Reproduction - bsintek.basco.combsintek.basco.com/BriggsDocumentDisplay/lgiruKX.-FzXFix2.pdf · Add...
2
BTXPV22700E Overview WARNING Failure to read and follow the operator’s manual and all operating instructions can result in death, bodily injury, and/or property damage. WARNING Fuel and its vapors are flammable and explosive. Turn off engine and wait at least 2 minutes before refueling. Let spilled fuel evaporate before starting engine. Always allow space for fuel expansion. WARNING Outdoor use ONLY. DO NOT start or run engine indoors or in an enclosed area, even if windows and doors are open. Running engines give off carbon monoxide, an odorless, poison gas that can cause nausea, fainting or death. WARNING DO NOT put hands or feet near or under rotating parts. Turn off engine and remove the spark plug wire before performing any checks or service to the machine. WARNING This cutting machine is capable of throwing objects. Failure to observe the following safety warnings could result in serious injury to the operator or bystanders. • Do not operate the walk-behind mower without proper guards or other safety devices in place. • Remove objects that could be thrown by blade. • Keep the area of operation clear of all persons, particularly small children and pets. Items Included OPERATOR’S MANUAL Grass Catcher Bag Side Discharge Deflector SAE30W Oil FreshStart™ Fuel Preserver Cartridge Operator’s Manual Unpack the Mower 1. Remove everything from carton except for mower. 2. Open carton completely by cutting each corner from top to bottom. 3. Remove the clear plastic sheet from the top of the engine. 1. Remove the knob, lock washer, and bolt from each side of the handle base. 2. Loosen, but do not remove, the knobs on the handle. 3. Lift the handle to the operating position, and tighten the upper knobs. 4. Reinsert the lower handle bolts through the handle base and handle. (Most users prefer the middle position). 5. Install the lock washers and knobs. Tighten by hand. 1. Hold the bail control against the handle and pull the recoil rope handle out to the rope guide on the handle. 2. Hook the recoil rope into the rope guide (it may be a tight fit). 1. Move the mower outside to a flat, level surface. 2. Remove the oil fill cap. Add the entire contents of the supplied oil container into the engine. Replace the oil fill cap. 3. Remove the fuel fill cap. Following the three-step instructions on the Fresh Start™ card, snap the fuel preserver cartridge into the bottom of the fuel fill cap. 4. Add clean, fresh UNLEADED fuel with a minimum of 87 octane, leaving one inch of space from the top of the tank for fuel expansion. 5. Replace the fuel fill cap and wipe up any spills. Read the Operator’s Manual for operating, maintenance, and safety instructions. Quick Switch 3-in-1 Convert from Mulching to Bagging to Side-Discharge Convert to Mulching Convert to Side-Discharge 1. For mulching, leave the mulching cover in place. Ensure the mulching plug is installed correctly, with the arrow pointing up. 1. Lift the mulching cover. Ensure the mulching plug is installed correctly. 2. Install the side discharge deflector onto the mower deck. Ensure the deck tabs stick up through the locking slots. 3. Release the mulching cover (it will lay on top of the side discharge deflector). Bail Control Ignition Switch Oil Fill and Dipstick Mulching Cover Fuel Fill Cap Recoil Rope Handle Cutting Height Adjust Lever Refer to the Operator’s Manual for instructions on how to start, operate, adjust, or perform maintenance on the mower. NOTICE: The battery may require charging before use in mower. Refer to the Operator’s Manual for complete battery instructions. 1. Slide the frame assembly into the grass bag. Ensure the handle is on the outside of the grass bag. 2. Attach the clips to the side of the frame assembly. 3. Attach the clips to the top and bottom of the frame assembly. On some models, the side mounted discharge deflector is temporarily attached (for shipping purposes) to the rear of the mower. Before assembling the grass catcher bag, remove the side mounted discharge deflector). Form NO: 7104079 (Rev. - ) Quick Setup Guide BTXPV22700E Self-Propelled Mower Have Questions ? Do not return to store. We can help. Call Customer Service Toll-Free 1-800-743-4115 A B C D E F Assemble the Handle A Assemble the Grass Catcher Bag B Set Up the Recoil Rope Handle C Add Oil and Fuel NOTICE: Mower is shipped without oil in engine. Failure to add oil will result in engine damage. NOTICE: Fuel tank hold less than ½ gallon. Do not overfill. NOTICE: DO NOT mix oil with fuel. NOTICE: DO NOT use E85 fuel. D E Convert to Bagging 1. Assemble the grass catcher by sliding the bag over the frame assembly and slipping the bag clips over the frame. 2. While lifting and holding the rear door open, attach the grass catcher to the rear of the mower. 3. Ensure the hooks on either side of the catcher frame hook onto the rear door rod. 4. Release the rear door (it will lay on top of the grass catcher). F G H H G NOTICE: The mulching plug should be removed only when bagging is desired, and should be replaced as soon as bagging operations are completed. NOTICE: Before attaching the grass bag to the mower, the mulching plug should be removed, and should be replaced as soon as bagging operations are completed. Drive Lever Battery Charger Not for Reproduction
Transcript of Reproduction - bsintek.basco.combsintek.basco.com/BriggsDocumentDisplay/lgiruKX.-FzXFix2.pdf · Add...
BTXPV22700E Overview
WARNING Failure to read and follow the operator’s manual and all operating instructions can result in death, bodily injury, and/or property damage.
WARNING Fuel and its vapors are fl ammable and explosive. Turn off engine and wait at least 2 minutes before refueling. Let spilled fuel evaporate before starting engine. Always allow space for fuel expansion.
WARNING Outdoor use ONLY. DO NOT start or run engine indoors or in an enclosed area, even if windows and doors are open. Running engines give off carbon monoxide, an odorless, poison gas that can cause nausea, fainting or death.
WARNING DO NOT put hands or feet near or under rotating parts. Turn off engine and remove the spark plug wire before performing any checks or service to the machine.
WARNING This cutting machine is capable of throwing objects. Failure to observe the following safety warnings could result in serious injury to the operator or bystanders.
• Do not operate the walk-behind mower without proper guards or other safety devices in place.
• Remove objects that could be thrown by blade. • Keep the area of operation clear of all persons, particularly small children
and pets.
Items Included
OPERATOR’SMANUAL
Grass Catcher Bag
Side Discharge
Defl ector
SAE30W
OilFreshStart™ Fuel
Preserver Cartridge
Operator’s Manual
Unpack the Mower 1. Remove everything from carton except for mower. 2. Open carton completely by cutting each corner from
top to bottom. 3. Remove the clear plastic sheet from the top of the
engine.
1. Remove the knob, lock washer, and bolt from each side of the handle base.
2. Loosen, but do not remove, the knobs on the handle.
3. Lift the handle to the operating position, and tighten the upper knobs.
4. Reinsert the lower handle bolts through the handle base and handle. (Most users prefer the middle position).
5. Install the lock washers and knobs. Tighten by hand.
1. Hold the bail control against the handle and pull the recoil rope handle out to the rope guide on the handle.
2. Hook the recoil rope into the rope guide (it may be a tight fi t).
1. Move the mower outside to a fl at, level surface. 2. Remove the oil fi ll cap. Add the entire contents of
the supplied oil container into the engine. Replace the oil fi ll cap.
3. Remove the fuel fi ll cap. Following the three-step instructions on the Fresh Start™ card, snap the fuel preserver cartridge into the bottom of the fuel fi ll cap.
4. Add clean, fresh UNLEADED fuel with a minimum of 87 octane, leaving one inch of space from the top of the tank for fuel expansion.
5. Replace the fuel fi ll cap and wipe up any spills.
Read the Operator’s Manual for operating, maintenance, and safety instructions.
Quick Switch 3-in-1 Convert from Mulching to Bagging to Side-Discharge
Convert to Mulching
Convert to Side-Discharge
1. For mulching, leave the mulching cover in place. Ensure the mulching plug is installed correctly, with the arrow pointing up.
1. Lift the mulching cover. Ensure the mulching plug is installed correctly.
2. Install the side discharge defl ector onto the mower deck. Ensure the deck tabs stick up through the locking slots.
3. Release the mulching cover (it will lay on top of the side discharge defl ector).
Bail Control
Ignition
Switch
Oil Fill and
Dipstick
Mulching
Cover
Fuel Fill Cap
Recoil Rope
Handle
Cutting Height Adjust Lever
Refer to the Operator’s Manual for instructions on how to start, operate, adjust, or perform maintenance on the mower. NOTICE: The battery may require charging before use in mower. Refer to the Operator’s Manual for complete battery instructions.
1. Slide the frame assembly into the grass bag. Ensure the handle is on the outside of the grass bag.
2. Attach the clips to the side of the frame assembly. 3. Attach the clips to the top and bottom of the frame
assembly.
On some models, the side mounted discharge defl ector is temporarily attached (for shipping purposes) to the rear of the mower. Before assembling the grass catcher bag, remove the side mounted discharge defl ector).
Form NO: 7104079 (Rev. - )
Quick Setup GuideBTXPV22700E Self-Propelled Mower
Have Questions ?Do not return to store. We can help.
Call Customer Service Toll-Free 1-800-743-4115
A
B
C
D
E
F
Assemble the Handle A
Assemble the Grass Catcher Bag B
Set Up the Recoil Rope Handle C
Add Oil and FuelNOTICE: Mower is shipped without oil in engine. Failure to add oil will result in engine damage. NOTICE: Fuel tank hold less than ½ gallon. Do not overfi ll.NOTICE: DO NOT mix oil with fuel. NOTICE: DO NOT use E85 fuel.
D
E
Convert to Bagging
1. Assemble the grass catcher by sliding the bag over the frame assembly and slipping the bag clips over the frame.
2. While lifting and holding the rear door open, attach the grass catcher to the rear of the mower.
3. Ensure the hooks on either side of the catcher frame hook onto the rear door rod.
4. Release the rear door (it will lay on top of the grass catcher).
F
G
H
H
G
NOTICE: The mulching plug should be removed only when bagging is desired, and should be replaced as soon as bagging operations are completed.
NOTICE: Before attaching the grass bag to the mower, the mulching plug should be removed, and should be replaced as soon as bagging operations are completed.
Drive
Lever
Battery Charger
Not for Reproduction
Visión general del modelo BTXPV22700E
ADVERTENCIA Si no se leen y siguen las indicaciones del manual del operario y todas las instrucciones de uso, se pueden producir daños materiales, lesiones o incluso la muerte.
ADVERTENCIA El combustible y sus vapores son infl amables y explosivos. Pare el motor y espere al menos dos minutos antes de repostar combustible. Antes de poner en marcha el motor, espere a que
se evapore el combustible que se haya podido derramar. Siempre deje espacio que permita la expansión del combustible.
ADVERTENCIA SÓLO para uso a la intemperie. NO arranque ni deje funcionar el motor en interiores ni en zonas cerradas, incluso con las ventanas y las puertas abiertas. Los motores en funcionamiento desprenden monóxido de carbono, un gas inodoro y venenoso que puede producir náuseas, desmayos o incluso la muerte.
ADVERTENCIA NO ponga las manos o los pies cerca o debajo de las piezas giratorias. Apague el motor y quitar el cable de la bujía antes de realizar cualquier control o el servicio a la máquina.
ADVERTENCIA Esta máquina de corte es capaz de lanzar objetos. El incumplimiento de las advertencias de precaución puede resultar en lesiones graves al operador o los transeúntes.
• No utilice el cortacésped sin dispositivos de protección o dispositivos de seguridad de otros en su lugar.
• Retire los objetos que puedan ser lanzados por la cuchilla. • Mantenga el área de operación libre de todas las personas, especialmente niños pequeños y las
mascotas.
Artículos incluidos
OPERATOR’SMANUAL
Desviador de descarga lateral
Boisa para césped
Aceite
SAE30W Cartucho conservador
de combustible
para arranque fácil
Manual
del usuario
Cómo desempacar el cortacéspedes 1. Saque todo el contenido de la caja de cartón, a excepción
de la cortacéspedes. 2. Abra completamente la caja de cartón cortando cada una
de sus esquinas de arriba abajo. 3. Retire la hoja de plástico transparente de la parte superior
del motor.
1. Quite la perilla, la arandela de seguridad y el perno de ambos lados de las base del asidero.
2. Afl oje pero no quite las perillas del asidero. 3. Alce el asidero hacia su posición de operación y apriete
las perillas superiores. 4. Vuelva a insertar los pernos inferiores del asidero a través
de la base del asidero y el asidero en sí (casi todos los usuarios prefi eren la posición intermedia).
5. Instale la arandela de seguridad y apriete bien las perillas.
1. Oprima y mantenga oprimido el control de motor y cuchilla contra el asidero de conducción, y hale hacia afuera el mango del cable de arranque hasta la guis de cable en el asidero.
2. Enganche el cable de arranque dentro de la guia de cable (esta guia podria tener un ajuste apretado).
1. Ponga el cortacéspedes al aire libre, sobre una superfi cie lisa y nivelada.
2. Quie la tapa de lienado de aceite. Agregue al motor todo el contenido del recipiente de aceite suministrado. Coloque nuevamente la tapa de llenado de aceite.
3. Quite el tapón del combustible. Después de seguir los tres pasos de las instrucciones que se encuentran en la tarjeta Fresh Start™, acople el cartucho conservador de combustible a la parte inferior del tapón de combustible.
4. Añada gasolina SIN PLOMO limpia y fresca que tenga un octanaje minimo de 87, dejando unos 2.5 cm de espacio hasta la parte superior del tanque que permita la expan-sión del combustible.
5. Vuelva a poner el tapón del combustible y limpie en caso de derrames.
Manual de mantenimiento de la explotación, Leer el operador, y las instrucciones de seguridad.
Cambio rápido 3 en 1 Convierta del modo de trituración a recolección en bolsa a descarga lateral
Convertir a Bolsas
Convertir a descarga lateral
1. Para el modo de trituración, deje en su sitio la cubierta de reciclaje. Asegúrese de que el enchufe mulching está instalado correctamente, con la fl echa apuntando hacia arriba
1. Montar el recolector de césped deslizando la bolsa sobre el conjuncto de la estructura, y sujetándolo con los ganchos de la bolsa.
2. Si bien el levantamiento y la celebración de la puerta trasera abierta, conecte el colector de césped en la parte trasera de la máquina.
3. Asegúrese de los ganchos de ambos lados del gancho marco receptor en la varilla de la puerta trasera.
4. Suelte la puerta trasera (ésta se colocará sobre la parte superior del recolector de césped).
1. Levante la cubierta de reciclaje. Asegúrese de que el enchufe mulching está instalado correctamente.
2. Instale el desviador de descarga lateral sobre la platforma del cortacésped. Verifi que que las lengüetas de la cubierta se fi jan a través de las ranuras de enganche.
3. Suelte la cubierta de reciclaje (está se colocará sobre la parte superior del desviador de descarga lateral).
Control de
cuchillas
Lienado de aceite y
varilla medidora
Cubierta
de reciclaje
Tapa de llenado
de combustible
Mango del cable
de arranque
Ajuste de sltura de corte
Consulte el Manual del Operador para obtener instrucciones sobre cómo iniciar, operar, ajustar o realizar el mantenimiento de la máquina. AVISO: La batería puede requerir de carga antes de su utilización en el cortacésped. Consulte el Manual del Operador para obtener las instrucciones de la batería completa.
1. Deslice el armazón dentro de la bolsa de césped. Verifi que que la manija está enel lado exterior de la bolsa de césped.
2. Sujete los ganchos al costado del armazón. 3. Sujete los ganchos a la parte superior e inferior del
armazón.AVISO: Antes de fi jar la bolsa de recolección de la segadora, el
tapón acolchado debe ser removida, y debe sustituirse tan pronto como se completen las operaciones de ensacado.
En algunas modelos, el defl ector de decarga de montaje lateral se sujeta de manera temporal (para propósitos de envío) a la parte trasera del cortacésped. Antes de ensablar la bolsa de césped, remueva el defl ector de descarga de montaje lateral.
Form NO: 7104079 (Rev. - )
Guía de montaje rápidoCortacéspedes BTXPV22700E autopropulsado
¿Alguna Pregunta?No vuelva a la tienda. Podemos ayudarle.Llame gratuitamente al departmento de servicio al cliente,1-800-743-4115
A
B
C
D
E
F
Montaje del asidero A
Ensambleje de la bolsa de césped B
Instale el mango del cable de arranque C
AVISO: El cortacéspedes es enviado sin aceite dentro del motor. No agregar el aceite resultará en daño del motor.
AVISO: El tanque de combustible tiene una capacidad de menos de 2 litros.
AVISO: NO mexcle el aceite con el combustible.
AVISO: NO utilice combustible E85.
Cómo añadir aceite y combustible D
Convertir el modo de trituración E
F
G
G
H
H
AVISO: El elemento de triturado solo debe demontarse quando se desea el empacado en bolsa, y debe colocarse nuevamete tan pronto como se terminen las operaciones de empacado en bolsa.
Cargador
de
Bateria
Palanca de
tracción
Interruptor de
encendido
Not for Reproduction
