REQUEST FOR QUALIFICATION (RFQ) FOR INTERIOR FURNISHING ... · interior furnishing, electrical,...

INTERIOR FURNISHING, ELECTRICAL, LAN, UPS AND CIVIL WORK FOR STREE NIDHI TELAANGANA

of 20

REQUEST FOR QUALIFICATION (RFQ)

FOR

INTERIOR FURNISHING, ELECTRICAL LAN, UPS AND CIVIL

WORKS

IN FLAT NOS. 501,502 & 505, 5TH FLOOR HUDA BUILDING

HERITAGE COMPLEX, HYDERABAD-500004

FOR

STREE NIDHI

CERDIT CO- OPERATIVE FEDERATION LTD.,

April,2018

Client: -

Stree Nidhi

#5th Floor-502, Huda Building

Heritage Complex, Hill Fort Road,

Hyderabad-500004, Telangana.

Phone no. 09000217817

Consultants: -

# 3-6-134, Flat no. 302,

SVC-ROYAL DM Apartment, Street

no-18, Himayat Nagar,

Hyderabad – 500 029

Ph:040-23261158

Mobile:09866533393

Email:[email protected]

Tender Ref No: 007/SN/PROC/PREMISES/2018-19


of 20

I N D E X

Page

1.0 PREAMBLE 3 - 3

2.0 NOTICE INVITING TENDER 4 - 5

3.0 FORM OF TENDER SUBMISSION 6 - 6

4.0 SCHEDULES A TO E 7 - 11

5.0 GENERAL RULES, TERMS AND CONDITIONS 12 - 16

6.0 TECHNICAL SPECIFICATIONS 17 - 17

7.0 LIST OF APPROVED MAKES FOR MATERIALS 18 - 19

8.0 SPECIAL INSTRUCTIONS TO BIDDERS FOR

E-TENDERING 20 – 20

9.0 FINANCIAL BIDS:

9.0.1 BOQ FOR PROPOSED INTERIOR & CIVIL WORKS

(Annexure I)

9.0.2 BOQ FOR PROPOSED ELECTRICAL & OTHER WORKS

(Annexure II)

9.0.3 FURNISHING LAYOUT

9.0.4 ELECTRICAL LAYOUT


of 20

PREAMBLE

Stree Nidhi Credit Co-Operative Federation Ltd., intends to carry Interior Furnishing, Electrical

LAN, UPS and Civil Works in Flat Nos: 501,502,505, 5th Floor, Huda Building Heritage Complex,

Hill Fort Road - Hyderabad.

Stree Nidhi Credit Co-Operative Federation Ltd. appointed M/S abhikram-s Architects, Interior

Designers, Urban Planners, Valuers, Project Managers, Hyderabad as Interior Consultant for this

project.

As per the terms of appointment of M/S abhikram-s Architects, Interior Designers, Urban

Planners, Valuers, Project Managers, Hyderabad now invites tenders from eligible contractors to

take part in the contractor selection process for Interior Furnishing, Electrical LAN and UPS works

for the above mentioned Flats.

The Contractor’s scope consists of procurement of all materials including fittings & fixtures, accessories, etc. required for Interior Furnishing, Electrical, LAN and UPS works, directed by the

Consultant at site of the Project. The Contractor shall be fully responsible for the quality of

materials & construction standards, workmanship, safety and security at site, certifying the Bills

with recommendations etc.

The Contractor shall carryout all the works under this contract with due diligence by deploying

required men, material, equipment’s, tools, etc. complete as required to execute the work within

the time frame stipulated in the Tender. The works shall be carried out maintaining high quality

standards, as per the standards, Indian Standard Codes or any other relevant codes.

The Contractor shall engage staff experienced in relevant fields to assist the Project In- Charge in

execution of the works.

The tenders i.e. Technical Bids(RFP) and Financial Bids(RFP) can be downloaded from e-

procurement website i.e, https://www.tender.telangana.gov.in also from web site of Stree Nidhi

i.e, htpps://www.streenidhi.telangana.gov.in. From submitted tenders, technical bids shall be

opened first and shall be evaluated for technical competence of the contractor, then financial bids

shall be opened only of the contractors who get qualified in the technical qualification. This RFP

document is being provided to enable Tenderers submit details mentioned in schedules “A” to “E” of this RFP. Offerors shall upload scanned copies of Annexure I & II which illustrates item wise

commercials of BOQ mentioned in Annexure I & II. At the end of the Tender Process, the Bidder

submitting the lowest biding the financial bid shall be awarded the Works envisaged under this

Tender. In case The Consultant and The Client feel that any one of the tenders or bids or all the

tenders or bids are unresponsive, they are free to reject any one or all the tenders or bids and/or

cancel the entire Tender Process and recall for fresh tenders or bids, with same or altered

conditions of contract, without assigning any reason for the same.

Pre-Bid Meeting: Please note that pre-bid meeting shall be a held at Stree Nidhi Credit Co-

Operative Federation Ltd., 5th Floor-502, Huda Building Heritage Complex, Hill Fort Road,

Hyderabad– 500004. On 2nd May, 2018 between 10.30 AM to 11:30 AM.

https://www.tender.telangana.gov.in/


of 20

NOTICE INVITING TENDER

INTERIOR FURNISHING, ELECTRICAL LAN AND UPS WORKS OF 5th FLOOR-

501,502,505 HUDA BUILDING HERITAGE COMPLEX, HILL FORT ROAD HYDERABAD

FOR

STREE NIDHI CREDIT CO-OPERATIVE FEDERATION LTD, HYDERABAD

1. M/S abhikram-s Architects, Interior Designers, Urban Planners, Valuers, Project Managers,

invites sealed tenders, on behalf of Stree Nidhi Credit Co-Operative Federation Ltd.,

Hyderabad in prescribed form, for the following work from reliable, bonafide and

resourceful Contractors experienced in the similar type of works.

Name of Work Completion

Period

Last date& Time of submission

of Qualification document

Interior Furnishing, Electrical Lan, Ups and Civil works of 5th Floor-

501,502,505 Huda Building Heritage

Complex, Hill Fort Road, Hyderabad

30 Days 17th May, 2018@ 4:00 P.M.

2. The estimated cost of the work is aboutRs.28,26,657/-

3. Eligibility criteria:

A. The Tenderers must have completed –

3 (Three) similar works each of 40% (Forty percent) of the estimated cost.

OR

2 (two) similar works each of 50% (Fifty percent) of the estimated cost.

OR

1 (one) similar work of 80% (eighty percent) of the estimated cost.

In the last 3 (Three) consecutive years preceding i.e. 2015, 2016 and 2017.

The Tenderer should furnish required project specific information and evidence in support of its

eligibility criteria, as per format.

It is clarified that similar works means Interior Furnishing, Electrical, LAN, UPS and Civil Works

for clients in Hyderabad.


of 20

Tenderer may be a single entity / company. There shall be no change in control of the Tenderer

during the entire Tender Process or during the Contract Period (if the Tenderer is awarded the

Works in accordance with the terms hereof) without the prior consent of The Client.

The term “control” shall mean (i) the ability to appoint majority of the members on its board of

directors, or (ii) the ability to cast more than 50% (fifty per cent) of the voting rights attaching to

voting securities,

B. Minimum average annual turnover for the last three consecutive financial years immediately

preceding 31stMarch 2017 should not be less than 30% of the Estimated Amount an

Auditor’s certificate shall be submitted in support of the Tenderers annual turnover.

POINTS TO BE NOTED

1. Works envisaged under this contract are required to be completed in all respects within the

completion time set out in paragraph 1 above.

2. The Tender Documents consists of RFQ and RFP documents.

3. The Tender will be available from 27.04.018 to 17.05.2018 (up to 12 pm of 17.05.2018) on

the web site mentioned below.

4. The tender should be submitted at our e-procurement portal

https://www.tenders.telangana.gov.in only. No other mode of submission is permitted.

The last date of the submission of tender 17.05. 2018 up to 05:00 PM. It is to be noted that

the technical bids shall be opened first & the tenderers will be shortlisted. The financial

bids shall be opened only of the shortlisted tenderers.

5. All contractors have to submit Tender document cost (TC) in the form of Demand Draft

for Rs. 1000/- (Rupees One thousand only) in favour of “Managing Director, Stree Nidhi

- Telangana.”

6. All contractors have to submit Earnest Money Deposit (EMD) in the form of Demand Draft

for Rs. 28,500/- in favour of “Managing Director, Stree Nidhi - Telangana”.

7. Offerors shall make a note that as per guidelines issued by the Govt of India, all units

registered under MSME are exempted from paying Application Fee & Earnest Money

Deposit for Government/PSU tenders. All such offerors who are registered as MSME units,

are hence exempted from paying application fee & Earnest Money. In case any offeror

claims exemption from paying such fees, he/she shall mandatorily submit certificate issued

by competent authority for such exemption along with application. Any application

submitted without prescribed fees as well as exemption certificate, shall be summarily

rejected. No consideration for same shall be entertained at the time of opening the bids.

8. Each and every page of the tender and submission should be stamped with the Offeror’s seal and signed by an authorized person.

Original Hard Copy of DD towards tender document cost to be submitted to the office of Stree

Nidhi Credit Co-Operative Federation Ltd., 5th Floor-502, Huda Building Heritage Complex, Hill

Fort Road-Hyderabad before last date of submission of tender.


of 20

FORM OF TENDER SUBMISSION

THIS LETTER SHOULD BE SUBMITTED ON THE TENDERER’S LETTERHEAD

Date:

To,

Managing Director STREE NIDHI CREDIT CO-OPERATIVE FEDERATION LTD., #5th FLOOR-502, HUDA BUILDING HERITAGE COMPLEX, HILL FORT ROAD,

HYDERABAD-500004.

Sir,

I / we have read and examined the following documents forming part of the Request for

Qualification (RFQ) issued on 27.04.2018.

(i) Notice inviting tender

(ii) Form of tender submission

(iii) All terms & conditions, appendices, schedules, BOQ, etc.

I / we understand and agree that only if I / we are qualified in the RFQ stage: our Request for

Proposal (RFP) shall be opened and considered for financial evaluation. Else we are eligible to

ask our RFP back in unopened condition.

I / We agree to maintain firm our prices for a period of (120 days) four months from the date of

tender submission.

I / We understand that The Client or The Consultant is under no obligation to disclose the results

of the selection process and can recall the bids if so desired by them.

Yours faithfully,

Tenderer’s authorized person __________________________

Office Address with date &company seal:


of 20

SCHEDULE - A

IDENTIFICATION AND FINANCIAL DATA SHEET

1. (Firm’s Name)

2. Year of incorporation.

3. Type of incorporation.

4.

(Office Address with contact details)

5. Details of signing authority.

(Name) (Title / Position) (Educational Qualification)

6. Solvency Amount

7. Annual Turnover Give Separately for Each year – last 3 years )

(FY – 2014-15)

(FY– 2015-16)

(FY –2016-17)

Signature of authorized person __________________________

Office Address with company seal

Note: In case of contractors, who are not limited liability Co., submission of solvency certificate

from a nationalized / scheduled bank is mandatory.


of 20

SCHEDULE - B

COMPLETED PROJECT EXPERIENCE (Works for estimated cost mentioned above

only)

Sr. Name of the

project

Name,

address

and

contact

no. of the

client

Brief

description

Starting

date

Completion

date

Value of

work

(lakhs)

Remarks

1

2

3



Note: Submit copies of work orders and completion certificates in support of the above.


of 20

SCHEDULE – C

LIST OF PERSONNEL

Sr. Name Educational

qualification

Experience

in the field

(Years)

Experience

in the

organization

(Years)

Brief

details of

work

profile

Details of

project

experience

Remarks

1

2

3

4

5

6

7

8

I / We hereby confirm that I / We will engage the required number of personnel to the site. I / we

also confirm that I / we will depute additional personnel if so required in the opinion of the client

/ consultants at no extra cost.



Note: Separate sheets shall be attached to cover the details in above format only, if required.


of 20

SCHEDULE – D

ON GOING PROJECT EXPERIENCE (As on date of submission of tender)

Sr. Name of

the

project

Name,

address

and

contact

no. of the

client

Brief

description

Starting

date

Scheduled

completion

date

Present

status

Value

of work

(lakhs)

Remarks

1

2

3




of 20

SCHEDULE – E

LIST OF MACHINERY AND EQUIPMENTS AVAILABLE WITH TENDERER

Sr. Name No. of

Units

Type

&Make

Capacity Owned /

Leased

1. Machinery & Tools for steel

fabrication

2. Welding equipment

3. Tile cutting machine

4. Electrical works tools and tackles

5. Relevant safety equipment and tools

6. Any other specifically relevant



Note: Separate sheets shall be attached to cover the details in above format only, if required.

Tenderer shall submit the details of litigation history, if any, on separate sheet of paper. In case of

no litigation history it should be mentioned specifically as “No Litigation History”.


of 20

GENERAL RULES, TERMS AND CONDITIONS

These general rules shall be applicable to entire RFP to the extent the context permits and are

intended to supplement the provision in the particular section. In case of any discrepancy, the

provision in the particular section shall be taken precedence. The following contains a description

of general requirements to be part of the scope of work.

1. Inspection of site – Before submitting The Tender, The Tenderers should inspect the Site

and shall get themselves acquainted thoroughly with the site conditions. They shall also collect

such information, as they may deem necessary for the proper execution of the Works. In any case

Tenderers shall be deemed to have inspected the Site and have notice of any relevant site

conditions and no Tenderer may make any claim for extension of time or financial compensation

on any grounds relating to information relating to the Site or its conditions.

2. Any missing information – Clarity of drawings or The Contractor’s request for modification of any drawing to suite his working feasibility shall not constitute the ground for claiming any

extension of time for construction or any extra costs.

3. Language – Only “ENGLISH” language shall prevail for all correspondence under this Contract.

4. Mobilization at Site – The Work shall be planned and carried out such that there is no

disturbance to the operations of the adjacent existing facilities. The Contactor shall mobilize and

commence work within Three days from the issuance of work order.

5. Standard of Workmanship & Materials – All work shall be executed with the best

workmanship and to the accepted standard practices. Relevant code of practices shall be followed

unless otherwise indicated in accompanying drawings / specifications or where otherwise directed

by The Consultant.

6. Contractor’s Employees – The Contractor shall provide and employ on the site for

execution of the works only such technical personnel who are skilled and experienced in their

respective fields and competent for proper execution of the work. Skilled, semiskilled and

unskilled labour as necessary for the proper and timely execution of the works.

The Contractor shall be fully responsible for the payment of the salaries to his employees or the

employees of subcontractor, subagents, suppliers, their safety and security. The Contractor

indemnifies The Client/ The Consultant from any of his obligations to his employees, labour, sub-

contractor, subagents, suppliers etc. neither The Client nor The Consultant have any obligation to

employ his staff/engineers/workers at any stage.

The contractor shall maintain all records regarding the labour/workers/employees and the salaries

being paid to them at site. He shall also maintain the necessary EPF and ESI for all his workers,

labour etc. as per the statuary regulations. Same shall be shown to the Client/ the Consultant when

asked for.


of 20

7. Security – The Contractor at his own cost shall make provisions for the security of the site

of works, material, etc. He shall also provide at his own cost for protecting and securing all places

dangerous whether to The Contractor's workmen or to other persons until the work shall have been

handed over to The Client.

8. Care of Works – From the commencement to the completion of works The Contractor shall

take full responsibility for the area thereof. In case any damage, loss or injury shall happen to the

works or to any part thereof or to any temporary works from any cause whatsoever shall at his

own cost repair and make good the same so that at completion, the works shall be in good order

and condition and in conformity in every respect with the requirements of the contract and The

Consultant's instructions. In the event of any such damage, loss, injury happening due to the

default of The Contractor he shall to the extent required by The Consultant, repair and make good

the same as aforesaid at his own cost.

9. Safety at Works – The Contractor shall make adequate arrangements during the work Period

for the safety of workers and users in accordance with Good Industry Practice and notify The

Consultant / The Client about such arrangements.

In case of any happenings /accidents on site/site premises shall be immediately brought to the

notice of The Consultant and The Client.

10. Security Deposit – Successful contractor shall deposit 3% of the total bid in the form of

Demand Draft towards security deposit. Earlier deposited EMD shall be converted into security

deposit making total of 5% security deposit.

11. Retention – Every running account bill & final bill shall be subjected to deduction of 5% of

the certified bill amount towards retention amount. The EMD, SD and retention amount of 10%

shall be returned to the contractor at the end of defect liability period i.e.at the end of 12 months

from the date of successful completion of entire work.

12. Payment of Taxes, Duties, etc. – The Contractor shall pay all the taxes, duties, levies etc. to

the respective State, local and any other authorities deemed necessary, existing as on date or any

other new taxes that may be levied as per new laws at later date. Non-payment of such duties taxes,

levies, etc. by The Contractor shall be considered as The Contractor’s event of default. Neither The Client nor The Consultant will be responsible for such default of The Contractor.

The Consultant/ The Client reserve the right to make such payment on behalf of The Contractor

and the same shall be deducted from any amounts/ bills that are due to The Contractor.

13. Confidentiality – The Contractor, his personnel, subcontractors, agents, suppliers, etc. shall

treat the details of the contract as private and confidential and shall not disclose any matters

connected with the contract or the works to any third person other than as required under the

contract, except to the extent necessary to carry out their respective obligations under the contract

or to comply with Applicable Laws or the requirement of a Government Authority. The

Contractor (and his personnel) shall not publish or disclose any particulars of the works prepared


of 20

by the other Party without the previous consent of the other Party. However, The Contractor shall

be permitted to disclose any publicly available information, or information otherwise required to

establish its qualifications to compete for other projects with prior written approval of The Client

/ The Consultant.

14. Access to Site - The Consultant and any person authorized by him shall at all times have

access to the works and to the Site where work is being prepared or materials, manufactured

articles or machinery are being obtained for the works and The Contractor shall afford every

facility for and every assistance in or in obtaining the right to such access.

15. Site supervision – The Project Management Consultant (PMC) appointed by The Client will

supervise all the work for the quality, workmanship, prior inspection and with respect to safety.

16. Project Schedule – The entire Works must be completed as per below format from issuance

of work order & the site shall be handed over to The Client. Tenderers shall note that Time is the

essence of this contract.

Name of Work Completion Period

Interior Furnishing, Electrical, LAN, UPS and Civil Works

of Stree Nidhi @ 5th floor-501,502,505 Huda Building

Heritage Complex, Hill Fort Road - Hyderabad.

30 days

18. Penalty - If the Contractor fails to complete the works / items of work in all respects and hand

over the same to The Client within the stipulated project completion date or approved extended

time, the Contractor shall pay to The Client Rs. 2000/- per day or any part thereof to the maximum

5% (FIVE percent) of the Total Contract Value as penalty. The Client may without prejudice to

any other method of recovery deduct the amount of such penalty from the security deposit or any

payments due to the Contractor.

19. Specification of Work– The Works shall be carried out as per the Technical Specifications

stipulated in the Tender and as per consultant’s instructions.

20. Materials – All material used for the work shall be of good quality and approved by the

consultant.

21.Escalation – No escalation shall be applicable for this Agreement. All quoted prices are firm

and binding for the entire Contract Period.

22.Peace at Site – The Contractor shall at all times during the progress of the work take all

requisite precaution and use his best of endeavours for preventing any riotous or unlawful

behaviour by or amongst the workers and other employed on the Works and for the preservation

of peace and protection of inhabitants and the security of property in the neighbourhood of the


of 20

Works. He shall also pay the charges of such special police (if any), as the Consultant may deem

necessary.

23.Labour Laws – The Contractor shall follow all the provisions regarding employment of young

persons covered by the Employment of Children Act, 1938, the Factories Act, 1948 as amended

from time to time shall be fully complied with. The Contractor shall also see that the provisions

set for under other Applicable Laws relating to labour and employment as amended from time to

time are fully complied with by him.

24. Insurance – The insurance shall be against all losses and damages from whatever causes.

Other than expected risks, for which the Contractor is responsible under The Contract. The

insurance cover shall be for all material, men, etc. and for the entire period of The Work & till it

is handed over to the Stree Nidhi Credit Co-Operative Federation Ltd., 25. Billing – Only one running bill can be submitted during progress of work. Final bill shall be

submitted to The Client by the Contractor in triplicate on satisfactory completion of entire work.

All bills shall be reflecting all the taxes and duties paid separately.

26. Measurements – The Consultant shall accept as otherwise stated and determined by

measurement the value of work in accordance with the contract. All items having financial value

shall be recorded in measurement book. The Contractor and the Consultant will finalize format

for Measurement Book (MB) mutually. The Contractor and The Consultant shall take

measurements jointly. Before taking the measurement, The Consultant will verify and ascertain

the completion of the same. No item of work, which is incomplete, shall be measured or

sanctioned for payment. In case of Defects or improper workmanship the same will not be

measured. The Contractor shall without any extra charge provide all assistance with every

appliance and other necessary thing for measurement. Measurements shall be recorded and signed

by both parties on the site after completion of measurement. Measurements wherever specified

shall be in accordance with the procedure set forth in the schedule of Rates / Specifications not

withstanding any other provision in the relevant standard method of measurement. In case of items

not specified in the schedule measurements shall be in accordance with the relevant standard /

methods issued by the IS 1200 and measurements should be in metric system only. For purpose

of clarity, the specifications and condition of contract govern in all cases.

The schedule of quantities unless otherwise stated shall be deemed to have been prepared in

accordance with the Standard Procedure and shall be considered to be approximate and no liability

shall attach to The Consultant for any error that may be discovered therein. The variation may

occur and no claims whatsoever will be entertained for the same. The contractor should evaluate

the quantities on their own for verification based on data and drawings provided in the RFP

document.

27.Housekeeping & Cleaning– The Contractor shall at all times keep his work spots, site, office

and surrounding clean and tidy, free from dust, rubbish, scrap, surplus material and unwanted tools

and equipment. All scaffolding and temporary structures shall be removed as soon as the job for

which these are intended is completed. The welding and other electrical cables shall be routed to

allow safe traffic by all concerned. All equipment and piping shall also be kept clean by regular


of 20

cleaning or protective methods. The Contractor shall provide adequate staff for above purpose.

The removal of debris generated from existing structures must be disposed off by The Contractor

at his own cost and risk. Contractor has to make alternate arrangement, if needed so, for disposal

of debris on his own with no additional payment. If it is observed that the debris are not cleared in

proper manner, Rs.5,000/- shall be deducted from the contractor’s payment towards penalty.


of 20

TECHNICAL SPECIFICATIONS

1. Material:

Specifications of Materials – For all specifications refer Indian Standard (IS) Codes. If the

specification of any material is not mentioned in IS code then the other standards as approved by

the consultant shall be followed. Specifications of materials, which have been specified to

conform to Indian Standards, have been partially reproduced from the relevant Standards. These

partial reproductions have been made to only indicate specific requirements where alternative

choices are mentioned in the IS code and to bring out some of the quality characteristics for ready

reference. The specifications in the relevant Standards shall however be followed, unless it is

specifically mentioned that a particular requirement of the relevant Standard is dispensed with or

is varied and the extent thereof is mentioned.

Wherever an IS code, which is referred to in RFP is amended, or revised, or superseded or is

merged into another IS code or if split into more than one Standard, either the IS code referred to

in RFP or any of the subsequently amended / revised / superseded / merged / split IS code as

applicable may be followed, as alternative specification. Where any particular alternative out of

two or more alternatives given in an IS code is adopted and this alternative also figures in the

amended, revised, merged or split up IS code; the alternative specified in RFP shall be followed.

Materials to be Approved – All materials to be provided by The Contractor shall be in accordance

with the specifications mentioned hereunder. Where specifications are not given, the materials

shall conform to the quality standards specified in respective IS code. Samples of materials,

fittings etc., shall be submitted by The Contractor for the approval of The Client / The Consultant

before bulk supplies are brought on the site of works.

The Contractor shall satisfy The Client / The Consultant that the materials provided by him

conform to the requirement of the specifications and are as per the samples approved by The Client

/ The Consultant. Where materials are specified to comply with the requirements of an IS

Specification, The Contractor shall, if required, furnish the manufacturer's certificate that the

materials satisfy the requirements of the IS code.

The costs of all the tests, if any, on all materials are deemed to be included in the lump-

sum price and shall not be paid extra.

The Consultant may reject any material, if he feels that it is not satisfactory,

notwithstanding the manufacturer's certificate. All rejected material shall be immediately

removed from the Site at the Contractor's own cost.

Any material, which is rejected as unsuitable by The Consultant shall be replaced by The

Contractor at his own expense.


of 20

LIST OF APPROVED MAKES FOR MATERIALS FOR ABOVE WORKS LIST OF APPROVED MANUFACTURERS / NATURAL SOURCES OF MATERIALS TO BE USED

IN THE ABOVE WORKS SUBJECT TO THE APPROVAL OF SAMPLES BY THE CONSULTANT.

S.N. MATERIAL NAME. BRAND / MANUFACTURER.

1. PLYWOOD – MR (Moisture

Resistant, Termite Resistant &

Borer Resistant) –

CONFIRMING TO IS : 303.

GREENPLY / ARCHID/GOLDEN PLY / NICON PLY

2. LAMINATE – CONFIRMING

TO IS : 2046-1995

GREENLAM / ROYAL TOUCHE / ARCHID

3. GLASS MODIFLOAT / ASAHIFLOAT / SAINT GOBAIN MAKE.

4. HARDWARE. EFFICIENT GADGETS / EARL BEHARI (EBCO) / HARDWIN /

ETALICA.

5

FLUSH DOOR –

CONFIRMING TO IS : 2202

(Part – 1) – 1991

GREENPLY / EGG WOOD OR EQUIVALENT.

6 BEECH WOOD. AS APPROVED BY THE CONSULTANT.

7

VENEER. (4MM AND PAPER

VENEER) – GROUP

MATCHED, STRAIGHT

GRAIN.

TRUWOOD /CENTURY / ARCHID

8 BLOCK BOARD. TRUWUD / ARCHID / GREENPLY

9 GI SUPPORT SYSTEM FOR

FALSE CEILING.

SAINT GOBAIN MAKE

10 GI DRY WALL PARTITION

SYSTEM.

RONDO / BMS OR APPROVED EQUIVALENT.

11 PLASTER BOARDS. SAINT GOBAIN MAKE

12 SOFT BOARD. JOLLY BOARD OR APPROVED EQUIVALENT.

13 SCREWS. GKW NETTLEFOLD OR APPROVED EQUIVALENT.

14 ADHESIVES. MOVICOL / FEVICOL SH / ARALDITE OR APPROVED

EQUIVALENT.

15 PAINT. ASIAN / ICI / BEGER OR APPROVED EQUIVALENT.

16 FLOOR SPRING. EVERITE, EBCO OR APPROVED EQUIVALENT.

17 DOOR CLOSURES. STEARLING MECH

18 TEXTURED PAINT. TERRACO / SPECTRUM OR APPROVED EQUIVALENT.

19 VINYL FLOORING. ARMSTRONG OR APPROVED EQUIVALENT.

20 WRITING BOARD. WHITE MARK OR APPROVED EQUIVALENT.

21 DOOR LOCKS. DOORSET OR APPROVED EQUIVALENT.

22 HINGES. C.I. HINGES OF PALLDIUM / JYOTHI BRAND OR ANY

REPUTABLE BRAND.

23. CEILING TILES. ARMSTRONG / BMF / BORAL OR EQUIVALENT.


of 20

LIST OF APPROVED MANUFACTURERS / NATURAL SOURCES OF MATERIALS TO BE

USED IN THE ELECTRICAL WORKS SUBJECT TO THE APPROVAL OF SAMPLES BY

THE CONSULTANT.

S.No. Material Name. Brand / Manufacturer / Recommended

Make. 1. Switches/Sockets MDS (Mosaic) / MK India / Anchor Woods / Clipsal.

2. Copper Conductor wires Finolex / Qflex/ Lapp/ Anchor

3. PVC conduits & Accessories Precision / Sudhakar/ Avon plast

4. MS Conduits Gupta / Bharat

5. Metal clad Sockets MDS /L&T- Hager /Merlingerin /BCH

6. MCBs /MCB Distribution boards MDS /L&T- Hager /Merlingerin(Compact)

7. MCCBs/Switchgear GE Power /Merlin Gerin(Compact) /BCH /L&T /MD

8. Underground Cables CCI /Unistar /Nicco /Gloster

9. Cable Glands HMI /Comet

10. Capacitor Bank Epcos /Neptune

11. Cable Lugs Dowell's / 3D

12. MV Panels (PCCs) Manufacturers with CPRI Test Certificate.

13. ELRs/CBCT Prokdvs /Nagoba

14. Measuring Instruments Prokdvs /Enercon

15. Selector Switches Vaishno / Salzer / Kaycee

16. Indication Lamps LED (protected type)

Schneider / Vaishno / Binay

17. Resign cast CTs AE / Kappa

18. Telephone Wires Lapp / Delton /National

19. Light Fixtures Philips / Tulip / GE

20. Ceiling Fans & Exhaust Fans Crompton/Usha / Polar / Khaithan / Bajaj

NOTE:

The contractor shall use only above mentioned material or equivalent make to be approved by

the Consultant. All other materials shall confirm to the specifications laid down. The tenderer

shall take this into account while tendering rates / prices. The Consultant/Owner has got every

right to select any of the above Makes for the Project. However, Owner/Consultant before

Execution shall be approved the samples of every material including all fixing accessories.


of 20

SCHEDULE – F

SPECIAL INSTRUCTIONS TO BIDDERS FOR E-TENDERING The Bidder should bear all the costs associated with the preparation and submission of their bid

and Stree Nidhi will in no case be responsible or liable for these costs, regardless of the conduct

or outcome of the bidding process. Stree Nidhi. invite offers (Technical offer and Commercial offer) through online from eligible,

reputed vendors.

Applications can be downloaded from Government of Telangana e-Procurement Website

https://www.tender.telangana.gov.in under login for suppliers also from the website of Stree

Nidhi i.e, https://www.streenidhi.telangana.gov.in. Aspiring parties who have not registered

in e-procurement should register before participating through the website

https://tender.telangana.gov.in

The details of the process of registration and obtaining the digital signature certificates are

available on the websitehttps://tender.telangana.gov.in Necessary hands on training could be

obtained from the centre for M/s Vupadhi Techno Services Pvt. Ltd and could also be obtained

over telephone at +91 40-39999703, 39999704 Fax +91-40-39999702 or mail to

[email protected]. can access the application on the website, fill them with

all relevant information, and submit the completed application and supporting documents

a. Read the complete document, carefully PDF versions or scanned copies of the

required documents are to be uploaded on the website.

b. The system will generate an acknowledgement with a unique offer submission

number on successful completion of the above process.

c. For any help or technical support on e-Procurement, Bidders may contact Vupadhi

Techno Services Pvt. Ltd over phone or in person or their helpdesk at: e-Procurement Help

Desk.

Vupadhi Techno Services Pvt. Ltd.

1st Floor, Ramky Grandiose,

Sy. No: 136/2 & 4, Gachibowli,

Hyderabad - 500032.

Telangana State.

+91 40-39999703, 39999704

+91 40-39999702

[email protected]

www.vupadhi.com

Contact details of Stree Nidhi: Dr.P.Raja Rao – Dy.General Manager – Stree Nidhi

Contact Number: 9000217817; Email: [email protected]

https://www.tender.telangana.gov.in/

https://tender.telangana.gov.in/

https://tender.telangana.gov.in/

Item./Particulars with description Quantity Unit Rate in Figures Rate in words AMOUNT

1 FULLY GLAZED DOOR (GD)

a MAIN ENTRANCE DOOR FOR OFFICE 3'-0"x 8'-0" 2 NOS 48

b DOOR FOR WORK STATION AREA 3'-6"x 7'-0" 1 NOS 24.5

c DOOR FOR CONFERENCE AREA 3'-6"x 7'-0" 1 NOS 24.5

d FROM EXISTING OFFICE TO NEW 3'-6"x 7'-0" 1 NOS 24.5

2 PARTLY GLAZED DOOR FOR (GD) 3'-0"x7'-0" NOS

Annexure I

BOQ FOR THE PROPOSED INTERIOR WORKS OF STREE NIDHI CREDIT COOPERATIVE FEDERATION LTD OF 5TH FLOOR HERMITAGE OFFICE COMPLEX ADARSH NAGAR HEAD OFFICE HYDERABAD FURNISHING & CIVIL WORKS.

S.no

Providing ,supplying, and fixing in position of Main Entrance glass door of 3'-0" wide in 12mm thk clear float glass , TOUFGHENED edges with crystal/pencil polished alround, fixed with beach wood frames top and bottom rails of 6" & 4" with melamine polish as per the design and drawing provided with SS brush finished handles 2'-0" long and 3/4 dia of approved shape and design fixed over the floor spring, pivote bottom lock etc with etched film with logo of the corporate office on the doors making complete as per the design.The rate shall be inclusive of all the necessary material,required hardware, labour, transportation, necessary for the complete execution of the item.

sqft

sqft

sqft

sqft

Providing ,supplying, and fixing partly glazed door of 35mm thk solid core flush door with beach wood frame of 3"X1 1/2" finished with 1.0 mm thk laminate on both sides with lipping around the door of 35mm x19 mm in BEACH wood, and 6 mm thk float glass inside the door fixed with beach wood beading from a ht of 1'-0" to 6'-0"

form bottom as per the desing ,with hinges,tower bolts, door stoppers,mortice lock,handles of s.s and door silencers of s.s mat finished of kich company or equivalent making complete as per the design.The rate shall be inclusive of all the necessary material,required hardware, labour, transportation, necessary for the complete execution of the item.

a UPS ROOM DOOR 3'-0"x 7'-0" 1 NOS 21

b TOILET LOBBY DOOR 3'-0"x 7'-0" 1 NOS 21

c CONFERENCE ROOM 1 NOS 3'-0" X 7'-0" 21

d CONFERENCE LOBBY 1 NOS 3'-0" X 7'-0" 21

e CONFERENCE PANTRY LOBBY 2 NOS 3'-0" X 7'-0" 42

f STORE ROOM 1 NOS 3'-0" X 7'-0" 21

3 FULL HEIGHT SOLID PARTITION .

a UPS ROOM 210

b TOILET LOBBY ROOM 115

c CONFERENCE ROOM 625

d CONFERENCE PANTRY LOBBY 2 NOS 3'-0" X 7'-0" 122

e STORE ROOM 130

sqft

sqft

sqft

sqft

sqft

sqft

Providing & fixing in position metal stud FULL HEIGHT SOLID partition with the following specifications:A) supporting system comprising of best locally available make 51 X 35 X 0.55 mm thick metal studs @ 600 mm c/c and 51 X 32 mm metal tracks at floor, middle, door and ceiling level with joints staggered. The verticals should touch the ceiling with horizontal ceiling channel at slab/beam bottom. The rate should include necessary strengthening with studs/tracks or channel at doors and other openings.B) 9 mm BWR plywood fixed on both sides with 25 mm dry wall screws.

C) 1 mm laminate of given color n shade on both sides up to false ceiling level.making complete as per the design.The rate shall be inclusive of all the necessary material,required hardware, labour, transportation, necessary for the complete execution of the item.

sqft

sqft

sqft

sqft

sqft

4LOW HEIGHT GLAZED PARTITION IN LAMINATE UPTO 4'-0" ht

c) 85x15mm beech wood capping on top and sides of openings.

a DGM CABINS 363

b ZM CABINS 110

5 LOW HEIGHT SOLID PARTITION IN LAMINATE UPTO 4'-0" ht

Low Height Partition: Providing & fixing metal stud low height Partitions with following specifications.

a) Supporting system comprising of best locally available make 51 X 35 mm metal studs at 600 mm c/c and 51 X 32 mm metal tracks at floor, middle and at 900 mm level with joints staggered. The rate should include necessary strengthening with studs/tracks or channels at openings.

b) 9mm plywood BWR grade with 1mm laminate (as per banks uniform color scheme) on both sides.

d) 12mm glass of 12”height on top of low height partition (total height to be 1200mm ) with necessary beach wood beading and etching work wherever required also to be fixed. The beech wood members to have melamine polish finish. Anti termite solution to be sprayed before using the ply wood in the work.

making complete as per the design.The rate shall be inclusive of all the necessary material,required hardware, labour, transportation, necessary for the complete execution of the item.

sqft

sqft

Low Height Partition: Providing & fixing metal stud low height Partitions with following specifications.

a) Supporting system comprising of best locally available make 51 X 35 mm metal studs at 600 mm c/c and 51 X 32 mm metal tracks at floor, middle and at 900 mm level with joints staggered. The rate should include necessary strengthening with studs/tracks or channels at openings.

c) 85x15mm beech wood capping on top and sides of openings.

a SHARING PARTITION (RUNNING COUNTER) 180.4

b CM CABINS 70.4

7

a RUNNING TABLE 20'-6"x 2'-0" 4 nos 85 NOS

b CM RUNNING COUNTER TABLE 8'-9"x 2'-0" 4 nos 35 NOS

b) 9mm plywood BWR grade with 1mm laminate (as per banks uniform color scheme) on both sides.

The beech wood members to have melamine polish finish. Anti termite solution to be sprayed before using the ply wood in the work.


sqft

sqft

RUNNING COUNTER TABLES WITH SHARING PARTITION IN BETWEENProviding,supplying and fixing in position the Running Counter tables in 19mm thk BWR ply of ISI make and IS :303 on top,side supports and foot rest ,with all top surfaces finished in 1.0 mm thk laminate of approved colours with all exposed edges comoflaged to 19 mm with ply and lipped with 38mm thk beachwood lipping over the edges as per the design and polished to same colour The tables shall be provided with 8MM THK TOUGHFENED glass seprator with brackets ,Wire manager finished with synthetic enamel paint on the internal surfaces with approved colour etc making complete as per the design.The table shall accommodate one drawer with telescopic channels,locks, and storage cabinet with 19mm same ply with same specification as table and ss handles of 4" ht locks etc, making complete as per the design.The rate shall be inclusive of all the necessary material,required hardware, labour, transportation, necessary for the complete execution of the item.

8 LOW HEIGHT STORAGES/CREDENZAS HT 2'-6" & 4'-0" HT

a DGM TABLE 7'-6"X2'-6" 6 NOS 123.75 SFT

b ZM TABLE 8'-9"x 2'-0" 4 NOS 57.75 SFT

c IN CORRIDOR AT CM 14'-0" x 4 '-0" 1 NO HT 4'-0" 56 SFT

d 74 SFT

9

a AMSTRONG CEILING 2400 SFT

Providing, supplying, and fixing in position of the low height credenzas drawer/storage unit of size 1'-6" depth and 4'-0" ht with sides, top verticals and horizontal and shutters in 19mm thk BWR ply of ISI make and IS 303 and carcass back in 12 mm thk BWR ply of ISI make and IS 303 finished in 1mm thk laminate of approved colour on exposed surfaces with two coats of luppum and synthetic enamel paint on internal surfaces of approved colour with beach wood lipping over all edges and polished to approved colour as per the design with,handles,locks as required.The rate shall be inclusive of all the necessary material,required hardware, labour, transportation, necessary for the complete execution of the item.

OVER HEAD STORAGE IN CORRIDOR 20'-0" x 1'-6" 1 NO HT 2'-0" 11'-0"X 2'-0" 2 NOS IN CM AREAS

FALSE CEILING IN COMBINATION OF 80% ARMSTRONG GRID CEILING AND 20% GYPSUM BOARD CEILING

False ceiling shall be done in combination of Armstrong grid ceiling and gypsum to an extent of 80% and 20% respectively.Gypsum board ceiling shall be done in places as per the drawing as per standard specifications of Indian Gypsum and ceiling for the rest o f entire hall shall be done in Armstrong grid ceiling.

Providing and fixing in the true horizontal level false ceiling system of Armstrong world industries. The suspension system shall be the Armstrong Trulock Silhouette revealed profile grid system with 15mm wide flanges incorporating a 3mm or 6mm central recess color black or white revealed Silhouette main runners and cross tees to

b FALSE CEILING IN GYPSUM BOARD. SAINT GOBIN 1250 SFT

have mitered ends with birds mouth notches to provide mitered cruciform junctions. Main runners to be spaced at 12mm c/c fixed by using 2mm pre straightened GI Wire.Main tee,rotary stitched of size 15mm x44mmx3600mm at every 1200mm c/c maximum and 1200mm cross tee of size 15mmx44mm x1200mm at every 600 mm c/c maximum and 600mm c/c cross tee of size 15mmx44mmx600mm at every 1200mm c/c maximum and 19mmx19mmx3000 wall angle allround the wall to form grid size of 600mmx600mm and suspending the grid using 2mm prestraightened GI Wire and 6mm nylon raw plug at every 1200mm intervals at the main tee and laying of dunne premier micro look mineral fiber tiles manufactured by Armstrong world industries of size 600mmx600mmx15mm over the formed grid completeas directed.

Note: the work includes cost and conveyance of materials and labour charges includings .All Operational charges tools lifts and all heights etc surfaces of the false ceiling should be with drop ceiling.Manufactures specifications to be strictly followed.No extra shall be payable for making cutouts and providing frame for cutouts of for making staggred ceiling.


Providing, supplying, and fixing in position of Gypsum Board False Celing as per manufacturers specification and instructions with 12.5 mm thk board.Gypboard Screw- fixed to the underside of suspended G.I grid.G.I grid should be constructed and suspended from the main ceiling as per the manfacutures instructions and as per the specifications using original Co. Specified framework sections G.I24 Guage the Gypboard should be fixed to G.I Grid with 25mm long Drawali Screws.the Gypboard to be used should be12.5mm thk tapered edge boards.the boards should be taped and filled from underside to give smooth,seamless ceiling. The rates should include necessary additional ceiling sections and intermediate channels openings for light fixtures,vertical drops offsets etc.

10 PAINTING

WALL PAINTING

a

3200 SFT

CEILING PAINTING

b 1500 SFT

11 BLINDS: 250 SFT

Addtional Intermidaite Channels should be fixed to strap hangers for additional support to prevent strap hangers from buckling swaying at every 1200mm. Item to be completed in all respects including necessary sleeves for ducts finishings of joints cutouts supports for light fixtures A.C grills speakers etc.


Providing, supplying, and applying of N.C.L ALTEX finish to the walls of three coats and finished with Emulsion paint to the walls of approved and shade to suit the interiors of the corporate office. The rate shall include scrapping and preparing of the surface etc making complete fo applying of paint complete as per the desing.

The rate shall be inclusive of all the necessary material,required hardware, labour, transportation, necessary for the complete execution of the item.

Providing and applying of paint to the ceiling of two coats luppum and one coats of primer and two coats of emulsion paint of approved colour to suit the interiors of the bank. The rate shall include scrapping rubbing and preparing of the surface etc making complete for applying of paint.making complete as per the design.


Providing supplying and fixing of transperent Roller blinds of approved make,shade and texture of hunter douglas make or eqvivalent using good quality of roller mechanism of Acmeda or equivalent as per the design and direction.The rate shall be inclusive of all the necessary material,required hardware, labour, transportation, necessary for the complete execution of the item.

12 6 SFT

13 CONFERENCE TABLE 16'-6"X5'-0"X2'-6" 16 RFT

PANTRY COUNTER IN PANTRY IN CONFERENCE HALL 2'-0" WIDTH

Providing, supplying, and fixing running counter with 19mm thk bison ply for the top and 19 mm thk vertical supports sides finsihed in 0.4 mm thk laminate for all the internal surfaces and the top finished in the granite with half round edges in machine polishing with the basic rate of granite @ RS 175 SFT.making complete for applying of paint.making complete as per the design


Providing, supplying, and fixing of Conference Table of size 16'-6"x5'-0"x2'-6" with 25 mm thk ply bwr as Table Top and edges of the same comoflanged with 12mm thk ply for 6" inside from edge of the ,edges lipped with 38mm swidth and 3/4 ' thk beach wood beading ,with all the internal surfaces of the table top cladded with .8 mm thk and the exposed surfaces shall be with 1mm thk laminate as per the directions and design.

The Vertical supports and shall be with double ply 18mm thk comoflanged with 1mm thk laminate on all the exposed surfaces with edges lipped with 38mm width and 3/4 " thk beach wood beading as per the design.The modesty panel in box type shall be of 18mm htk ply with all internal surfaces shall be laminated with 0.8 mm thk, the external surfaces laminated with 1mm thk laminate as per the design.All the Beach wood beadins shall be melamine polished to suit the decor of the table. as per the drawing and design.


14 350 SFT

TOTAL FURNISHING WORKS

CIVIL WORKS

1 BRICK WORK

1.1

a FOR CLOSING THE DOOR 21 CFT

2 FINISHING

2.1

a FOR WALLS 85 SFT

WOODEN PANELING TO THE WALLS upto 4'-0" ht AND COULMNS FULL HTProviding, supplying, and fixing in position paneling over the walls surfaces to certain extent with t.w scantalting of 1"x2" at 2'-0"x2'-0" c/c and 12mm ply ISI make and IS 303 over the exposed surfaces and finished with 1mm thk lamiante of approved shade and colour.The boxing shall be in 18mm thk BWR ply of ISI make and IS :303 grade and shall be finished with 1mm thk laminateof approved colour and shade as per the design and direction of the architect and .


Providing and Constructing Autoclaved Aerated concrete Blocks Masonry works 600x200x200mm thk in CM 1:6 prop.for wall of 200mm thk as per manufactures specifications including cost of all materials labour racking out joints watering, scaffolding and all incidental and operational charges etc., complete and as directed by Engineer-in-charge/Architect.

Plastering in 2 coats with 16mm thk 12mm thk in CM (1:6)prop and top coat 4mm thk in CM (1:4)prop for internal walls with dubara sponge finishing including cost and conveyance of all materials seignorage fee, all taxes, water to work site and all operational, incidential labour charges such as scaffolding, mixing, motor, lift charges, curing etc. complete for finished item of work as directed by the Engineer in charge/Architect

3

a FOR TOILETS 262.4 SFT

4 DOORS

4.1

a FOR TOILETS 750 mm X 2100mm 8 NO.S 140 SFT

Flooring with Rustic /Non skid tiles of 1st quality of KHAZARIA / JOHNSON / ASIAN make of 7.3 mm thick of approved colour not less than 300x600mm set over a base coat in C.M (1:6) , 12 mm thick incluidng applying neat cement slurry honey like consistency spread at the rate of 3.30kg/Sqm and filling the joints with white cement mixed with pigments of matching shade laid over existing concrete bed/RCC slab including cost of base coat, cost and conveyance of all materials, excluding CC bed/RCC slab, labour charges for mixing cement mortar , laying of tiles to required slopes/levels, curing etc complete for finished item of work for all Floors in Toilets.BASIC COST OF THE TILES 85

Providing and fixing frame made from 1.2 mm powder coated cold rolled steel profiles of overall section size of 60 mm x 45 mm with 21 mm rivet for shutter with necessary stiffeners hinges and screws. V- Board shutter with alround style “U” lipping of size 15 x 18 x 15 mm made from 0.8 mm thick CRCA powder coated steel profile with 16 mm thick V-board with necessary screws fixed at every 1’-0” interval 250 mm long aldrops 2 nos. M.S. nickel coated 250 mm long 1 no. M.S. Tower Bolts Including cost and conveyance. with 1.5mm thk laminate on either side as per approved colour, labour charges etc.,.1 No. eye viewer and 1No. rubber bush including fixing the fixtures to door with required number of screws, bolt and nuts including all labour charges for making and fixing the frame in position as directed by the Engineer in charge, fixing the shutter duly fixing required fixtures to the frame etc., complete for finished item of work (The vertical frame of door shall be embedded in flooring for a depth of not less than 10 mm)

5 Pantry Platform in Black Galaxy (Without Sink )

5.1

a For pantry 5 RFT

6 Dismantling Work

39 CFT

7 SANITARY AND WATER SUPPLY

7.1 806.25 SFT

7.2 4 NO.S

Providing and Laying platform of 2'0" width and 2'8" height(Top) above FFL of approved 20 mm thk granite with bull nose edges,supported on a 25 mm thk wooden top.rate shall be inclusive of making cutouts and polishing the edges for18"x18" s.s nirali sink without drain board (medium).A flexible pipe from sink to the nahni trap shall be provided.rate shall be one jaquar continental C.P SWAN NECK TAP with swinging casted.

Dismantaling and Removal of Brick works and carting away as directed covering the entire work area of dismantaling with green mesh to avoid fall of debris as per the directions of the Engg of the Bank. The rate shall be inclusive of all the,labour, transportation necessary required for the complete execution of the item.

Dadooing in toilets with Rustic tiles 300x600 MM , 1st quality ) over a base coat of 12 mm thick in CM (1:5) prop incluidng applying neat cement slurry honey like consistency spread at the rate of 3.30kg/Sqm and jointed with white cement mixed with pigment of matching shade including cost and conveaynce of all materials and labour charges etc. complete for finished item of work to walls in toilets as directed by the Department. BASIC COST OF THE TILE IS RS 85

Supplying and fixing of 150mm x 100mm SWG gully traps of ISI make confirming to ISI 651 & 4127 with C.I grating & constructing brick masonry in CM (1:6) prop. intermediate chamber and fitted with 304.8 mm X 288.6 mm (12"x9") C.I Frame with hinged cover of standard make as approved including cost and conveyance of all materials to site, labour charges., etc complete for finished item of work.

7.3 8 NO.S

7.4 4 NO.S

7.5 4 NO.S

7.6 5.5 SFT

Supplying and fixing 100 mm dia inlet - 75 mm (3") outlet CI floor traps 1st quality ISI marked conforming to IS 1729-1979 with C.P grating fixing with white cement as per the site requirements with standard practice including CP cockroach trap with gratting, black painted for all floors including cost and conveyance of all materials to site, labour charges etc, complete for finished item of work.

Providing & Fixing star white colour vitreous china wall mounted wc with heavy duty soft close seat cover & concealed dual tank. Complete with all accesseries including cutting & making good wall & floor wherever required. Model - CROMA - 2085, 550X367X355mm, 2385 seat cover

Providing and fixing Jaquar make white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets .

Providing & fixing 12 mm thick toughened frosted glass partition Between the Urinals of ht 900 mm up to 5' ht & fixed to wall.Special patch fittings at directed locations.Patch fittings having side patch with EPC lock. The rate shall be inclusive of all the hardware necessary for the complete execution of the item as per the design.

7.7 4 NO.S

7.8 4 NO.S

8 WATER SUPPLY WORKS

8.1 25 RFT

8.2 4 NO.S

Counter Wash Basin Fixing ¾” thk machine cut, machine polished, first quality selected granite counter top with 1:2 cement and mortar base in shape and size as shown in the drawing. 1 1/4th " Kadappa base to be provided below finished granite slab for necessary support. Fixing a wash basin KOHLER -make with all necessary fittings.Model-( K-14715IN-1 Parliament Vessels.lavatory in white available only with single-hole drilling) complete with necessary support and filling up joints with white cement with relevant matching colour, including curing, rubbing, polishing, manual rubbing wherever required on the granite counter & cutting hole for wash basin. 3" band in granite to be provided on the front edge of the counter as per detail drawing and / or as directed. SELECTED GRANITE: BELGIUM BLUE STONE KALINGA to be used as countertop. KOHLER - make single lever basin mixer to be fixed inside wash basin.Model (K-18057IN-ND Touchless cold only lavatory faucet without drain in Polished Chrome Rate to be without wash basin and wash basin mixer & other

Supplying and Fixing of Towel ring Jaquar make continental , Chrome plated with 7 years warranty with necessary screws etc., complete including cost and conveyance of all materials, labour charges for finished item of work in all floors.

Providing and fixing chlorinated poly vinyl chloride(CPVC) pipes having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fitting, including fixing the pipe with clampsat 1m spacing. This includes jointing of pipes and fitting with one step CPVC solvent cement and cost of cutting chases and making good the same including testing of joints complete as per

direction of Engineer in Charge.20 mm OD pipe

Supply and fixing of Health Faucet of the closet mounting type with hose connected Two Way Bib Cock with flow restrictors/ aerators with complete fittings. (All fittings of approved make) Fittings of PARRYWARE MAKE, MODEL Nos. T9941A1, T9915A1, G3434A1) (Flow rate - 1.3 LPM@ 58 PSI)

8.3 4 NO.S

9 3600 SFT

10 2725 SFT

TOTALCIVIL WORKS

SUMMARY

FURNISHING WORKS TOTAL

CIVIL WORKS TOTAL

TOTAL RUPEES

DISCOUNT IF ANY

GRAND TOTAL

Supplying and Fixing of Short Body Bib Cock of ISI make , Chrome finish with 3 years warranty with necessary fittings etc., complete including cost and conveyance of all materials, labour charges for finished item of work in all floors.

Diluting and injecting chemical chemical emulsion for POST CONSTRUCTIONAL anti-termite treatment, as per the directions.The rate shall be inclusive of all the necessary material,required hardware, labour, transportation, necessary for the complete execution of the item.

Cleaning the existing tiles with OXALIC ACID after Completion of the work, as per the Directions.The rate shall be inclusive of all the necessary material,required hardware, labour, transportation, necessary for the complete execution of the item.

DESCRIPTION OF ITEM QTY. UNIT Rate in Words Amount

1

1.1

a 1No.,100A,FP, Changeover Switch +

1 no.125A,TP,MCCB 25 KA as incomer

b 12 nos. 63A, FP, MCB outgoing

c 3 nos.63/40 DP MCB outgoing

e 1 no., 0-125 A, Ammeter with CT and selector switch

f 1no., 0-500V, Voltmeter with selector switch and fuse

g

h 1Set, RYB, indicating lamps with resistors and fuses

Full Set as above 1.00 SET

1.2

a 1 no.,63A, TPN, ELCB (100mA) incomer

b 12 nos, 6-16A, SP, MCB outgoing Full set as above 2.00 SET

Annexure II

BOQ FOR THE PROPOSED INTERIOR WORKS OF STREE NIDHI CREDIT COOPERATIVE FEDERATION LTD OF 5TH FLOOR HERMITAGE

OFFICE COMPLEX ADARSH NAGAR HEAD OFFICE HYDERABAD ELECTRICAL WORKS.

SR.NO

Rate in figures

MAIN LT PANEL / DBs

Supply and installation of main LT panel, wall mounted front operated totally enclosed vermin proof, indoor non-drawout-cubicle type power panel fabricated out of 2mm thk CRCA sheet having gasketed hinged cover on each cubicle fully powder coated after seven tank treatment, incorporating horizontal and vertical sleeved copper busbars, complete with all internal wiring, danger board, two earthing legs, cable chamber etc. as required, housing below-mentioned switchgears / meters. ( GA drawing of the panel got to be approved by Bank / Architect)

(MCCB - L&T/MDS, MCB-MDS/Hager)

2 Set, TPN, Copper busbars of size 25mm x 5mm

thk PVC insulated suitable for 200 Amp load

Suply and installation of 4 way, TPN MCB type lighting distribution Board flush mounted on wall, sheet metal fabricated, powder coated , having dust - proof and vermin proof, gasketed and hinged door with all internals such as DIN rails, neutral - link, interconnected wiring, complete with earthing lugs housing following switchgears (LDB / PDB), ( Double Door DB of MDS / SEIMENS)

1.3

a 1 no, 40/63A, DP, MCB incomer

b 10 Nos. 6/10 AMPS, SP, MCB, outgoing


1.4

a 1 no, 63/40A, DP, MCB,


1.5 5.00 Nos.

1.1.B GENERATOR PANEL

1No.,160A,FP, MCCB

1Set, RYB, indicating lamps with resistors and fuses


2.O CABELS / MAINS WIRING

2.1

S & I of 12 WAY SPN, DB similar to above but for distribution of input power to UPSs as per SLD having below mentioned switch gears ( Earth bar inside these DB should be insulated from the body ) ( UPS - INPUT - DB)

S & I of SPN, DB similar to above but for distribution to all computer power points on work stations for UPS INPUT & OUTPUT

S & I of 63/40A DP MCB in sheet metal powder coated box giving supply to Cassette AC machines & Vault.

SAME AS ABOVE PANEL SPECIFICATION AS PER APPROPRIATE

SIZE

1 Set, FPN, Copper busbars of size 25mm x 5mm

S & I of 1100V grade armoured cable having sector / circular shaped aluminium / copper conductor PVC insulated cores, laid up, PVC tape wrapped inner sheathed, GI strip / wire armoured and overall extruded PVC sheathered confirming to IS: 1554, laid on wall / ceiling using GI clamps & spacers as per route shown at site and further as directed by Bank / Architect in following sizes.

2.1.2 100.00

2.1.2

A 8.00 Nos.

2.1.3 35.00

2.1.4 150.00

3.O POINT WIRING

3.1

3.1.1Primary light points including the cost of 5A switch

60.00

3.1.2 Secondary light points looped from the above point 40.00

3.1.3 Secondary 5A Plug point on switch board 8.00

3.1.4 31.00

3 1/2 C x70 Sq.mm Aluminium mtr.

S & I of end termination of above mentioned cables including compressed type brass glands, crimping type copper lugs, insulation tape etc. as required complete with earthing of glands in following sizes.

3 1/2 C x70 Sq.mm

Supply & laying of concealed wiring using 600v grade 4RX6 sqmm copper conductor PVC insulated wires (with proper R,Y,B color code ) pulled through heavy gauge PVC conduits laid concealed over false ceiling or in wall chases including circuit wires from the relevant DB and also including 2.5 sqmm green color copper earth wire as directed.(FOR LDB/PDB INCOMING)

mtr.

Supply & laying of concealed wiring using 4 core 6 sqmm copper conductor PVC insulated wires (with proper R,Y,B color code ) pulled through heavy gauge PVC conduits laid concealed over false ceiling or in wall chases including circuit wires from the relevant DB and also including 2.5 sqmm green color copper earth wire as directed.(FOR Cassette ACS ) .

mtr.

Supply & Installation of concealed point wiring using 600v grade 3R of 1.5 sqmm copper conductor PVC insulated wires pulled through heavy gauge 2mm PVC conduits laid concealed over false ceiling or in wall chases including circuit wires with 3R of 2.5 sqmm to the relevant DB and including switches & sockets as approved by the consultant .Each circuit feeding not more than 8 points 800 watts as per following configuration.

Pts

Pts

Pts

Wall mounted and Exhaust fan point consisting of 5A socket near fan and switch on light switch board 9 WALL,3 EXHUAST

Pts

3.2 50.00

3.3 50.00

3.2 7.00

4 LIGHTING FIXTURES

4

4.2.2 37.00 Nos.

4.2.3 58.00 Nos.

4.2.4 6.00 Nos.

4.2.7 20.00 Nos.

S & I of point wiring for UPS or stabilized power plug points on workstations / table for computers using 3R X1.5 Sqmm Cu., PVC sheathed white color flexible cable pulled through heavy guage 2mm PVC rigid conduits run within wooden / metal partitions Each point consisting of 3 nos of 3/5 pin sockets & 1 no of 15A Switch , wired together forming one point .The earth wire to be of yellow / green color only ( Only two tables served by one circiut from UPS-DB)

Pts

S & I of points similar to above but to be used as raw power point on the tables consisting of one 5/15A socket with switch of other color and flexible cable socket with switch of other color and flexible cable ( 2 tables served by one circuit from LDB/PDB)

Pts

S & I of 15 AMPS plug points point wiring for xerox etc using 2 R X4.0 Sqmm Cu and 1R of 1.5 sqmm PVC sheathed white color flexible cable pulled through heavy guage 2mm PVC rigid conduits run within wooden / metal partitions Each point consisting of 1 nos of 15 AMPS pin sockets & 1 no of 15A Switch , wired together forming one point .The earth wire to be of yellow / green color only the circuit laid directly through DB to point.

Pts

S & I of lighting fixtures as per the details given below including necessary hardware such as , clamps,nuts, bolts, nails, screws and suspension chains as required for fixing the fixtures in position as directed by Bank / Architect.

a) Recess mounted LED Luminaire 36 x 1W Class LED, Wipro make code: LM - 036 - XXX - WH - XX.

b) Recess mounted LED Down lighter with Pressure die cast aluminium housing (18 x 1W), Wipro, Crompton,phillps

250mm dia wall mounted exhaust fan of decorative plastic body and blade with louvers on the outside (Newtek/ Crompton / Approved equivalent)

cove lighting patti tubes warm lights of 4'-0" length

5 EARTHING

5.1 1.00 Nos.

5.2 50.00

5.3 1.00 Nos.

5.4 50.00

6 TELEPHONE

6.1 Supply and installation of KRONE connector box 20-pair box 1.00 Nos.

6.2 20.00 Nos.

7 LAN WORKS

1.1

40.00

1.2

aRJ-45 for data points

50.00 points

bMounting Cord 7 ft Make D- LINK

50.00 NO

S & I of earth pit comprising of 600mm x 600mmx 3mm. thick copper plate buried at a minimum depth of 2.5 meter including necessary materials like charcoal,salt etc as required conforming to BIS standards having brick masonary chamber with hinged cover and watering arrangement.

supplying and laying of 8 SWG copper bare wire laying through suitable PVC pipes. Mtrs

S & I of earth pit comprising of 600mm x 600mmx 3mm. thick GI plate buried at a minimum depth of 2.5 meter including necessary materials like charcoal,salt etc as required conforming to BIS standards having brick masonary chamber with hinged cover and watering arrangement.

supplying and laying of 8 GUAGE GI wire laying through suitable PVC pipes.

Mtrs

Supply and laying 2 pairs of 0.51mm dia copper conducted PVC insualted telephone wire in 25mm dia heavy duty PVC conduits with acc.including supply and fixing of RJ-11 TELEPHONE OUTLETS of modular type with GI box plate etc.

Supply and fixing the following sizes of PVC medium grade ISI marked conduits (IS : 9537 Part-III) complete with accessories such as bends, junction boxes, pull boxes etc., in recess or on surface including cutting chases in the walls/floors and making good the same complete as required.

25 mm dia 2mm wall thickness mts

Providing and laying Cat 6 cable for data in existing conduits data (Make: MDS) and providing & terminating with RJ-45 (Krone / DELL make) with face plates in suitable modular / MS box from server / enclosure room to individual work stations.

cMounting Cord 3 ft Make D- LINK

50.00 NO

8 INVERTOR WIRING

75.00

TOTAL RUPPES

DISCOUNT IF ANY

GRAND TOTAL

Supply & Installation of concealed INVERTOR wiring using 600v grade 2R of 1.5 sqmm copper conductor PVC insulated wires pulled through heavy gauge 2mm PVC conduits laid concealed over false ceiling or in wall chases .

Mtrs

REQUEST FOR QUALIFICATION (RFQ) FOR INTERIOR FURNISHING ... · interior furnishing, electrical,...

Documents

Transcript of REQUEST FOR QUALIFICATION (RFQ) FOR INTERIOR FURNISHING ... · interior furnishing, electrical,...