Resistance Grounding System
-
Upload
adolfocienfuegos -
Category
Documents
-
view
216 -
download
0
Transcript of Resistance Grounding System
-
8/13/2019 Resistance Grounding System
1/3
Process Industry Practices
Electrical
PIP ELSGS01D
Data Sheet For Design and Fabrication of High
Resistance Grounding System
(Wye System, 600 Volts or Below)
-
8/13/2019 Resistance Grounding System
2/3
PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES
In an effort to minimize the cost of process industry facilities, this Practice
has been prepared from the technical requirements in the existing standards of major
industrial users, contractors, or standards organizations. By harmonizing these technical
requirements into a single set of Practices, administrative, application, and engineering
costs to both the purchaser and the manufacturer should be reduced. While this Practice
is expected to incorporate the majority of requirements of most users, individual
applications may involve requirements that will be appended to and take precedence over
this Practice. Determinations concerning fitness for purpose and particular matters or
application of the Practice to particular project or engineering situations should not be
made solely on information contained in these materials. The use of trade names from
time to time should not be viewed as an expression of preference but rather recognized as
normal usage in the trade. Other brands having the same specifications are equally
correct and may be substituted for those named. All practices or guidelines are intended
to be consistent with applicable laws and regulations including OSHA requirements. To
the extent these practices or guidelines should conflict with OSHA or other applicablelaws or regulations, such laws or regulations must be followed. Consult an appropriate
professional before applying or acting on any material contained in or suggested by the
Practice.
Process Industry Practices (PIP), Construction Industry Institute, The University of
Texas at Austin, 3208 Red River Street, Suite 300, Austin, Texas 78705. PIP member
companies may copy this practice for their internal use.
3pr96
2pr96
Not printed with state funds.
-
8/13/2019 Resistance Grounding System
3/3
PIP ELSGS01Data Sheet for Design and Fabrication of High Resistanc
October 1995 Grounding System (Wye System, 600 Volts or Below
Process Industry Practices Page 1 of
Client: Engineering Org. Spec. No.
Project title Location Date
Project location Contract No. Equip. No.
Proj. No. Specifier Name Tele. No.P.O. No.
Refer to Specification No. ELSGS01 For General Requirements
Applicable State & Local Codes:___________________________________________________________
Data Provided By: n Buyer l Seller With Proposal t Seller After Order
Site Conditions:
Altitude ___________ Ft Seismic Zone ___________
Area Class ______ Div _____Group ____________________
Non Hazardous
Gas Ignition Temp ___________
C
Ambient Temperature: Max ________ F Min________F
Other ____________________________________________
120 Volt AC Control Power /Heater Source:
Internal Source Furnished by Vendor (Part of System)
or
Exernal Source Furnished by Buyer l VA Required ____
Entry:Top Bottom Side Other ______________
Enclosure:
Mfr.s Standard lType _______________________
Steel Aluminum
Outdoor NEMA 3R Outdoor NEMA 4
Outdoor NEMA 4X
Indoor NEMA 1 Indoor NEMA 12
Within switchgear or MCC Lineup
Space Heaters:
Not Required Required
Thermostat Not Required
tSpace Heater Load _________ Watts @ __________Volts
Painting:
Mfr.s Std ANSI 61 Other ________________
Per Paint Spec _______________________________
Other ____________________________
Portable Detectors
Quantity required: None One Two
Shop Inspection & Tests:
nMFR. Standard Tests Witnessed Not Witnessed
Preshipment Shop Witness Inspection
Other ______________________________________
Documentation:
lElectronic Document Format . DXF Other _____
Manufacturer to provide:
1 reproducible plus
________ number of copies of all documentation plus
________ copies of the operating manuals.
Other Requirements: