Rectangular Tank Sizing
description
Transcript of Rectangular Tank Sizing
Page 1 of 13
Rectangular tank sizing Calculation
Objectives
- To calculate the thickness of tank plates- To determine the size of stiffening frame for tank- To determine dry and test weights
Assumptions
- Specific gravity of liquid is 1
-
- - Minimum Distance between stiffeners = 1.05m
References
1. UL-142, Steel Aboveground Tanks for flammable and combustible liquids, Underwriters Laboratories Inc.
2Publishing Inc.
3 Corus Construction and IndustrialStructural Sections to BS 4: Part 1:1993 & BS EN 10056:1999
4 ASME Boiler and Pressure Vessel Code Section II subpart D5 Trauvay and Cauvin (2001), Piping Equipment6
7th ed., McGraw-Hill. 20027 ASME B31.10M - 2000: Welded and Seamless Wrought Steel Pipe8 ASME B.16.5 - 2009: Pipe Flanges and Flanged Fittings
Notes
1 A total of 10 Stiffeners were used based on a spacing of 1.05 m on the long sides (3 stiffeners on each longer side; and 2 stiffeners on each shorter side)
2 Sump Pump weight was not included in calculations3 Weights are calculated weights. Final weights to be advised by vendor
Weight calulation does not include weir.
Acceleration due to gravity is 9.81 m/s2
Density of steel is 7850 kg/m3
Eugene F. Megyesy, Pressure Vessels Handbook, Pressure Vessels
Young, W. C. & Budynas, R. G. (2002) Roark's Formulas for Stress and Strain
Page 2 of 13
Page 3 of 13
Definition of Terms
- a Length of top plate
- b Width of top plate
- CA Corossion Allowance
- E Modulus of Elasticity
- g Gravitational acceleration
- H Height of tank
- Minimum Moment of inertia of top edge stiffening
- L Length of tank
- l Spacing between vertical stiffeners
- Spacing of bottom plate support
- R Reaction at top edge
- r Radius of contact of heaviest dead weight on top tank
- S Allowable stress of tank material
- t Required thickness
- Selected thickness
- w Load
- W Heaviest Dead weight on top plate
- Minimum Section Modulus of vertical stiffener
- α Factor Depending on ratio of Length to Width of top plate a/b
- β Factor Depending on ratio of Height to Length H/L
Density of tank material
ρ Density of liquid in tank
ν Poisson ratio of tank material
CSA Cross-Sectional Area
Imin
lb
ta
Zmin
ρp
Page 4 of 13
Page 5 of 13
Equipment Tag No. ABH 8000 Project No. 1216 No. of equipments 1
1 DESIGN DATA
Tank Material SA-516 Gr. 60
Modulus of Elasticity E = 203.4E+09
Allowable Stress S = 117.9E+06
Density of tank material = 7850Tank Dimensions:Length L = 4.2 mWidth W = 3 mHeight H = 2.4 mType of Liquid WaterSpecific Gravity = 1
Density of liquid ρ = 1000
Acceleration due to gravity g 9.81No. of vertical stiffeners one side = 3Maximum Distance between Stiffners l = 1.05 mCorrosion Allowance CA = 3 mmHeight/length ratio (H/L) = 0.5714Factor for H/L β = 0.095 (See Appendix)
2 SIDE PLATE THICKNESS
Required Plate Thickness = 0.00457334 m
= 4.57 mm
Thickness + Corossion Allowance = 7.57 mm
Selected Plate thickness = 8 mm
3 LOAD= 28252.8 N/m
= 28.25 N/mm
4 VERTICAL STIFFENINGMinimum Section Modulus
= 77.538
An equal angle L-section of dimensions
150 x 150 x 15 (section modulus = 83.5frame is satisfactory for vertical stiffening
Total no. of vertical stiffeners = 10 (Note 1)
N/m2
N/m2
ρp kg/m3
kg/m3
m/s2
ts
cm3
cm3)
S
gHlt
2
2gHw
S
HlwZ
1284.0min
Page 6 of 13
5 TOP EDGE STIFFENING
Reaction at top edge = 8.48 N/mm
Minimum required moment of inertia for top edge stiffening:
= 22512126
= 2251.2
200 x 200 x 16 (moment of inertia = 2342frame is satisfactory for vertical stiffening
BOTTOM PLATE SUPPORT SPACING
using a minimum plate thickness of 4.57 mm calculated for side plates above,the maximum spacing of bottom plate supports:
= 0.406 m
6 TOP PLATE THICKNESS
Dimensions of top plate
Length a = 4.4 m
Width b = 3.2 m
Constant based on length to width ratio a/b
a/b = 1.375
α = -0.000125 (See Appendix)
Poisson's ration 0.3
Total dead weight on tank top plate = 325.69 kg (Note 2)= 3195.0 N
Sum of Radii of load contacts with top plater = 1475 mm
Total Stress due to dead load on 4.57mm required plate thickness
= 30608563 N/m2
This Stress value is < S ( 117.9E+06therefore required thickness for side plates is adequate
Selected thickness = 8 mm
mm4
cm4
cm3)
N/m2)
gH
Stlb
254.1
r
b
t
W 2ln1
2
32
wR 3.0
aEt
RLI
192
4
min
Page 7 of 13
7 WEIGHT CALCULATIONS
a Weight of Tank Plates (Surface area of tank * tank thickness * Density of tank material)
i- Side plates= 2170.368
ii- Bottom Plate kg= 791.28
iii- Top Plate= 884.224
Total weight of tank plates = 3845.872
b Weight of StiffenersWeight of one vertical stiffener(CSA*Length*density of stiffener) = 84.78 kgTotal Weight of vertical Stiffeners = 847.8 kg
Weight of top edge stiffening(CSA*Length*density of stiffener) = 723.456 kg
Total weight of stiffeners = 1571.256 kg
c Weights of nozzles7 Nos. 2" nozzles @ 3.63 kg/Nozzle = 25.41 kg2 Nos. 4" nozzles @ 9.53 kg/Nozzle = 19.06 kg2 Nos. 24" Manways @ 140.61 kg/MW = 281.22 kg
Total weight of nozzles = 325.69 kg
d Total Empty weight of tank(Weights of tank plates+Stiffners+nozzles) = 5742.818 kg
Weight of water to fill tank(Volume of tank * density of water) = 30240 kg
e. Operating Weight(Empty weight of tank + Weight of water at NLL)
NLL = 1.06 m
Weight of water at NLL = 13356Total Operating Weight = 19098.818
f. Weight of tank filled with water(Empty weight of tank + Weight of water) = 35982.818 kg
kg/m3
)(2 WHLHt p
psLWt
psabt
Page 8 of 13
TANK SKETCH
Vertical Stiffener Cross-Section
150mm
150mm
15mm
200mm
200mm
16mm
1.05m
2.4m
1m
4.2m
3m
Top Plate4.4m x 3.2m
Page 9 of 13
Top-Edge stiffening Cross-Section
200mm
Page 10 of 13
Summary of Results
-- Tank material SA-516 Gr. 60
-- Thickness of platesSides = 8 mmBottom = 8 mm
Top = 8 mm
-- Number of vertical stiffeners = 10
-- Stiffener configuration Equal leg (L section)
Stiffener Cross-section Dimensions
Vertical = 150mm x 150mm x 15mm
Top edge = 200mm x 200mm x 16mm
-- Dry weight of tank = 5742.818 kg
-- Operating weight of tank = 19098.818 kg
-- Weight of tank filled with water = 35982.818 kg
Page 11 of 13
Page 12 of 13
APPENDIX
Values for factors used
1 2 3 4 5 6 7 8 9 10 11 12 13
Ratio 0.25 0.286 0.333 0.4 0.5 0.667 1 1.5 2 2.5 3 3.5 4
Constant β 0.024 0.031 0.041 0.056 0.08 0.116 0.16 0.26 0.34 0.38 0.43 0.47 0.49
Table 1: Values of βTable from Ref. 3
1 2 3 4 5 6
Ratio a/b 1 1.2 1.4 1.6 1.8 2 ∞
Constant α -0.238 -0.078 0.011 0.053 0.068 0.067 0.067
Table 2: Values of βTable from Ref. 8
Interpolation for β Interpolation for α
Col. No. β Col. No. β5 0.5 0.08 2 1.2 -0.0786 0.667 0.116 3 1.4 0.011
0.5714 0.095 1.375 -0.000125
H/L or H/l
H/L or H/l H/L or H/l
Page 13 of 13