Residential Addition/Alteration Application (Single Family or Two Family) Building Inspection Department

9915 39th Avenue

Pleasant Prairie WI 53158 Phone: 262.694.9304 Email: building inspection@pleasantprairiewi.gov

Community Development Department

9915 39th Avenue

Pleasant Prairie WI 53158 Phone: 262.925.6717 Email: communitydeveloment@pleasantprairiewi.gov

GENERAL INFORMATION

Job Address Tax Parcel Number

Property Owner

Property Owner is Acting as Contractor

Estimated Cost of Project Estimated date of completion

PROJECT DESCRIPTOION

Work proposed (check all that apply)

Addition

Building Size sq.ft. Height ft.

Describe uses in addition

Siding materials

Roofing materials

Alteration

Alteration area: sq.ft.

Alteration Location (check all that apply)

Basement 2nd Floor

1st Floor 3rd Floor

Garage

Replace Roofing—Roofing material:

Replace Siding—Siding material:

Describe uses in area being altered

Interior Plumbing (complete separate application)

Electrical Work (complete separate application)

HVAC Work (complete separate application

Exterior Plumbing (complete separate application)

MINIMUM SUBMITTAL REQUIREMENTS

Plat of Survey or approved Site Plan showing location of proposed addition and setbacks to property lines and

setbacks to other buildings or structures on the property.

Construction Plans including floor plans (label all rooms)

Building Elevations for an addition (label exterior materials and roof pitch)

Cautionary Statement as attached

Village HVAC/electrical/plumbing permit applications (if applicable)

Written Approval from Architectural Control Committee for an addition (if applicable)

The Village may require additional information be submitted to ensure that all Village requirements are being met. The Applicant will be contacted, if additional information is required to be submitted.

PERMIT REVIEW AND ISSUANCE OF PERMIT

Permits may require up to 10 business days to process. If during the Village’s review of the applications, information is missing or additional information is required, the permit will be put on hold until the information

is received, then the 10 day review period will start again once the additional information is received. The

Applicant will be contacted when the permit is ready to be issued with total permit fees due and permit conditions.

It is the responsibility of the applicant to schedule all required inspections with the Village within 48 hours of the requested inspection.

It is the responsibility of the applicant to provide a copy of the permit conditions to the contractor/owner.

Before digging call Diggers Hotline at 1-800-982-0299 to have all underground utilities marked

INSPECTIONS- scheduled at least 48 hours in advance by calling 262.694.9304 with the Permit

Number 1. Location (staking) Inspection: This inspection is required for all building addition prior to the being

constructed. The applicant is responsible to physically stake the location of the proposed building and the adjacent property lines so that the Village inspectors can readily determine that the proposed building meets the required setbacks. The Village accepts no responsibility for the property owner accuracy of property lines.

2. Footing Forms Inspection is required prior to any concrete being poured (if applicable).

3. Foundation Wall/Backfill Inspection is required prior to backfilling of the foundation (if applicable)

4. Building Drain/Underground Plumbing Rough Inspection (Interior) required prior to basement floor being poured (if applicable)

5. Rough-in Inspections for Carpentry/ HVAC/Electrical/Plumbing required prior to and work being concealed (as applicable)

6. Insulation Inspection required prior to insulation from being concealed.

7. Other Inspections may be required based on the scope of the work.

8. Final Inspection required upon completion of the project, a final inspection shall be scheduled.

REQUIRED SIGNATURES I hereby certify that all of the above statements and attachments submitted, are true and correct to the best of my

knowledge. Furthermore, I understand that for any work started or completed without proper permits, a triple fee will be charged.

I hereby apply for a permit herein described and as shown on the attached required application and plans, and hereby agree that all of the work will be done in accordance with all applicable Village, County, State or Federal codes and ordinance requirements and permit conditions. The applicant further agrees to permit the inspection of the premises by the Village’s Inspectors during regular business hours.

PROPERTY OWNER CONTRACTOR

Company Name:

Print Name: Print Name:

Mailing Address: Mailing Address:

City/State/ZIP: City/State/ZIP

Phone: Phone:

Email: Email:

APPLICANTS SIGNATURE: The applicant, either the property owner or the contractor, is responsible to obtain

the permit, schedule inspections and ensure compliance with all permit conditions.

Signature: Check one:

Owner

Contractor

Date

sf and 2f res addition-alteration app corrected 1-21

Residential 1 & 2 Family MEP Permit Application (HVAC, Electrical, Plumbing)

Building Inspection Department

9915 39th Avenue Pleasant Prairie WI 53158 Phone: 262-694-9304 Email: buildinginspection@pleasantprairiewi.gov

General Information (one application per contractor)

Job Address Tax Parcel Number#

Property Owner as Contractor

(must reside on property)

Date of completion Cost of Project

Project Information (check all that apply)

New Home Existing Home Accessory Structure Addition

Alteration Repair Replacement Electric

Plumbing HVAC Plans Included Specs Included

License Information (please include license number and expiration date)

WI Electrical Contractor License WI Master Electrician Name and License

WI Plumbing Contractor License WI Master Plumber Name and License

WI HVAC Contractor License WI HVAC Qualifier Name and License

Electrical Information (Photovoltaic systems will require plan review, please submit one-line and specs)

Service QTY: Subpanels QTY:

Generator QTY: Photovoltaic KW:

Openings: Pool/Hot tub QTY:

Plumbing Information (“A” value worksheet required for new home)

Sanitary Lateral LNFT: Fixtures QTY:

Water Lateral LNFT: Gas Line LNFT:

Storm Lateral LNFT: Worksheet Included

HVAC

Heating Units QTY: Cooling Units QTY:

Exhaust Fans QTY: Duct Extension LNFT:

Gas Line LNFT: Fireplace QTY:

Project Description

Is this MEP work part of a building construction project YN Project Name:

res mep permit app corrected-rev 1-21

Permit Review and Issuance

Permits may require up to 10 business days to process. If during the Village’s review of the application

information is missing or additional information is required, the permit will be placed on hold. Once the

information is received, the 10-day review period will start over. The Applicant will be contacted when the

permit is ready to be issued with total permit fees due and (if) any additional requirements.

It is the responsibility of the permit holder (applicant) to call and schedule all required inspections with the

Building Inspection Department within 48 hours of the requested inspection date at 262-694-9304.

Before digging, call Diggers Hotline at 1-800-982-0299 to have all underground utilities marked.

Contractor Information Applicant Owner Information Applicant

Company Name

Contact Name Name

Address Address

City/ST/Zip City/ST/Zip

Phone Phone

Email Email

Applicant Signature

I hereby certify that all of the above statements and submitted attachments are true and correct to the best of my knowledge. Furthermore, I understand that a triple fee will apply for any work started or completed without proper permits.

I hereby apply for a permit herein described and as shown on the attached required applications and plans, and

hereby agree that the work performed will be in accordance with all applicable Village, County, State or Federal codes

and references therein. The applicant further agrees to permit the inspection of the project by the Building Inspection

Department inspectors during regular business hours.

Sign(Contractor): Date:

Sign(Master Plumber if applicable) : Date:

Sign(Master Electrician if applicable): Date:

Sign(HVAC Qualifier if applicable): Date:

GENERAL DESIGN STANDARDS FOR A SINGLE FAMILY HOUSE

Community Development Department 9915 39th Avenue Pleasant Prairie WI 53158 Phone: 262.925.6717 Email: communitydeveloment@plprairiewi.com

Zoning District Minimum 1st Floor Area

(sq. ft.)

Minimum Total Floor Area

(sq. ft.)

Building

Heighta

(ft)

Width of dwelling

(ft)

Street

Setbackb

(ft)

Side

Setbackc

(ft)

Rear Setback

(ft)

Shore

Setbackd

(ft)

Wetland Setback

(ft)

Driveway Setback

(ft)

A-2, General Agricultural 1000 1400 35 28 65/40 25 50 50/35 25 5

A-3, Limited Agricultural 1000 1400 35 28 65/40 25 50 50/35 25 5

C-2, Upland Conservancy 1000 1400 35 n/a 65/40 25 50 50/35 25 5

R-1, Rural Residential 1500 2000 35 28 65/40 25 50 50/35 25 5

R-2, Urban Single Family 1500 2000 35 28 65/40 25 50 50/35 25 5

R-3, Urban Single Family 1000 1400 35 28 65/30 10/15 25 50/35 25 5

R-4, Urban Single Family 1000 1400 35 28 65/30 10/15 25 50/35 25 5

R-4.5, Urban Single Family 1000 1400 35 26 65/30 10/15 25 50/35 25 5

R-5, Urban Single Family 900 1200 35 24 65/30 10/15 25 50/35 25 5

R-6, Urban Single Family 700 1200 35 24 65/30 8/15 25 50/35 25 5

MINIMUM SINGLE FAMILY DWELLING STANDARS No building is allowed to be constructed within the 100-year floodplain or within any wetlands.

aBuilding Height Exception if dwelling unit is proposed to be between 35 and 40 feet high then the following is required:

The maximum height shall not exceed 40 feet;

The lot shall have a minimum area of 20,000 square feet; The dwelling shall have a minimum first floor living area of 2,000 square feet and a minimum total living area of 3,500 square feet ("living area"

excludes unfinished basements, garages, decks, porches and patios); The required minimum side setbacks shall be increased by 5 feet; and The required minimum rear setback shall be increased by 10 feet.

The dwelling shall be set on an enclosed permanent foundation unless the soil bearing capacity, as determined by a structural engineer, prohibits such foundation. Placement of the dwelling shall provide for proper drainage away from the foundation and shall accommodate drainage on and through the existing property by not negatively affecting the existing drainage patterns or the capabilities of draining the abutting properties

The length to width ratio of a 1 story dwelling unit (excluded are decks, porches, bay windows, chimneys and any projections less than 25 square feet), as measured at the foundation, shall not be greater than 2 to 1 (i.e. the length shall not be more than twice the width). The length of the dwelling unit is that side of the dwelling that is the longest and the width is that side of the dwelling which is the shortest.

The main roof of the dwelling shall have a minimum roof pitch of 4:12 and the eaves on the main roof shall extend beyond the nearest vertical wall a minimum of 1 foot.

Permitted roof surface materials: wood shakes, asphalt, fiberglass, composition or wood shingles, clay tiles, concrete tiles, slate or other appropriate roofing material as specifically approved by the Village Zoning Administrator

Permitted exterior materials: brick, stone, wood, masonry, concrete, stucco, aluminum or vinyl siding or other appropriate siding material as specifically approved by the Village Zoning Administrator. The exterior siding shall extend to the top of the foundation and be within 6 inches above the final grade

The front facade of the structure shall be placed parallel to the street property line, unless otherwise approved by the Zoning Administrator.

Revised 8-2020

MINIMUM SETBACKSe (setbacks are measured from foundation to foundation or foundation to property lines) bStreet setback: The 1st number is the setback from a right-of-way of any arterial streets or highways. The 2nd number is the setback from all other public

right-of-ways or from the back of curb/gravel shoulder of a private roads. These setbacks are from any adjacent street. Street Setback Exceptions:

The required street setback distance for a dwelling unit may be decreased to the average of the existing street setback distances of the abutting

dwelling units on each side, but in no case shall the setback distances be reduced to less than 15 feet from a Village right-of-way or private roadway or less than 50 feet from a federal, state highway, county highway or village arterial road right-of-way. If one of the abutting lots to be

used in averaging the setback is vacant, then to calculate the average street setback, the street setback on the vacant lot shall be the minimum setback as required in the underlying zoning district.

The required street setback distance may be reduced to 25 feet for dwelling unit in any subdivision platted prior to April 5, 1989 (Village

incorporation date), wherein said subdivision plat had a previously recorded deed restriction indicating a 25 foot street setback.

The required rear street yard setback distance of a principal structure located in a single-family residential district and located on a double or triple

frontage lot which abuts a federal, state or county trunk highway may be decreased to 50 feet where there is no direct access permitted to an arterial street or highway.

cSide setback: If an attached garage is not constructed with a new home, then at least one side setback shall be 15 feet to allow for adequate room for a

driveway to a future detached garage. dShore setback: The 1st number is from the Ordinary High Water Mark (OHWM) of Lake Michigan. The 2nd number is from the OHWM of any other

navigable waterway.

eSetback distances restrictions. Permitted dwelling unit setback distances appropriate to the location and type of development contemplated which are

more restrictive than the regulations of the applicable zoning district may be required by the Village. Examples of this may include, but are not limited to,

the following:

Greater street setback distances may be required on cul-de-sac lots to achieve the necessary lot width, as specified in the underlying zoning district, at the building setback line.

Minimum or maximum street setback distances may be required for a new dwelling unit to provide aesthetically consistent building site lines and

conformance with existing adjacent development.

Special setback distances may be required to protect natural resource elements such as trees.

These are general design standards and other exceptions may be specified in the Village Zoning Ordinance. If the property is located within

a PUD, Planned Unit Development Overlay District additional or variations to the requirements above may be applicable. In addition, property owners are required to follow and Deed Restrictions or Restrictive Covenants that may be recorded on the property.

HOUSE

HOUSE

HOUSE

FRONT

STREET

YARD

FRONT

STREET

YARD

FRONT

STREET

YARD

SIDE

STREET

YARD

FRONT

STREET

YARD

FRONT

STREET

YARD

DR

IV

EW

AY

DR

IV

EW

AY

STREET RIGHT-OF-WAY

ST

RE

ET

R

IG

HT

-O

F-W

AY

HOUSE

HOUSE

HOUSE

FRONT

STREET

YARD

FRONT

STREET

YARD

FRONT

STREET

YARD

FRONT

STREET

YARD

FRONT

STREET

YARD

FRONT

STREET

YARD

DR

IV

EW

AY

DR

IV

EW

AY

DR

IV

EW

AY

REAR

YARD

REAR

YARD

REAR

YARD

REAR

YARD

REAR

YARD

REAR

YARD

STREET RIGHT-OF-WAY

SID

E S

TR

EE

T Y

AR

D

DRIVEWAY

FRONT

STREET

YARD

SIDE

YARD

SIDE

YARD

SIDE

YARD

SIDE

YARD

SIDE

YARD

SIDE

YARD

SIDE

YARD

SIDE

YARD

SIDE

YARD

SIDE

YARD

PROPERTY LINES

(TYP)

ILLUSTRATION 4-A

HOUSE

HOUSE

FRONT

STREET

YARD

FRONT

STREET

YARD

FRONT

STREET

YARD

FRONT

STREET

YARD

DR

IV

EW

AY

DR

IV

EW

AY

STREET RIGHT-OF-WAY

REAR

STREET

YARD

STREET RIGHT-OF-WAY

SIDE

YARD

SIDE

YARD

SIDE

YARD

SIDE

YARD

PROPERTY LINES

(TYP)

ILLUSTRATION 4-B

REAR

STREET

YARD

REAR

STREET

YARD

SIDE

YARD

SIDE

YARD

HOUSE

DR

IV

EW

AY

FRONT

STREET

YARD

FRONT

STREET

YARD