REPLACEMENT WHEEL CATALOG - Easylift Systems,...

REPLACEMENT PARTS INC. OHIO LOOP

DONALDSON INDUSTRIAL AIRPARK GREENVILLE, SC 29605

(864)299-3000 * FAX 299-3021 www.replacement-partsinc.com

REPLACEMENT WHEEL CATALOG

http://www.replacement-partsinc.com/

Owner

Logo Only

Owner

Logo Only

REPLACEMENT PARTS INC. 13 OHIO LOOP

GREENVILLE SC 29605 (864)299-3000*FAX 299-3021

Welcome! This catalog is presented to you with our compliments. We hope that you find it useful. The enclosed information is representative of the parts that we handle, but it by no means covers the full scope of our ability to serve your needs in material handling. We specialize in locating or reproducing obsolete, foreign, or hard to find parts. Our research is aided by our participation in a computerized national network. We also refurbish all types of hoists, cabs, and monotractors. Please take a few moments to look over our catalog. It would be a pleasure to discuss with you your needs and demonstrate to you where your cost savings may lie. Replacement Parts for the following manufactures. 1. Louden 2. Cleveland Tramrail 3. Spanmaster 4. Twin City 5. American Monorail 6. P&H (Not in catalog) Contact: John Ludwig Sincerely, ��

John E. Ludwig President

Established 1986 Replacement Parts Inc.

Owner

Logo Only

REPLACEMENT PARTS INC. 13 Ohio Loop

Greenville, SC 29605 (864)299-3000 FAX(864)299-3021

RETREAD SERVICE FOR INDUSTRIAL MOLDED ON WHEELS

POLYURETHANE: Ideally suited to conditions requiring high load capacities,

pulling ease, resistant to oil, solvents, and extremely low temperatures.

Owner

Logo Only

GENERAL DIMENSIONS HUB DIMENSIONS Flange Style: _______ Fig. 1 (double flange) Hub Style: _____Fig. 4 (check one) (Check One) _______ Fig. 2 (single flange) _____Fig. 5 _______ Fig. 3 (plain tread) F. Hub Diameter________________________(in.) A. Tread Diameter __________(in.) G. Length from Centerline _______________(in.) B. Overall Diameter _________(in.) H. Length from Centerline _______________(in.) C. Width Over Flanges________(in.) J. Total Hub Length ____________________(in.) D. Tread Contour: (a) straight tread____ K. Bore Size: (a) Finished ________________(in.) (b) tapered tread____(degrees) (b) Rough _________________(in.) (c) radius tread _____(in. radius) M. Inside Keyway: Size _____(in.), No._________ (d) crown tread_____(in. radius) N. Outside Keyway:Size_____(in.), No._________ E. Tread Width __________”, or Rail Size _____#”. P. Diameter of Finished Hub Extension_______(in.) Or Rail Head Width _______”. Q. Length of Finshed Hub Extension ________(in.) Quantity Needed: Drivers______________________________Idlers_________________________ CHECK FOLLOWING ITEMS REQUIRED: ___Counterbores: Diameter____________________(in.), Depth____________(in.), Number__________ ___Setscrews: Size __________________________(in.), Number _______________________________ ___Drilled or Tapped Holes: Size ______________(in.), Depth_____________(in.), Number__________ Location (B.C.) ________________________________________________________________ REMARKS: _________________________________________________________ _________________________________________________________ _________________________________________________________

REPLACEMENT PARTS INC.

INDEX

1. LOUDEN PAGES 1- 11 2. CLEVELAND TRAMRAIL PAGES 12 - 25 3. SPANMASTER PAGES 26 - 32 4. TWIN CITY PAGES 33 - 45 5. AMERICAN MONORAIL PAGES 46 - 90

Page��1

REPLACEMENT PARTS INC

Replacement Wheels Designed to fit Louden trolleys 403.7502, and 403.15004 (flangeless wheel) on 3.33" track. Regreasable or Nonregreasable wheel assembly Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part# WA0589B4 ( 9" Dia )

REF: Louden Part Number #28-0589

Page��2

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Louden trolley 403.5052 (flangeless wheel) on 3.33" track. Regreasable or Nonregreasable wheel assembly Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part# WA0595B4 ( 4.5 Dia. ) REF: Louden Part Number #28-0595

Page��3

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Louden trolleys 402.372 and 402.754 (flanged wheel) on 2" and 3.33 track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part# WA0875B4 ( 3" Dia ) REF: Louden Part Number #28-0875

Page��4

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Louden trolleys 403.5002 and 403.10004 (flanged wheel) on 3.33 track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part# WA0593B4 ( 4.5" Dia ) REF: Louden Part Number #28-0593

Page��5

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Louden trolley 403.20054 (flangeless wheel) on 3.33" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part# WA0665B4 ( 9" Dia )

REF: Louden Part Number #28-0665

Page��6

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Louden trolleys 402.1502,402.3004,402.6008 and 402.3024 (flanged wheel) on 2" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part# WA0877B4 ( 4" Dia. ) REF: Louden Part Number #28-0877

Page��7

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Louden trolleys 403.1502,403.3004,403.6008 and 403.3024 (flanged wheel) on 3.33 track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precession ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part# WA0878B4 ( 4" Dia. ) REF: Louden Part Number #28-0878

Page��8

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Louden trolleys 402.1552LF,and 403.1552LF (flangeless wheel) on 2" and 3.33" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part# WA0879B4 ( 4" Dia ) REF: Louden Part Number #28-0879

Page��9

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Louden trolley 403.2552LF (flangeless wheel) on 3.33" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part# WA0881B4 ( 4.5 Dia. ) REF: Louden Part Number #28-0881(NEW PART# 28-0661)

Page��10

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Louden trolleys 403.2502,403.5004,and 403.1008 (flanged wheel) on 3.33" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part# WA0882B4 ( 4.5 Dia. ) REF: Louden Part Number #28-0882

Page��11

REPLACEMENT PARTS INC Replacement Drive Tire Designed to fit Louden Monorails and cranes. Replacement Parts 9" X 2.5" is a solid neoprene or rubber tire. Ref: Used on a Monotractors and Crane Drive. Replacement Parts Part Number: TK567B3 REF: Louden Monorail Part # 260536 (PF4487)

Page��12


Replacement Wheels Designed to fit Cleveland Tramrail Carrier Head HA 255(flanged wheel) on 2100 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part # WA2200B4 REF: Cleveland Tramrail Number - 2-02200-000

Page��13


Replacement Wheels Designed to fit Cleveland Tramrail Carrier Head H1/4 (flanged wheel) on 2100 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part #WA860110B4 REF: Cleveland Tramrail Number - 1-08601-010

Page��14


Replacement Wheels

Designed to fit Cleveland Tramrail Carrier Head H-3/8 - HR-3/8 (flangeless wheel) on 2100 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part #WA860142B4 REF: Cleveland Tramrail Number - 1-08601-420

Page��15


Replacement Wheels

Designed to fit Cleveland Tramrail Carrier Head H-3/8 - HR-3/8 (flanged wheel) on 2100 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part #WA860162B4 REF: Cleveland Tramrail Number - 1-08601-620

Page��16


Replacement Wheels Designed to fit Cleveland Tramrail Carrier Head H1/4 (flangeless wheel) on 2100 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part #WA860131B4 REF: Cleveland Tramrail Number - 1-08601-310

Page��17

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Cleveland Tramrail Carrier Head H1/2 (flanged wheel) on 2100 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part #WA17162B4 ( 5" Dia. ) REF: Cleveland Tramrail Number - 1-17162-300

Page��18


Replacement Wheels Designed to fit Cleveland Tramrail Carrier Head ES and ESR (flanged wheel) on 2100 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part #WA221210B4 REF: Cleveland Tramrail Number - 2-02212-100

Page��19

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Cleveland Tramrail CH Tractor (flangeless wheel) on 2100 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part #WA17241B4 REF: Cleveland Tramrail Number - 1-17241-220

Page��20

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Cleveland Tramrail Trailer Head R (flanged wheel) on 2100 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part #WA3212B4 REF: Cleveland Tramrail Number - 2-03212-000

Page��21

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Cleveland Tramrail Carrier Head HR-11/2 (flangeless wheel) on 31/4 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part #WA20217B4 REF: Cleveland Tramrail Number - 1-20217-310

Page��22


Replacement Wheels Designed to fit Cleveland Tramrail Carrier Head K-7 & RA (fl angeless wheel) on 31/4 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part #WA19111B4 REF: Cleveland Tramrail Number - 1-19111-000

Page��23

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Cleveland Tramrail Carrier Head WTD (flanged wheel) on 41/2 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part #WA23871B4 REF: Cleveland Tramrail Number - 1-23871-000

Page��24

REPLACEMENT PARTS INC Replacement Pinion Shaft Designed to fit Cleveland Tramrail WA Drive (Pinion Shift) on 3.33" track. Replacement Parts Pinion Shafts are made from high strength steel or, per customer's specifications and the Gear teeth are induction hardened to Rockwell 45 to 50. The Shafts End are remachined after Gear teethes have been heat treated to assure proper concentricity. Replacement Parts New Part # PS17202B5 REF: Cleveland Part Number - 1-17202-000

Page��25

REPLACEMENT PARTS INC Replacement Drive Wheel Designed to fit Cleveland Tramrail T & WA Drives (flangeless wheel) on 3.33" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part # DWA2222B4( 5" Dia. ) REF: Cleveland Part Number - 2-02222-200

Page��26


Replacement Wheels

Designed to fit Spanmaster trolleys 16-100A,16-100J,16-100K and 16-100L (flanged wheel) on 100 and 200 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling.

Replacement Parts Part# WA16100B4 ( 4" Dia. )

REF: Spanmaster Part Number #16-100E

Page��27


Replacement Wheels


Replacement Parts Part# WA16101B4 ( 5" Dia. )

REF: Spanmaster Part Number - 16-101E

Page��28


Replacement Wheels


Replacement Parts Part# WA16102B4 (5" Dia. )


Page��29


Replacement Wheels Designed to fit Spanmaster trolleys 16-103A,16-103J,16-103K and 16-103L (flangeless wheel) on 100 and 200 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part# WA16103B4 ( 5" Dia. )

REF: Spanmaster Part Number #16-103E

Page��30


Replacement Wheels Designed to fit Spanmaster trolleys 16-104A,16-104K and 16-104L (flanged wheel) on 100 and 200 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part# WA16104B4 ( 6.5" Dia. )


Page��31


Replacement Wheels Designed to fit Spanmaster trolleys 16-105A,16-105K and 16-105L (flangeless wheel) on 100 and 200 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part# WA16105B4 ( 6.5" Dia )


Page��32


Replacement Wheels Designed to fit Spanmaster trolley 16-109A,(flangeless wheel) on 100 and 200 series track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part# WA16106B4


Page��33


Replacement Wheels Designed to fit Twin City Trolleys 2T-750-2, 2T-1150-4 2T-850-2 and 2T-1200-4 (flanged wheel) on 2" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part # WA123B4

REF: Twin City Part Number - W123

Page��34


Replacement Wheels Designed to fit Twin City Trolleys 2T-2000-2, 2T-2800-4 (flanged wheel) on 2" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part#WAA164B4

REF: Twin City Part Number - W164F

Page��35


Replacement Wheels Designed to fit Twin City Trolleys 2T-2000-2SR, 2T-2800-4SR (flangeless wheel) on 2" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part #WA270B4

REF: Twin City Part Number - W164FA

Page��36


Replacement Wheels Designed to fit Twin City Trolleys 2T-3000-2, 2T-4000-4 (flanged wheel) on 2" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part #WAE539B4


Page��37


Replacement Wheels Designed to fit Twin City Trolleys 3T-750-2, 3T-1150-4 (flanged wheel) on 3.25" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part #WA124B4

REF: Twin City Part Number - W124A

Page��38


Replacement Wheels Designed to fit Twin City Trolleys 3T-2700-2SR, 3T-5400-4SR (flangeless wheel) on 3.25" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part #WA2840B4

REF: Twin City Part Number - W284FA

Page��39

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Twin City Trolleys 3T-4200-2, 3T-8400-4 (flanged wheel) on 3.25" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part # WAMA7B4 REF: Twin City Part Number - W7

Page��40


Replacement Wheels Designed to fit Twin City Trolleys 3T-4200-2SR, 3T-8400-4SR (flangeless wheel) on 3.25" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part # WAMA57-7B4 REF: Twin City Part Number - W57-7

Page��41

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Twin City Trolleys 3T-6600-2, 3T-13200-4 (flanged wheel) on 3.25" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part # WAME20B4 REF: Twin City Part Number - W20

Page��42

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Twin City Trolleys 3T-6600-2SR, 3T-13200-4SR (flangeless wheel) on 3.25" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part # WAME192B4 REF: Twin City Part Number - W -192-4

Page��43

REPLACEMENT PARTS INC Replacement Wheels Designed to fit Twin City Trolleys 3T-9000-2SR, 3T-18000-4SR (flangeless wheel) on 3.25" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts New Part # WA10192B4 REF: Twin City Part Number - W -10192

Page��44

REPLACEMENT PARTS INC Replacement Drive Tire Assembly Designed to fit Twin City cranes. Replacement Parts drive tires are bonded rubber to a cast iron rim or, per customer's specifications. The drive tire hub bores are 1 1/2" and 1 3/8". Replacement Parts Part Number: DTA1240B1


Page��45

REPLACEMENT PARTS INC Replacement Drive Tire Assembly Designed to fit Twin City cranes. Replacement Parts drive tires are bonded rubber or polyurethane bonded to a cast iron rim or, per customer's specifications. The drive tire hub bores are 1 1/2" and 1 3/8". Replacement Parts Part New Number # DTA1040B4


Page��46


Replacement Wheels

Designed to fit American Monorail Trolleys 820162004,820142004,820179004, (flanged wheel 4" Dia.) on 2" track with removable bearings. Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WAA164B4( 4" Dia.)

REF: American Monorail Part Number # 8201640004

Page��47

REPLACEMENT PARTS INC Replacement Wheels Designed to fit American Monorail Trolley 820270004,820275004,820273004, (flangeless wheel 4" Dia.) on 2" track with removable bearings. Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WAA270B4 ( 4" Dia.) REF: American Monorail Part Number #820270004

Page��48


Replacement Wheels

Designed to fit American Monorail Trolley 820521009 (flanged wheel) on 2" track. Regreasable or Nonregreasable wheel assembly Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WAE539B4 ( 5.5" Dia.) REF: American Monorail Part Number #820539004

Page��49

REPLACEMENT PARTS INC �

� Replacement Wheels �

Designed to fit American Monorail Trolley 16001004 (flanged wheel 4.5" Dia.) on 325" track. Regreasable or Nonregreasable wheel assembly Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WA28001B4 ( 4.5" Dia ) REF: American Monorail Part Number #280010004

Page��50

REPLACEMENT PARTS INC Replacement Wheels Designed to fit American Monorail Trolley 160030004 (flanged wheel 5" Dia.) on 325" track. Regreasable or Nonregreasable wheel assembly Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WA28003B4( 5" Dia.) REF: American Monorail Part Number #280030004

Page��51

REPLACEMENT PARTS INC Replacement Wheels Designed to fit American Monorail Trolley 160070004 (flanged wheel 5" Dia.) on 325" track. Regreasable or Nonregreasable wheel assembly Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WA28007B4( 5" Dia.) REF: American Monorail Part Number #280070004

Page��52

REPLACEMENT PARTS INC Replacement Wheels Designed to fit American Monorail Trolley 160170004 (flangeless wheel 9" Dia.) on 325" track. Regreasable or Nonregreasable wheel assembly Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WA28017D4 ( 9" Dia.) REF: American Monorail Part Number #280170004

Page��53


Page��54


Page��55

REPLACEMENT PARTS INC Replacement Wheels Designed to fit American Monorail A Drive on 325" track. Regreasable or Nonregreasable drive wheel assembly Replacement Parts drive wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The drive wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # DWA28027B4 ( 5" Dia.)

REF: American Monorail Part Number #280270004

Page��56


Replacement Wheels

Designed to fit American Monorail Trolley 160350004 (flangeless wheel 5" Dia.) on 325" track with Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WA28035D4 ( 5" Dia. ) REF: American Monorail Part Number #280350004 ( 5" DIA.)

Page��57


Replacement Wheels

Designed to fit American Monorail Trolley 160370004 (flangeless wheel 6.5" Dia.) on 325" track with Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WA28037D4 (6.5 Dia.) REF: American Monorail Part Number #280370004 ( 6.5" DIA.)

Page��58


Replacement Wheels

Designed to fit American Monorail Trolley 160400004 (flangeless wheel 6.5" Dia.) on 325" track with Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WA28039D4 (6.5 Dia.) REF: American Monorail Part Number #280390004 ( 6.5" DIA.)

Page��59

REPLACEMENT PARTS INC Replacement Wheels Designed to fit American Monorail A or B Drive on 325" track. Regreasable or Nonregreasable drive wheel assembly Replacement Parts drive wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The drive wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # DWA28041B4 ( 6.5" Dia.)


Page��60

REPLACEMENT PARTS INC Replacement Wheels Designed to fit American Monorail C Drive on 450" track. Regreasable or Nonregreasable drive wheel assembly Replacement Parts drive wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The drive wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # DWA28046B4 ( 9" Dia.) REF: American Monorail Part Number #280460004

Page��61

REPLACEMENT PARTS INC Replacement Wheels Designed to fit American Monorail A or B Drives (Pinion Shift) on 325" track. Replacement Parts Pinion Shafts are made from high strength steel or, per customer's specifications and the Gear teeth are induction hardened to Rockwell 45 to 50. The Shafts End are remachined after Gear teethes have been heat treated to assure proper concentricity Replacement Parts Part # PS16027B82 ( A Drive.) Replacement Parts Part # PS16028B91 ( B Drive.)

REF: American Monorail Part Number #160270823/160280913

Page��62

REPLACEMENT PARTS INC Replacement Wheels Designed to fit American Monorail AA Drive on 2" or 325" track. Regreasable or Nonregreasable drive wheel assembly. Replacement Parts drive wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The drive wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # DWA28044B4 ( 4.5" ) REF: American Monorail Part Number #280440004

Page��63

REPLACEMENT PARTS INC Replacement Wheels Designed to fit American Monorail Trolley 840005004 (flanged wheel) on 4" track Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WAMA7B4 ( 5" Dia. )


Page��64


Replacement Wheels

Designed to fit American Monorail Trolley 840002004 (flanged wheel 4.5 Dia.) on 4" track Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WAMA17B4 ( 4.5" Dia. ) REF: American Monorail Part Number #840017004

Page��65

REPLACEMENT PARTS INC Replacement Wheels Designed to fit American Monorail Trolley 840057004 (flangeless wheel) on 4" track Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WAMA57-7B4 ( 5" Dia.) REF: American Monorail Part Number #840057074

Page��66


Replacement Wheels

Designed to fit American Monorail Trolley 840057004 (flangeless wheel 5" Dia.)on 4" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WAMA83C4 ( 5" Dia. )


Page��67

REPLACEMENT PARTS INC Replacement Wheels Designed to fit American Monorail Trolley 840108594 (flanged wheel) on 4" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WAME20B4 ( 6.5" Dia. ) REF: American Monorail Part Number #840020004

Page��68

REPLACEMENT PARTS INC Replacement Wheels Designed to fit American Monorail Trolley 840192004 (flangeless wheel) on 4" track with removable bearings. Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WAME192B4 ( 6. 5" Dia.) REF: American Monorail Part Number #840192044

Page��69

REPLACEMENT PARTS INC Replacement Wheels Designed to fit American Monorail Trolley 84019204 (flangeless wheel) on 4" track with removable bearings. Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WAME192B7 REF: American Monorail Part Number #840192044

Page��70

REPLACEMENT PARTS INC Replacement Wheels Designed to fit American Monorail Trolley 840204004 (flangeless wheel 6.5 Dia.)on 4" track. Regreasable or Nonregreasable wheel assembly. Replacement Parts wheels are made from high strength steel or, per customer's specifications and the treads and flanges are induction hardened to Rockwell 45 to 50. The wheel bearing bores are remachined after the wheels have been heat treated to assure proper concentricity. High quality precision ball or roller bearings are used on a machined steel axle to assure long life and easy rolling. Replacement Parts Part # WAME204-15D4 (6.5" Dia. ) REF: American Monorail Part Number #840204154

Page��71

REPLACEMENT PARTS INC Replacement Tire And Hub Assembly Designed to fit American Monorail Cranes and Monotractors on 4" track. Replacement Parts 12" x 4" x 8" Tire hub assembly is a solid rubber tire on a steel rim and pressed on a steel hub. Ref: Used on MV30 Monotractors and Crane Drives Replacement Parts Part # HME221B45 REF: American Monorail Part Number #840221424

Page��72

REPLACEMENT PARTS INC Replacement Drive Tire Assembly Designed to fit American Monorail Cranes and Monotractors on 2",325 track. Replacement Parts 12"X 3" Tire assembly is a solid rubber with a hub and rim that are pressed on. Comes with 1 3/8" or 1 15/16" Bore. Ref: Used on V2304 Monotractors and Crane Drives REF: American Monorail Part Number #NONE

Page��73

REPLACEMENT PARTS INC Replacement Drive Tire Hub Designed to fit American Monorail 12" X 3" tire. Replacement Parts Tire hub comes with 1 3/8" or 1 15/16" bore. Ref: Used on V2304 Monotractors and Crane Drives Replacement Parts Part# HME662B5 REF: American Monorail Part Number #E662-4

Page��74

REPLACEMENT PARTS INC Replacement Drive Tire Rim Designed to fit American Monorail 12" X 3" tire. Ref: Used on V2304 Monotractors and Crane Drives Replacement Parts Part# RMV2256B5 REF: American Monorail Part Number #822256175

Page��75

REPLACEMENT PARTS INC Replacement Drive Tire Flange Designed to fit American Monorail Drive Tire 12" x 4" on 4" trac k. Replacement Parts tire flange comes with a 1 15/16" bore. Ref: Used Crane Drive Tire THAME221B42. REF: American Monorail Part # 840221205

Page��76

REPLACEMENT PARTS INC Replacement Drive Tire Hub Designed to fit American Monorail Drive Tire 12" X 3" on 3.25 or 4" track. Replacement Parts tire hub comes with 1 3/8" bore. Ref: Used Crane Drive (Note: see plate 139)

REF: American Monorail Part # 8402210335

Page��77

REPLACEMENT PARTS INC Replacement Drive Tire Hub Designed to fit American Monorail Drive Tire 12" X 4" on 4" trac k. Replacement Parts tire hub comes with a 1 3/8" bore. Ref: Used on Crane Drive Tire THAME221B42. REF: American Monorail Part # 840221445

Page��78

REPLACEMENT PARTS INC Replacement Collector Shoes Designed to fit American Monorail cranes. Replacement Parts Collector Shoes are rated at 50 amps based on continuous service. Collector shoes are used to transmit electrical power from a stationary system to moving cranes and trolleys. Ref: Used on Monotractors, Monorails, Cranes and Hoist. Replacement Parts Part Number: CSH988B3 REF: American Monorail Part Number - 820988035

Page��79

REPLACEMENT PARTS INC Replacement Drive Tire Designed to fit American Monorail cranes. Replacement Parts 12"X 4" X 8" is a solid rubber tire on a steel rim. Ref: Used on a MV30 Monotractors and Crane Drives. Replacement Parts Part Number: TMV30B1 REF: American Monorail Part # 840030013

Page��80

REPLACEMENT PARTS INC Replacement Tire Hub Designed to fit American Monorail Cranes and Monotractors on 4" track. Replacement Parts 12" x 4" x 8" Tire hub( Part # HME221B45) Ref: Used on MV30 Monotractors and Crane Drives REF: American Monorail Part Number #840221455

Page��81

REPLACEMENT PARTS INC Replacement Drive Tire Designed to fit American Monorail cranes. Replacement Parts 8" X 2.50" is a solid rubber tire. Ref: Used on a V2302 Monotractors only. Replacement Parts Part Number: T87621B3 REF: American Monorail Part Number - 000876213

Page��82

REPLACEMENT PARTS INC Replacement Insulator Head Designed to fit American Monorail Collector Assemblies. MH81 short, MH82 long. H988short, H989 long, H987 turned up collector. REF: American Monorail Part Number #820988023

Page��83

REPLACEMENT PARTS INC Replacement Collector Shoes Designed to fit American Monorail cranes. Replacement Parts Collector Shoes are rated at 50 amps based on continuous service. This Collector shoe is used on Bare Bar only and is used to transmit electrical power from a stationary system to moving cranes and trolleys. Ref: Used on Monotractors, Monorails, Cranes and Hoist. Replacement Parts Part Number: CSMH55B4 REF: American Monorail Part Number - 840055043

Page��84


Replacement Intermediate End Stop Designed to fit American Monorail MD1 (4") Rail. Replacement Parts Part No. ESMD3B4

Page��85

REPLACEMENT PARTS INC Replacement Collector Bracket Designed to fit American Monorail Railmaster Cranes. Replacement Parts Collector Bracket is used with MH 48-5 Collector Shoe. (for bare bar only) The Collector Bracket is cast from high strength Ductile Iron. Replacement Parts Part Number: CBMH48B1 REF: American Monorail Part Number - MH48-1

Page��86

REPLACEMENT PARTS INC Replacement Collector Shoes Designed to fit American Monorail cranes. Replacement Parts Collector Shoes are rated at 50 amps based on continuous service. This Collector shoe is used on Bare Bar only and is used to transmit electrical power from a stationary system to moving cranes and trolleys. Replacement Parts Part Number: CSMH48B5 REF: American Monorail Part Number - 840048053

Page��87

REPLACEMENT PARTS INC Replacement Side Guide Roller Bolt Designed to fit American Monorail cranes. Replacement Parts Side Guide Roller Bolt is used with The Side Guide Roller #SGR45399. Ref: Used on Monotractors, Monorails, Cranes and Hoist with flangeless wheels. Replacement Parts Part Number: BME204B5 REF: American Monorail Part Number - ME204-5

Page��88


Replacement Side Guide Roller This side guide roller is manufactured from high strength steel. The outer race and inner races are hardened to Rockwell 58, and also high quality precision ball bearings are used. This guide roller is lubricated with GS-19 high temperature grease having an operating rang of 500 degrees. F. This grease exhibits resistance to corrosion, salt water, fresh water, chlorine, acid environments, and heat. This allows minimum wear, prolonged bearing life and maximum corrosion protection. This roller can also be used as a Sealed or Lubricated roller due to it design. This Side Guide Roller can be used as a replacement for American Monorail, Twin City Monorail and Spanmaster Side Guide Rollers. Replacement Parts: Part No.SGR45399

REF: American Monorail Part Number - ME204-17 or -24

Page��89

REPLACEMENT PARTS INC Replacement Drive Tire Designed to fit American Monorail cranes. Replacement Parts Tire 12" X 3" is a solid rubber tire. Ref: Used on a V2304,MV2256,V2256 Monotractors and crane drives. Replacement Parts Part Number: TV2300B


Page��90

REPLACEMENT PARTS INC Replacement Wheel Shaft Assembly Designed to fit American Monorail MV30 Monotractor to run on 4" rai l. Replacement Parts Wheel Shaft assembly is made from high strength steel also high quality precision tapered bearings are used on a machined steel shaft to assure long life. Replacement Parts Part Number: WSAMV30B4

REPLACEMENT WHEEL CATALOG - Easylift Systems,...

Documents

Transcript of REPLACEMENT WHEEL CATALOG - Easylift Systems,...