RF-HI M HZ RF-HI M HZRF-HI M HZ RF-HI M HZ

b - 10 1 19 b - 10 1 19

7 65 .250 7 6 5 .250MHZ MHZ

DB DB

group channel rf audio gain group channel rf audio gain

pilot frequency pilot frequency

SCAN SCAN

IR

POWER

minmin

ma xma x

E AR P HO NE

W3

1

RECEIVER

RECEIVER INSTALL NOTICE :

Keep the receiver more than 1 meters from the ground and the wall ;remove the antenna and keep it perpendicular to get the prefectperformance .

2

1-power switch :turn on the switch,the lamp is on.2/3-

4-IR sending windon5/6-CHA/CHB volume control7/8-CHA/CHB LCD display9-earphone /audio input10-earphone volume control11-DC IN:DC12V,1200mA12-6.3mm mixed unbalanced output13/14-XLR unbalanced independent output15-antenna

setting key:SCAN/UP,IR/SET,LOCK/DOWNshort press SCAN/UP key,it is for scan function operation

scan out the free frequencyIR/SET,short press this key,it is for IR switch,put the mic IR window close tothe receiver IR window and press IR/SET key,if the transmitter frequency issame as receiver ,that means IR finished .Long press IR/SET key,it is for frequency setting ,long press to the frequencyflashing,then press UP or DOWN key to choose frequency.

2-back panel

1-front panel

IR

min max

9 10 812 3

4

5 67

b - 1 0 1 19 b - 1 0 1 19

765 . 250 765 . 2 50M HZ MHZ

DB DB

group channel rf audio gain group channel rf audio gain

pilot frequency pilot frequency

SCAN SCAN

POWER

min max

E A R P H O N E

W3

15 15 14 1512 13 1115

TRANSMITTER

4

Use left hand to Press batter open key and right hand to pull the battery case

1

2 3 6

4

5

M

HZ

-

-

6

7

8

5

1423

AF INANT

IRON/VOLOFF MAX

1-mic head2-LCD display3-power switch4-batter case:2*AA1.5V5-IR receiving window6-RF power:H -high power,L-low power

1-3.5mm audio input(mono)2-volume and power switch3-antenna4-IR receiving window5-metal pin cover6-LCD display7-RF power:H -high power,L-low power8-battery case:2*AA1.5V

Handheld

Bodypack

RECEIVER LCD DISPLAY :

3

1

2

4

9 3

A - 01 1 19

738 . 250 MHZ

DB

g rou p ch anne l r f aud io g a in

pilot frequency

75

611

8

1013

12

A - 0 1 1 19

73 8 .2 50 MHZ

DB

g rou p cha nne l r f aud io g a in

pilot frequency

1-IR sen ding window2-SE T:press SET /U P/DOW N ke y to ad ju st the menu for IR/fr eque ncy function3-DOW N: press SET /UP/D OW N k ey to ad just the menu for IR/frequency fu nc tion4-UP:p ress SE T/UP/D OW N key to adjust the menu for IR/freq uency function5-RF:RF sing al leve l,when the transmitt er is on6-AF:the AF singa l lev el,when the transmitte r is on and you talk to transmitt er7-frequen cy(6 40-680M Hz/740-790M Hz)8-chan ne l(CH01-10 0)9-volume con trol10-vo lume gain level11-true diversity an tanna A/B12-tr ansmitter ba tte ry life13-loc k function

1-IR freque ncy au tomatic func tion:press UP key (pu t the transmitt er IR receiv ing w indow to the receiver send in g window.)2-Lock func tionpress SE T key to YES LOC K/NO LOC K shining,i f sho w fo r NO LOCK ,i t means un lock,you can press U P k ey to Y ES LOCK ,it means for lock the m enu ,can not a djust any changefor func tion.

t ntion :Turn on the power switch on conference,if microphone lampis flashing ,it mean it is no battery ,you should change new battery.

6

TRANSMITTER

5

Turn the bottom batter cover to the left side,and press the batter plasticcover ,then open the battery cover.

1-power switch:ON/OFF2-power light3-LCD display:frequency,battery life4-RF power switch:upper is for low power,under is for high power5-4 pins XLR audio input for microphone6-IR receiving window:put <2 meters to the receiver IR sending

window when IR automatic frequency7-battery cover:alkaline AA1.5V battery*2pcs,please take the

batteries out if nouse for long time8-microphone pole

RF-H I M HZ RF-H I MHZ

+

+-

-

2

3

47

6

5

1-power switch2-IR receiving window3-LCD display4-setting key:long press SET to

choose frequency and RFpower5-battery locking key4-batter case:2*AA1.5V5-IR receiving window6-RF power:H -high power,L-low power

Handheld

Conference

A te

3.*Mixed output: plug the 6.3mm audio cable to MIXED-UNBAL on the receiver back side and connect mixer or amplifier MIX IN or AUX IN* Balance output: plug the XLR audio cable(provided by yourself) in BALA/B/C/D, and connect the mixer or amplifier MIC IN or AUX IN4. Press receiver switch,the LCD display is on,it means the machine is on . Open the transmitter and the RF is full level ,and now the MUTE is disappear on LCD of receiver. Speak to the microphone, AF level is rising up. Press switch for transmitter, microphone lamp is off but LCD is still without lamp, it means on MUTE position. Press on again to turn on the transmitter, the microphone is on. If the microphone lamp is flashing, it means low battery.5.SET setting: there are A/B/C/D channels, press SET2 times to be SEND and then ------, it means IR searching, when the IR setting is OK, the transmitter LCD background lamp is on. Now the transmitter and receiver

frequency is same .6.User can adjust for a better location, follow each person's sound, avoiding over-strong vol

OPERATING OFTRANSMITTER1.Open the battery cover and install 2AAbatteries. Make sure that the batteries are installed with the right polarity .2.Press power switch ,power lamp lighting express transmitter normal work3.Press the switch for 2 second to press power on for conference microphone4.Channel setting :can not use the same frequency at the same time and same place. Channel frequency set follow below: put the IR window for conference direct to IRA/B on receiver position, press SET key on CHA for 2 times, then to be SEND position,and then to be ------position, it means on IR searching ,then the LCD lamp is on,it means IR setting is OK, now the conference frequency and receiver frequency is same .

12V,800-1200mA5W

87

9