Greg RECALL

Greg RECALL

sam714-921-9095

sam 714-921-6422

Command SetsBK models 1696/1697/1698 August 2004

BLUE – Input CommandRED – Return Data from Power Supply PS = Power SupplyCommand Code Description

SESS

[OK] [CR]

Disable front panelkeypad and make PS toRemote Mode

ENDS

[OK] [CR]

Enable front panel keypadand make PS to exitRemote Mode

CCOM {000-255}

[OK] [CR]

Change RS-232/RS485 = 0 -> RS-232 = 1 -> RS-485

GCOM

[RS] RS485 Address [###] [CR][OK] [CR]

Get the RS-485 address

GMAX

Voltage [???] Current [???] [CR][OK] [CR]

Get maximum voltage andcurrent of PS

GOVP

Voltage [???] [CR][OK] [CR]

Get Upper Voltage Limitof PS

GETD

Voltage [????] Current [????] [0] [CR][OK] [CR]Voltage [????] Current [????] [1] [CR][OK] [CR]

Get Voltage & Currentreading from PS

PS in CV mode

PS in CC mode

GETS

Voltage [???] Current [???] [CR][OK] [CR]

Get Voltage & Current SetValue from PS

GETM

Memory 1 Voltage [???] Current [???] [CR]Memory 2 Voltage [???] Current [???] [CR]

. . . . .

. . . . .

. . . . .Memory 9 Voltage [???] Current [???] [CR][OK] [CR]

Get All Preset MemoryValues from PS

GETM location {1-9}

Voltage [???] Current [???] [CR][OK] [CR]

Get Memory fromSpecific Preset of PS

GETP

Program 00 Voltage [???] Current [???] Minute [??] Second [??] [CR]Program 01 Voltage [???] Current [???] Minute [??] Second [??] [CR]

. . . . . . .

. . . . . . .

. . . . . . .Program 19 Voltage [???] Current [???] Minute [??] Second [??] [CR][OK] [CR]

Get all the Timed ProgramMemory of PS

GETP program {00-19}

Voltage [???] Current [???] Minute [??] Second [??] [CR][OK] [CR]

To Get Anyone TimedProgram Memory from 20Steps Program of PS

GPAL [CR]

Reading voltage [####] V [ON]Reading current [####] A [ON]Reading watt [####] W [ON]Timer minute [####] second [##] timer [ON] colon [ON] m [ON] s [ON]Setting voltage [###] V-const [ON] V-bar [ON] V [ON]Setting current [###] I-Const [ON] I-bar [ON] A [ON]Program [#] Program [ON] P-bar [ON]SETTING [ON] Key lock [ON] Key open [ON] FAULT [ON] Output on[ON]Output off [ON] Remote [ON] [CR][OK] [CR]

Get LCD DisplayInformation

VOLT voltage {010-XXX}

[OK] [CR]

Set Voltage LevelXXX-Max. Output RatingVoltage = XX.X VCurrent = X.XX V

CURR current {001-XXX}

[OK] [CR]

Set Current Level

SOVP voltage {010-XXX}

[OK] [CR]

Set Upper Voltage Limitof PS

SOUT 0

[OK] [CR]

Disable Output of PS

SOUT 1

[OK] [CR]

Enable Output of PS

PROM location {1-9} Voltage {010-XXX} Current {001-XXX}

[OK] [CR]

Set Voltage and Currentvalues of Preset Memory

PROP location {00-19} Voltage {010-XXX} Current {001-XXX} Minute {00-99} Second {00-59}

[OK] [CR]

Set Voltage, Current andTime period of TimedProgram

RUNM location {1-9}

[OK] [CR]

Recall Preset Memory 1-9

RUNP times {0000-9999}

[OK] [CR]

Run Timed Program(0000 = run infinite times)

STOP

[OK] [CR]

Stop Timed Program

NOTES:{ }- command data, [ ] - return data, [OK] = "OK", [CR] = 0dh???? = 30h, 30h, 30h, 30h - 39h, 39h, 39h, 39h (4 bytes data)??? = 30h, 30h, 30h - 39h, 39h, 39h (3 bytes data)?? = 30h, 30h – 39h, 39h (2 bytes data)#### = 30h, 30h, 30h, 30h – 3Fh, 3Fh, 3Fh, 3Fh (4 bytes data)### = 30h, 30h, 30h – 3Fh, 3Fh, 3Fh (3 bytes data)## = 30h, 30h – 3Fh, 3Fh (2 bytes data)# = 30h –3Fh (1 byte data) 30h, 30h - 3fh, 3fh (2 bytes data)