Regupol Vibration 1000 · Width: 48" (1,219 mm) Max. static load 218.0 psi Peak loads (rare,...

REGUPOL AMERICA LLC | 11 RITTER WAY LEBANON, PA 17042

REGUPOL-ACOUSTICS.COM | 1.717.675.2190

Technology on Your Wavelength

Regupol® Vibration 1000

Regupol® Vibration 1000Standard forms of delivery, ex Lebanon, PA

Rolls Thickness: 10 mm Length: 30' (9,144 mm) Width: 48" (1,219 mm)

Max. static load 218.0 psi

Peak loads (rare, short-term loads) 254.0 psi

Static modulus of elasticity Based on EN 826 580 - 1,5954.0 - 11.0

psiN/mm2

Tangential modulus, see figure “Modulus of elasticity”

Dynamic modulus of elasticity Based on DIN 53513 2,176 - 6,52715.0 - 45.0

psiN/mm2

Depending on frequency, load and thickness, see figure “dynamic stiffness”

Mechanical loss factor DIN 53513 0.16 [-] Load-, amplitude- and frequency-dependent

Compression set Based on DIN EN ISO 1856

4.9 % Measured 30 minutes after decompression with 50% deformation / 23 °C after 72 hrs

Tensile strength Based on DIN EN ISO 1798

336.62.3

psiN/mm2

Elongation at break Based on DIN EN ISO 1798

110 %

Tear resistance Based on DIN ISO 34-1 85.7 lbs/in

Sliding friction in-house laboratoryin-house laboratory

0.60.7

[-][-]

Steel (dry)Concrete (dry)

Compression hardness Based onDIN EN ISO 3386-2

1,650 kPa Compressive stress at 25 % deformationTest specimen h = 60 mm

Rebound elasticity Based on DIN EN ISO 8307

37 % Depending on thickness, Test specimen h = 60 mm

Force reduction DIN EN 14904 45 % Depending on thickness, Test specimen h = 60 mm

Ozone resistance DIN EN ISO 17025 Cracking stage 0

[-]




Load Ranges

Load Deflection

Regupol® type

2.97.3

14.5

17.421.8

43.5

116.0

218.0

200 300 400 450 480 550 800 1000

Regupol® vibration M

ax.

sta

tic lo

ad

psi

0.020.05

0.10

0.120.15

0.30

0.80

1.50

N/mm2





Vibration Isolation

Natural Frequency


Illustration of the isolation efficiency of a single-degree-of-freedom system (SDOF system) on a rigid base with

Regupol® vibration 1000. Parameter: power transmission (insertion loss) in dB, isolation factor in %.

200

180

160

140

120

100

80

60

40

20

4 8 12 16 20 24

natural frequency [Hz]

dis

turb

ing

freq

uen

cy [

Hz]

28 32 36 40

-40 dB / 99 %

-35 dB / 98 %

-30 dB / 97 %

-25 dB / 94 %

-20 dB / 90 %

-10 dB / 69 %

0 dB / 0 %




Modulus of Elasticity

Dynamic Stiffness





Influence of Amplitude





Long-Term Creep Test

Regupol America, LLC is a product manufacturer and does not represent itself as a consultant, engineer, or advisor in construction methods, standards, and compliance. Therefore, Regupol America only warrants its products under its standard limited warranty (available by request), and does not represent or warrant any advice, suggestions, instructions, whether formal or informal, oral or written, in conjunction with any sales of its products. Any such advice is not intended for a particular purpose and should not be acted or relied upon as such. Any such advice is not represented as being all-inclusive, correct, complete or up-to-date.

The information and data contained herein are based on industry accepted testing, manufacturing tolerances and prior product usage as set forth. It is intended as descriptive of the performance characteristics and capabilities of Regupol/Regufoam and does not certify applicability for any particular or specific project. Technical assistance, calculations and design recommendations are available from Regupol America, and are subject to terms and conditions provided upon request.

Regupol 1000, Version 1, Release 10/2015

Regupol Vibration 1000 · Width: 48" (1,219 mm) Max. static load 218.0 psi Peak loads (rare,...

Documents

Transcript of Regupol Vibration 1000 · Width: 48" (1,219 mm) Max. static load 218.0 psi Peak loads (rare,...