RENAULT SCENIC 3 (2009 - 2011) MKi + CK (EN_US).pdf
Transcript of RENAULT SCENIC 3 (2009 - 2011) MKi + CK (EN_US).pdf
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
Installation manual: Parrot MKi + Parrot CK3100 range
SCENIC 3
The brand name RENAULT SCENIC 3 and the RENAULT logo are the property of RENAULT. This document is only valid for the vehicle model SCENIC 3® year 2009 to 2011, excluding all other models in the same range and excluding later modifications made to the vehicle by the manufacturer. The Parrot brand name and logos are the exclusive property of Parrot SA.
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
Disassembly 45min
Kit installation 45min
Refitting 45min
Testing 15min
Total 2h30min
NO ACC wire
NO ISO
N/A UNIKA
FRONT SPEAKER TEL mode
ALL MUSIC mode
Fitting time (estimated) / Main features
Tools
Plastic trim removal tools FACOM / BERNER
FACOM DX-25 kit (n°4 tools)
Accessories required
"Please contact your Wholesalers to purchase accessories."
Kram ref. Dealer ref.
CK range 86795 77 11 428 303
MKi range 84795X795 77 11 428 303
Photos not contractually binding
Updating
- TORX screwdriver
- Cutting pliers
- Crimping pliers
- Multimeter or pilot lamp
- Hose clamp
- Electrical tape
- Round male terminals
CK range MKi range
To get the most out of your hands-free kit we recommend that you update your software regularly. The update procedure can be found at
www.parrot.com/usa/support/downloads
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
Disassembly
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
Disassembly 1 / 4
Using the plastic trim tools, unclip the car stereo surround.
Insert the removal tools into the slots on each side of the radio.
Unclip the radio, pull it up carefully, then remove the trim
tools.
Pull and lift the radio, disconnecting the connector and
the antenna.
1
3
2
4
5 6
Using the plastic trim tools, unclip the cover above the glove
box.
Using the plastic trim tools, unclip the cover located on the
right side of the dashboard.
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
Disassembly 2 / 4
Disconnect the connector for the passenger airbag trigger.
Unscrew screw 1 from the glove box.
Unscrew screw 2 from the glove box.
Unscrew screws 3, 4, 5 and 6 located above the glove box.
7
9
8
10
11 12
Pull the glove box firmly to unclip it and remove it, unplugging the
light connector.
Using the plastic trim tools, unclip the central screen
surround.
1
2
3
4
5 6
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
Disassembly 3 / 4
Disconnect and release the cover. Remove the fuse box cover.
Using the plastic trim tools, unclip the headlight adjuster and
disconnect it.
Using the plastic trim tools, unclip the cover on the left side of the
dashboard underneath the air vent and the side.
13
15
14
16
17 18
Unscrew screw 7. Unscrew screw 8.
7 8
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
Disassembly 4 / 4
Pull firmly to unclip the cover under the steering wheel and
put it on the floor. Do not remove the bottom.
Remove the door seal on the driver’s side.
19 20
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
On this same black connector, remove the small YELLOW wire on
the bottom row.
Finding an ACC wire
Under the steering wheel, just under the fuse box, remove the
large black connector.
Using a jumper or splice, connect a wire.
Pass the wire under the steering wheel towards the radio
housing.
1
3
2
4
5 6
Cut the red wire between the fuse holder and the ISO connector
provided. (Disconnect the blue wire in front of the fuse on connector
84795X795.)
Swap the fuse holders (i.e. the red and orange wires) and connect the
ACC wire. (Connect the wire directly to connector 84795X795.)
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
Pass the cable inside the rain sensor cover towards the cabin light.
Microphone feeding 1 / 2
Using the plastic trim tools, unclip the rain sensor cover.
Glue the support provided onto the cover after cleaning it, connecting the rain sensor.
Using the plastic trim tools, run the cable through the headliner towards the windscreen post on the driver’s
side.
1
3
2
4
5 6
Run the cable replacing the seal on the driver's door.
Pass the cable into the dashboard on the left side.
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
Microphone feeding 2 / 2
Run the cable under the dashboard towards the glove box
housing, attaching it with wire ties.
7
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
Feeding the accessory cable
On the bottom of the glove box, attach the cable to the bar
located above the light hole.
1
Bring it out leaving sufficient length.
2
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
Fitting the hands-free system 1 / 3
Connect the adaptor to the original connector, then pass the connector towards the glove box,
attaching it using wire ties in the glove box housing under the dashboard. Then connect all
of the cables to the blue box as shown in the diagram below. Test everything before
reassembly then slide all the cables behind the glove box and attach them with wire ties .
1
ISO adapter
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
Fitting the hands-free system 2 / 3
Remove the rubber covers. On the central screen surround.
Feed the cable from the screen through the central hole.
Stick the support (supplied) after cleaning, on the left side near to the
central screen hole and reposition the rubber cover.
1
3
2
4
5 6
Position the kit screen. Feed the cable from the top of the dashboard towards the glove box.
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
Fitting the hands-free system 2 / 3
Clip the central screen surround back on, reconnecting the screen.
7
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
Testing
Before refitting the system, switch the kit on using the ignition (or by starting the car). By pushing the central knob
of the remote control, check:
1 - That the menu is displayed on the screen. (Language or iPod.) 2 - That the system can be muted. (Click in the blue box.) 3 - That there is no sound coming from the speakers. 4 - That the sound from the voice menu is coming out of the front speakers. 5 - Then turn off the ignition, check that the kit switches off and that the "goodbye" message appears on the screen. (If this fails, reverse the fuses on the kit's wiring harness.) 6 - Pair a telephone with the kit to make a call. (Check that both the microphone and the kit are working.)
SCENIC 3
This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.
Reassembly
Refit the system using the following procedure: 1 – Re-install the radio reconnecting the adapter and antenna. 2 - Replace the car stereo surround. 3 - Clip the glove box back in place by pushing hard. (BE CAREFUL with the accessory cable.) 4 - Replace screws 1, 2, 3, 4, 5 and 6 in the glove box. 5 – Re-connect the passenger airbag selector. 6 – Re-fit the right dashboard panel. 7 - Replace the cover above the glove box. 8 – Re-fit the panel under the steering wheel by pushing hard. 9 - Replace screws 7 and 8. 10 – Re-connect and replace the headlight adjuster. 11 – Re-fit the panels on the left side of the dashboard.