Rate-Based MEOH Model

22
Aspen Plus Rate-Based Model of the CO 2 Capture Process by Methanol using Aspen Plus

Transcript of Rate-Based MEOH Model

Page 1: Rate-Based MEOH Model

Aspen Plus

Rate-Based Model of the CO2 Capture Process by Methanol using Aspen Plus

Page 2: Rate-Based MEOH Model

Copyright (c) 2008 by Aspen Technology, Inc. All rights reserved.

Aspen Plus, the aspen leaf logo and Plantelligence and Enterprise Optimization are trademarks or registered trademarks of Aspen Technology, Inc., Cambridge, MA.

All other brand and product names are trademarks or registered trademarks of their respective companies.

This document is intended as a guide to using AspenTech's software. This documentation contains AspenTech proprietary and confidential information and may not be disclosed, used, or copied without the prior consent of AspenTech or as set forth in the applicable license agreement. Users are solely responsible for the proper use of the software and the application of the results obtained.

Although AspenTech has tested the software and reviewed the documentation, the sole warranty for the software may be found in the applicable license agreement between AspenTech and the user. ASPENTECH MAKES NO WARRANTY OR REPRESENTATION, EITHER EXPRESSED OR IMPLIED, WITH RESPECT TO THIS DOCUMENTATION, ITS QUALITY, PERFORMANCE, MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE.

Aspen Technology, Inc. 200 Wheeler Road Burlington, MA 01803-5501 USA Phone: (1) (781) 221-4300 Toll Free: (1) (888) 996-7100 URL: http://www.aspentech.com

Page 3: Rate-Based MEOH Model

Contents 1

Contents

Introduction............................................................................................................2

1 Components .........................................................................................................3

2 Process Description..............................................................................................4

3 Physical Properties...............................................................................................6

4 Simulation Approaches.......................................................................................15

5 Simulation Results .............................................................................................17

6 Conclusions ........................................................................................................18

References ............................................................................................................19

Page 4: Rate-Based MEOH Model

2 Introduction

Introduction

This document describes an Aspen Plus rate-based model of the CO2 capture process by methanol (MEOH) from a gas mixture of H2, CO2, CO, N2, CH4, H2S and COS from gasification of Western Kentucky coal char[1]. The operation data from a pilot scale absorber[1] are used to specify the feed conditions and unit operation block specifications in the model. Thermophysical property models have been validated against DIPPR correlations[2] for component vapor pressure and liquid density, and literature data for vapor-liquid equilibrium from Semenova (1979)[3] and Leo(1992)[4]. Transport property models have been validated against literature data for viscosity[5-9], thermal conductivity[10-13] , surface tension[7, 14-18], and diffusivity[19].

The model includes the following key features:

• PC-SAFT equation of state model for vapor pressure, liquid density and phase equilibrium

• Transport property models

• Rate-based model for absorber with ceramic Intalox saddles packing

Page 5: Rate-Based MEOH Model

1 Components 3

1 Components

The following components represent the chemical species present in the process:

Table 1. Components Used in the Model

ID Type Name Formula

MEOH CONV METHANOL CH4O

CO2 CONV CARBON-DIOXIDE CO2

H2S CONV HYDROGEN-SULFIDE H2S

CO CONV CARBON-MONOXIDE CO

N2 CONV NITROGEN N2

COS CONV CARBONYL-SULFIDE COS

H2 CONV HYDROGEN H2

CH4 CONV METHANE CH4

Page 6: Rate-Based MEOH Model

4 2 Process Description

2 Process Description

The flowsheet for the pilot plant[1] for CO2 capture by MEOH includes an absorber, a flash tank, a stripper and so on. However, only the absorber data are reported.

The sour gas enters the bottom of the absorber, contacts with lean MEOH solvent from the top counter-currently and leaves at the top as sweet gas, while the solvent flows out of the absorber at the bottom as the rich solvent with absorbed CO2 and some other gas components.

Table 2 presents the absorber’s typical operation data.

Page 7: Rate-Based MEOH Model

2 Process Description 5

Table 2. Data of the Absorber from the Pilot Plant [1]

Absorber

Diameter 0.127 m

Nominal Packing Height* 2.2 m

Packing Type ceramic Intalox saddles

Packing Size 6.25 mm(0.25 in)

Sour Gas

Flow rate 2.17 lbmol/hr

CO2 in Sour Gas 0.2801(mole fraction)

H2S in Sour Gas 0.00807(mole fraction)

Sweet Gas

CO2 in Sweet Gas 0.0095 (mole fraction)

H2S in Sweet Gas 0.00037 (mole fraction)

Lean MEOH

Flow rate 8.29lbmol/hr

Temperature -34.7F

Pressure 400psia**

* The column was found to be too high for the experiments and no absorption was detected above certain height of the packing [1]. Liquid and gas samples were taken at the height of 1.5m from the bottom as liquid feed and gas product. Therefore, effective packing height (1.5m), is used instead of the real height (2.2m) in this simulation model. This effective height was also used in the literature model [1].

** Because pressure unit is not reported explicitly [1], it is assumed to be psia based on the pressure data in Table II and Figure 12 of [1]

Page 8: Rate-Based MEOH Model

6 3 Physical Properties

3 Physical Properties

The PC-SAFT equation of state model is used to calculate vapor pressure, liquid density and phase equilibrium. The PC-SAFT pure component parameters for CO2, H2S, CO and COS have been regressed against vapor pressure and liquid density data generated from DIPPR correlations[2] for each component. For all other components, the PC-SAFT pure component parameters are taken from the work by Gross and Sadowski (2001, 2002)[20,21]. The binary parameters between CO2 and MEOH and H2S and MEOH have been regressed against vapor-liquid equilibrium data from Semenova (1979)[3] and Leu (1992)[4].

DIPPR correlation models[2] are used to calculate MEOH viscosity, thermal conductivity and surface tension, respectively; the predictions are in excellent agreement with literature data[5-18] as showed in Figures 13-15.

Wilke-Chang model[22] is used for calculating the gas diffusivity in MEOH. The model quality has been justified by CO2 diffusivity data from Littel (1991)[19] as showed in Figure 16.

Figures 1-16 show property predictions together with literature data.

Page 9: Rate-Based MEOH Model

3 Physical Properties 7

MEOH vapor pressure

0.00001

0.0001

0.001

0.01

0.1

1

10

100

150 250 350 450 550

Temperature, K

Vapo

r pre

ssur

e, b

ar

DataPC-SAFT

Figure 1. MEOH vapor pressure. PC-SAFT is used to fit data generated from DIPPR correlation[2] for methanol.

MEOH liquid density

300

400

500

600

700

800

900

1000

150 250 350 450 550

Temperature, K

Liqu

id d

ensi

ty, k

g/m

3

Data

PC-SAFT

Figure 2. MEOH liquid density. PC-SAFT is used to fit data generated from DIPPR correlation[2] for methanol.

Page 10: Rate-Based MEOH Model

8 3 Physical Properties

CO2 vapor pressure

0

10

20

30

40

50

60

70

200 220 240 260 280 300 320

Temperature, K

Vapo

r pre

ssur

e, b

ar Data

PC-SAFT

Figure 3. CO2 vapor pressure. PC-SAFT is used to fit data generated from DIPPR correlation[2] for CO2.

CO2 liquid density

500

600

700

800

900

1000

1100

1200

1300

200 220 240 260 280 300 320

Temperature, K

Liqu

id d

ensi

ty, k

g/m

3

Data

PC-SAFT

Figure 4. CO2 liquid density. PC-SAFT is used to fit data generated from DIPPR correlation[2] for CO2

Page 11: Rate-Based MEOH Model

3 Physical Properties 9

H2S vapor pressure

01020304050607080

180 230 280 330 380

Temperature, K

Vapo

r pre

ssur

e, b

ar Data

PC-SAFT

Figure 5. H2S vapor pressure. PC-SAFT is used to fit data generated from DIPPR correlation[2] for H2S.

H2S liquid density

300

400

500

600

700

800

900

1000

1100

180 230 280 330 380

Temperature, K

Liqu

id d

ensi

ty, k

g/m

3

Data

PC-SAFT

Figure 6. H2S liquid density. PC-SAFT is used to fit data generated from DIPPR correlation[2] for H2S.

Page 12: Rate-Based MEOH Model

10 3 Physical Properties

CO vapor pressure

05

10152025303540

70 90 110 130

Temperature, K

Vapo

r pre

ssur

e, b

arData

PC-SAFT

Figure 7. CO vapor pressure. PC-SAFT is used to fit data generated from DIPPR correlation[2] for CO

CO liquid density

400450500550600650700750800850

70 90 110 130

Temperature, K

Liqu

id d

ensi

ty, k

g/m

3

Data

PC-SAFT

Figure 8. CO liquid density. PC-SAFT is used to fit data generated from DIPPR correlation[2] for CO.

Page 13: Rate-Based MEOH Model

3 Physical Properties 11

COS vapor pressure

0

10

20

30

40

50

60

130 180 230 280 330 380

Temperature, K

Vapo

r pre

ssur

e, b

arData

PC-SAFT

Figure 9. COS vapor pressure. PC-SAFT is used to fit data generated from DIPPR correlation[2] for COS.

COS liquid density

600

700

800

900

1000

1100

1200

1300

1400

130 180 230 280 330 380

Temperature, K

Liqu

id d

ensi

ty, k

g/m

3

Data

PC-SAFT

Figure 10. COS liquid density. PC-SAFT is used to fit data generated from DIPPR correlation[2] for COS.

Page 14: Rate-Based MEOH Model

12 3 Physical Properties

Figure 11. Vapor-liquid equilibria of CO2-MEOH at three temperatures. Comparison of experimental data[3] to calculation results of PC-SAFT with adjustable binary parameter.

Figure 12. Vapor-liquid equilibria of H2S-MEOH at three temperatures. Comparison of experimental data[4] to calculation results of PC-SAFT with adjustable binary parameter.

Page 15: Rate-Based MEOH Model

3 Physical Properties 13

MEOH liquid viscosity

0.0001

0.001

0.01

0.1

150 200 250 300 350

Temperature, K

Visc

osity

, Pa.

s

Data

DIPPR

Figure 13. MEOH liquid viscosity. Comparison of literature data[5-9] to calculation results of DIPPR correlation model[2].

MEOH liquid thermal conductivity

0.15

0.2

0.25

200 250 300 350 400

Temperature, K

Ther

mal

con

duct

ivity

, W/m

-K

Data

DIPPR

Figure 14. MEOH liquid thermal conductivity. Comparison of literature data[10-13] to calculation results of DIPPR correlation model[2].

Page 16: Rate-Based MEOH Model

14 3 Physical Properties

MEOH surface tension

0.0001

0.001

0.01

0.1

250 300 350 400 450 500 550

Temperature, K

Surf

ace

tens

ion,

N/M

Data

DIPPR

Figure 15. MEOH liquid surface tension. Comparison of literature data[7,14-18] to calculation results of DIPPR correlation model[2].

Diffusivity of CO2 in MEOH

0

2

4

6

8

250 275 300 325 350

Temperature, K

Diff

usiv

ity (m

2/s)

*E9

Data

Wilke-Chang

Figure 16. CO2 diffusivity in MEOH. Comparison of experimental data[19] to calculation results of Wilke-Chang model[22].

Page 17: Rate-Based MEOH Model

4 Simulation Approaches 15

4 Simulation Approaches

Run 35I of the pilot absorber [1] is used in this work.

Simulation Flowsheet – The pilot absorber has been modeled with the following simulation flowsheet in Aspen Plus as shown in Figure 17.

LEANIN

GASIN

GASOUT

RICHOUT

ABSORBER

Figure 17. Rate-Based MEOH Flowsheet in Aspen Plus

Page 18: Rate-Based MEOH Model

16 4 Simulation Approaches

Unit Operations - The unit operation in this model has been represented by an Aspen Plus Block as outlined in Table 3.

Table 3. Aspen Plus Unit Operation Blocks Used in the Rate-Based MEOH Model

Unit Operation Aspen Plus Block Comments / Specifications

Absorber RadFrac 1. Calculation type: Rate-Based

2. Number of Stages: 10

3. Top Pressure: 400psia

4. Packing: 6.25mm(0.25in) ceramic Intalox saddles

5. Packing Height: 1.5m*

6. Mass transfer coefficient method: Onda (1968)

7. Interfacial area method: Onda (1968)

8. Interfacial area factor: 1

9. Film resistance option: Film for liquid and vapor

10. Flow model: Mixed

* The column was found to be too high for the experiments and no absorption was detected above certain height of the packing[1]. Liquid and gas samples were taken at the height of 1.5m from the bottom as liquid feed and gas product. Therefore, effective packing height(1.5m), is used instead of the real height(2.2m) in this simulation model. This effective height was also used in the literature model [1].

Streams - Feeds to the Rate-Based MEOH model are gas stream GASIN containing H2, CO2, CO, N2, CH4, H2S and COS and liquid solvent stream LEANIN containing pure MEOH solvent. Feed conditions are summarized in Table 4.

Table 4. Feed specification

Stream ID GASIN LEANIN

Substream: MIXED

Temperature: F 53.9 -34.7

Pressure:psia 400 400

Mole-flow: lbmol/hr

MEOH 0 8.29

CO2 0.608109 0.0

H2S 0.01752 0.0

CO 0.438551 0.0

N2 0.340854 0.0

COS 0.000977 0.0

H2 0.720569 0.0

CH4 0.043421 0.0

Page 19: Rate-Based MEOH Model

5 Simulation Results 17

5 Simulation Results

The simulation was performed using Aspen Plus version 2006.5. Key simulation results are presented in Table 5 and Figure 18. To illustrate the effectiveness of the rate-based approach, simulation results for the absorber using the equilibrium stage calculation type are also shown in Figure 18.

Table 5. Key Simulation Results

Measurement Rate-Based MEOH model

CO2 mole fraction in GASOUT 0.95% 1.235%

H2S mole fraction in GASOUT 0.037% 0.0008%

Temperature of RICHOUT, F 0.7 2.65

0

0.15

0.30.45

0.6

0.75

0.9

1.051.2

1.35

1.5

-45 -40 -35 -30 -25 -20 -15 -10 -5 0 5 10 15

Temperature, F

Pack

ing

Hei

ght,

m

Literature DataASPEN RateSepASPEN Equilibrium Stages

Figure 18. Absorber Liquid Temperature Profile

Page 20: Rate-Based MEOH Model

18 6 Conclusions

6 Conclusions

The Rate-Based MEOH model provides a rate-based rigorous simulation of the process. Key features of this rigorous simulation include the PC-SAFT equation of state model for vapor pressure, liquid density and phase equilibrium, rigorous transport property modeling, rate-based multi-stage simulation with Aspen Rate-Based Distillation which incorporates heat and mass transfer correlations accounting for columns specifics and hydraulics.

The model is meant to be used as a guide for modeling the CO2 capture process with MEOH. Users may use it as a starting point for more sophisticated models for process development, debottlenecking, plant and equipment design, among others.

Page 21: Rate-Based MEOH Model

References 19

References

[1] Kelly, R.M.; Rousseau, R.W.; Ferrell, K.F., “Design of Packed, Adiabatic Absorber: Physical Absorption of Acid Gases in Methanol,” Ind. Eng. Chem. Process. Des. Dev., 23, 102-109 (1984).

[2] DIPPR® 801 database, BYU-Thermophysical Properties Laboratory (2007).

[3] Semenova, A.I.; Emelyanova, E.A.; Tsimmerman, S.S.; Tsiklis, D.S., “The Phase Equilibrium in the System Methanol - Carbon Dioxide,” Zh. Fiz. Khim., 53, 2502-2505 (1979).

[4] Leu, A.D.; Carroll, J.J.; Robinson, D.B., “The Equilibrium Phase Properties of the Methanol – Hydrogen Sulfide Binary System,” Fluid Phase Equilib., 72, 163-172 (1992).

[5] Komarenko, V.G.; Manzhelii, V.G.; Radtsig, A.V., "Viscosity and Density of Normal Monobasic Alcohols at Low Temperatures, " Ukr. Fiz. Zh., 12, 4, 681 (1967).

[6] Bretsznajder, S., "Prediction of Transport and Other Physical Properties of Fluids, " International Series of Monographs in Chemical Engineering, Pergamon Press, Oxford, 2 (1971).

[7] Selected Values of Properties of Chemical Compounds, Data Project, Thermodynamics Research Center, Texas A&M University, College Station, Texas (1980-extant); loose-leaf data sheets.

[8] Rauf, M.A.; Stewart, G.H.; Farhataziz, "Viscosities and Densities of Binary Mixtures of 1-Alkanols from 15 to 55 C, " J. Chem. Eng. Data, 28, 324 (1983).

[9] Stephan, K.; Lucas, K., "Viscosity of Dense Fluids, " New York: Plenum Press (1979).

[10] Raal, J.D., Rijsdijk, R.L., "Measurement of Alcohol Thermal Conductivities Using a Relative Strain-Compensated Hot-Wire Method, " J. Chem. Eng. Data, 26, 351 (1981).

[11] Takizawa, S.; Murata, H.; Nagashima, A., "Measurement of the Thermal Conductivity of Liquids by Transient Hot-Wire Method, " Bull. Jsme., 21, 152, 273 (1978).

[12] Rastorguev, Yu. L.; Ganiev, Yu. A., "Thermal Conductivity of Aqueous Solutions of Organic Liquids, " Russ. J. Phys. Chem., 40, 7, 869 (1966).

Page 22: Rate-Based MEOH Model

20 References

[13] Mukhamedzyanov, I.Kh.; Mukhamedzyanov, G.Kh.; Usmanov, A.G., "Thermal Conductivity of Liquid Saturated Monobasic Alcohols at Pressures Below 2500 Bars, " Proc. of Kazan Chem. Tech. Inst. of S.W. Kirov, 44, 57 (1971).

[14] Kaye, G.W.C.; Laby, T.H., "Tables of Physical and Chemical Constants, 14th ed., " Longman Group, Limited, London (1973).

[15] Vargaftik, N.B., "Tables on the Thermophysical Properties of Liquids and Gases, 2nd ed., " Halsted Press, New York (1975).

[16] Jasper, J.J., "The Surface Tension of Pure Liquid Compounds, " J Phys Chem Ref Data, 1, 4, 841-1009 (1972).

[17] Riddick, J.A.; Bunger, W.B., "Organic Solvents: Physical Properties and Methods of Purification, 3rd ed., " Wiley Interscience, New York (1970).

[18] Won, Y.S.; Chung, D.K.; Mills, A.F., "Density, Viscosity, Surface Tension, and Carbon Dioxide Solubility and Diffusitivity of Methanol, Ethanol, Acqueous Propanol, and Acqueous Ethylene Glycol at 25 C, " J. Chem. Eng., 26, 2, 140 (1981).

[19] Littel, R.J.; Versteeg,G.F.; van Swaaij,W.P.M., “Physical absorption into nonaqueous solutions in a stirred cell reactor,” Chem. Eng. Sci., 46, 3308-3313 (1991).

[20] Gross, J.; Sadowski, G., “Perturbed-Chain SAFT: An Equation of State Based on a Perturbation Theory for Chain Molecules,” Ind. Eng. Chem. Res., 40, 1244-1260 (2001).

[21] Gross, J.; Sadowski, G., “Application of the Perturbed-Chain SAFT Equation of State to Associating Systems”, Ind. Eng. Chem. Res., 41, 5510-5515 (2002).

[22] Reid, R.C.; Prausnitz, J.M.; Poling, B.E., “The Properties of Gases and Liquids,” 4th ed.; McGraw-Hill: New York (1987).