REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...
Transcript of REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...
![Page 1: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/1.jpg)
State of DelawareDELAWARE GEOLOGICAL SURVEYJohn H. Talley, State Geologist
REPORT OF INVESTIGATIONS NO. 77
SIMULATION OF GROUNDWATER FLOW IN
SOUTHERN NEW CASTLE COUNTY, DELAWARE
By
Changming He and A. Scott Andres
University of DelawareNewark, Delaware
2011
![Page 2: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/2.jpg)
State of DelawareDELAWARE GEOLOGICAL SURVEYJohn H. Talley, State Geologist
REPORT OF INVESTIGATIONS NO. 77
SIMULATION OF GROUNDWATER FLOW IN
SOUTHERN NEW CASTLE COUNTY, DELAWARE
By
Changming He and A. Scott Andres
University of DelawareNewark, Delaware
2011
![Page 3: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/3.jpg)
TABLE OF CONTENTS
Page
ABSTRACT ...............................................................................................................................................................................1
INTRODUCTION.....................................................................................................................................................................1
Purpose and Scope ..............................................................................................................................................................1
Previous Work......................................................................................................................................................................1
SIMULATION OF GROUNDWATER FLOW ......................................................................................................................2
Groundwater Flow Model ..................................................................................................................................................2
Additional Hydrologic and Geospatial Data .......................................................................................................................3
Conceptual Model and Model Implementation...................................................................................................................4
Model Input .........................................................................................................................................................................5
Calibration and Sensitivity Analysis ...................................................................................................................................6
Water Budget and Flow Directions .....................................................................................................................................7
Predicted Effects of Increased Pumping .............................................................................................................................9
CONCLUSIONS .....................................................................................................................................................................10
RECOMMENDATIONS ........................................................................................................................................................11
REFERENCES CITED..........................................................................................................................................................11
![Page 4: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/4.jpg)
Page
Figure 1. Location of study area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Figure 2. Locations of pumping and observation wells used in the study. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Figure 3. Conceptual model showing aquifer and confining bed geometries, boundary conditions, and . . . . . . . . . . . . . .groundwater flow directions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
(Figures 4a through 4i are located on Plate 1)
Figure 4a. Elevation of the base of layer 1 (Columbia aquifer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4b. Elevation of the base of layer 2 (Blackbird confining unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4c. Elevation of the base of layer 3 (Rancocas aquifer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4d. Elevation of the base of layer 4 (Armstrong confining unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4e. Elevation of the base of layer 5 (Mt. Laurel aquifer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4f. Elevation of the base of layer 6 (Summit confining unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4g. Elevation of the base of layer 7 (Magothy/Potomac A aquifer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4h. Elevation of the base of layer 8 (Potomac B aquifer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4i. Elevation of the base of layer 9 (Potomac C aquifer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5. Boundary conditions for layer 3 (Rancocas aquifer), layer 5 (Mt. Laurel aquifer), and . . . . . . . . . . . . . . . . . . . .layers 7, 8, and 9 (Potomac aquifers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Figure 6. Constant-head values used for uppermost saturated layer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Figure 7. Relationships between specific capacity and transmissivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
(Figures 8a through 8g are located on Plate 2)
Figure 8a. Calibrated hydraulic conductivity for layer 1 (Columbia aquifer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 8b. Calibrated hydraulic conductivity for layer 2 (Blackbird confining unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 8c. Calibrated hydraulic conductivity for layer 3 (Rancocas aquifer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 8d. Calibrated hydraulic conductivity for layer 4 (Armstrong confining unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 8e. Calibrated hydraulic conductivity for layer 5 (Mt. Laurel aquifer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 8f. Calibrated hydraulic conductivity for layer 7 (Magothy/Potomac A aquifer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 8g. Calibrated hydraulic conductivity for layer 9 (Potomac C aquifer ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 9. Comparison of calculated vs. observed head: steady state. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Figure 10. Results of sensitivity analysis comparing relative changes in simulated flow and head RMS error . . . . . . . . . . .to relative changes in conductance of general-head boundaries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Figure 11. Simulated water budgets - comparison of inflow and outflow rates between aquifers and surface-water . . . . . .boundaries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Figure 12. Predicted difference in head between layer 3 (Rancocas aquifer) and layer 5 (Mt. Laurel aquifer). . . . . . . . . .9
Figure 13. Model computed heads for layer 3 (Rancocas aquifer) and layer 5 (Mt. Laurel aquifer). . . . . . . . . . . . . . . . . .10
Figure 14. Comparison of flow rates from upper aquifers to layer 7 (Magothy/Potomac A aquifer) and flow rates . . . . . .between Potomac aquifers by varying hydraulic conductivity (K) of layer 6 (overlying confining layer) . . . . .11
Figure 15. Predicted differences in head between layer 5 (Mt. Laurel aquifer) and layer 7 . . . . . . . . . . . . . . . . . . . . . . . . . .(Magothy/Potomac A aquifer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Figure 16. Model-computed heads for layers 7, 8, and 9 (Magothy/Potomac A, Potomac B and Potomac C aquifers) . . .12
(Figures 17a through 17e are located on Plate 2)
Figure 17a. Change in head in layer 3 (Rancocas aquifer) due to increased pumping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 17b. Change in head in layer 5 (Mt. Laurel aquifer) due to increased pumping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 17c. Change in head in layer 7 (Magothy/Potomac A aquifer) due to increased pumping . . . . . . . . . . . . . . . . . . . . . .
Figure 17d. Change in head in layer 8 (Potomac B aquifer) due to increased pumping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 17e. Change in head in layer 9 (Potomac C aquifer) due to increased pumping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LIST OF ILLUSTRATIONS
![Page 5: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/5.jpg)
Page
Table 1. Groupings of lithostratigraphic units for groundwater model layers, layer thicknesses, and elevations of layer bottoms. ..............................................................................................................................2
Table 2. Correlation of hydrostratigraphic units between states ...........................................................................................4
Table 3. List of production wells and pumping rates used in steady-state model.................................................................7
Table 4. Model calibration results .........................................................................................................................................8
LIST OF TABLES
Use of trade, product, or firm names in this report is for descriptivepurposes only and does not imply endorsement by the DelawareGeological Survey.
Conversion factors:
Multiply By To obtain
meter (m) 3.28 foot (ft)cubic meter per day (m3/d) 264.17 gallons per day (gal/d)
Acknowledgements
Reviews of the manuscript by Jim Boyle, Tom McKenna, and John Talley
resulted in significant improvements and are gratefully appreciated.
![Page 6: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/6.jpg)
INTRODUCTION
Southern New Castle County (SNCC) and northernKent County (NKC) (Fig. 1) are undergoing rapid develop-ment. The Delaware Population Consortium (2005) esti-mates that the population will more than triple between theyears 2000 and 2030 thereby increasing the total number ofresidents to more than 95,000. The sole source of drinkingwater for residents in this area comes from groundwater, andgroundwater is a major source of water for agricultural andcommercial concerns (Delaware WSCC, 2006).
Recent and projected increases in water demand haveraised concerns about potential impacts on water availabilityand water quality in the aquifers of SNCC and NKC and theeffects of declining groundwater levels on stream flow, wet-lands, and other ecologically sensitive areas. A better under-standing of the hydrogeologic system is essential in makingproper and informed management decisions concerninggroundwater use in this area.
Given the complexity of aquifer characteristics anddevelopment patterns, a numerical groundwater flow modelnot only helps in understanding and conceptualizing the cur-rent groundwater flow system, but also provides a quantita-tive evaluation of changes in groundwater levels under cur-rent and projected water use conditions.
Purpose and Scope
Similar to many flow model studies, the purpose of thiswork was to simulate flow and groundwater levels due topumping, predict changes in flow and groundwater levelsdue to changes in pumping, and evaluate the completeness
and suitability of existing hydrogeologic data. This reportdocuments development of the model, the results of modelcalibration, and analysis of a simulated water budget andsimulated flow directions.
Previous Work
In addition to SNCC and NKC, the study area for dataevaluation included portions of New Castle County north ofthe Chesapeake and Delaware (C&D) Canal, portions ofKent County extending to the Leipsic River, portions ofMaryland extending westward to Chesapeake Bay, andportions of New Jersey extending several miles from theNew Jersey shore of the Delaware River (Fig. 1).
Dugan et al. (2008), the most recent compilation ofexisting hydrogeologic information for the study area, wasthe primary source of hydrologic information for this study.Interested readers are directed to that report for moredetailed descriptions of geologic units and their hydrologicfunctions.
This study divides the Coastal Plain into six aquifers andthree confining units. Further, we used the interpretation ofthree subunits (A, B, and C; Benson and McLaughlin, 2006)(Table 1) within the Potomac that were used in recent mod-eling work by the U.S. Army Corps of Engineers (USACE)(USACE, 2007). These subunits will, in some cases, becollectively referred to as the Potomac aquifers. Because theRancocas and Mt. Laurel aquifers occur at shallower depthsand their hydraulic and chemical properties are suitable forwater supply, they have been the primary source of water fornearly all domestic wells and many public supply wells.
Delaware Geological Survey • Report of Investigations No. 77 1
SIMULATION OF GROUNDWATER FLOW IN
SOUTHERN NEW CASTLE COUNTY, DELAWARE
ABSTRACT
To understand the effects of projected increased demands on groundwater for water supply, a finite-difference,steady-state, groundwater flow model was used to simulate groundwater flow in the Coastal Plain sediments of southern NewCastle County, Delaware. The model simulated flow in the Columbia (water table), Rancocas, Mt. Laurel, combinedMagothy/Potomac A, Potomac B, and Potomac C aquifers, and intervening confining beds. Although the model domainextended north of the Chesapeake and Delaware Canal, south into northern Kent County, east into New Jersey, and west intoMaryland, the model focused on the area between the Chesapeake and Delaware Canal, the Delaware River, and the Maryland-Delaware border. Boundary conditions for these areas were derived from modeling studies completed by others over the past10 years.
Compilation and review of data used for model input revealed gaps in hydraulic properties, pumping, aquifer andconfining bed geometry, and water-level data. The model is a useful tool for understanding hydrologic processes within thestudy area such as horizontal and vertical flow directions and response of aquifers to pumping, but significant data gapspreclude its use for detailed analysis for water resources management including estimating flow rates between Delaware andadjacent states. The calibrated model successfully simulated groundwater flow directions in the Rancocas and Mt. Laurelaquifers as expected from the conceptual model. Flow patterns in the Rancocas and Mt. Laurel aquifers are towards localstreams, similar to flow directions in the Columbia (water table) aquifer in locations where these aquifers are in close hydraulicconnection.
Water-budget calculations and simulated heads indicate that deep confined aquifers (Magothy and Potomac aquifers)receive groundwater recharge from shallow aquifers (Columbia, Rancocas, and Mt. Laurel aquifers) in most of the studydomain. Within shallow aquifers, groundwater moves toward major streams, while in the deep aquifers, groundwater movestoward major pumping centers.
![Page 7: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/7.jpg)
2 Delaware Geological Survey • Report of Investigations No. 77
Barring major pollution problems, it is likely that theseaquifers will continue to be the major groundwater sourcesin this area. Over much of the study area, the Magothy andPotomac aquifers occur hundreds of feet deeper than theRancocas and Mt. Laurel aquifers. Due to the greater cost ofwell construction associated with deeper drilling, only asmall number of public supply wells pump water from theseaquifers.
Spatial models of thicknesses and elevations of hydro-geologic units and hydraulic characteristics reported inDugan et al. (2008) and McLaughlin and Velez (2006) arethe bases of our understanding of the hydrogeologic frame-work of SNCC and NKC. For areas adjacent to our area ofinterest, additional information from groundwater simula-tion reports (USACE, 2007; Martin, 1998; Voronin, 2003;and Drummond, 1998, 2001) were reviewed and reconciledwith those from Dugan et al. (2008). Information includeshydraulic properties and geometries of the tops and bottomsof aquifers and confining beds.
Several local-scale groundwater simulation studies havebeen conducted in this area. Baxter and Talley (1996) con-ducted a steady-state analytical modeling study and estimat-ed water yield by aquifer. Their study did not explicitly con-sider flow between aquifers. Ground Water Associates(1997) conducted a MODFLOW simulation of groundwaterflow in the upper Potomac aquifer and included effects ofnewly constructed and proposed pumping wells. This modeldid not explicitly model flow within the overlying aquifersand assumed vertical flow from overlying units to the upperPotomac aquifer. Using a finite-element model, the USACEconducted a study of groundwater flow in the Potomacaquifers for an area focused on New Castle County north ofthe C&D Canal (USACE, 2007). The model included parts
of SNCC; however, the elements were too large to use in adetailed analysis of conditions in SNCC. Application of theUSACE model results to SNCC is limited because the modelrepresented aquifers and confining beds above the Potomacaquifers as a single layer of elements.
Regional-scale groundwater simulations conducted inthe area include models of the New Jersey Coastal Plain(Martin, 1998; Pope and Gordon, 1998; Voronin, 2003) andof the Maryland and Delaware Coastal Plain (Fleck andVroblesky, 1996). A key element of these models is theposition of the interface between fresh and saline (totaldissolved solids greater than 10,000 mg/L) waters in each ofthe major aquifers. Advanced modeling codes that can sim-ulate density-dependent groundwater flow can explicitly cal-culate the position of this interface; however, this interface istypically represented as a no-flow boundary when density-dependent flow is not simulated. The location of the no-flowboundary can have significant impacts on simulated flowdirections.
SIMULATION OF GROUNDWATER FLOW
Groundwater Flow Model
Groundwater flow was simulated using Visual MOD-FLOW (Schlumberger Water Systems, 2008), a 3D finite-difference groundwater modeling program. This software isan implementation of Modflow-2000, developed by the U.S.Geological Survey (USGS).
Data limitations require that model implementation befairly simplistic. After compilation and review of ground-water-level data for the study area, we found that the distrib-ution of wells having water-level observations extendingover a sufficient length of time is very sparse. There are veryfew data from aquifer tests that could be used to determinestorage coefficient and storativity and only one long-termstreamflow monitoring site exists in the study area. Theavailable hydrologic data are not adequate to support con-struction of a transient, groundwater flow model and imposeserious limitations on implementation and calibration of asteady-state model.
Wells with hydraulic properties determined fromreliable pumping test data are sparse in number and spatialdistribution (Dugan et al., (2008), Drummond (1998),Martin (1998), Voronin (2003), and USACE (2007)).Specific capacity (Sc) data, however, are more widelyavailable (Dugan et al., 2008). To improve initial estimatesof hydraulic conductivity (K) and transmissivity (T), we usedSc to derive hydraulic conductivity from an empiricallydetermined regression relationship between Sc and T.Usually, the correlation is better between log-transformedvalues of T and Sc, and the linear relationship can thus beexpressed as
T = A * Sc B
where A and B are regression coefficients of the power rela-tionship (Rotzoll and El-Kadi, 2008). We used the results ofthis regression analysis, spatial models of aquifer thickness(b), and the relationship between hydraulic conductivity (K)and T (K= T x b) to compute point estimates of K. Thesevalues along with K values from Dugan et al. (2008) were
Figure 1. Location of study area. NNCC = northern New CastleCounty; SNCC = southern New Castle County; NKC = northernKent County. Boxed area is the model domain.
![Page 8: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/8.jpg)
interpolated using the ordinary kriging method in Surfer(Golden Software, 2008) to estimate grids of K values foraquifer units within the study area. The K grids were thenspatially averaged and grouped into conductivity zones(K zones) with similar ranges of values, adapted to the model
grid, and assigned as the initial K values to begintesting and calibration of the model.
The model was calibrated by comparingmodel-predicted heads to heads measured inobservation wells (Fig. 2) and by comparingmodel-predicted water budgets to previous esti-mates of long-term recharge rates (Johnston,1973). Sensitivity analysis is a procedure thatevaluates model response to variations in theinput parameters. In one set of tests, conduc-tance values assigned to general-head boundaries(GHBs) were varied by a factor of four. A sec-ond test evaluated the effects of altering the ver-tical hydraulic conductivity of the confininglayer overlying the Magothy/ Potomac A aquiferon model-calculated water budgets.
To further characterize and quantify flowwithin the model, water-budget zones weredefined for each model layer and for the bound-aries along the edges of the model domain. Theoutput of the calibrated model was used to calcu-late inflow to and outflow from each zone byusing the Zone Budget package of Visual MOD-FLOW (Schlumberger Water Systems, 2008).Because our model is a steady-state model,changes in aquifer storage are not computed.
Additional Hydrologic and Geospatial Data
Groundwater-level data from Delaware were extractedfrom published (Martin and Andres, 2005, 2008) and unpub-lished in-house sources. Additional groundwater-level datafrom adjacent Maryland and New Jersey were extracted fromthe USGS NWIS Web site (http://waterdata.usgs.gov/
Delaware Geological Survey • Report of Investigations No. 77 3
Table 1. Groupings of lithostratigraphic units for groundwater model layers, layer thicknesses, and elevations of layer bottoms. Confiningunit names are those proposed by Dugan et al. (2008). Hydraulic properties of the Potomac aquifers are adapted from USACE (2007).
Figure 2. Locations of pumping and observation wells used in the study.
![Page 9: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/9.jpg)
usa/nwis) and used to determine heads for constant-headboundaries in model cells located in those states.
Groundwater pumping data were obtained from theWater Allocation Branch of the Delaware Department ofNatural Resources and Environmental Control (DNREC)(S. Lovell, written commun.) and supplemented withinformation reported by the Delaware Water SupplyCoordinating Council (2006). Well locations are shown inFigure 2.
Maps produced using Visual MODFLOW were modi-fied for publication using ArcGIS v9.2 (ESRI, 2007). Mapscreated in Visual MODFLOW were exported as x, y coordi-nate pairs along with the values of hydraulic head, elevation,etc. in ASCII format. These data were then converted to
ESRI format grids for display.Smoothing algorithms in ESRI(2007) were used in the finalrendering of the contour lines andcolor fill patterns to reducepixelation. Base map data weredownloaded from the DelawareData MIL (http://datamil.delaware.gov) in February 2009.
Conceptual Model and ModelImplementation
The regional hydrogeologicframework of SNCC has beendefined by a model grid consistingof 400 columns, 320 rows, and 9vertical layers. Each cell hasdimensions of 150 m by 130 m,resulting in a total of 1,152,000cells (681,345 active cells). Themodel consists of a layeredsequence of six aquifers and three
confining units. In general, these units thicken and dip to thesoutheast (Figs. 3, Figs. 4a-4i on Plate 1, and Table 1). Wehave presented thickness data in tabular format because thereis little variation in thickness within most model layers com-pared to the range in thickness of the model layer represent-ing the Potomac C aquifer. Correlations of names of ourmodel units to those used in Maryland (Drummond, 1998,2001) and New Jersey (Martin, 1998; Voronin, 2003) areshown in Table 2.
Because we are using a finite-difference flow modelingcode, individual model layers are required to be continuousover the entire domain (Anderson and Woessner, 1992). Ingeneral, individual model layers correspond to individualaquifers and confining units. However, several of the geo-logic and aquifer units are truncated toward the north andwest, and in some stream valleys. We followed recommen-dations of Reilly (2001) and assigned a minimum thickness(1 m) to areas where the aquifer(s) or confining bed(s) aremissing. The spatial distributions of hydraulic properties ofthese layers are described in a later section.
Layer 7 includes the combined Magothy and Potomac Aaquifers, which are referred to as the Magothy/Potomac Aaquifer and is included in the general category of Potomacaquifers. The Magothy/Potomac A aquifer is simulated as asingle model layer because of the discontinuous nature ofMagothy sands and the absence of data to describe the thick-ness and extent of the intervening confining unit in the studyarea.
Representation of the water-table and surface-waterfeatures in the model is complicated by the fact that cross-cutting relationships between land surface, water table, andhydrogeologic units cause surface-water features (streams,swamps, and marshes) and the water table to intersect thefive uppermost hydrogeologic units and the model layers thatare used to represent them. This is a problem for numericalmodeling because in some areas the water table occurs inhydrogeologic units beneath the Columbia aquifer and the
4 Delaware Geological Survey • Report of Investigations No. 77
Figure 3. Conceptual model showing aquifer and confining bedgeometries, boundary conditions, and groundwater flowdirections. Numbers indicate model layers.
Table 2. Correlation of hydrostratigraphic units between states.
![Page 10: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/10.jpg)
Columbia aquifer is unsaturated. In order to avoid knownproblems with numerical instability and non-convergencein the model caused by unsaturated model cells, we repre-sent the water table as a constant-head layer. In areaswhere the water table occurs below the base of theColumbia aquifer, constant-head nodes representing thewater table were placed in the uppermost saturated layerwhich, depending on location, would be in the Rancocasaquifer or Mt. Laurel aquifer (Figs. 5a and 5b). A similarstrategy was employed to place constant-head nodes rep-resenting bodies of surface water in the proper modellayer.
General-head boundaries (GHB) were used to repre-sent many of the boundaries along the edges of the modeldomain (Figs. 5a-5c). A uniform value of 1000 m2/daywas initially set as conductance of the GHB cells. Thisvalue was changed during calibration.
Head values for GHB cells in the Rancocas (Fig. 5a)and Mt. Laurel aquifers (Fig. 5b), located along the east-ern and western boundaries, were estimated from Martin(1998) and Drummond (1998), respectively. Setting headvalues for GHB cells in the Rancocas and Mt. Laurelaquifers for the southern boundary proved to be problem-atic. With only one observation well in the Rancocasaquifer in the area, head values for the boundary were esti-mated from a few sparsely distributed water-level mea-surements abstracted from well completion reports.
GHB head values for the Potomac aquifers (layers 7,8 and 9) along the northern and eastern boundaries werederived from the models of USACE (2007), Martin(1998), and Voronin (2003). No-flow boundaries weredefined for Potomac aquifers along the western edge ofthe model domain because no data were available to definethe heads, and the distance to the boundary is great enoughto limit boundary effects (Fig. 5c). A no-flow boundary isspecified on the bottom of the model domain to representcrystalline basement rock and overlying saprolite. Ano-flow boundary was set around the edge of the modelfor all confining units (layers 2, 4, and 6).
A no-flow boundary was set on the southern bound-ary of the model for the Potomac aquifers (Fig. 5c) torepresent the occurrence of an interface between saline(total dissolved solids greater than 10,000 mg/L) and freshwaters in the Potomac aquifers as postulated by Meisler(1981) and Pope and Gordon (1998). The interfacebetween fresh and saline water is commonly modeled as ano-flow boundary (Reilly, 2001).
Model Input
Head values for cells representing the water table andsurface-water features were derived from the digital water-table model of Martin and Andres (2005) and fromDrummond (1998) and Martin (1998). These data werethen adapted to the model grid (Fig. 6) and conceptualmodel.
Delaware Geological Survey • Report of Investigations No. 77 5
Figure 5. Boundary conditions for (a) layer 3 (Rancocasaquifer), (b) layer 5 (Mt. Laurel aquifer), and (c) layers 7, 8, and9 (Potomac aquifers).
![Page 11: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/11.jpg)
The results of regression analysis of T and Sc for all theavailable data are shown in Figure 7a, and the results ofregression analysis using data from the Mt. Laurel aquiferare shown in Figure 7b. The spatial distributions of horizon-tal hydraulic conductivity within model layers was deter-mined by gridding observations and estimates of K, spatialaveraging of results into zones of similar K values, and
conditioning by calibration for all nine layers, which areillustrated in Figures 8a - 8g (Plate 2).
Sedimentary deposits typically exhibit anisotropichydraulic properties – specifically, they are more permeablein the horizontal direction than they are in the verticaldirection (Anderson and Woessner, 1992). The magnitude ofanisotropy is poorly understood for the study area. As aresult, an initial value of 10:1 was selected for the startingvertical anisotropy ratio of K (horizontal K : vertical K).This initial anisotropy value was adjusted during the calibra-tion process.
Hydraulic conductivity for layers representing confiningunits (layers 2 and 4) vary from very low values in the south-east to higher values in the northwest. Areas with lower Kvalues represent locations where confining units are thick;areas with higher K values represent locations where an indi-vidual confining unit is missing due to erosional truncationor stratigraphic pinch out. To avoid numerical instability dueto sharp changes of K, several transition zones were added inwhich K values vary gradually (Figs. 8b, 8d).
Simulation of groundwater pumped by wells (Fig. 2)from confined aquifers was limited to those wells havingreported water use in the DNREC water use database (S.Lovell, personal communication). Simulated pumping rates(Table 3) are averages of those reported in this database.Because the Columbia aquifer was modeled as a constant-head boundary, pumping wells located in this layer were notsimulated in our model.
Calibration and Sensitivity Analysis
Model calibration for head falls within acceptableranges, that is, root mean square error is less than 10 percentof the difference between minimum and maximum head(Table 4, Fig. 9). The primary changes made to K duringcalibration were adjustments to values assigned to individualK zones, rather than adjustments to the spatial sizes andshapes of the zones. It is worth repeating that more obser-vation wells in each aquifer are required to improve theaccuracy of the model.
Rigorous model calibration cannot be done with the cur-rent model design and data limitations. A rough check on theability of the model to accurately simulate flow volumes wasdone through evaluations of water budgets. The model-com-puted water budget for the Columbia aquifer, derived fromsumming all water added by constant-head nodes, indicateda recharge rate of 20.6 cm/yr, or roughly 50 to 80 percent ofrecharge rates estimated from hydrograph separation analy-sis (Table 4, Johnston, 1973). The difference betweenpredicted and observed recharge rates may be partially due tothe fact that a constant-head boundary was used to representthe Columbia aquifer. The difference between predicted andobserved recharge rates may also be partially explained bythe specific streams used by Johnston (1973) and uncertain-ty due to estimation procedures. When data becomeadequate to support more sophisticated models, we expectthat flow calibrations can be improved by explicitly comput-ing heads in the Columbia aquifer.
In this study, several simplifications and assumptionsabout boundary conditions and parameter values were made
6 Delaware Geological Survey • Report of Investigations No. 77
Figure 6. Constant-head values used for uppermost saturated layer.
Figure 7. Relationships between specific capacity and transmissiv-ity (a) using all available data, and (b) using data from the Mt.Laurel aquifer.
![Page 12: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/12.jpg)
because of limited data. This has, of course, consequencesfor the accuracy of the results and for the reliability of themodel. To evaluate the sensitivity of the model (e.g., flowdirections and flow rate between different layers) to changesin conductance values of GHBs, conductance values weredecreased by 50 percent below, and increased up to 1,000percent above the calibrated parameter value during the sen-sitivity analysis (Fig. 10). Results indicated that the changesin magnitude of model flux responses were less than thechanges in magnitude applied to GHB conductance values.RMS errors behaved similarly to fluxes.
Water Budget and Flow Directions
Results of water-budget calculations (Fig. 11a) indicatethat there is significant inflow to the Rancocas aquifer andMt. Laurel aquifer from the water-table constant-headboundary, and most inflow occurs where these aquifers are
Delaware Geological Survey • Report of Investigations No. 77 7
Table 3. List of production wells and pumping rates used in steady-state model. Rates are averages reported in DNREC water-use data-base. Note: gpm = gallons per minute.
Figure 10. Results of sensitivity analysis comparing relativechanges in simulated flow and head RMS error to relative changesin conductance of general-head boundaries.
Figure 9. Comparison of calculated vs. observed head: steady state.
![Page 13: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/13.jpg)
located directly beneath and in hydrologic contact with theColumbia aquifer. Water-budget calculations also show thata majority of this flow exits the model through constant-headnodes in the Columbia, Rancocas, and Mt. Laurel aquifers(Fig. 11b), which is consistent with the conceptual model forthe area; however, this finding highlights a shortcoming ofthe model. Because the water-table aquifer is represented asa constant-head boundary, the model cannot predict theeffects of pumping from the Columbia aquifer on flow to andfrom the underlying aquifers.
Due to the interaction between aquifer and confiningbed geometries, topography, bodies of surface water, andpumping wells, groundwater flow directions exhibit complexspatial variability in the vertical direction. Head differencesbetween the Rancocas and Mt. Laurel aquifers illustrate thisfinding (Fig. 12). In general, the Mt. Laurel aquifer isreplenished in the subcrop area in the northern portion of themodel domain in topographically high areas where the con-stant-head water-table boundary is coincident with the Mt.Laurel aquifer or by vertical flow from the Columbia aquiferto the Mt. Laurel aquifer. In areas within stream valleys,groundwater flows upward from the Mt. Laurel aquifer towater-table constant-head boundaries in the Rancocasaquifer or the Columbia aquifer, indicating that the Mt.Laurel aquifer contributes to streamflow. In the southernpart of the model domain, head differences indicate thepotential for upward flow from the Rancocas aquifer to theMt. Laurel aquifer, with the flow rate dependent on the headdifferences and the hydraulic properties of the interveningconfining unit.
Complex interactions between aquifer geometries,topography, bodies of surface water, and pumping wells alsocreate complex spatial variability in horizontal flow direc-tions. Flow directions within the Rancocas and Mt. Laurelaquifers are directed from cells underlying topographicallyhigh areas toward cells representing streams, the C&DCanal, and marshes fringing tributaries to Chesapeake Bayand the Delaware River (Figs. 13a, 13b).
Throughout most of the model domain, predicted headsin the Rancocas and Mt. Laurel aquifers are above sea level.Due to heads in GHB cells, predicted heads in these aquifers
are below sea level in the southeasternmost portion of themodel domain. This prediction cannot be verified becausethe heads below sea level in this area were derived from afew driller-reported water levels abstracted from well com-pletion reports. If the head predictions in the southeasternportion of the model domain are correct, they indicate thepotential for downward flow of salty water from the overly-ing marsh and tidal streams to the Rancocas aquifer. Thisfinding underscores a recommendation from Dugan et al.(2008) for exploratory drilling and new monitoring wells tobe located in this area.
Water-budget results indicate that the GHB cells on theedges of the model domain are the primary source of waterfor the Magothy/Potomac A aquifer rather than vertical leak-age from overlying layers (Figs. 11 and 14). Data are notsufficient to document locations where most of the verticalflow is occurring; however, the maximum head differencesbetween the Mt. Laurel aquifer and the Magothy/Potomac Aaquifer (Fig. 15) are coincident with the area of highest headwithin the Mt. Laurel aquifer (Fig. 13b).
Model simulations show that flow rate between the Mt.Laurel aquifer and the Magothy/Potomac A aquifer is sensi-tive to increases in K of the Summit confining unit (layer 6)(Fig. 14). An increase in the value of vertical K for theSummit confining unit increases the amount of vertical leak-age into the Magothy/Potomac A aquifer from above anddecreases the amount of flow into this aquifer from GHBcells along the northern boundary of the model. Resultsindicate that the source of the added water moving down-ward is the water-table constant-head boundary rather thanother boundary cells (Figs. 11, 14).
The significant dependence of flow rates on vertical Kvalues indicates the need for obtaining data on the hydraulicproperties of the Summit confining unit. If the rate of verti-cal flow is small, then pumping in the study area will induceflow from areas north of the C&D Canal where pumping hasalready caused water levels to be drawn down far below sealevel. If the rate of vertical flow is large, then increasedpumping in the Potomac aquifers will induce flow from theoverlying layers, thus reducing the amount of water availablefor shallower wells and maintaining streamflow.
8 Delaware Geological Survey • Report of Investigations No. 77
Table 4. Model calibration results. Note: min = minimum; max = maximum; water levels measuredin the last ten years were used to calculate minimum, maximum, and average values.
![Page 14: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/14.jpg)
Model-computed water budgets indicate that the vastmajority of water in layers 8 and 9 (Potomac B and Caquifers) is derived from vertical flow from layer 7(Magothy/Potomac A aquifer) (Fig. 11a). The modelpredicts that this water exits the model domain through GHBcells in layer 9 (Fig. 11b). Contour maps of head indicatethat the majority of water is leaving the model domain alongthe northern boundary of the model area (Figs. 16b, c) inlayers 8 (Potomac B) and 9 (Potomac C).
Flow directions in the Magothy/Potomac A aquifer(layer 7; Fig. 16a), are directed toward wells pumping waterfrom that layer. Similar relationships between flow direc-tions and pumping wells are observed in the Potomac B(layer 8) and Potomac C (layer 9) aquifers. Consistent with
findings of USACE (2007) and long-term monitoring data,the model predicts that minimum heads in all of the Potomacaquifers are below sea level over large portions of the areasouth of the C&D Canal. In considering these findings it isimportant to note that GHB conditions for the northernboundary of the model strongly influence flow directions inthe Potomac aquifers.
Predicted Effects of Increased Pumping
The Delaware Water Supply Coordinating Council(Delaware WSCC, 2006) projected that the demand for pub-lic water supply in southern New Castle County will increaseby approximately 170 percent between 2006 and 2030. Tounderstand how this increased pumping may affect ground-water flow and water budgets, we assumed that this increaseddemand will be supplied by existing wells (Fig. 2, Table 3),and simulated the increased water demand by increasingconcurrently the pumping rate for all current productionwells by 170 percent (Table 3). Because it is certain that newwells will be installed to meet the increased demand, andbecause the locations of these new wells cannot be predicted,the results are highly speculative. GHB conditions for thenorthern boundary were not changed for this simulation.
Comparison of predicted water levels during increasedpumping to previous model-simulated results (Figs. 17a-17eon plate 2) indicates that the maximum head decline in theRancocas aquifer will be approximately 2.5 meters (8.2 ft)(Fig. 17a), which occurs at the wells serving the James T.Vaughn Correctional Center located northeast of Smyrna.The maximum head decline (about 4 meters or 13.1 ft) in theMt. Laurel aquifer (Fig. 17b) occurs between Middletownand Odessa, with additional areas of decline coincident withthe wells serving the James T. Vaughn Correctional Centerand an additional area west of Clayton.
Effects of increased pumping in the Potomac aquifersindicate maximum additional drawdown to be in the range of
Delaware Geological Survey • Report of Investigations No. 77 9
Figure 11. Simulated water budgets - comparison of (a) inflow and(b) outflow rates between aquifers and surface-water boundaries.GHB = general head boundary; WT = water table.
Figure 12. Predicted difference in head between layer 3 (Rancocasaquifer) and layer 5 (Mt. Laurel aquifer). Positive value indicateshead value in the Rancocas aquifer is greater than in the Mt. Laurelaquifer.
![Page 15: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/15.jpg)
a few meters (Figs. 17c-17e on Plate 2). Given that there arelittle field data with which to evaluate how reasonable thesepredictions are, and that new wells are likely to be installedby water utilities at additional locations, these results areuseful only for illustrative and discussion purposes, ratherthan planning purposes.
CONCLUSIONS
Water-budget calculations and predicted head differ-ences between aquifers indicated significant flow betweenthe Rancocas, Mt. Laurel, and Columbia aquifers, especiallyin updip areas where the confining unit between the aquifersis thin. Farther to the south, where confining units between
the Rancocas, Mt. Laurel, and Columbia aquifersare thicker, flow paths and water budget calcula-tions indicated that flow is towards the DelawareRiver, a regional hydrologic boundary.
The model predicted head patterns in theMagothy/Potomac A, Potomac B, and Potomac Caquifers that are similar to those in previous model-ing studies. Pumping in the Magothy/Potomac Aaquifer from wells located in southern New CastleCounty has lowered heads and is directing flow tothe pumping center near Delaware City. Pumpingfrom wells in the Potomac B and Potomac Caquifers in New Castle County has lowered heads inthese aquifers both north and south of the canal andcauses flow to be directed north towards northernNew Castle County pumping centers.
Water-budget calculations indicated that there issignificant movement of water from theMagothy/Potomac A aquifer downward to thePotomac B and Potomac C aquifers. The predictedflow of water from the Columbia, Rancocas, and Mt.Laurel aquifers to the deeper Magothy/Potomac A,Potomac B, and Potomac C aquifers is highly depen-dent on the hydraulic properties of the confining bedbetween the Mt. Laurel aquifer and theMagothy/Potomac A aquifer. This finding supportsthe need for hydraulic data from the confining layerand indicates the potential for pumping fromPotomac aquifers to impact groundwater and streamsin southern New Castle County.
Groundwater simulations performed by numeri-cal models are now the state of the practice forprofessional and research assessments of groundwa-ter availability and determination of sustainablewater use for an area. Model predictions are only asgood as the information used to construct andcalibrate models. In this regard, there are severalimprovements to numerical models that could makeresults more useful for water management.
As noted in previous sections, there are very fewlocations in the study area where groundwater - leveland streamflow observations have been made.Without suitable water-level data to compare tomodel output, it is not possible to determine howwell the model simulates flow and head distributionswithin and between multiple aquifers. This is a clear
indication that more monitoring locations are needed.Proposed locations for new wells are described by Dugan et al.(2008).
Groundwater pumping rates used in this model areaverages computed from incomplete water-use records.These data are inadequate for future work that simulatestime-dependent responses of aquifers to seasonal and annualchanges in climate and pumping. Accurate and completewater pumping records for large capacity water wells areneeded to allow any model to simulate field conditions ofhead and flow.
10 Delaware Geological Survey • Report of Investigations No. 77
Figure 13. Model computed heads for (a) layer 3 (Rancocas aquifer) and (b)layer 5 (Mt. Laurel aquifer).
![Page 16: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/16.jpg)
Aquifers in the Potomac Formation provide a large por-tion of water currently being pumped and represent thelargest potential additional source of water for the area, yetdata required to accurately portray the geometry, hydraulicproperties, and head distribution of aquifers and confiningbeds within the model domain are absent. This lack of infor-mation highlights a critical need for additional informationrequired to support planning of future water supplies andwastewater disposal, and management of water-dependentenvironmental resources.
RECOMMENDATIONS
We recommend that the current model continue to bemodified and updated as more data become available. Thegeneral plan for modifications is as follows:
1. Following collection and analysis of additional ground-water level and streamflow data, model the water-tableaquifer as a dynamic layer (e.g., without constant-headboundary condition).
2. Following collection and analysis of additional ground-water level, aquifer hydraulics, and pumping data for theRancocas and Mt. Laurel aquifers, construct a transientmodel to evaluate seasonal and annual climate and pump-ing effects on groundwater and stream flow.
3. Following collection and evaluation of additionalgroundwater level and aquifer hydraulics data foraquifers in the Magothy and Potomac Formations, andhydraulics data for intervening confining units and theoverlying Summit confining unit, reconstruct the modeland conduct steady state simulations.
REFERENCES CITED
Anderson, M. P., and Woessner, W. W., 1992, Applied groundwater modeling: San Diego, Academic Press, 381 p.
Baxter, S. J. and Talley, J. H., 1996, Design, development,and implementation of a ground-water quality monitor-ing network for southern New Castle County, Delaware.Phase II – Evaluation of ground-water availability:Delaware Geological Survey Contract Report 96-01.
Internal stratigraphic correlation of the subsurface PotomacFormation, New Castle County, Delaware, and adjacentareas in Maryland and New Jersey: Delaware GeologicalSurvey Report of Investigations No. 71, 15 p.
Delaware Population Consortium, 2005, New Castle CountyDraft CCED Population Allocations.
Delaware Water Supply Coordinating Council, 2006,Estimates of water supply and demand in southern NewCastle County through 2030: Delaware Water SupplyCoordinating Council, 29 p.
Drummond, D. D., 1998, Hydrogeology, simulation ofground-water flow, and ground-water quality of theupper Coastal Plain aquifers in Kent County, Maryland:Maryland Geological Survey Report of InvestigationsNo. 68, 76 p.
_____, 2001, Hydrogeology of the Coastal Plain aquifer sys-tem in Queen Anne’s and Talbot Counties, Maryland withemphasis on water-supply potential and brackish-waterintrusion in the Aquia aquifer: Maryland GeologicalSurvey Report of Investigations No. 72, 141 p.
Dugan, B. L, Neimeister, M. P., and Andres, A. S., 2008,Hydrologeologic framework of southern New CastleCounty: Delaware Geological Survey Open-File ReportNo. 49, 22 p., 2 pl.
ESRI, 2007, ArcGIS v9.2: Redlands, CA.
Fleck, W.B., and Vroblesky, D.A., 1996, Simulation ofground-water flow of the Coastal Plain aquifers in partsof Maryland, Delaware, and the District of Columbia:U.S. Geological Survey Professional Paper 1404, 41 p, 9plates.
Golden Software, 2008, Surfer v. 8, Golden Colorado.
Delaware Geological Survey • Report of Investigations No. 77 11
Figure 14. Comparison of flow rates from upper aquifers to layer 7(Magothy/Potomac A aquifer) and flow rates between Potomacaquifers by varying hydraulic conductivity (K) of layer 6 (overlyingconfining layer). GHB = general head boundary; WT = water table.
Figure 15. Predicted differences in head between layer 5 (Mt.Laurel aquifer) and layer 7 (Magothy/Potomac A aquifer). Positivevalue indicates head value in the Mt. Laurel aquifer is greater thanthe Magothy/Potomac A aquifer.
![Page 17: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/17.jpg)
Ground Water Associates, 2007, Simulation of groundwater flow in the upper Potomac aquifer of southernNew Castle County: Bridgewater, NJ, Ground WaterAssociates, 18 p, tables, plates.
Johnston, R. H., 1973, Hydrology of the Columbia(Pleistocene) deposits of Delaware: an appraisal ofa regional water-table aquifer: Delaware GeologicalSurvey Bulletin 14, 78 p.
Martin, M., 1998, Ground-water flow in the New JerseyCoastal Plain: U.S. Geological Survey ProfessionalPaper 1404-H, 146 p.
Martin, M. J., and Andres, A. S., 2005, Digital water-table data for New Castle County, Delaware:Delaware Geological Survey Digital Product 05-04.
___, 2008, Analysis and summary of water-table mapsfor the Delaware Coastal Plain: DelawareGeological Survey Report of Investigations No. 73,10 p., 3 pl.
McLaughlin, P. P., and Velez, C. C., 2006, Geology andextent of the confined aquifers of Kent County,Delaware: Delaware Geological Survey Report ofInvestigations No. 72, 40 p., 1 pl.
Meisler, H., 1981, Preliminary delineation of saltyground water in the northern Atlantic Coastal Plain:U.S. Geological Survey Open-File Report 81-71, 12p.
Pope, D. A., and Gordon, A. D., 1998. Simulation ofground-water flow and movement of the freshwater-saltwater interface in the New Jersey Coastal Plain:U. S. Geological Survey Water-ResourcesInvestigation Report 98-4216, 159 p.
Reilly, T. E., 2001, System and boundary conceptual-ization in ground-water flow simulation: Techniquesof Water-Resources Investigations of the U.S.Geological Survey, Book 3, Chapter B8, 30 p.
Rotzoll, K, and El-Kadi, A. I., 2008, Estimatinghydraulic conductivity from specific capacity forHawaii aquifers, USA, Hydrogeology Journal, vol.16, p.969–979.
Schlumberger Water Systems, 2008, Visual Modflow v4.3: Waterloo, Ontario, Canada.
United States Army Corps of Engineers, PhiladelphiaDistrict (USACE), 2007, Groundwater ModelProduction Run report, Upper New Castle County,Delaware: report prepared for the DelawareDepartment of Natural Resources andEnvironmental Control, December, 2006, 44 p.
Voronin, L. M., 2003, Documentation of revisions tothe regional aquifer system analysis model of theNew Jersey Coastal Plain: U. S. Geological SurveyWater-Resources Investigations Report 03-4268,49 p.
12 Delaware Geological Survey • Report of Investigations No. 77
Figure 16. Model-computed heads for layers 7, 8, and 9(Magothy/Potomac A, Potomac B, and Potamac C aquifers,respectively).
![Page 18: REPORT OF INVESTIGATIONS NO. 77 SIMULATION OF GROUNDWATER ...](https://reader034.fdocuments.net/reader034/viewer/2022051315/627a159921510650b13ec11c/html5/thumbnails/18.jpg)
Delaware Geological SurveyUniversity of DelawareNewark, Delaware 19716