclear or missing - there may well be something available for your requirement.


Die-set - SDE (pin)

Features:Use in:SDE PRO-CRIMPER III Hand Tool 354940-1SDE PEW 12 Hand Tool 9-1478240-0SDE DA Hand Tool 1213745-1SDE BATTERY TOOL (Kit) 1213890-2/-5 for pin diesSDE 626 Head 679304-1 + accessoriesSDE Electric Terminator 1490076-2SDE Bench Press Adapter 1579000-8 + Press 1481004-7

Predominately used on open-barrel terminals.These Dies are ideally suited to R&D prototyping, networking, commercial & industrial and all manor of maintenace applications.


Part Number Description mm² (AWG) or other91387-2 4.2 PE series 0.15 - 0.4 (26-22)91388-2 4.2 PE Series 0.4 - 1.0 (22-18)1891358-1 AMP EI Receptacle 0.15 - 0.6 (26-20)58448-3 AMPLIMITE HD-20 [28-20]90800-2 AMPLIMITE HD-22 0.08 - 0.4 (28-22)58641-2 AMPMODU IV, V 0.15 - 0.4 (26-22)217212-2 Closed End Splice 1.0 - 6.0 (18-10)90872-2 COMM 0.93 mm 0.2 - 1.0 (24-18)90574-2 Commercial MATE-N-LOK 0.2 - 0.96 (24-18)90575-2 Commercial MATE-N-LOK 0.6 - 2.5 (20-14)58517-2 CST-100 0.15 - 0.4 (26-22)58548-2 EI Receptacle 0.15 - 0.6 (26-20)58652-2 FASTON 2.8 (.110) Receptacle 0.6 - 1.5 (20-16)58524-2 FASTON 6.3 [.250] Receptacle 1.0 - 2.5 (18-14)91304-2 Junior Power TIMER 2.8 (SWS) & Micro TIMER 0.5 - 1.0 (22-18)58603-2 Junior Power TIMER; TAB 2.8 0.75 - 2.5 (20-14)1752938-2 MATE-N-LOK 3.5 (.140) 0.75 - 1.64 (18-16)90760-2 Mini Universal MATE-N-LOK [20-16]90759-2 Mini Universal MATE-N-LOK [22-18]90758-2 Mini Universal MATE-N-LOK 0.15 - 0.4 (26-22)58707-2 Mini-Universal MATE-N-LOK 0.6 - 1.5 (20-16)58522-2 MULTILOCK 040 0.4 - 0.6 (22-20)90652-2 MULTILOCK 040 MkII 0.4 - 1.0 (22-18)90653-2 MULTILOCK 070 0.4 - 0.6 (22-20)58606-2 Pin/Socket Ø1.5 & Ø2.5 (SWS) 1.0 - 2.5 (18-14)58593-2 Power Quadlock 1.5 - 3.0 (16-14)58594-2 Power Quadlock 4.0 (12)58595-2 Power Quadlock (SWS) 1.5 - 2.5 (16-14)58596-2 Power Quadlock (SWS) 4.0 (12)58614-2 SL-156 0.2 - 1.0 (24-18)58583-2 SUPERSEAL 1.5 series 0.5 - 1.0 (22-18)58495-2 TYPE III+; TYPE VI 0.08 - 1.5 (28-16)58628-2 ULTRA FAST (excluding Flag Terminals) 0.15 - 2.5 (26-14)58630-2 ULTRA FAST 4.0 - 6.0 (12-10)90546-2 Universal MATE-N-LOK 0.5 - 2.1 (20-14)

Ins. Ø1.53-3.30 mm90547-2 Universal MATE-N-LOK 0.5 - 2.1 (20-14)

Ins. Ø3.30-5.08mmOnly the most popular options are listed here, please use our online search by terminal PN to find the right tool for your application, and contact us

where information is unclear or missing - there may well be something available for your requirement.


SDE PRO-CRIMPER III

Features:Accepts all SDE Shoulder & Pin DiesRatchet mechanism ensures complete crimp cycleEmergency ratchet release featureErgonomic non-slip handlesApproximate weight 0.59 kg (1.3 lbs)

354940-1 - Base Tool without Die-setAn alternative to SDE PEW 12 & SDE DA hand tools, but with different features and a different geometry


Part Number Description mm² (AWG) or other58448-2 AMPLIMITE HD-20 [28-20]90800-1 AMPLIMITE HD-22 0.08 - 0.4 (28-22)90760-1 Mini Universal MATE-N-LOK [20-16]90759-1 Mini Universal MATE-N-LOK [22-18]790163-1 Modular Plug 8 Position Shielded 0.15 - 0.2 (26-24)58433-3 PIDG, PLASTI-GRIP - RBY All Types including PIDG FASTON Flag 22-18 & 16-14 0.4 - 6.0 (22-10)58593-1 Power Quadlock 1.5 - 3.0 (16-14)58594-1 Power Quadlock 4.0 (12)58595-1 Power Quadlock (SWS) 1.5 - 2.5 (16-14)58596-1 Power Quadlock (SWS) 4.0 (12)58546-1 SOLISTRAND Terminals & Splices 0.4 - 6.0 (22-10)58546-2 SOLISTRAND Terminals & Splices 0.4 - 6.0 (22-10)


SDE DA Hand Tool

Features:Accepts all SDE Shoulder & Pin DiesHigh mechanical advantage for enhanced user comfortRatchet mechanism ensures complete crimp cycleEmergency ratchet release featureErgonomic non-slip handlesApproximate weight 0.59 kg (1.3 lbs)

1213745-1 - Base Tool without Die-setDesigned specifically for closed barrel applications. Image representative of type only


Die-set - SDE SA

Features:Use in:SDE SA Hand Tool 9-1478240-0SDE BATTERY TOOL (Kit) 1725837-2/-5 for shoulder diesSDE 626 Head 679304-1 + accessoriesSDE Electric Terminator 1490076-2SDE Bench Press Adapter 1579000-8 + Press 1481004-7

(not for use in SDE PRO-CRIMPER III Hand Tool 354940-1)

These dies can have up to five crimp positions and are NOT suitable for use in the SDE Procrimper III Hand Tool Image representative of type only

Part Number Description mm² (AWG) or other2063030-1 PIDG, PLASTI-GRIP Terminals & Splices

with Terminal Locator[22-10]

2063379-2 Universal MATE-N-LOK 0.5 - 2.0 Ins. Ø1.4-2.4mm


Die-set - SDE SA Plus

Features:Use in:SDE PEW 12 Hand Tool 9-1478240-0SDE BATTERY TOOL (Kit) 1213890-2/-5 for pin diesSDE 626 Head 679304-1 + accessoriesSDE Electric Terminator 1490076-2SDE Bench Press Adapter 1579000-8 + Press 1481004-7

(not for use in SDE PRO-CRIMPER III Hand Tool 354940-1)

These dies can have up to five crimp positions and are NOT suitable for use in the SDE Procrimper III Hand Tool Image representative of type only

Part Number Description mm² (AWG) or other9-1478247-0 Coax - GREENPAR BT20039-1478243-0 Coax - GREENPAR PSF 1/2M, Belden 8281, TM

32059-1478248-0 Coax - GREENPAR RG 174, 178, 188...

See 408-86989-1478245-0 Coax - GREENPAR RG 174, 179, 187...

see 408-86949-1478242-0 Coax - GREENPAR RG 55, 58, 59, 62...

see 408-86949-1478246-0 Coax - GREENPAR RG 9, 58, 141...

see 408-86942063583-2 HTS: HE/HA; HN D; HVT Contacts 0.14 - 4.02063041-2 Micro Quadlok 0.25 - 0.5 (24-22)2031973-2 Universal MATE-N-LOK 0.2 - 2.0




SDE SA

Features:Accepts all SDE; Shoulder, Pin & Plus DiesRatchet mechanism ensures complete crimp cycleVirtually a straight action jaw closureEasy access ratchet releaseHandle pressure adjustment with locking deviceErgonomic non-slip handlesApproximate weight 0.59 kg (1.3 lbs)

9-1478240-0 - Base Tool without Die-setAn alternative to PRO-CRIMPER III & SDE DA hand tools, but with different features and a different geometry


Part Number Description mm² (AWG) or other9-1478239-0 Coax - GREENPAR RG 8, 213...

See 408-86952063583-1 HTS: HE/HA; HN D; HVT Contacts 0.14 - 4.01752938-1 MATE-N-LOK 3.5 (.140) 0.75 - 1.64 (18-16)91391-1 Micro MATE-N-LOK 0.06 - 0.5 (30-20)2063041-1 Micro Quadlok 0.25 - 0.5 (24-22)2031973-1 Universal MATE-N-LOK 0.2 - 2.0

Ins. Ø1.0-3.3mm2063379-1 Universal MATE-N-LOK 0.5 - 2.0



Die-set - SDE Premium

Features:Insulation crimp height adjustmentTerminal locator & wire stop

Use in:SDE BATTERY TOOL (Kit) 1213890-2 for pin diesSDE Electric Terminator 1490076-2

Note: The Specifications shown against the Dies listed are only applicable when using terminals and wires recommended for the relevant industry

These dies are based on the Double Action Hand Tools used in Aerospace & Military applications. Image representative of type only

Part Number Description mm² (AWG) or other91964-2 PIDG, PLASTI-GRIP Terminals & Splices - equivalent crimp to 47386

Qualified; Mil-T-7928; LUL RSE 024 pt6 & EE6161Marks the applied product with a two dot indent code.

0.4 - 1.5 (22-16)

91963-2 PIDG, PLASTI-GRIP Terminals & Splices - equivalent crimp to 47387Qualified; Mil-T-7928; LUL RSE 024 pt6 & EE6161Marks the applied product with a two dot indent code.

1.5 - 2.5 (16-14)0.6 - 1.5 (20-16) HD

91965-2 PIDG, PLASTI-GRIP Terminals & Splices - equivalent crimp to 59239-4Qualified; Mil-T-7928; LUL RSE 024 pt6 & EE6161Marks the applied product with a two dot indent code.

4.0 - 6.0 (12-10)



SDE BATTERY TOOL Kit

Features:Over 100 crimps per chargeCompact - only 3560mm (14") long and weighs 1.57kg (3.48lbs)

The Tool Kit is supplied in a durable plastic carry case and includes:Battery Tool with the relevant SDE HeadBattery Charger 220 vTwo Batteries

for more information, please see the Power Assist section

Convert your existing Hand Tools into Powered!1213890-2 SDE Pin Dies, CLOSED head (EU Power Plug)1213890-5 SDE Pin Dies, CLOSED head (UK Power Plug)1725837-2 SDE Shoulder Dies, OPEN head (EU Power Plug)1725837-5 SDE Shoulder Dies, OPEN head (UK Power Plug)


SDE Electric Terminator

Features:Ideal for low to medium production volumes.Accepts any SDE Die-setMains powered unit - no air requiredSwitchable 110v or 240v supplyCycle CounterTwo stage crimp cycle option

for more information please see the Power Assist section

1490076-2 - Portable Bench-top Unit with SDE Head & Foot SwitchImage representative of type only

SDE 626 Pneumatic

Features:Accepts any Pin / Shoulder SDE Die-setsAll pneumatic

Options for SDE 626 Head 679304-1:Tool Holder with Ratchet 356302-1 (pictured)or Tool Holder without Ratchet 189767-1andHand held power unit 189721-1 (pictured)or Foot actuated Power Unit 189722-1

for more 626 options please see the Power Assist section

Ideal for low to medium production volumes.Image representative of type only

Part Number Description mm² (AWG) or other679304-1 Head Only - requires Tool Holder & Power Unit 4.0 - 6.0 (12-10)1213855-1 Tool assembly comprising; 679304-1, 356302-1 & 189721-1 4.0 - 6.0 (12-10)



SDE Bench Press Adapter

Features:Adapts Bench Top Press SSC- 2FP (1481004-7 pictured) to take all SDE Shoulder & Pin Dies

for more information on the Press and Press options, please see the Power Assist section

1579000-8 - Adapter onlyImage representative of type only

General Hand Tool Types Revised: January 2010

CERTI-CRIMP II SAHT

Features:Fixed diesStraight action jaw closureRatchet mechanism ensures complete crimp cycleEmergency only ratchet releaseTerminal/wire positioning aids & Ins. adjustment on most toolsErgonomic non-slip handlesApproximate weight 0.59 kg (1.3 lbs)

Standard Straight Action Hand Tool DesignWidely used in the Aircraft and Military industries Image representative of type only

Part Number Description mm² (AWG) or other91572-1 AMP CT 2.0 Receptacle 0.12 - 0.4 (26-22)91576-1 AMP DYNAMIC D-2 0.08 - 0.22 (28-24)91595-1 AMP DYNAMIC D-2 0.4 - 1.0 (22-18)91559-1 AMP DYNAMIC D-3 0.2 - 0.6 (24-20)91558-1 AMP DYNAMIC D-3 0.6 - 1.5 (20-16)91549-1 AMPLIMITE HD-20 0.08 - 0.22 (28-24)91503-1 AMPLIMITE HD-20 0.08 - 0.6 (28-20)91548-1 AMPLIMITE HD-20 0.08 - 0.6 (28-20)

No Ins. Crimp91525-1 AMPLIMITE HD-20 0.15 - 0.4 (26-22)91513-1 AMPLIMITE HD-20 0.4 - 1.0 (22-18)

No Ins. Crimp91520-1 AMPLIMITE HD-22 0.08 - 0.4 (28-22)91537-1 AMPMODU II FFC 0.15 - 0.4 (26-22)91516-1 AMPMODU IV 0.05 - 0.6 (30-20)91517-1 AMPMODU IV, V 0.15 - 0.4 (26-22)91512-1 Commercial MATE-N-LOK 0.2 - 0.96 (24-18)

Ins. Ø1.52-2.54mm91504-1 Commercial MATE-N-LOK 0.6 - 2.5 (20-14)1901963-1 MATE-N-LOK 3.5 (.140) 0.5 - 2.1 (20-14)91502-1 Micro MATE-N-LOK 0.05 - 0.12 (30-26)91501-1 Micro MATE-N-LOK 0.2 - 0.6 (24-20)91540-1 Mini Tandem-Spring Pin 0.03 - 0.4 (32-22)91536-1 Mini-Universal MATE-N-LOK "F" Ins. Crimp [20-16]91529-1 Mini-Universal MATE-N-LOK 0.15 - 0.4 (26-22)91522-1 Mini-Universal MATE-N-LOK 0.4 - 1.0 (22-18)91594-1 Mini-Universal MATE-N-LOK, type "O" Ins. Crimp 0.5 - 1.42 (20-16)91577-1 MULTILOCK 040 0.4 - 0.6 (22-20)91588-1 MULTILOCK 040 MkII 0.6 - 1.0 (20-18)91542-1 TYPE III+ 0.2 - 0.6 (24-20)91505-1 TYPE III+ 0.2 - 1.42 (24-16)

Ins. Ø1.14-2.54mm91523-1 TYPE III+ 0.2 - 1.5 (24-16)

Ins. Ø2.03-2.54mm91521-1 TYPE III+ 1.0 - 2.5 (18-14)91515-1 TYPE III+; Type VI; Commercial MATE-N-LOK 0.05 - 0.6 (30-20)91510-1 Universal MATE-N-LOK 0.2 - 0.96 (24-18)91506-1 Universal MATE-N-LOK 1.2 - 2.1 (16-14)




CERTI-CRIMP II SAHT - Short Handle


Ideal for working in confined spacesWidely used in the Aircraft and Military industries Image representative of type only

Part Number Description mm² (AWG) or other1901611-2 PIDG STRATO-THERM Terminals & Splices 0.2 - 0.6 (24-20)1901600-2 PIDG STRATO-THERM Terminals & Splices 1.0 - 1.5 (18-16)


CERTI-CRIMP II SAHT - Long Handle


Low handle force for ease of operationWidely used in the Aircraft and Military industries Image representative of type only

Part Number Description mm² (AWG) or other1901611-1 PIDG STRATO-THERM Terminals & Splices 0.2 - 0.6 (24-20)1901600-1 PIDG STRATO-THERM Terminals & Splices 1.0 - 1.5 (18-16)



CERTI-CRIMP II SAHT - Head Assy (Square)

Features:Fixed DiesStraight action jaw closureRatchet mechanism ensures complete crimp cycleEmergency only ratchet releaseTerminal/wire positioning aids & Ins. adjustment on most tools

Use with:1213805-[ ] Battery Tool Kit1213860-[ ] Adapter, Electric Terminator

Head only for use with Power Assist optionsImage representative of type only

Part Number Description mm² (AWG) or other1-1901611-1 PIDG STRATO-THERM Terminals & Splices 0.2 - 0.6 (24-20)1-1901600-2 PIDG STRATO-THERM Terminals & Splices 1.0 - 1.5 (18-16)


CERTI-CRIMP II SA Battery Tool Kit

Features:Heads can be removed from Hand Tools, or are also available as a [-3] option.Example 91500-1 CERTI-CRIMP II SAHT; handles can be removed and the head used with this kit. Alternatively 91500-3 (head only) is also available.

Over 100 crimps per chargeCompact - only 360mm (14") long and weighs 1.57kg (3.48lbs)

The Tool Kit is supplied in a durable plastic carry case and includes:Battery Tool with the relevant CERTI-CRIMP II SAHT AdapterBattery Charger 230 vTwo Batteries


Convert your existing Hand Tools into Powered!1213805-2 - Kit only without Head1213805-5 - Kit only without Head (GB Power Plug)


Adapter - CERTI-CRIMP II to Electric Terminator

Features:For use with Electric Terminator 539630-1 and any CERTI-CRIMP II SAHT Head.

Heads can be removed from Hand Tools, or are also available as a [-3] option.Example 91500-1 CERTI-CRIMP II SAHT; the head can be removed from the handles and used along with this adapter on the Electric Terminator . Alternatively 91500-3 (head only) is also available.



Double Action Hand Tool

Features:Fixed diesRatchet mechanism ensures complete crimp cycleEmergency only ratchet releaseTerminal/wire positioning aids & Ins. adjustment on many toolsErgonomic non-slip handlesApproximate weight 0.54 kg (1.2 lbs)

Note: The approvals shown against the tools listed are only applicable when using terminals and wires recommended for the relevant industry.Widely used in Aircraft and Military applications


Part Number Description mm² (AWG) or other45216 PIDG Closed End Splice 1.0 - 1.5 (18-16)47386 PIDG & PLASTI-GRIP Terminals; PIDG Splices

Standard tool for GB Railways - Qualified; Mil-T-7928/7; LUL RSE 024 pt6 & EE6161Marks the applied product with a one dot indent code.

0.4 - 1.5 (22-16)

47386-5 PIDG & PLASTI-GRIP Terminals; PIDG SplicesFrench Special - Qualified; Mil-T-7928 - AMP specified levelMarks the applied product with a one dot indent code.Includes French Instruction Sheet

0.4 - 1.5 (22-16)

47387 PIDG & PLASTI-GRIP Terminals; PIDG SplicesStandard tool for GB Railways - Qualified; Mil-T-7928; LUL RSE 024 pt6 & EE6161Marks the applied product with a two dot indent code.

1.25 - 2.0 (16-14)0.6 - 1.5 (20-16) HD

47386-4 PIDG & PLASTI-GRIP Terminals; PIDG Splices & FASTONEMEA Special - Qualified; Mil-T-7928 - AMP specified level for Ringtongues onlyMarks the applied product with a one dot indent code.

0.4 - 1.5 (22-16)

47387-7 PIDG & PLASTI-GRIP Terminals; PIDG Splices & FASTONEMEA Special - Qualified; Mil-T-7928 - AMP specified level for Ring Tongues onlyMarks the applied product with a two dot indent code.

1.5 - 2.5 (16-14)0.6 - 1.5 (20-16) HD

90035-3 PIDG FASTON - Special GB Railways ToolQualified; LUL RSE 024 pt6 & EE6161

0.4 - 1.0 (22-18)

90009-8 PIDG FASTON - Special GB Railways ToolQualified; LUL RSE 024 pt6 & EE6161

1.5 - 2.5 (16-14)

482930-1 Special French tool for PIDG FASTON 2.8 (.110) with crimp orientation at 90°Marks the applied product with a one dot indent code.

0.15 - 0.4 (26-22)

47907-1 PIDG Terminals & Splices 0.2 - 0.56 (24-20)46121 PIDG Terminals & Splices; PLASTI-GRIP Butt Splices

Marks the applied product with a one dot indent code0.15 - 0.4 (26-22)

47304 PIDG Terminals & Splices; PLASTI-GRIP Butt Splices for thin wall insulationMarks the applied product with a one dot indent code

0.15 - 0.4 (26-22)

525690 Special GB Aerospace PIDG & PLASTI-GRIP Ring Tongue Tool.Equivalent to 47386 but has special retaining pins/rings to reduce the risk of tool parts falling off whilst building and maintaining aircraft.

0.6 - 1.0 (20-18)

525691 Special GB Aerospace PIDG & PLASTI-GRIP Ring Tongue Tool.Equivalent to 47387 but has special retaining pins/rings to reduce the risk of tool parts falling off whilst building and maintaining aircraft.

1.25 - 2.0 (16-14)

69363 SOLISTRAND Terminals & Splices - Standard Tool.Qualified; Mil-T-7928; LUL RSE 024 pt6 & EE6161

0.15 - 0.6 (26-20)

49935 SOLISTRAND Terminals & SplicesQualified; Mil-T-7928; LUL RSE 024 pt6 & EE6161

0.4 - 6.0 (22-10)

525693 Special tool for SOLISTRAND Terminals & Splices (GB)Equivalent to 49935 but has special retaining pins/rings to reduce the risk of tool parts falling off whilst building and maintaining aircraft.

0.4 - 6.0 (22-10)

49592 SOLISTRAND Terminals & SplicesQualified; Mil-T-7928; LUL RSE 024 pt6 & EE6161

2.5 - 4.0 (14-12)

46447 SOLISTRAND STRATO-THERM High Temp & Heat Resistant Terminals & Splices 0.4 - 6.0 (22-10)46673 STRATO-THERM Uninsulated Terminals & Splices 0.4 - 1.5 (22-16)46673-1 STRATO-THERM Uninsulated Terminals & Splices [thin wall cable] 0.4 - 1.5 (22-16)



Double Action Hand Tool Battery Tool Kit

Features:Example 47386 DAHT; handles can be removed and the head used with this kit.


The Tool Kit is supplied in a durable plastic carry case and includes:Battery Tool with the relevant DAHT AdapterBattery Charger 230 vTwo Batteries


Convert your existing Hand Tools into Powered!1213804-2 - Kit only without Head1213804-5 - Kit only without Head (GB Power Plug)


Adapter - Double Action Hand Tool to 626 Pneumatic

Features:Heads can be removed from Hand Tools, example:the Handles from 47386 can be removed and the head used with this Adapter (includes cam).

Also required:Hand held power unit 189721-1orFoot actuated Power Unit 189722-1


.



C-Head SAHT

Features:Interchangeable DiesStraight action jaw closureRatchet mechanism ensures complete crimp cycleEmergency only ratchet releaseApproximate weight 0.86 kg (1.9 lbs)

69710-1 - Base Tool without Die-setWidely used in Aircraft and Military applicationsCan be used with all C-Head SAHT Dies


C-Head SAHT - LD

Features:Interchangeable DiesStraight action jaw closureRatchet mechanism ensures complete crimp cycleEmergency only ratchet releaseErgonomic non-slip handlesApproximate weight 0.5 kg (1.1 lbs)

1901260-1 Base Tool without Die-setA light duty alternative to 69710-1Can be used with all C-Head SAHT Dies EXCEPT: - Die-set - C-Head SAHT - HD - Through Splice applicatons



Die-set - C-Head SAHT

Features:Use in:Hand Tool Frame 69710-1Hand Tool Frame 1901260-1 (see restrictions)

Battery Tool Kits: Open Head 1213840-[ ] Closed Head 1213819-[ ]

Adapters for C-Head Dies: Electric Terminator 1901556-1 Press SSC- 2FP 8-1481221-3

A range of Die-sets for many premium crimp applicationsImage representative of type only

Part Number Description mm² (AWG) or other58212-1 AMPLIMITE RG 142, 142A, 142B576711 PIDG STRATO-THERM Terminals with PTFE or PEEK for thin-wall Insulation 0.2 - 0.4 (24-22)576720 PIDG STRATO-THERM Terminals with PTFE or PEEK for thin-wall Insulation 0.5 (22)576715 PIDG STRATO-THERM Terminals with PTFE or PEEK for thin-wall Insulation 1.0 (18)576714 PIDG STRATO-THERM Terminals with PTFE or PEEK for thin-wall Insulation 1.5 (16)47807-1 PIDG, PLASTI-GRIP Terminals & Splices 1.5 - 2.5 (16-14)47806-2 PIDG, PLASTI-GRIP, Terminals & Splices 0.4 - 1.5 (22-16)1-539634-9 Pin / Socket size 8 Gore Cable Type:

GSC-03-81748-00Only the most popular options are listed here, please use our online search by terminal PN to find the right tool for your application, and contact us


Die-set - C-Head SAHT - HD

Features:Use in:Hand Tool Frame 69710-1

Adapters for C-Head Dies: Electric Terminator 1901556-1 Press SSC- 2FP 8-1481221-3

A range of Heavy Duty Die-sets for many premium crimp applicationsImage representative of type only

Part Number Description mm² (AWG) or other59993-1 AMPLIMITE 8 (10)69735 PIDG STRATO-THERM Terminals & Splices with PTFE Insulation 4.0 - 6.0 (12-10)576716 PIDG STRATO-THERM Terminals with PTFE or PEEK for thin-wall Insulation 2.5 (14)576742 PIDG STRATO-THERM Terminals with PTFE or PEEK for thin-wall Insulation 4.0 (12)576723 PIDG STRATO-THERM Terminals with PTFE or PEEK for thin-wall Insulation 6.0 (10)47808-6 PIDG, PLASTI-GRIP Terminals & Splices 4.0 - 6.0 (12-10)90145-1 TYPE XII Contact 2.5 - 4.0 (14-12)90140-1 TYPE XII Contact 6.0 - 10.0 (10-8)58380-1 Universal MATE-N-LOK 3.0 (12)58380-2 Universal MATE-N-LOK 5.0 (10)



C-Head SAHT Battery Tool Kit


The Tool Kit is supplied in a durable plastic carry case and includes:Battery Tool with the relevant C-Head SAHT AdapterBattery Charger 230 vTwo Batteries


1213819-2 - CLOSED head1213819-5 - CLOSED head (GB Power Plug)1213840-2 - OPEN head1213840-5 - OPEN head (GB Power Plug)


Adapter - C-Head SAHT to Bench Press SSC-2FP

Features:Adapts Bench Top Press SSC- 2FP (1481004-7 pictured) to take C-Head SAHT Dies


8-1481221-3 - Adapter onlyImage representative of type only

Adapter - C-Head SAHT to Electric Terminator

Features:Adapts the Electric Terminator 539630-1 to take C-Head SAHT Dies




Heavy Head Hand Tool

Features:Fixed diesStraight action jaw closureRatchet mechanism ensures complete crimp cycleEmergency only ratchet releaseTerminal/wire positioning aids & Ins. adjustment on most toolsApproximate weight 0.95 kg (2.1 lbs)

Note: The specifications shown against the tools listed are only applicable when using terminals recommended for the relevant industryWidely used in Aircraft and Military applications


Part Number Description mm² (AWG) or other234170-1 AMP DYNAMIC D-5 1.5 - 2.5 (16-14)234171-1 AMP DYNAMIC D-5 4.0 - 6.0 (12-10)1366044-1 AMP DYNAMIC D-5 Receptacle 8.0 (10)90246-1 PIDG FASTON - Standard tool 2.5 - 4.0 (14-12)90276-2 PIDG FASTON

Qualified; LUL RSE 024 pt6 & EE61614.0 - 6.0 (12-10)1.5 - 2.5 (16-14) HD

484364-1 PIDG STRATO-THERM Terminals & Splices 1.0 (18)576782 Special GB Aerospace tool for PIDG STRATO-THERM Terminals with PTFE or

PEEK for thin-wall InsulationQualified to BS 4G178

2.5 (14)

576783 Special GB Aerospace tool for PIDG STRATO-THERM Terminals with PTFE or PEEK for thin-wall InsulationQualified to BS 4G178

4.0 (12)


6.0 (10)


0.2 - 0.4 (24-22)


0.6 (20)


1.0 (18)


1.5 (16)

59239-4 PIDG, PLASTI-GRIP Terminals & Splices - Standard tool for GB RailwaysQualified; Mil-T-7928; LUL RSE 024 pt6 & EE6161Marks the applied product with a one dot indent code.

3.0 - 5.0 (12-10)1.5 - 2.5 (16-14) HD

59287-2 PIDG, PLASTI-GRIP Large Expansion Terminals & Splices 4.0 - 6.0 (12-10)(16-14) HD

525692 Special GB Aerospace PIDG & PLASTI-GRIP Ring Tongue Tool.Equivalent to 59239-4 but has special retaining pins/rings to reduce the risk of tool parts falling off whilst building and maintaining aircraft.

4.0 - 6.0 (12-10)

69355 SOLISTRAND Terminals & Splices 10.0 (8)59461 STRATO-THERM Uninsulated Terminals & Splices with Insulation Support 4.0 - 6.0 (12-10)

(16-14) HD90382-2 TYPE XII Contact 1.5 - 4.0 (16-12)90384-1 TYPE XII Contact 6.0 - 10.0 (10-8)



Heavy Head Hand Tool Battery Tool Kit

Features:Heads can be removed from many Heavy Head Hand Tools, example:the Handles from 59239-4 can be removed and the head used with this kit.See Instruction sheet 409-10068 for a list of compatible tools


The Tool Kit is supplied in a durable plastic carry case and includes:Battery Tool with Heavy Head AdapterBattery Charger 230 vTwo Batteries


Convert your existing Hand Tools into Powered!1901235-2 - Kit only without head1901235-5 - Kit only without head (GB Power Plug)


Adapter - Heavy Head to 626 Pneumatic

Features:Heads can be removed from Hand Tools, example:the Handles from 59239-4 can be removed and the head used with this Adapter on the 626 Pneumatic system.

Also required:Adapter Holder with Ratchet 356304-1or Adapter Holder without Ratchet 189928-1andHand held power unit 189721-1or Foot actuated Power Unit 189722-1



Reel-Fed CERTI-LOK

Features:Terminal feeding and cutting deviceStraight action jaw closureRatchet mechanism ensures complete crimp cycleEasy access ratchet releaseHandle pressure adjustment with locking deviceEgonomic non-slip handles

A unique tool that applies terminals from special small reelsImage representative of type only

Part Number Description mm² (AWG) or other734643-1 AMPLIVAR734203-1 AMPMODU IV 0.12 - 0.14 (26)734204-1 AMPMODU IV 0.2 -0.56 (24-20)734870-2 MICRO MATCH COSI contact 0.08 - 0.2 (28-24)734870-1 MICRO MATCH COSI contact 0.2 - 0.6 (24-20)539608-1 MODU II 0.02 - 0.20 (32-24)734216-1 TYPE III+ 0.2 - 1.5 (24-16)


CERTI-LOK

Features:Interchangeable DiesStraight action jaw closureRatchet mechanism ensures complete crimp cycleEasy access ratchet releaseHandle pressure adjustment with locking deviceErgonomic non-slip handlesApproximate weight 0.64 kg (1.4 lbs)

169400 - Base Tool without Die-setImage representative of type only

Adapter - CERTI-LOK to Electric Terminator

Features:Adapts the Electric Terminator 539630-1 to take CERTI-LOK Dies


169411 - Adapter onlyImage representative of type only


PEZ 100

Features:Interchangeable DiesFlap type terminal locatorStraight action jaw closureRatchet mechanism ensures complete crimp cycleEasy access ratchet releaseHandle pressure adjustment with locking deviceEgonomic non-slip handles

539717-1 - Base Tool without Die-set1579000-1 - Base Tool without Die-set Long Handles Image representative of type only

ERGOCRIMP

Features:Interchangeable DiesVirtually a straight action jaw closureRatchet mechanism ensures complete crimp cycleEasy access ratchet releaseHandle pressure adjustment with locking deviceEgonomic non-slip handlesApproximate weight 0.59 kg (1.3 lbs)

Spare parts Kit 539635-2 (excluding main spring)Main Spring PN 1579005-1

539635-1 - Base tool without Die-setNote: This tool is not compatible with SDE Dies Image representative of type only

Tetra-Crimp Hand Tool

Features:Interchangeable DiesRatchet mechanism ensures complete crimp cycleTamper proof ratchet release settingEmergency ratchet release featureTerminal loactor / support and wire stop on many toolsApproximate weight 0.64 kg (1.4 lbs)Egonomic non-slip handles

58078-3 - Base Tool without Die-setImage representative of type only

Part Number Description mm² (AWG) or other58052-3 Die-set for ULTRA FAST 0.15 - 0.4 (26-22)90390-3 Die-set for ULTRA FAST (including Flag Terminals) 0.4 - 1.0 (22-18)90391-3 Die-set for ULTRA FAST (including Flag Terminals) 1.5 - 2.5 (16-14)58079-3 Die-set for ULTRA FAST PLUS 0.4 - 1.0 (22-18)58080-3 Die-set for ULTRA FAST PLUS 1.5 - 2.5 (16-14)



Mini CERTI-LOK

Features:Fixed diesStraight action jaw closureRatchet mechanism ensures complete crimp cycleEasy access ratchet releaseHandle pressure adjustment with locking deviceEasy terminal positioning with 'Flap Locator' (some tools)Egonomic non-slip handlesApproximate weight 0.46 kg (1.0 lbs)

A light weight and compact tool for many commercial applicationsImage representative of type only

Modular Mini CERTI-LOK

Features:Heads with identical features to the Mini Certilok tool

Choice of two handle lengths:2-1579005-1 Short Handle2-1579005-2 long Handle

Interchangerbility via snap-in pins.

Based on the Mini Certi-Lok toolImage representative of type only

C-Frame Hand Tool

Features:Interchangeable DiesDouble action jaw closureRatchet mechanism ensures complete crimp cycleEasy access ratchet releaseHandle pressure adjustment with locking deviceEgonomic non-slip handlesApproximate weight 0.55 kg (1.2 lbs)

6-1419172-9 - Base Tool without Die-setImage representative of type only

Part Number Description mm² (AWG) or other1583684-1 Die-set for ADK Series Back Shell 6.0 mm Cable Dia Max1583684-2 Die-set for ADK Series Back Shell 7.5 mm Cable Dia Max1583684-3 Die-set for ADK Series Back Shell 8.5 mm Cable Dia Max1583684-4 Die-set for ADK Series Back Shell 9.5 mm Cable Dia Max948761-1 Complete tool for HDE20 Ferrule Cable Ø4.8 - 6.3948761-2 Complete tool for HDE 20 Ferrule Cable Ø6.3 - 8.2948761-3 Complete tool for HDE20 Ferrule cable Ø8.2 - 11.1734566-1 Complete tool for N Series 50 & 70 ohm



D-Frame Tool

Features:Fixed Die-setsSmall and lightweightRatchet mechanism ensures complete crimp cycleEasy access ratchet releaseHandle pressure adjustment with locking deviceEgonomic non-slip handlesApproximate weight 0.55 kg (1.2 lbs)


Part Number Description mm² (AWG) or other947488-1 Coax - BNC, TNC Cable Dia 5 & 6mm947679-1 HE 13 / 14 Crimp-on Snap-in 0.08 - 0.2 (28-24)2-1579002-0 Wire Wire End Ferrrules (Square crimp form) 0.5 - 6.0 (22-10)


Trapezium Crimp Tool

Features:Ratchet mechanism ensures complete crimp cycleEasy access ratchet releaseHandle pressure adjustment with locking deviceEgonomic non-slip handles

Special Trapezium crimp tool for Wire End Ferrule applicationsImage representative of type only

Part Number Description mm² (AWG) or other734641-2 Wire End Ferrules (trapezium crimp form) 0.14 - 6.0 (26-10)734641-3 Wire End Ferrules (trapezium crimp form) 0.5 - 10 (22-6)734641-4 Wire End Ferrules (trapezium crimp form) 10.0 - 16.0 (8-6)



Square Crimp Tool

Features:Ratchet mechanism ensures complete crimp cycleEasy access ratchet releaseHandle pressure adjustment with locking deviceEgonomic non-slip handles

Special Square crimp tool for Wire End Ferrule applicationsImage representative of type only

Part Number Description mm² (AWG) or other539660-1 Wire Wire End Ferrrules (square crimp form) 0.08 - 6.0 (28-10)539661-1 Wire Wire End Ferrrules (square crimp form) 0.75 - 10 (20-8)7-1579014-0 Wire End Ferrules DIN 46228 Pt. 1 & 4 - crimp length 13mm.

Crimp is indented on two sides only - (better for smaller sizes)0.08 - 10.0 (28-8)


Service Tool

Features:Interchangeable DiesRatchet mechanism ensures complete crimp cycleEasy access ratchet releaseHandle pressure adjustment with locking deviceEgonomic non-slip handlesApproximate weight 0.59 kg (1.3 lbs)



TERMI-POINT Hand Tool

Features:Pneumatic options (pictured)Interchangeable MandrelsTerminals fed from Reel


Part Number Description mm² (AWG) or other655032-1 Hand Tool without Mandrel for Maxi TERMI-POINT 0.2 - 0.56 (24-20)69526-2 Hand Tool without Mandrel 0.08 - 0.4 (28-22)69551-5 Mandrel (black) for 69526-2 0.08 (28)

Ins. Ø1.14-1.65mm69551-6 Mandrel (brown) for 69526-2 0.15 (26)

Ins. Ø0.56-1.14 mm871295-5 Mandrel (brown) for 871087-2 0.15 (26)

Ins. Ø0.76-1.40mm1-69411-9 Mandrel (brown) for 69526-2 0.15 (26)

Ins. Ø1.14-1.65mm655136-3 Hand Tool without Mandrel 0.2 - 0.4 (24-22)69551-9 Mandrel (red) for 69526-2 0.2 (24)

Ins. Ø0.74-1.23mm871295-2 Mandrel (red) for 871087-1 0.2 (24)



Ins. Ø1.1 -1.65mm1-69411-3 Mandrel (red) for 69526-2 0.2 (24)

Ins. Ø1.10-1.65mm871087-2 Hand Tool (pneumatic) without Mandrel 0.4 - 0.15 (22-26)69551-8 Mandrel (orange) for 69526-2 0.4 (22)

Ins. Ø0.87-1.23mm871295-3 Mandrel (orange) for 871087-2 0.4 (22)

Ins. Ø0.91-1.65mm1-69411-4 Mandrel (orange) for 69526-2 0.4 (22)

Ins. Ø1.14-1.65mm871295-1 Mandrel (yellow) for 871087-1 0.56 (22)

Ins. Ø0.91-1.65mm69561 Mandrel (yellow) for 654182-1 0.56 (22)

Ins. Ø1.17-1.65mm69561-1 Mandrel (yellow) for 654182-1 0.56 (22)

Ins. Ø1.68-2.16mm654182-1 Hand Tool without Mandrel 0.6 - 0.2 (20-24)871087-1 Hand Tool (pneumatic) without Mandrel 0.6 - 0.2 (20-24)



Service Kit Tool

Features:Tool-less Die changeRatchet mechanism ensures complete crimp cycleEmergency ratchet release featureErgonomic non-slip handlesApproximate weight 0.46 kg (1.0 lbs)

Ideal for Service and RepairImage representative of type only

Part Number Description mm² (AWG) or other3-1579000-0 Hand Tool Frame only - Service Kit Tool


Die-set - Service Kit Tool

Features:Upper & lower Dies are permanently joinedInterlocking Die-set holders

Use in Service Kit Tool 3-1579000-0

Build up your own kit!Image representative of type only

Part Number Description mm² (AWG) or other3-1579016-4 FASTON 6.3 [.250] 0.5 - 6.0 (22-10)3-1579016-1 PIDG, PLASTIGRIP Terminals & Splices 0.1 - 6.0 (26-10)

Green / Yellow3-1579016-2 PIDG, PLASTIGRIP Terminals & Splices 0.5 - 2.5 (22-14)

Red / Blue3-1579016-3 SOLISTRAND Terminals & Splices 0.5 - 6.0 (22-10)3-1579016-5 Wire End Ferrrules 0.25 - 10.0 (24-8)


Hand Tools for IDC Applications Revised: January 2010

Pistol Grip

Features:Interchangeable HeadsComplete cycle ratchect controlProduct automatically indexes after insertionHead rotates for user convenience

Specially Developed to cover a wide range of IDC products - these tools are ideal for small batch production and repair Image representative of type only

Part Number Description mm² (AWG) or other548053-1 AMP CT 2.0 Receptacle 2 to 28 ways1372039-1 AMP MONO-SHAPE MK II Tab connector 0.35 - 1.5 (24-16)528015-7 AMP MONO-SHAPE Tab connector 0.5 - 1.5 (22-16)539453-1 AMP multifitting MK II 0.35 - 1.0 (24-18)870088-3 AMPLIMITE HDE-20 0.05 - 0.6 (30-20)870086-2 AMPMODU MT Female Connector, Dual Row 0.15 - 0.4 (26-22)870086-3 AMPMODU MT Female Polarised Connectors, Dual Row 0.15 - 0.4 (26-22)946807-1 HE-13/14 (180°) 0.08 - 0.22 (28-24)945419-1 HE-13/14 (90°) 0.08 - 0.22 (28-24)549012-1 Modu w. pin housing 964144 1x4 way539638-1 Modu w. pin housing 964144 1x5 way734173-1 MT 6 0.4 - 1.0 (22-18)656154-1 MT Connector - Decrete wire 2 to 20 Posns734175-1 MT-6-M / Sonderversion 2 to 12 Posns656154-5 MT-EDGE 5.0 0.5 (22)658096-3 RV-100 MULTIPLEXER 16 Posn.

RV-100 32, 48, 64, 80, 96 Posn.; RV-100-4 32 Posn.0.05 - 0.35 (30-22)

873710-1 TANDEM-SPRING 2x13 way549013-1 TS Receptacle 1x4 way



Pistol Grip II

Features:Interchangeable HeadsComplete cycle ratchect controlProduct automatically indexes after insertionHead rotates for user convenience

58074-1 - Manual Handle without Head58075-1 - Pnuematic Handle without HeadIdeal for small batch production and repair


Part Number Description mm² (AWG) or other58372-1 Head only for AMP CT 2.0 2 to 28 ways58063-2 Head only, for AMPLIMITE HDE-20 0.05 - 0.6 (30-20)608868-1 Complete Tool, for AMPLIMITE HDE - 20 0.05 - 0.6 (30-20)58569-1 Head only for AMPMODU MTE Receptacle

Inserts crimped Contacts into Housing58336-1 Head only for AMPMODU MTE Receptacle 0.03 - 0.4 (30-22)937317-1 Complete Tool, for Mini CT MT 2 to 20 Posns58246-2 Head only for MTA 100 0.06 - 0.4 (30-22)58579-1 Complete Tool, for MTA 100 0.08 - 0.4 (28-22)58246-1 Head only, for MTA 100 0.09 - 0.4 (28-22)58247-1 Head only, for MTA 156 & descrete wires 0.15 - 1.0 (26-18)58247-3 Head only, for MTA 156 Descrete Wire, Jacketed or Ribbon Cable applications 0.15 - 1.0 (26-18)58580-1 Complete Tool, for MTA 156 0.15 - 1.0 (26-18)58443-1 Head only for MTA-156 Discrete Wire Receptacles [26-18]

Ins. Ø2.41mm maxOnly the most popular options are listed here, please use our online search by terminal PN to find the right tool for your application, and contact us


Pistol Grip III

Features:Interchangeable HeadsComplete cycle ratchect controlProduct automatically indexes after insertion

1-528015-6 - Base Tool without HeadOrder Handle and Head separatelyIdeal for small batch production and repair


Part Number Description mm² (AWG) or other785900-1 Complete Tool for AMP MONOSHAPE734042-1 Head only for HE-13/14 (180°) 0.08 - 0.22 (28-24)734043-1 Complete Tool for HE 13/14 (180°) 0.08 - 0.22 (28-24)734040-1 Head only for HE-13/14 (90°) 0.08 - 0.22 (28-24)734041-1 Complete Tool for HE-13/14 (90°) 0.08 - 0.22 (28-24)870090-1 Complete Tool for MT Connector, Ribbon cable 2 to 20 Posns



Special Hand Tool for DUOPLUG 2.5

Features:Suitable for low volume production and repair work.The connector housing is placed in a support frame and the handles are partially closed, then the wire can be inserted up against the wire stop.Completely closing the handles pushes the wires into the IDC contacts and completes the terrnination.

549033-1 - complete toolImage representative of type only

Hand Tool - ANSLEY 779-2100

Features:One Stationary HandleOne Moveable HandleUpper PlattenLower Platten mounting PlateAccepts a range of Lower Platten Blocks to crimp a wide variety of products

1437000-6 for all STD DIP PlugsImage representative of type only

Part Number Description mm² (AWG) or other1-1437000-2 Platten Block - ANSLEY 609 / 622 Ribbon Cable Socket Connectors 10 to 60 Pos1437000-8 Platten Block - ANSLEY 609 Ribbon Cable Socket Connectors 10 to 64 Pos1-1437000-3 Platten Block - ANSLEY 622 Ribbon Cable Socket Connectors 10 to 60 Pos1437000-9 Platten Block - ANSLEY 622 Ribbon Cable Socket Connectors 10 to 64 Pos


Insertion / Extraction Tool Types Revised: January 2010

Standard Extraction Tool

Features:This standard tool design features a comfortable handle and snap-in/out protective cover. Users can stow the business end of the tool when not in use, to protect against inadvertent damage to product or personal injury.

Insert discrete terminals into connector housings or remove them, without causing damage to either the terminals or housings. Image representative of type only

Part Number Description mm² (AWG) or other1-1579007-1 AMP MCP 1.5k Receptacle; AMP MCP 1.5k (SWS) Receptacle1579007-1 AMP MCP 2.8 Receptacle1-1579007-3 AMP MCP 6.3/4.8k Receptacle1-1579007-7 AMP MCP 9.5 Tab; Maxi Power TIMER Receptacle1-1579008-6 AMP-DUAC Connectors1579007-9 AMPLIMITE HD-201-1579007-5 ECONOSEAL III LC 1.8 [.070]3-1579007-6 GET .064 Pin/Socket1579008-5 IEC-Terminal4-1579007-1 Locking Tab 3.3 Receptacle539764-1 MATE-N-LOK 3.5 (.140)1-1579007-0 MCON 1.2-CB Receptacle; MCON 1.2-CB Receptacle (SWS) - Secondary Lock1579007-8 MCON 1.2-CB; MCON 1.2-CB (SWS)5-1579007-3 MCON 1.2-LL; MCON 1.2-LL (SWS)5-1579008-2 MCON 2.8 Receptacle; MCON 2.8 Receptacle (SWS)6-1579007-3 Micro Power Quadlok5-1579007-5 Micro TIMER I539960-1 Micro TIMER II, III, IV; TAB 1.64-1579007-8 MQS6-1579007-0 MQS-Clean Body3-1579007-7 Pin Ø1.5 (Spare tube 3-1579007-8)1-1579007-8 Pin/Socket Ø2.5 (Spare tube 4-1579007-7)539967-1 Pin/Socket Ø4.0 (Spare tube 5-1579007-2)6-1579007-4 Power Quadlok1579007-2 RAIL Contact7-1579007-0 SENSOR-TAB 1.5; SENSOR-REC 1.5 Type II2-1579007-5 Standard & Junior Power TIMER (asymmetric Tab contacts)1-1579007-6 Standard & Junior Power TIMER Receptacle and (symmetric Tab contacts)1-1579007-4 Standard & Junior TIMER; FASTIN-FASTON & POSITIVE-LOK Tab 2.8, 4.8, 5.8, 6.34-1579007-3 Standard TIMER etc. Kit comprises; 1-1579007-4 & 1-1579007-69-1579007-1 SUPER-SEAL 1.5; MULTILOCK 0709-1579007-5 Universal MATE-N-LOK Contacts - only with Housing contact cavity Ø 3.55mm9-1579007-6 Universal MATE-N-LOK Socket 926884 / 926885 with Housing contact cavity Ø5.0539972-1 Universal MATE-N-LOK; Socket Ø1.5; TYPE II, III+; CI-2, -3, -H

(Spare tube 5-1579007-0)Only the most popular options are listed here, please use our online search by terminal PN to find the right tool for your application, and contact us



Extraction Tool

Features:Many different design types currently exist for our vast terminal range, which we continue to convert. If you would like the tool you use converted to our Standard design, want a custom kit or tools in this design for other manufacturers products please contact us, and where volumes permit we will be pleased to provide you with a quotation for your requirement.


Part Number Description mm² (AWG) or other723986-1 AMP DRAWER234168-1 AMP DYNAMIC D-3409158-1 AMP DYNAMIC D-5465195-1 AMP-LEAF913923-1 AMP UNIVERSAL Power Connector188688-1 AMP DUAC91285-1 AMPLIMITE HD-20726364-2 AMPLIMITE HD-22318813-1 AMPLIMITE size 8; POWERBAND .125843473-1 AMPMODU I, IV, V; TANDEM SPRING166645-1 AMPMODU IV, V843477-1 AMPMODU MTE; SHORT-POINT576721 COMBOLINE318837-1 COMM 093465644-1 Commercial MATE-N-LOK1276716-1 DYNAMIC D2937313-1 ECONOSEAL II 1.8 [.070]724712-1 ECONOSEAL III HC 6.3 [.250] Receptacle724713-1 ECONOSEAL III HC 6.3 [.250] Tab1102855-1 HTS HDM Contacts1102855-7 HTS HE/HA Contacts1102855-2 HTS HND Contacts1102855-8 HTS HSK Contacts1105855-4 HTS HSM Contacts1102855-5 HTS HSS Contacts1102855-3 HTS HVT Contacts91084-1 LOCKING CLIP753787-1 MIC MK-2 Receptacle B TYPE724763-1 MIC Mk-I Tab723735-1 MIC Mk-I&II843996-6 MICRO MATE-N-LOK189727-1 Mini-Universal MATE-N-LOK455822-2 MR Contacts1276565-1 MULTILOCK 025755430-1 MULTILOCK 040715131-1 MULTILOCK 040 MkII755430-2 MULTILOCK 070342578-1 PM IV Cable seal- dissassembly tool342576-1 PM IV Socket Ø3.0 mm724659-1 POSITIVE-LOK 187785084-1 SUPER-SEAL 1.5 (secondary lock of TAB Connector)965713-1 TAB 3.369357-3 TERMI-POINT 0.08 - 0.6 (28-20)91073-1 TWIN-LEAF305183-8 TYPE I; Miniature COAXICON726423 TYPE XII



Standard Insertion Tool

Features:This standard tool design features a comfortable handle and snap-in/out protective cover. Users can stow the business end of the tool when not in use, to protect against inadvertent damage or personal injury.


Part Number Description mm² (AWG) or other1-1579007-9 Pin/Socket Ø4.0


Insertion Tool

Features:Many different design types currently exist for our vast terminal range, which we continue to convert. If you would like the tool you use converted to our Standard design, want a custom kit or tools in this design for other manufacturers products – contact us, and where volumes permit we will be pleased to provide you with a quotation for your requirement.


Part Number Description mm² (AWG) or other380306-3 AMP 53 Series TAPER PIN552714-3 AMP Barrel Terminals 0.08 - 0.2 (28-24)552714-4 AMP Barrel Terminals 0.08 - 0.4 (28-22)552714-1 AMP Barrel Terminals 0.4 - 1.0 (22-18)58430-1 AMPLIMITE .050 Shielded Connectors726363-2 AMPLIMITE HD-22344525-1 ECONOSEAL III, High Current with Seal 0.5 - 3.0 (22-14)465665-1 FASTIN-FASTON 6.3 [.250] - requires Universal Handle 465629-11102855-6 HTS Contacts274250-2 MAG-MATE59839-1 MTA-156965702-1 Pin/Socket Ø1.5 & Ø2.5 (Insulation less than Ø2.1mm) Insulation less than Ø2.1mm965700-1 Pin/Socket Ø4.0342577-1 PM IV Cable seal - assembly tool658167-1 RV-100725830-1 Standard TERMI-POINT658033-1 TYPE F200893-2 TYPE II, III+826790-3 TYPE III+, CI-2 Socket - Cable Seal protection tool826791-1 TYPE III+, CI-2 Pin - Seal protection tool455830-1 Universal MATE-N-LOK; Mini Universal MATE-N-LOK1583255-1 Z-Pack HM-Zd Vertical Pin Header



Tee Handled Insertion Tool

Features:Comfortable moulded handleMoulded-in metal insert for long life


Part Number Description mm² (AWG) or other229384-1 AMP CHAMP Connectors91287-1 AMPLIMITE HDE-20525421-5 HE-13; HE-14 0.08 - 0.22 (28-24)1-525421-3 IDC Bulb Holder 5 mm 0.2 (24)525421-6 IDC FASTON 0.2 - 0.4 (24-22)59803-1 MTA 100 0.08 - 0.4 (28-22)59804-1 MTA 156 0.15 - 1.0 (26-18)


Insertion / Extraction Tool Kit

Features:Kits are supplied in a rugged plastic carry case

This standard tool design features a comfortable handle and snap-in/out protective cover. Users can stow the business end of the tool when not in use, to protect against inadvertent damage or personal injury.

Custom kits made to suit your specific requirements

Insert discrete terminals into connector housings or remove them, without causing damage to either the terminals or housings


Part Number Description mm² (AWG) or other4-1579010-0 Insertion / Extraction Tool Kit - Renault


Heavy Duty Crimp Equipment & Accessories Revised: January 2010

ROTA-CRIMP Hand Tool

Features:Very large wire range coveredSimply rotate the appropriate crimp nest into positionAvailable with and without full cycle ratchet mechanism

Generally used in Battery Lead applicationsImage representative of type only

Part Number Description mm² (AWG) or other600850 Tool without Ratchet for Battery Terminals & Lugs 10.0 - 120.0 (8-4/0)600850-1 Tool with ratchet for Battery Terminals & Lugs (pictured) 10.0 - 120.0 (8-4/0)601129-2 Tool with Ratchet for PLASTI-GRIP & Pre-insulated AMPOWER Terminals;

TERMINYL Terminals & SplicesSingle Crimp 10.0 - 35.0 (8-2)Dual Crimp 1/0


Bantam ROTA-CRIMP Hand Tool

Features:Large wire range coveredSimply rotate the appropriate crimp nest into positionRatchet mechanism ensures complete crimp cycleEasy access ratchet release

Generally used in Battery Lead applicationsImage representative of type only

Part Number Description mm² (AWG) or other601075 Tool without Ratchet for Battery Terminals & Lugs 10.0 - 50.0 (8-1/0)601075-1 Tool with Ratchet for Battery Terminals & Lugs (pictured) 10.0 - 50.0 (8-1/0)



Hydraulic Hand Tool - SOLISTRAND

Features:Integral Dies, simply rotate the appropriate die into positionPump action die closure

Generally used in Military & Aerospace applicationsImage representative of type only

Part Number Description mm² (AWG) or other59975-1 SOLISTRAND Terminals & Splices 10.0 - 35.0 (8-2)


Hydraulic Head - SOLISTRAND

Features:Integral Dies, simply rotate the appropriate die into positionUse with:Optional Hose Assemblies; 1583662-1, 1583662-2 or 1583662-3Respectively; 1.83 M (6'), 3 M (10'), 6.1 M (20')Hand Pump 1583661-1Foot Pump 1583659-1Electric-Hydraulic Pumps; 439798-2, 523199-1

A version of 59975-1 for use with powered optionsImage representative of type only

Part Number Description mm² (AWG) or other1673672-1 Complete Head for SOLISTRAND Terminals & Splices 10.0 - 35.0 (8-2)



Battery-Hydraulic Tool 100 KN

Features:Fast battery re-charge in 15 minutes50 cycles approx. with one chargeRotating head for easy access

Kit Includes: (Spare part PN)Tool + HeadBattery charger (7-1579005-7)Battery (7-1579005-8)Carry Case (8-1579005-0)Foam inlay (8-1579005-1)

Option:Bench-mount 7-1579005-9

1-1579002-9 with closed head designThe listed Hex crimp Dies conform to DIN 48083Lugs to be applied should conform to DIN 46235


Part Number Description mm² (AWG) or other3-1579009-1 Die-set - Indent Crimp for Cable Lugs 10.0 (8)5-1579009-4 Die-set - Indent Crimp for Cable Lugs 120.0 (4/0)3-1579009-2 Die-set - Indent Crimp for Cable Lugs 16.0 mm²3-1579009-3 Die-set - Indent Crimp for Cable Lugs 25.0 (4)5-1579009-1 Die-set - Indent Crimp for Cable Lugs 25.0 (4)3-1579009-4 Die-set - Indent Crimp for Cable Lugs 35.0 (2)3-1579009-5 Die-set - Indent Crimp for Cable Lugs 50.0 mm²5-1579009-2 Die-set - Indent Crimp for Cable Lugs 6.0 (10)3-1579009-6 Die-set - Indent Crimp for Cable Lugs 70.0 mm²5-1579009-3 Die-set - Indent Crimp for Cable Lugs 95.0 mm²1-1579009-6 Die-set - 7mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Al 300 mm²1579009-3 Die-set - 7mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 10 mm²1-1579009-7 Die-set - 14mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 10 mm²1-1579009-0 Die-set - 7mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 120 mm²2-1579009-4 Die-set - 14mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 120 mm²1-1579009-2 Die-set - 7mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 150 mm²; Al 95-120 mm²2-1579009-5 Die-set - 14mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 150 mm²; Al 95-120 mm²1579009-4 Die-set - 7mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 16 mm²; Al 10 mm²1-1579009-8 Die-set - 14mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 16 mm²; Al 10 mm²1-1579009-3 Die-set - 7mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 185 mm²; Al 150 mm²2-1579009-6 Die-set - 14mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 185 mm²; Al 150 mm²1-1579009-4 Die-set - 7mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 240 mm²; Al 185 mm²2-1579009-7 Die-set - 14mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 240 mm²; Al 185 mm²1579009-5 Die-set - 7mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 25 mm²1-1579009-9 Die-set - 14mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 25 mm²1-1579009-5 Die-set - 7mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 300 mm²; Al 240 mm²2-1579009-8 Die-set - 14mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 300 mm²; Al 240 mm²1579009-6 Die-set - 7mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 35 mm²; Al 16-25 mm²2-1579009-0 Die-set - 14mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 35 mm²; Al 16-25 mm²1579009-7 Die-set - 7mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 50 mm²; Al 35 mm²2-1579009-1 Die-set - 14mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 50 mm²; Al 35 mm²1579009-8 Die-set - 7mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 70 mm²; Al 50 mm²2-1579009-2 Die-set - 14mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 70 mm²; Al 50 mm²1579009-9 Die-set - 7mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 95 mm²; Al 70 mm²2-1579009-3 Die-set - 14mm thick; Hex Crimp for Tubular & Cast Cable/Battery Lugs Cu 95 mm²; Al 70 mm²



Cable Cutter - Battery-Hydraulic Tool 100 KN

Features:use with1-579002-9 Battery-Hydraulic Tool 100 KN

Take the effort out of cable cutting!Image representative of type only

Part Number Description mm² (AWG) or other4-1579002-5 Cutter Head only Al & Cu

up to Ø46mm (300 mm² approx)


'U' Die Assy

Features:Die outline dimensions conform to 'U' Die Industry StandardUse in:1490748-1 'U' Die 12 Ton Hydraulic Hand Tool 1490749-1 'U' Die 14 Ton Hydraulic Hand Toolor1213875-2 Battery-Hydraulic Tool Kit - 12 Ton 'U' Dieor1490745-1 'U' Die 12 Ton Hydraulic Head 1490747-1 'U' Die 12 Ton Hydraulic Head (Titanium) 1490746-1 'U' Die 12 Ton Hydraulic Head - 1.5(Excluding Die 1583097-1)orany 12 ton (min) compatible proprietary equipment

A range of Die-sets for Heavy Duty crimpingImage representative of type only

Part Number Description mm² (AWG) or other1583092-1 AMPOWER Terminals & Splices - Complete Die-set 16.0 (6)1583093-1 AMPOWER Terminals & Splices - Complete Die-set 25.0 (4)1583094-1 AMPOWER Terminals & Splices - Complete Die-set 35.0 (2)1583095-1 AMPOWER Terminals & Splices - Complete Die-set 50.0 (1/0)1583096-1 AMPOWER Terminals & Splices - Complete Die-set 70.0 (2/0)1583097-1 AMPOWER Terminals & Splices - Complete Die-set 95.0 (3/0)1490597-1 TERMINYL Terminals & Splices - Complete Die-set

(PLASTI-GRIP where no insulation crimp is required)10.0 (8)

1490598-1 TERMINYL Terminals & Splices - Complete Die-set(PLASTI-GRIP where no insulation crimp is required)

16.0 (6)


25.0 (4)



'U' Die Assy (14 ton)

Features:Die outline dimensions conform to 'U' Die Industry StandardUse in:1490749-1 'U' Die 14 Ton Hydraulic Hand Toolor1901821-1 'U' Die 12 Ton Hydraulic Head - 1.5(Excluding Dies; 1490576-1 & 1583098-1)orany 14 ton (min) compatible proprietary equipment

A range of Die-sets for Heavy Duty crimpingImage representative of type only

Part Number Description mm² (AWG) or other1490534-1 AMPLI-BOND and PLASTI-GRIP Terminals & Splices - Complete Die-set 10.0 (8)1490535-1 AMPLI-BOND and PLASTI-GRIP Terminals & Splices - Complete Die-set 16.0 (6)1490536-1 AMPLI-BOND and PLASTI-GRIP Terminals & Splices - Complete Die-set 25.0 (4)1490410-1 AMPLI-BOND and PLASTI-GRIP Terminals & Splices - Complete Die-set 35.0 (2)1583098-1 AMPOWER Terminals & Splices - Complete Die-set 120.0 (4/0)1490556-1 COPALUM Sealed Terminals and Splices Cu 10.0 (8)

Al 16.0 (6)1490557-1 COPALUM Sealed Terminals and Splices Cu 16.0 (6)


Al 10.0 (8)1490573-1 COPALUM Terminals and Splices Cu 10.0 (8)







Al 50.0 (1/0)1490718-1 COPALUM Terminals and Splices Cu 35.0 (2)

Al 50.0 (1/0)1490572-1 COPALUM Terminals and Splices Cu 8.0 (10)


Al 10.0 (8)1490406-1 TERMINYL Terminals & Splices - Complete Die-set

(PLASTI-GRIP where no insulation crimp is required)35.0 (2)


50.0 (1/0)



'U' Die Nest

Features:Nest outline dimensions conform to 'U' Die Industry StandardUse in:1490748-1 'U' Die 12 Ton Hydraulic Hand Tool 1490749-1'U' Die 14 Ton Hydraulic Hand Toolor1213875-2 Battery-Hydraulic Tool Kit - 12 Ton 'U' Dieor1901820-1 'U' Die 12 Ton Hydraulic Head 1490747-1 'U' Die 12 Ton Hydraulic Head (Titanium) 1901821-1'U' Die 12 Ton Hydraulic Head - 1.5 orany 12 ton (min) compatible proprietary equipment

A range of Die Nests for heavy duty crimpingImage representative of type only

Part Number Description mm² (AWG) or other1752680-8 SOLISTRAND Flag Terminals - use with Indenter 1752681-2 10.0 (8)1752680-1 SOLISTRAND Flag Terminals - use with Indenter 1752681-1 120.0 (4/0)1752680-7 SOLISTRAND Flag Terminals - use with Indenter 1752681-3 16.0 (6)1752680-6 SOLISTRAND Flag Terminals - use with Indenter 1752681-3 25.0 (4)1752680-5 SOLISTRAND Flag Terminals - use with Indenter 1752681-3 35.0 (2)1752680-4 SOLISTRAND Flag Terminals - use with Indenter 1752681-1 50.0 (1/0)1752680-3 SOLISTRAND Flag Terminals - use with Indenter 1752681-1 70.0 (2/0)1752680-2 SOLISTRAND Flag Terminals - use with Indenter 1752681-1 95.0 (3/0)1490413-9 SOLISTRAND Heavy Duty Terminals & Splices - use with Indenter 1490414-2 10.0 (8) HD1-1490413-0 SOLISTRAND Heavy Duty Terminals & Splices - use with Indenter 1490414-2 16.0 (6) HD1-1490413-1 SOLISTRAND Heavy Duty Terminals & Splices - use with Indenter 1490414-2 25.0 (4) HD1-1490413-2 SOLISTRAND Heavy Duty Terminals & Splices - use with Indenter 1490414-3 35.0 (2) HD1-1490413-3 SOLISTRAND Heavy Duty Terminals & Splices - use with Indenter 1490414-3 50.0 (1/0) HD1490413-1 SOLISTRAND Terminals & Splices - use with Indenter 1490414-1 10.0 (8)1490413-8 SOLISTRAND Terminals & Splices - use with Indenter 1490414-3 120.0 (4/0)1490413-2 SOLISTRAND Terminals & Splices - use with Indenter 1490414-2 16.0 (6)1490413-3 SOLISTRAND Terminals & Splices - use with Indenter 1490414-2 25.0 (4)1490413-4 SOLISTRAND Terminals & Splices - use with Indenter 1490414-2 35.0 (2)1490413-5 SOLISTRAND Terminals & Splices - use with Indenter 1490414-3 50.0 (1/0)1490413-6 SOLISTRAND Terminals & Splices - use with Indenter 1490414-3 70.0 (2/0)1490413-7 SOLISTRAND Terminals & Splices - use with Indenter 1490414-3 95.0 (3/0)



'U' Die Indenter

Features:Indenter outline dimensions conform to 'U' Die Industry StandardUse in:1490748-1 'U' Die 12 Ton Hydraulic Hand Tool 1490749-1'U' Die 14 Ton Hydraulic Hand Toolor1213875-2 Battery-Hydraulic Tool Kit - 12 Ton 'U' Dieor1901820-1 'U' Die 12 Ton Hydraulic Head 1490747-1 'U' Die 12 Ton Hydraulic Head (Titanium) 1901821-1'U' Die 12 Ton Hydraulic Head - 1.5 orany 12 ton (min) compatible proprietary equipment

A range of Indenters for Heavy Duty crimpingImage representative of type only

Part Number Description mm² (AWG) or other1752681-2 SOLISTRAND Flag Terminals - use with nest 1752680-8 10.0 (8)1752681-3 SOLISTRAND Flag Terminals - use with nests; 1752680-5, 1752680-6, 1752680-7 16.0 - 35.0 (6-2)1752681-1 SOLISTRAND Flag Terminals - use with nests; 1752680-1, 1752680-2, 1752680-3,

1752680-450.0 - 120.0 (1/0-4/0)

1490414-1 SOLISTRAND Terminals & Splices - use with Nest 1490413-1 10.0 (8)1490414-2 SOLISTRAND Terminals & Splices - use with Nests; 1490413-2, 1490413-3,

1490413-416.0 - 35.0 (6-2)

1490414-3 SOLISTRAND Terminals & Splices - use with Nests; 1490413-5, 1490413-6, 1490413-7, 1490413-8

50.0 - 120.0 (1/0-4/0)


'U' Die 12 Ton Hydraulic Hand Tool

Features:36.5mm (1.2") stroke for faster crimpingPump action die closureCirca 20,000 cycles

Suitable for ALL 'U' Dies - with the exception of 'U' Die Assy (14 ton)Image representative of type only

Part Number Description mm² (AWG) or other1490748-1 Tool without Die-set (U Die alternative to 59974-1) 12 Ton U Dies only



'U' Die 14 Ton Hydraulic Hand Tool

Features:38mm (1.5") strokePump action die closureCirca 20,000 cycles

Suitable for ALL 'U' DiesImage representative of type only

Part Number Description mm² (AWG) or other1490749-1 Tool without Die-set (U Die alternative to 59973-1) Any U Die


'U' Die 12 Ton Hydraulic Head

Features:36.5mm (1.2") stroke for fast cycleRated for use with 700 bar (10,000 psi) pump unitsCirca 20,000 cycles

Use with:Optional Hose Assemblies; 1583662-1, 1583662-2 or 1583662-3Respectively; 1.83 M (6'), 3 M (10'), 6.1 M (20')Hand Pump 1583661-1Foot Pump 1583659-1Electric-Hydraulic Pumps; 439798-2, 523199-1


Part Number Description mm² (AWG) or other1490745-1 Head without dies 25.4mm (1") stroke (U Die alternnative to 69051)1490747-1 Lightweight Titanium Head without dies (U Die alternnative to 69051) 12 Ton U Dies only


Battery-Hydraulic Tool Kit - 12 Ton 'U' Die

Features:Rotating Head 320°Excellent power to weight ratioCirca 10,000 Cycles

Kit Includes:Crimp ToolBattery Charger 220v (PN 1213873-2)Rechargeable Battery (PN 1213872-1)Carry Case with strap


Part Number Description mm² (AWG) or other1213875-2 Complete Kit with EU Power Plug 12 Ton U Dies only



'U' Die 14 Ton Hydraulic Head

Features:38mm (1.5") StrokeRated for use with 700 bar (10,000 psi) pump unitsRated for 20,000 cycles



Part Number Description mm² (AWG) or other1490746-1 Head without dies 38mm (1.5") stroke (U Die alternnative to 69051) Any U Die


'U' Die 14 Ton Hydraulic Head - Latched

Features:Latched Head for added strength38mm (1.5") StrokeRated for use with 700 bar (10,000 psi) pump units



Part Number Description mm² (AWG) or other1976230-1 Head (Latched) without Dies Any U Die



Dies for Battery Tool Kit - 4 Ton Latch Head

Features:Use in:1901343-2 Battery Tool Kit with retract switch (EU power plug)1901343-4 Battery Tool Kit without retract switch (EU power plug)


Part Number Description mm² (AWG) or other1976977-1 Die-set for PIDG STRATO-THERM Terminals & Splices with PTFE or PEEK thin-wall

Insulation4.0 (12)

1976976-1 Die-set for PIDG STRATO-THERM Terminals & Splices with PTFE or PEEK thin-wall Insulation

6 (10.0)

1901001-1 Die-Nest for SOLISTRAND Terminals & Splices - use with Indenter 1901002-2 10.0 (8)1901002-2 Die-Indenter for SOLISTRAND Terminals & Splices - use with Nest 1901001-1 10.0 (8)1901002-1 Die-Indenter for SOLISTRAND Terminals & Splices - use with Nest's; 1901000-1,

1901000-2, 1901000-316.0 - 35 (6-2)

1901000-1 Die-Nest for SOLISTRAND Terminals & Splices - use with Indenter 1901002-1 16.0 (6)1901000-2 Die-Nest for SOLISTRAND Terminals & Splices - use with Indenter 1901002-1 25.0 (4)1901000-3 Die-Nest for SOLISTRAND Terminals & Splices - use with Indenter 1901002-1 35.0 (2)1901006-1 Die-set for TERMINYL Terminals & Splices;

(PLASTI-GRIP where no insulation crimp is required)10.0 (8) Red

1901007-1 Die-set for TERMINYL Terminals & Splices;(PLASTI-GRIP where no insulation crimp is required)

16.0 (6) Blue


Battery Tool Kit - 4 Ton Latch Head

Features:Over 80 crimps per chargeCompact - only 356mm (14") long and weighs 1.6 kg (3.5lbs)

The Tool Kit is supplied in a durable plastic Carry Case and includes:Battery Tool with Latched HeadBattery Charger 220vTwo Batteries

SparesBattery Charger 220v (PN 1725840-2) EU power plugRechargeable Battery (PN 1725839-1)

Ideal for low to medium production volumesImage representative of type only

Part Number Description mm² (AWG) or other1901343-2 Battery Tool Kit - 4 Ton Latch Head with retract switch (EU power plug)1901343-4 Battery Tool Kit - 4 Ton Latch Head without retract switch (EU power plug)



Die-set - Hydraulic Head Open (Shank Die)

Features:Can be used with

Head 1752868-1 - 700 bar (10,000 psi)orHead 69099 - 580 bar (8,200 psi)


Part Number Description mm² (AWG) or other68044 COPALUM Terminals and Splices Cu 10.0 (8)

Al 16.0 (6)68085 COPALUM Terminals and Splices Cu 10.0 (8)






Al 50.0 (1/0)68131 COPALUM Terminals and Splices Cu 35.0 (2)

Al 50.0 (1/0)68048 COPALUM Terminals and Splices Cu 50.0 (1/0)




Al 95.0 (3/0)68043 COPALUM Terminals and Splices Cu 8.0 (10)


Al 10.0 (8)318106-1 COPALUM Terminals and Splices Cu 95.0 (3/0)

Al 120.0 (4/0)69216 SOLISTRAND Terminals & Splices 10.0 (8)45445 SOLISTRAND Terminals & Splices 120.0 (4/0)69217 SOLISTRAND Terminals & Splices 16.0 (6)69218 SOLISTRAND Terminals & Splices 25.0 (4)45433 SOLISTRAND Terminals & Splices 35.0 (2)45436 SOLISTRAND Terminals & Splices 50.0 (1/0)45439 SOLISTRAND Terminals & Splices 70.0 (2/0)45442 SOLISTRAND Terminals & Splices 95.0 (3/0)69211-1 STRATO-THERM Post Insulated Terminals & Splices 10.0 (8)69212-1 STRATO-THERM Post Insulated Terminals & Splices 16.0 (6)69213-1 STRATO-THERM Post Insulated Terminals & Splices 25.0 (4)69214-1 STRATO-THERM Post Insulated Terminals & Splices 35.0 (2)69215-1 STRATO-THERM Post Insulated Terminals & Splices 50.0 (1/0)69254-1 STRATO-THERM Post Insulated Terminals & Splices 70.0 (2/0)



Hydraulic Head Open (Shank Die)

Features:Rated for use with 700 bar (10,000 psi) pump units

Use with:Optional Hose Assemblies; 1583662-1, 1583662-2 or 1583662-3Respectively; 1.83 M (6'), 3 M (10'), 6.1 M (20')

Hand Pump 1583661-1Foot Pump 523199-2Electric-Hydraulic Pumps; 439798-2, 523199-1


Part Number Description mm² (AWG) or other1752868-1 Hydraulic Head without Die-set (700 bar equivalent of 69099)


Hydraulic Head Open - Dyna-Crimp


Use with:Optional Hose Assemblies; 59909-7, 1-59909-5 or 2-59909-1Respectively; 2.12 M (7'), 4.58 M (15') 6.4 M (21')

Hand Pump 314979-1Foot Pump 523199-3Electric-Hydraulic Pump; 439798-1


Part Number Description mm² (AWG) or other69099 Hydraulic Head without Die-Set



Die-set - Hydraulic Head Closed (Shank Die)

Features:Use in Heads:1752787-1 & 1752877-1 - 700 bar (10,000 psi)orDynacrimp Heads: 58422-1 & 69066 - 580 bar (8,200 psi)

Dies listed with * can only be used in Heads: 1752787-1 & 58422-1 see also relevant Die Instruction Sheet for more details


Part Number Description mm² (AWG) or other48860-1 AMPLI-BOND and PLASTI-GRIP Terminals and Splices 25.0 (4)48861-1 AMPLI-BOND and PLASTI-GRIP Terminals & Splices 35.0 (2)314948-1 * COPALUM Sealed Terminals and Splices 120.0 (4/0)68007 COPALUM Sealed Terminals and Splices Cu 10.0 (8)

Al 16.0 (6)68008 COPALUM Sealed Terminals and Splices Cu 16.0 (6)

Al 25.0 (4)68009 COPALUM Sealed Terminals and Splices Cu 25.0 (4)


Al 50.0 (1/0)68011-1 * COPALUM Sealed Terminals and Splices Cu 50.0 (1/0)

Al 70.0 (2/0)314964-1 COPALUM Sealed Terminals and Splices Cu 50.0 (1/0)

Al 70.0 (2/0)59877-1 * COPALUM Sealed Terminals and Splices Cu 70.0 (2/0)

Al 95.0 (3/0)68006 COPALUM Sealed Terminals and Splices Cu 8.0 (10)

Al 10.0 (8)47824 TERMINYL Terminals & Splices

(PLASTI-GRIP where no insulation crimp is required)50.0 (1/0)

47825 TERMINYL Terminals & Splices(PLASTI-GRIP where no insulation crimp is required)

70.0 (2/0)


Hydraulic Head Closed (Shank Die)





Part Number Description mm² (AWG) or other1752787-1 Hydraulic Head without Die-set (700 bar equivalent of 58422-1)1752877-1 Hydraulic Head without Die-set (700 bar equivalent of 69066) - lighter than 1752787-1



Hydraulic Head Closed - Dyna-Crimp





Part Number Description mm² (AWG) or other58422-1 Head without dies69066 Head without dies - lighter than 58422-1


Die-set - Hydraulic Head Open (Shank Die H'Duty)


Head 1752786-1 - 700 bar (10,000 psi)orHead 69082 - 580 bar (8,200 psi)


Part Number Description mm² (AWG) or other46760-2 AMPOWER Terminals & Splices 1,000 MCM HD69653 AMPOWER Terminals and Splices 350 MCM46754-2 AMPOWER Terminals & Splices 400 MCM46755-2 AMPOWER Terminals & Splices 500 MCM46756-2 AMPOWER Terminals & Splices 600 MCM59870-1 AMPOWER Terminals and Splices 600 MCM HD46757-2 AMPOWER Terminals & Splices 700 MCM46758-2 AMPOWER Terminals & Splices 800 MCM46759-2 AMPOWER Terminals & Splices 900 MCM68034 COPALUM Terminals and Splices Cu 120.0 (4/0)

Al 250 MCM68035 COPALUM Terminals and Splices Cu 250 MCM



Al 500 MCM68050 COPALUM Terminals and Splices Cu 95.0 (3/0)


Al 120.0 (4/0)69911 SOLISTRAND Terminals & Splices 250 - 300 MCM69912 SOLISTRAND Terminals & Splices 300 - 350 MCM69913 SOLISTRAND Terminals & Splices 400 MCM69914 SOLISTRAND Terminals & Splices 500 - 600 MCM



Hydraulic Head Open (Shank Die Heavy Duty)





Part Number Description mm² (AWG) or other1752786-1 Hydraulic Head without Die-set (700 bar equivalent of 69082)


Hydraulic Head Open (Heavy Duty) - Dyna-Crimp





Part Number Description mm² (AWG) or other69082 Head without dies



Die-set - Hydraulic Head Closed (Shank Die H'Duty)


Head 1752788-1 - 700 bar (10,000 psi)orHead 58445-1 - 580 bar (8,200 psi)


Part Number Description mm² (AWG) or other48816 SOLISTRAND Terminals & Splices 250 - 300 MCM48817 SOLISTRAND Terminals & Splices 300 - 350 MCM48818 SOLISTRAND Terminals & Splices 400 MCM48819 SOLISTRAND Terminals & Splices 500 - 600 MCM


Hydraulic Head Closed (Shank Die Heavy Duty)





Part Number Description mm² (AWG) or other1752788-1 Heavy Duty Hydraulic Head without Die-set (700 bar equivalent of 58445-1)



Hydraulic Head Closed (Heavy duty) - Dyna-Crimp





Part Number Description mm² (AWG) or other58445-1 Head without dies


Heavy duty Electric Hydraulic Pump

Features:Built for continuous useTank capacity = 11.37 liters (2.5 gallons)Weight = 25 kg (65 Lbs)90-95 dBA

Accessories - see 409-10081


Part Number Description mm² (AWG) or other169120-2 Heavy duty Electric Hydraulic Pump - 580 Bar (8,200 psi) 220v1804700-2 Heavy duty Electric Hydraulic Pump - 700 Bar (10,000 psi) 220v


Electric Hydraulic Pump, light duty

Features:Lightweight and compact design 10 kgLarge Carry-handle for easy portabilityTwo speed cycle reduces cycle time for improved productivity24 v DC remote motor control, 3m length for operator safetyStarts under full loadHigh strength moulded shroudSupplied with male quick coupler (no hose supplied)

Pressure Gauge options:523200-1 Pressure Gauge523200-2 Digital Pressure Gauge523200-3 1/4" Adapter (required when using either Gauge)


Part Number Description mm² (AWG) or other523199-1 Portable pump 700 bar (10,000 psi) suitable for intermittent duty cycle



Hydraulic Hand Pump

Features:This pump action unit allows hyraulic heads via optional length hydraulic hoses a degree of positional flexibilty


Part Number Description mm² (AWG) or other1583661-1 Hand Pump 700 bar (10,000 psi)


Hydraulic Foot Pump

Features:Pump action operationClicker valve pressure regulationSupplied with male quick-coupling

580 (8,500 psi) & 700 bar (10,000 psi) optionsImage representative of type only

Part Number Description mm² (AWG) or other523199-2 Max pressure rating 700 bar (10,000 psi)523199-3 Max pressure rating 580 bar (8,500 psi)


Group Cutter

Features:Suitable for Copper or Aluminum, solid or stranded to 35 mm² (2 awg) and Coax to RG 9Steel handles lock together for safe storageNon-slip plastic handle gripsNot for Steel or ACSR cable

1490498-1Image representative of type only


Cable Cutter 350 mcm

Features:Suitable for Copper or Aluminum, solid or strandedto 185 mm² (350 MCM)Steel HandlesNon-slip plastic handle gripsNot for Steel or ACSR cable


Cable Cutter 500 mcm

Features:Suitable for Copper or Aluminum, solid or strandedto 300 mm² (500 MCM)Fibreglass HandlesNon-slip plastic handle gripsNot for Steel or ACSR cableto


Cable Cutter 350 mcm with Ratchet

Features:Suitable for Copper or Aluminum, solid or strandedto 180 mm² (350 MCM)Handles lock together for safe storageRatchet mechanism keeps handle force lowNon-slip plastic handle gripsNot for Steel or ACSR cable



Cable Cutter 500 mcm with Ratchet

Features:Suitable for Copper or Aluminum, solid or strandedto 300 mm² (500 MCM)Fibreglass HandlesNon-slip plastic handle gripsNot for Steel or ACSR cable


Cable Cutters SH Range

Features:Very compact and lightweightOne handed - low handle closing forceBurr free cuttingLockable cutting strokeNon-slip plastic hand grips

A range of heavy duty Cable Cutting toolsImage representative of type only

Part Number Description mm² (AWG) or other734045-1 solid and stranded copper and aluminium cables Solid Cu 185 mm²

Solid Al 185 mm²Stranded Cu / Al Ø52Hi Flex Cu Ø52

169415-1 Solid and stranded copper and aluminium cables Solid Cu 185 mm²Solid Al 240 mm²Stranded Cu / Al Ø25Hi Flex Cu Ø32

1-1579002-8 solid and stranded copper and aluminium cables (no ASCR) Solid Cu 480 mm²Solid Al 480 mm²Stranded Cu / Al Ø54


Contractor Tools Revised: January 2010

Corex Coax Stripper

Features:Complete cable stripEasy cutter adjustmentSimple rotary cutting motionColour coded cassettesPre-set strip lengths

For Cables with a Jacket diameter of 2.54 to 7.62 mmImage representative of type only

Part Number Description mm² (AWG) or other603995-2 2 step cable stripper for Comercial BNC connectors and RG 58 / 59 / 62 cable.

6.8 mm outer jacket strip length.Spare Cassete Blue, PN 603996-2

RG 58 / 59 / 62Cable Ø5.0-6.5mm

947489-1 3 step cable stripper for Commercial BNC connectors.7.5 mm outer jacket & 3.5 mm dialectric strip lengths.Spare Cassete Brown PN 947490-1

RG 58 / 59 / 62Cable Ø5.0-6.5mm

603995-5 3 step cable stripper for Dual Crimp BNC connectors.5.5 mm outer jacket & 5.5 mm dialectric strip lengthsSpare Cassete Black PN 603996-4

603995-6 3 step cable stripper for Dual Crimp Commercial BNC connectors and RG; 174, 179, 188 & 316 cable.6.8 mm outer jacket & 2.5 mm dialectric strip lengths.Spare Cassete White PN 603996-5

RG; 174, 179, 188 & 316Cable Ø2.5-3.0mm

603995-1 2 step cable stripper for Single crimp BNC connectors and RG 195 / 180 cable.6 mm outer jacket strip length.Spare Cassete Red, PN 603996-1

RG 195 / 180Cable Ø3.0-5.0mm

603995-3 2 step cable stripper for UHF connectors and RG 6 & Beldon 8281.12 mm outer jacket strip length.Spare Cassete Yellow, PN 603996-3

RG 6 & Beldon 8281Cable Ø6.4-7.0mm


Coax Cable Stripper

Features:3 Blades designed to strip RG 6, 58 and 59 cable in one stepReplaceable Blade Cartridges



Oden - Cable Stripper

Features:Outer Sheath Stripper suitable for most discrete, multicore and fibre optic cablesFine adjustment is possible by a 10 position adjustment wheelReplaceable BladeAutomatically adjusts to different cable diametersWorks on cable diameters up to 11mmIdeal for Cat 5 & 6 cable

2-1579002-4 - Stripping Tool7-1579005-4 - Spare Blade Image representative of type only

Cyclops - Cable Stripper

Features:Outer Sheath StripperAutomatically adjusts to different cable diametersWorks on cable diameters up to 11mm


Economy Wire Stripper & Cutter

Features:Strips 0.2 - 6.0 mm² (24-10)8 wire size adjustments



Tor - Rotary Cable Stripper

Features:Works on cables from 4.5 to 40 mm diameterCircular + Straight StripCircular + Spiral StripAlso window stripping possibleReplaceable bladeLanyard fixingSpare blade in handle cavity

2-1579002-5 - Stripping ToolNato Stk No. 5110-99-5301839

7-1579005-5 - Spare Blade


Rotary Cable Stripper

Features:Works on cables up to 25 mm diameterCircular + Straight StripSupplied with spare blade



Embla - Automatic Wire Stripper

Features:Easily replaceable blade cassetteV blade cassettes for difficult cable typesAdjustable stripping lengthErgonomic non-slip handlesBuilt-in cutter, also with replaceable blades

For various insulation typesImage representative of type only

Part Number Description mm² (AWG) or other2-1579002-3 most insulation types and includes:

form blade Cassette 4 - 16 mm²Spare Blade 7-1579005-3

4.0 - 16.0 (12-6)

2-1579002-2 PTFE, THHN & TTHW and includes:V blade Cassette 0.02 - 4 mm²Spare Blade 7-1579005-2

0.2 - 4.0 (24-12)

2-1579002-1 Standard PVC and includes:parallel blade Cassette 0.02 - 10 mm²Nato Stk No. 5110-99-7009177Spare Blade 7-1579005-1

0.02 - 10.0 (34-8)


Automatic Wire Stripper

Features:Works on PVC, THHN and THHW cable 0.08 - 6.0 (28-10)Adjustable stripping lengthErgonomic non-slip handlesBuilt-in cutter



Die-cast Automatic Wire Stripper

Features:Adjustable strip lengthAutomatic cut-depthNon-slip handles


Part Number Description mm² (AWG) or other1579002-2 Base Tool without Blades1-1579002-2 for PVC, THHN and THHW cable (includes blades)

Spare Blade set 3-1579005-70.08 - 6.0 (28-10)

4-1579002-2 for SOLARLOK Cable (includes blades)Spare Blade set 1579006-7

1.5 - 6.0 (16-10)


Small Wire Cutters

Features:Cuts wire flushSpring loaded handles

1116571-1Used primarily when lacing / installing the tool-less Mod Jack Image representative of type only

KT 80 Cutting Tool

Features:Up to 64 conductors of 0.5mm² by 81.5mm wideClean undistorted cutBuilt-in Guide ensures square cut

Replaceable:Blade 658654-1Anvil 658563-1

654061-1 - Ideal for cutting Ribbon CableImage representative of type only


Cable Tie Gun

Features:Automatic cut-offAdjustable tension setting

734587-1 - for Cable Ties 2.2 - 4.8 mm and thickness up to 1.6 mmImage representative of type only

Non-impact Punch-down Tool

Features:Rubber palm gripBlade Storage area in the side of the ToolAccepts all Twist & Lock Blades

Tools without impact assistImage representative of type only

Part Number Description mm² (AWG) or other1583236-1 Tool with 110 Blade 0.08 - 0.34 (28-24)1583236-2 Tool without blade 0.08 - 0.34 (28-24)1583236-3 Tool with 066 Blade 0.08 - 0.34 (28-24)


Impact Punch-down Tool

Features:Rubber palm gripSpare blade storageAdjustable Hi / Low impact settingAccepts all standard twist & Lock blades

Tools with impact assistImage representative of type only

Part Number Description mm² (AWG) or other1583608-1 Tool with 110 Blade 0.08 - 0.34 (28-24)1583608-2 Tool without Blade 0.08 - 0.34 (28-24)1583608-3 Tool with 066 Blade 0.08 - 0.34 (28-24)



Premium Impact Punch-down Tool

Features:Integral spot lightNon-slip cushioned gripPick hook and spudgerSpare blade storageAdjustable impact forceAccepts all standard twist & Lock blades

Tools with impact assistImage representative of type only

Part Number Description mm² (AWG) or other1375308-1 Tool with 110 Blade

1375309-1 Spare 110 Blade0.08 - 0.34 (28-24)

1375308-2 Tool without Blade 0.08 - 0.34 (28-24)1375308-3 Tool with 066 Blade

1725872-1 Spare 066 Blade0.08 - 0.34 (28-24)

1375308-4 Tool with 066 / 110 Blade1375310-1 Spare 066 / 110 Blade

0.08 - 0.34 (28-24)



Professional Hand Tool

Features:Interchangeable Dies for all but 10 posn. plugsTerminates both strain reliefs and inserts contacts in one motionRatchet mechanism ensures complete crimp cycleCuts, strips and terminatesCompatible with many other leading brand productsAMP plugs are UL approved when terminated using this tool


Part Number Description mm² (AWG) or other2-231652-8 Complete tool for MODULAR PLUG connectors 4 & 6 Posn Line853400-8 Die-set for MODULAR PLUG connectors

Use in Hand Tool Frame 2-231652 or Economy Tool 1490496-14 & 6 Posn Line

2-231652-3 Complete tool for MODULAR PLUG connectors 4 Posn Hand-set853400-3 Die-set for MODULAR PLUG connectors

Use in Hand Tool Frame 2-231652 or Economy Tool 1490496-14 Posn Hand-set

2-231652-6 Complete tool for MODULAR PLUG connectors 6 Position off-setFlat, Oval & Round - Solid & Stranded

2-231652-7 Complete tool for MODULAR PLUG connectors 6 posn Long BodyFlat, Oval & Round - Solid & Stranded

853400-7 Die-set for MODULAR PLUG connectors - Flat oval & Round - Solid or StrandedUse in Hand Tool Frame 2-231652 or Economy Tool 1490496-1

6 Posn Long BodyFlat, Oval & Round - Solid or Stranded

853400-6 Die-set for MODULAR PLUG connectors - Flat oval & Round - Solid or StrandedUse in Hand Tool Frame 2-231652 or Economy Tool 1490496-1

6 Posn off-setFlat, Oval & Round - Solid or Stranded

3-231652-0 Complete tool for MODULAR PLUG connectors 8 Posn High PerformanceCAT 5 Cable

1-853400-0 Die-set for MODULAR PLUG connectors - CAT 5 cableUse in Hand Tool Frame 2-231652 or Economy Tool 1490496-1

8 Posn High PerformanceCAT 5 cable

2-231652-1 Complete tool for MODULAR PLUG connectors 8 Posn Long Body853400-1 Die-set for MODULAR PLUG connectors

Use in Hand Tool Frame 2-231652 or Economy Tool 1490496-18 Posn Long Body



Mod Jack Tool

Features:Buit-in cable stripperTerminates and cuts all conductors in one goVery small breakouts can be achievedComes in a convenient Draw-string Pouch

Can be used on CAT 3 , 5 & 6 cable with:Rear cable entry 110 SL Series JacksRear cable entry AMP TWIST 6S SL Jacks

Tool & Lacing Fixture combinations for rear entry cable Jacks.Image representative of type only

Part Number Description mm² (AWG) or other1673956-1 Lacing Fixture for rear cable entry 110 SL series Jacks. Use in Base Tool & Pouch

1725150-30.2 (24) stranded0.2-0.4 (24-22) solid

1725150-1 Base tool, Pouch & Lacing Fixture 1673956-1 for rear cable entry 110 SL series Jacks 0.2 (24) stranded0.2-0.4 (24-22) solid

1725150-3 Base tool & Pouch for rear cable entry AMP TWIST 6S SL series Jacks.NO Lacing Fixture required

0.2 (24) stranded0.2-0.4 (24-22) solid


Crimping Kit for Modular Plugs

Features:2-231652 Proffesional hand Tool231662-1 Blade Replacement KitScrew DriverRhobust plastic Carry CaseDies for specified Plug types


Part Number Description mm² (AWG) or other1-231666-0 Standard Kit for Shielded & Non-shielded Plugs 4, 6 & 8 Posn. Line1-231666-3 Proffesional Kit for Shielded & Non-shielded Plugs 4, 6 & 8 Posn. Line

6 Posn. Long Body4 Posn. Telephone Plug

1-231666-1 Standard Kit for Shielded & Non-shielded Plugs 4-6, 8 Posn.4 Posn. Handset



Tone Generator

Features:Three built-in tonesAuto offSeparate talk battery for increased voltage and power for test setsModular Jack allows multiple cord sets to be used for different applications

1490531-11673606-1 - includes 1490531-1 plus Tone Tracer 1490533-1 in handy Two Pocket Pouch


Tone Tracer

Features:Detection without direct cable or wire contactErgonomically shapedCan be used with any Tone GeneratorReplacement quick change tips available

1490533-11673606-1 - includudes 1490533-1 plus Tone Generator 1490531-1 in handy Two Pocket Pouch


4-Pair Tester

Features:Tests for opens, shorts, mis-wires, reversals and split pairsAuto on/offBattery low indicator



Butt Set

Features:LCD Display shows; on-hook voltage, number dialled, off-hook current, called ID, stored numbers etc.Tone and pulse diallingModular cord set attachmentAuto off


SUPER CHAMP II

Features:Made from high quality special steel for long lifeFitted with plastic comfort handles

Tools for service & repairImage representative of type only

Part Number Description mm² (AWG) or other169111-1 Open Barrel Terminals 'F' crimp

Crimp widths; 2.2, 2.4, 2.8, 3.2, 3.8 & 4.8mmWire strippers for 0.5-0.75, 1.0, 1.5, 2.5, 4 & 6mm

0.4 - 6.0 (22-10)

169060-8 PIDG, PLASTI-GRIP - All TypesBolt cutters for 3, 3.5, 4 & 5mm boltsWire strippers for 0.5-0.75, 1.0, 1.5, 2.5, 4 & 6mm

0.26 - 6.6 (24-10)


SUPER CHAMP FT

Features:Made from high quality special steel for long lifeFitted with plastic comfort handles

Bulkhead Series Terminals0.3 mm²0.5 - 0.85 mm²1.25 - 2.0 mm²

PIDG & PLASTIGRIPRBY 0.5 - 6mm² (22-10)General wire strippers

720781-3 - for service & repair with Bulkhead Series and PIDG & PLASTIGRIP Terminals Image representative of type only


CRIMPAC CG

Features:Toggle lever handle force adjuster with quick releaseCable cutting device 0.5 - 6 mm² (21-10)Wire stripping device 0.5 - 6 mm² (21-10)

734372-1 - Base Tool without diesImage representative of type only

Part Number Description mm² (AWG) or other825582-2 Complete tool for CI-2; MATE-N-LOK 3.5; Standard TIMER

AMLIVERSAL Logo0.5 - 5.3 (22-10)

825582 Complete tool for CI-2; MATE-N-LOK 3.5; Standard TIMER 0.5 - 5.3 (22-10)825508-5 Complete tool for PIDG & PLASTI-GRIP Terminals 0.5 - 6.0 (22-10)734481-1 Die-set for PIDG, PLASTI-GRIP - All Types

Use in Hand Tool Frame 734372-10.6 - 6.0 (22-10)


Die-set - SDE for Fibre Optic Connectors

Features:Use in:SDE PRO-CRIMPER III Hand Tool 354940-1SDE PEW 12 Hand Tool 9-1478240-0SDE DA Hand Tool 1213745-1SDE BATTERY TOOL (Kit) 1725837-2 for shoulder diesSDE 626 Head 679304-1 + accessoriesSDE Electric Terminator 1490076-2SDE Bench Press Adapter 1579000-8 + Press 1481004-7

SDE Dies allow Hand or Powered optionsImage representative of type only

Part Number Description mm² (AWG) or other91900-1 HTS Fibre Optic contact HD-LWL series


Fibre Cleaver - S 315

Features:Long life Ceramic Blade - over 6,000 cuts90° at <1°, and 99% at <2°Suitable for single and multimode fibresCarry case included



Fibre Cleaver - Universal

Features:For all Cut & Break applicationsCutter life: circa 40,000 cleaves


Dual Purpose Butterfly Tool

Features:Mass terminates and shears all wires in a single actionCan be fixed by screws to a benchSupplied in a carrying case

Mass termination tool for AMP CHAMP productsImage representative of type only

Part Number Description mm² (AWG) or other229378-1 Standard tool for AMP CHAMP 14, 24, 36 & 50 Posn231880-1 Standard tool for AMP CHAMP 64 Posn1424624-1 BT version for AMP CHAMP 50 Posn2-229378-5 GB version for AMP CHAMP 50 Posn


Tools for Screw-machined Contacts Revised: January 2010

AF8

Features:4/8 indent Crimp to Military standardRatchet mechanism ensures complete crimp cycle8 Position Dial select Indent Depth controlMany Turrets availableErgonomic non-slip handles

601967-1 AF8 [M22520/1-01] Crimp Tool without Turret2031846-1 WA27F (Pneumatic AF8) without Turret Image representative of type only

AF8 - Turret

Features:Data plate shows compatible Contacts and settings

Use in:601967-1 - AF8 Base Tool without Turret2031846-1 - Pneumatic AF8 (WA27F) without Turret

Accurately positions Contacts in the ToolImage representative of type only

Part Number Description mm² (AWG) or other601967-5 Universal Head UH2-5 [M22520/1-05]601967-9 Turret TH45 0.15 - 1.5 (26-16)601967-2 Turret TH1A [M22520/1-02] for ARINC contacts 0.15 - 4.0 (26-12)1-601967-2 Single Position Head TP465 [M22520/1-11] for M39029 2.5 - 4.0 (14-12)601967-4 Turret TH4 [M22520/1-03] for MS17803; MS21097; OSI2814 contacts 0.15 - 1.5 (26-16)601967-7 Turret TP85 [M22520/1-07] for MS18232; MS18233 contacts RG178/U; RG196/U601967-3 Turret TH163 [M22520/1-04] for MS27490; MS27655 0.2 - 4.0 (24-12)601967-8 Turret TH199S [M22520/1-08] for MS3343; MS90460; MS90461 contacts 0.14 - 4.0 (26-12)1-601967-6 Turret TH502 for Multimate TYPE II Size 16 Pin Contacts 0.03 - 2.5 (32-14)1-601967-5 Turret TH501 for Multimate TYPE II Size 16 Socket Contact 0.03 - 2.5 (32-14)601967-6 Turret TP45 [M22520/1-06] for OSI2814 type M size 16 & 22 0.14 - 1.5 (26-16)1-601967-1 Turret TH128 for Type II contacts 2.5 - 4.0 (14-12)



AFM8

Features:4/8 indent Crimp to Military standardRatchet mechanism ensures complete crimp cycle8 Position Dial select Indent Depth controlMany Positioners availableErgonomic non-slip handles

601966-1 AFM8 [M22520/2-01] Crimp Tool without Positioner2031845-1 WA22 (Pneumatic AFM8) without Positioner Image representative of type only

AFM8 - Positioner

Features:Data plate shows compatible Contacts and settings

Use in:601966-1 [AFM8] - Base Tool without Positioner2031845-1 [WA22] - Pneumatic version without Positioner

Accurately positions Contacts in the ToolImage representative of type only

Part Number Description mm² (AWG) or other1-601966-0 Positioner K3282-601966-8 Positioner K370 for ARINC 404 COAXICON RG316/U; 188/U

RG179/URG178/U; 196/U

601966-8 Positioner K267 [M22520/2-23] for ARINC 404 Contacts 0.12 - 0.4 (26-22)601966-7 Positioner K370 [M22520/2-12] for ARINC COAXICON size 15 contacts RG178; RG179; RG188;

RG196; RG3161-601966-6 Positoiner K345 for ARINC COAXICON size 5 contacts .141Semi rigid; RG58C;

RG180B; RG188; RG2232-601966-6 Positioner K397 for ARINC COAXICON size 7 contacts RG1881-601966-7 Positoiner K344 for ARINC COAXICON size 7 contacts RG58C; RG188601966-5 Positioner K13-1 [M225202/2-08] for ARINC size 20 Contacts 0.2 (24)601966-6 Positioner K42 [M22520/2-09] for ARINC size 22 Pin Contacts 0.4 - 0.3 (22-28)966254-1 Positioner for Coaxicon MCX Straight Plugs1-601966-5 Positoiner K287 [M22520/2-11] for M39029/1-100; 1-101; 2-105; 3-108 0.15 - 0.6 (26-20)2-601966-0 Positioner K338 [M22520/2-13] for M39029/16&18 contacts 0.03 - 0.09 (32-28)2-601966-2 Positioner K339 [M22520/2-16] for M39029/17 contacts 0.03 - 0.09 (32-28)1-601966-1 Positioner K151 [M22520/2-04] for MS18232; MS18233; MS18265; MS18266

contactsRG178/U; RG196/U

1-601966-4 Positoiner K43 [M22520/2-10] for MS27490; MS27491; MS27492; MS27493; MS27494; MS27655 contacts

0.2 - 0.6 (24-20)

1-601966-3 Positioner K40 [M22520/2-07] for MS27490; MS27655 contacts 0.08 - 0.4 (28-22)601966-3 Positioner K60S [M22520/2-03] for MS3343; MS90461 contacts 0.03 - 0.4 (32-22)601966-4 Positioner K41 [M22520/2-06] for Size 22 Socket Contacts 0.4 - 0.3 (22-28)601966-2 Positioner K1S [M22520/2-02] for TERMI-BLOCK contact. 0.6 - 0.15 (20-26)1579003-1 Positioner for TRIAD-011490038-1 Positioner K789 for Winchester 100-54020S; 100-54028S contacts 0.06 - 0.6 (30-20)



FT8

Features:4/8 indent CrimpRatchet mechanism ensures complete crimp cycle8 Position Dial select Indent Depth controlErgonomic non-slip handles

608668-1 - Base Tool without PositionerImage representative of type only

Part Number Description mm² (AWG) or other608668-2 Positioner TP731 for AMPLIMITE Size 8

Use with Hand Tool 608668-11.0 - 1.5 (18-16)


M300 BT



Part Number Description mm² (AWG) or other608651-2 Positioner TP1151 for AMPLIMITE Size 8

Use with Hand Tool 608651-12.5 - 10.0 (14-8)

608651-3 Positioner SP858 for AMPLIMITE Size 8Use in hand Tool 608651-2

6.0 - 10.0 (10-8)


M309




M310



Part Number Description mm² (AWG) or other356120-1 Positioner TP1088

Use in Hand Tool 356114-1356336-1 Positioner TP944

use with Hand tool 356114-12.5 - 10.0 (14-8)

356119-1 Positioner TP1068 for Type XII contactsUse in Hand Tool 356114-1

10.0 (8)

356337-1 Positioner TP1013 for Universal MATE-N-Lok II High Current 2mmuse with Hand tool 356114-1

2.5 - 6.0 (14-10)


M317




MH860

Features:4/8 indent Crimp to Military standard M22520/7-01Ratchet mechanism ensures complete crimp cycle8 Position Dial select Indent Depth controlMany Turrets availableErgonomic non-slip handles


Part Number Description mm² (AWG) or other2031848-1 Positioner 86-20 for M39029 Contacts

Use with hand Tool 2031850-10.2 - 0.6 (24-20)


HX4

Features:Crimp to Military standard M22520/5-01Ratchet mechanism ensures complete crimp cycleErgonomic non-slip handles


Part Number Description mm² (AWG) or other2031852-1 Die-set Y197 - M22520/5-6 Hex .178 / .213" A/F2031851-1 Die-set Y178 - M22520/5-6 Hex .429" A/F



ERGOCRIMP - Chrome

Features:Chrome plated for greater corrosion resistance.Interchangeable DiesVirtually a straight action jaw closureRatchet machanism ensures complete crimp cycleEasy access ratchet releaseHandle pressure adjustment with locking deviceErgonomic non-slip handles

The listed Dies can be used in the same options as regular ERGOCRIMP Dies

1-1105850-8 Base Tool without Die-set (pictured)

Note: This tool is not compatible with SDE DiesImage representative of type only

Part Number Description mm² (AWG) or other2-1105652-8 Die-set for HS S Contacts 10.0 & 16.0539744-2 Die-set for HTS HDM 0.2 - 0.5539668-2 Die-set for HTS HDM Contacts 0.2 - 1.51-1105652-8 Die-set for HTS HSS Contacts 6.0 & 25.01-1105851-8 Complete Tool for HTS: HE/HA; HND; HVT Contacts 0.14 - 4.01-1105852-8 Die-set for HTS: HE/HA; HND; HVT Contacts 0.14 - 4.02-1105870-8 Die-set for HTS: HSK; HSM; HSS Contacts 4.0 - 10.01-1105870-8 Die-set for HTS: HSM; HSK; HSS Contacts 0.75 - 2.5


Hydraulic Hand Tool 30 KN

Features:Lightweight Tool with rotating headPump action closure with low handle forceAdjustable strokeAutomatic release with audible "click"Manual overide trigger release

1-1105653-8 Hand tool without Die-setImage representative of type only

Part Number Description mm² (AWG) or other5-1105653-8 Die-set for HF Contacts 25.0 (4)6-1105653-8 Die-set for HF Contacts 35.0 (2)8-1105653-8 Die-set for HF Contacts 70.0 (2/0)7-1105653-8 Die-set for HF Contacts 50.0 (1/0)3-1105653-8 Die-set for HS S & HF Contacts 10.0 (8)4-1105653-8 Die-set for HS S & HF Contacts 16.0 (6)2-1105653-8 Die-set for HTS: HSS; HF Contacts 6.0 (10)



Hydraulic Hand Tool 60 KN

Features:Rotating headPump action closure with low handle forceAutomatic release with audible "click"Manual overide trigger release

1110956-1 Hand tool without Die-set supplied in plastic carry caseImage representative of type only

Part Number Description mm² (AWG) or other1110956-5 Die-set for HF Contacts 120.0 (4/0)1110956-6 Die-set for HF Contacts 150.0mm²1110956-7 Tool-set comprising; 110956-1 + 1110956-2 to -6 inclusive

for HF contacts50.0 - 150.0 (1/0-4/0)

1110956-2 Die-set for HF Contacts 50.0 (1/0)1110956-3 Die-set for HF Contacts 70.0 (2/0)1110956-4 Die-set for HF Contacts 95.0 (3/0)


Industry / Product specific kits Revised: January 2010

Ampliset repair Kit

Features:1-off Superchamp II hand toolA small quantity of 21 of the most common pre-insulated terminals and splicesPackaged in a compact plastic wallet

For more detail please see information flyer 1308204


Part Number Description mm² (AWG) or other725972 Pre-insulated Terminals & Splices 0.5 - 6.6 (22-10)


Service Kit - SUPERCHAMP II

Features:Superchamp II hand toolA small quantity of the most common pre-insulated terminals and splicesPackaged in a hard plastic snap-shut case



Part Number Description mm² (AWG) or other725922 Installation, service and repair for Electrician's 0.5 - 6.6 (22-10)725929 Service and repair for Automotive applications 0.5 - 6.6 (22-10)



Service Kit - CRIMPAC CG

Features:CRIMPAC CG hand toolTwice the quantity of terminals and splices supplied in Service Kit PN 725922Packaged in a hard plastic snap-shut case


Ideal for Service and RepairFaster crimping than Service Kit PN 725922 as the CRIMPAC AG Hand Tool crimps both wire and insulation simultaneously


Part Number Description mm² (AWG) or other725923 Installation, service and repair for Electrician's 0.5 - 6.6 (22-10)


Universal Service Tool Kit

Features:Comprises:Service Kit Tool 3-1579000-0Interchangeable Die-sets for:PIDG, PLASTIGRIP Green/YellowPIDG, PLASTIGRIP Red/BlueFASTON; FASTIN-FASTON 0.5 - 6.0 (22-10)SOLISTRAND Terminals & Splices 0.5 - 6.0 (22-10)Wire End Ferrules 0.25 - 6.0 (24-10)


Part Number Description mm² (AWG) or other1-1579010-5 Universal Service Tool Kit see relevant Die



Starter Kit

Features:A strong all purpose Carry CaseTermination Tool Kit25 JacksInstruction SheetCD-Rom with videos showing step-by-step cable termination & printable instructions


Part Number Description mm² (AWG) or other2-1579010-7 110 SL Series Shielded Jacks 0.2 (24) stranded

0.2-0.4 (24-22) solid2-1579010-6 110 SL Series Unshielded Jacks 0.2 (24) stranded

0.2-0.4 (24-22) solid2-1579010-9 AMP TWIST Jacks 0.2 (24) stranded

0.2-0.4 (24-22) solid2-1579010-8 Cat5e SL Jacks 0.2 (24) stranded

0.2-0.4 (24-22) solidOnly the most popular options are listed here, please use our online search by terminal PN to find the right tool for your application, and contact us


Installers Kit

Features:A strong all purpose Carry CaseSL110 Jack Termination Tool KitPremium Impact ToolCable Stripper4-Pair Cable testerPalm ToolWire CuttersCross-head & Flat-bladed ScrewdriversInstruction SheetCD-Rom with videos showing step-by-step cable termination & printable instructions

Ideal for Installation, Service and RepairImage representative of type only

Part Number Description mm² (AWG) or other2-1579010-1 110 SL Jacks & AMP TWIST 6S SL 0.2 (24) stranded

0.2-0.4 (24-22) solidOnly the most popular options are listed here, please use our online search by terminal PN to find the right tool for your application, and contact us



Pistol Grip tool kit for 2mm FB + HM

Features:Pistol Grip hand toolModule feed tracks 2 x 4 posn. & 2 x 5 posn.Bench clamp, cable support bar & brushHex. Keys; 1.5, 2.5, 3 & 4mmDurable plastic carry case with foam insertAll you need to apply 2mm FB connectors

1490375-1 for Shielded 2mm FB connectorsImage representative of type only

Pistol Grip Kit for RV-100

Features:Kit Comprises:Pistol Grip Hand ToolBench ClampService Tool Replacement contactsDurable plastic carry case with foam insert.

See relevant Instruction Sheet for exact list

Task specific Kits for RV-100 ConnectorsImage representative of type only

Part Number Description mm² (AWG) or other528405-7 RV-100 23 Posn. 0.06 - 0.4 (30-22)658164-3 RV-100 MULTIPLEXER 16 Posn.

RV-100 32, 48, 64, 80, 96 Posn.; RV-100-4 32 Posn.0.05 - 0.35 (30-22)


VS-3 Hand Tool Kit

Features:Kits comprise:Hand ToolCrimp Height GaugeBlack Nylon ChordRepair TagDurable Plastic Carry-case

Optional Tool Holder 229755-1


Part Number Description mm² (AWG) or other244271-1 PICABOND (28-19)244271-5 PICABOND (includes Tool Holder 229755-1) (28-19)244271-3 PICABOND Mini (28-19)



VS-3 Hand Tool Holder

Features:Cable Clamp with 360˚ rotationSerrated JawsTool lock


Part Number Description mm² (AWG) or other229755-1 VS-3 Hand Tool Holder


Telecoms and Outside Plant Revised: January 2010

10 Pair Splicing Kit

Features:Quick and easy one action terminationSplicing Head has many positioning optionsApplies AMP STACK 10 pair MkIV modules and compatible connectors:Straight Splicing, Pluggable or Half-tapDry or Sealed

A range of specialist kits for 10 Pair AMP STACK applicationsImage representative of type only

Part Number Description mm² (AWG) or other790112-1 GB restricted Brtish Telecom special

Comprises; Carry Case, Hand Tool, Splicing Head, Check Combe and Single Point Insertion Tool

0.4 - 0.9 (22-20)

790112-2 GB restricted to Brtish TelecomComprises; Carry Case, Hand Tool, Splicing Head, Check Combe, Single Point Insertion Tool and Electrical Tester

0.4 - 0.9 (22-20)

790112-3 GB restricted to Brtish TelecomComprises; Carry Case, Hand Tool, Splicing Head, Check Combe, Single Point Insertion Tool and 10 Pair Clamp Bar

0.4 - 0.9 (22-20)

790112-4 GB restricted to Brtish TelecomComprises; Carry Case, Hand Tool, Splicing Head, Check Combe, Single Point Insertion Tool, 10 Pair Clamp Bar and Electrical Tester

0.4 - 0.9 (22-20)

1-790112-1 Comprises; Carry Case, Hand Tool, Splicing Head, Check Combe and Single Point Insertion Tool

0.4 - 0.9 (22-20)

1-790112-2 Comprises; Carry Case, Hand Tool, Splicing Head, Check Combe, Single Point Insertion Tool and Electrical Tester

0.4 - 0.9 (22-20)

1-790112-3 Comprises; Carry Case, Hand Tool, Splicing Head, Check Combe, Single Point Insertion Tool and 10 Pair Clamp Bar

0.4 - 0.9 (22-20)

1-790112-4 Comprises; Carry Case, Hand Tool, Splicing Head, Check Combe, Single Point Insertion Tool, 10 Pair Clamp Bar and Electrical Tester

0.4 - 0.9 (22-20)

1-790112-5 Standard Commercial KitComprises; Carry Case, Hand Tool, Splicing Head, Check Combe, Single Point Insertion Tool, Electrical Tester, Instruction Sheet

0.4 - 0.9 (22-20)

790142-1 Universal KitComprises; Carry Case, Hand Tool, Single Point Insertion Tool, Splicing Head, Electrical Tester, Sparating Tool and Check Combe

0.4 - 0.9 (22-20)



25 Pair Splicing Kit

Features:Quick and easy one action terminationSplicing Head has many positioning optionsApplies AMP STACK 25 pair Mk IIImodules and compatible connectors:Straight Splicing, Pluggable or Half-tapDry or SealedA two position latch feature allows for any combination of module to be terminated

A range of specialist kits for 25 Pair AMP STACK applicationsImage representative of type only

Part Number Description mm² (AWG) or other790131-1 GB Special for Brtish Telecom

Comprises; Carry Case, Hand Tool, Splicing Head, T-Pedestal, Check Combe and Single Point Insertion Tool

0.32 - 0.8 (24-20)

790131-2 GB Special for Brtish TelecomComprises; Carry Case, Hand Tool, Splicing Head, T-Pedestal, Check Combe, Single Point Insertion Tool, Single Pair Tester and Single Point Separating Tool

0.32 - 0.8 (24-20)

790131-3 Standard Commercial KitComprises; Carry Case, Hand Tool, Single Point Insertion Tool, Splicing Head, Electrical Tester, T-Pedestal and Check Combe

0.32 - 0.8 (24-20)


Crimping Pliers

Features:Shut height stop prevents over-crimpingRounded nose won't snag on wiresBuilt-in wire cutter

TELSPLICEImage representative of type only

Part Number Description mm² (AWG) or other790162-1 all TELSPLICE products - sprung-open Jaws 0.4 - 0.9 (22-20)231839-1 all TELSPLICE products - passive Jaws 0.4 - 0.9 (22-20)



Double Point Electrical Tester

Features:A plug-on test probeCan be used held in position or clipped in position

790106-1 - A specifically designed probe acting as an interface between the applied product and test equipment and to prevent damage to the connector Image representative of type only

Single Point Insertion Tool

Features:Comfortable moulded handleMoulded-in metal insert for long life

224290-1 Repair tool for use with AMP STACK1 0 & 25 Pair ModulesImage representative of type only

Part Number Description mm² (AWG) or other224290-1 Not to be supplied to BritishTelecom 0.3 - 0.9 (24-20)790172-1 Prefered by British Telecom over 224290-1 0.3 - 0.9 (24-20)


10 Pair Separator Tool

Features:Robust pressed steel designOne action separation

790104-1 - Designed to separate AMP STACK pluggable modulesImage representative of type only


Check Combe, 10 pair

Features:Simple durable moulded design

356073-1 - visual aid used in AMP STACK modular jointing applications to check wire colour positioning Image representative of type only

Check Combe, 25 pair

Features:Simple durable moulded design

224517-1 - visual aid used in AMP STACK modular jointing applications to check wire colour positioning Image representative of type only

Single Point Separator Tool

Features:Does the same job as 790104-1 but in a progressive waySrung open jaws aid sparation

790141-1 - Designed to separate AMP STACK 10 or 25 pair pluggable modulesImage representative of type only


Splicing Head, 10 Pair with Pedestal Bar, 10 Pair

Features:Snug fit product locationWire combes for wire guidance and separationSpring clamping to holdCompact pedestal bar mounting

1-790114-1 - for AMP STACK Mk IV 10 Pair applicationsImage representative of type only

Splicing Head, 10 Pair

Features:Snug fit product locationWire combes for wire guidance and separationSpring clamping to hold

1-790114-2 - for AMP STACK Mk IV 10 Pair applicationsImage representative of type only

Splicing Head, 25 Pair

Features:Snug fit product locationWire combes for wire guidance and separationSpring clamping to hold

224636-1 - for AMP STACK Mk III 25 Pair applicationsImage representative of type only

Power Assist options Revised: January 2010

Battery Tool Kit


The Tool Kit is supplied in a durable plastic carry case and includes:Battery Tool with the relevant Adapter / HeadBattery Charger 220vTwo Batteries

Spares:1725839-1 - Battery1725840-2 - Battery Charger (EU Power Plug)1725840-3 - Battery Charger (UK Power Plug)

Convert your existing Hand Tools into Powered!Ideal for low to medium production volumes. Image representative of type only

Part Number Description mm² (AWG) or other1213804-2 Double Action Hand Tool (EU Power Plug)1213804-5 Double Action Hand Tool (UK Power Plug)1213805-2 CERTI-CRIMP II SAHT / any CERTI-CRIMP II PN [-3] (EU Power plug)1213805-5 CERTI-CRIMP II SAHT / any CERTI-CRIMP II PN [-3] (UK Power Plug)1213819-2 C-Head SAHT, CLOSED head (EU Power Plug)1213819-5 C-Head SAHT, CLOSED head (UK Power Plug)1213840-2 C-Head SAHT, OPEN head (EU Power Plug)1213840-5 C-Head SAHT, OPEN head (UK Power Plug)1213890-2 SDE Pin Dies, CLOSED head (EU Power Plug)1213890-5 SDE Pin Dies, CLOSED head (UK Power Plug)1725837-2 SDE Shoulder Dies, OPEN head - pictured (EU Power Plug)1725837-5 SDE Shoulder Dies, OPEN head - pictured (UK Power Plug)1901235-2 Heavy Head Hand Tool (EU Power Plug)1901235-5 Heavy Head Hand Tool (UK Power Plug)


Electric Terminator EU

Features:Portable Bench-top Unit

Mains powered unit - no air required (EU mains plug)Switchable 110v or 240v supplyCycle CounterTwo stage crimp cycle optionIncludes Foot switch 1673664-1

539630-1 - Portable Bench-top Unit with foot switch (requires head / Adapter).Ideal for low to medium production volumes. Image representative of type only

Part Number Description mm² (AWG) or other169411 Adapter for CERTI-LOK Dies1213860-1 Adapter for CERTI-CRIMP II Heads1673663-2 Adapter for SDE Dies1901556-1 Adapter for C-Head SAHT Dies2-1579001-3 Mini CERTI-LOK Head for Wire End Ferrules 0.08 - 10.0 (28-8)



Micro Pneumatic

Features:All pneumaticWire range of 0.12 - 2.0 mm² [26-14]Weighing only 0.7 kg (1.5lb)146.5 mm (5.75") long

The Basic system requires: A Power Unit A Tool Holder / Adapter A Head Assembly


Micro Pneumatic Adapter

Features:

Also required:Adapter Holder with Ratchet 356304-1or Adapter Holder without Ratchet 189928-1andHand held power unit 1490567-1

Adapter onlyImage representative of type only

Part Number Description mm² (AWG) or other1583527-1 Adapter for CERTI-CRIMP II SAHT (pictured)



Micro Pneumatic Crimping Head

Features:

Also required:Small Tool Holder with Ratchet 1673611-1andHand held power unit 1490567-1

The listed Heads can also be used in the 626 pneumatic system

Crimping Head onlyImage representative of type only

Part Number Description mm² (AWG) or other314270-3 PIDG Terminals & Splices; PLASTI-GRIP Terminals 0.4 - 1.5 (22-16)314269-1 PIDG Terminals & Splices; PLASTI-GRIP terminals 1.5 - 2.5 (16-14)314868-1 PLASTI-GRIP Butt Splice 0.4 - 1.5 (22-16)314869-1 PLASTI-GRIP Butt Splice 1.5 - 2.5 (16-14)314516-1 SOLISTRAND Terminals & Splices 0.4 - 1.5 (22-16)314517-1 SOLISTRAND Terminals & Splices 1.5 - 2.5 (16-14)314518-1 SOLISTRAND Terminals & Splices 2.5 - 4.0 (14-12)


626 Pneumatic

Features:All pneumaticWire range of 0.12 - 13.0 mm² [26-6]

The Basic system requires: A Power Unit A Tool Holder / Adapter A Head Assembly & Die-set (when applicabe)



626 Pneumatic Adapter

Features:

Also required:Adapter Holder with Ratchet 356304-1or Adapter Holder without Ratchet 189928-1andHand held power unit 189721-1or Foot actuated Power Unit 189722-1

The above Adapter Holders also take Micro Pnuematic Adapters

Adapter onlyImage representative of type only

Part Number Description mm² (AWG) or other525432-1 Adapter for Heavy Head Hand Tool1213563-1 Adapter for Double Action Hand Tool (pictured)


626 Pneumatic Crimping Head (Small Tool Holder)

Features:

Also required:Small Tool Holder with Ratchet 356303-1or Tool Holder without Ratchet 189766-1andHand held power unit 189721-1or Foot actuated Power Unit 189722-1


Part Number Description mm² (AWG) or other217205-1 Closed End Splice 0.4 - 1.5 (22-16)354422-1 Closed End Splice 0.4 - 2.5 (22-14)354422-2 Closed End Splice 0.4 - 6.0 (22-10)314537-1 PIDG, PLASTI-GRIP Terminals & Splices 0.15 - 0.4 (26-22)189989-1 Crimping Head for SOLISTRAND Terminals & Splices 0.4 - 6.0 (22-10)



626 Pneumatic Crimping Head (Large Tool Holder)

Features:

Also required:Large Tool Holder with Ratchet 356302-1or Tool Holder without Ratchet 189767-1andHand held power unit 189721-1 (-2 with Booster]or Foot actuated Power Unit 189722-1 (-2 with Booster]


Part Number Description mm² (AWG) or other189896-1 SOLISTRAND Terminals 1.0 - 10.0 (18-8)189466-1 Closed End Splice 1.0 - 6.0 (18-10)189447-1 COPALUM Terminals and Splices 1.5 - 2.5 (16-14)1320369-1 COPALUM Terminals and Splices - *requires (-2) Power Units! 10.0 (8)189444-1 COPALUM Terminals and Splices 4.0 - 6.0 (12-10)679300-1 PIDG Terminals & Splices; PLASTI-GRIP Terminals 4.0 - 6.0 (12-10)679301-1 Crimping Head for SOLISTRAND Terminals & Splices 0.4 - 6.0 (22-10)1338757-1 SOLISTRAND Terminals & Splices 10.0 (8)1338758-1 SOLISTRAND Terminals & Splices 6.0 (10)217206-1 STRATO-THERM SOLISTRAND High Temp & Heat Resistant Terminals & Splices 0.4 - 6.0 (22-10)904395-1 TERMINYL Terminals & Splices; (PLASTI-GRIP where no insulation crimp is

required)10.0 (8)


Bench Press SSC-2FP

Features:NO GUARDING NECESSARY!

The machine will not operate when the jaw opening is greater than 6mm.Variable pre-hold pressure.

Double Foot Pedal Actuation:First pedal opens the jaws for terminal placement, releasing the pedal closes the head with pre-hold pressure only.Second pedal activates the crimp cycle, pressing the first pedal again allows the crimped terminal to be removed.

1481004-7Ideally suited to: Insulated terminals up to 6 mm² Copper tube terminals up to 16 mm² Wire End Ferrules up to 50 mm²


Part Number Description mm² (AWG) or other3-1481221-6 Adapter for WDT Dies8-1481221-2 Adapter for Service Tool Dies1579000-8 Adapter for SDE Dies8-1481221-3 Adapter for C-Head SAHT Dies


Revised: Hand Tools - KONEL

Documents

Transcript of Revised: Hand Tools - KONEL