RadianceRail Installation Guide€¦ · Test fit rails to check for accuracy. • Transfer...
Transcript of RadianceRail Installation Guide€¦ · Test fit rails to check for accuracy. • Transfer...
RadianceRail®
Installation Guide
decking | railing | lighting | fastening timbertech.com
Installing RadianceRail® with Balusters ............................................................................................................ 2
Installing RadianceRail® Stairs with Balusters ................................................................................................... 7
Notes ........................................................................................................................................................ 11
ATI Architectural Testing, Inc.CCRR-0114 • RadianceRail & RadianceRail Express
TimberTech Code ListingsOnce a product is tested by an independent lab, an application and report is submitted to one of several agencies that provide listings for building products that meet the requirements of Acceptance Criteria 174 (AC 174) as set forth by the International Code Council Evaluation Service (ICC-ES). TimberTech currently has listings from the ICC-ES and Architectural Testing Inc. The following TimberTech reports on code compliance are available to download on www.timbertech.com.
For the most up-to-date code listings visit
www.timbertech.com/installation.
• Please read all instructions completely before starting any part of the installation. • TimberTech Rail should be installed using the same good building principles used to install wood or composite railing and in accordance with the local building
codes and the installation guidelines included below. TimberTech accepts no liability or responsibility for the improper installation of this product. • TimberTech Rail may not be suitable for every application and it is the sole responsibility of the installer to be sure that TimberTech Rail is fit for the intended use.
Since all installations are unique, it is also the installer’s responsibility to determine specific requirements in regards to each Rail application. • TimberTech recommends that all applications be reviewed by a licensed architect, engineer or local building official before installation. If you have any questions
or need further assistance, please call TimberTech Customer Service at 1.800.307.7780 or visit our website at www.timbertech.com. • TimberTech Railing is tested as a whole system and should be used that way. It is not intended to be used in conjunction with other railing systems or fasteners. • The following Installation Guidelines are applicable for installation of TimberTech RadianceRail railing.• IMPORTANT: Make sure the DRIVE TOOL/DRILL is configured or set to use the SCREW setting when driving and/or tightening all FASTENERS.• SAFETY: Always wear goggles when handling, cutting, drilling and fastening materials. • Failure to install this product in accordance with applicable building codes and TimberTech’s written Rail Install Guide may lead to personal injury, affect rail system
performance and void the product warranty.
Page 2
Installing RadianceRail® with Balusters
Measuring Your Railing Area
Important Information
Component Dimensions
Tools Required
Components Needed For Installing One RadianceRail® SectionRadianceRail® is available in 10’, 8’, and 6’ lengths.
• Measurements are from center to center of the posts. Rails are produced in 10’, 8’, and 6’ lengths to allow for finished end cuts and angles.
• Determine how many 10’, 8’, and 6’ RadianceRail sections you need and check to be sure you have all the components (and quantities) listed in the chart shown to the right.
• RadianceRail 10’, 8’, and 6’ Rails are designed not to exceed
10’, 8’, and 6’’ center of post to center of post, respectively.
• For stair applications maximum rail length must not exceed 91”
• Cut slowly, using a fine tooth saw blade to avoid chipping.
• For 42” railing use 12’ Post Sleeves.
• Custom Rail Packs should be used when installing Aluminum
Balusters.
• Miter Saw• Drill• Measuring Tape
• 7/64” Drill Bit• 3/16” Drill Bit
Components Included
in Complete 6’ and 8’
Kits (white only).
Visit www.timbertech.com/installation to view TimberTech installation videos.
Consult your local building codes for guard and handrail requirements.
Components available
separately for
mix-and-match rail
systems
Additional Components
Needed for Each
System
1 - Top Rail1 - Bottom Rail2 - Support RailsFoot Blocks - 1 in 6’ kits - 2 in 8’ KitsSquare Balusters -13 in 6’ Kits -18 in 8’ KitsHardware Mounting KitSupport Block Mounting TemplatesBaluster Screw Kit
1 - Top Rail1 - Bottom Rail2 - Support Rails (1 - Aluminum Top Support Rail for 10')Hardware Mounting KitSupport Block Mounting TemplatesFoot Blocks - 1 in 6’ Packs, - 2 in 8’ Packs, - 3 in 10’ PacksR
adia
nceR
ail
Pack
Balu
ster
Pack
Hardware Mounting Kit4 - Mounting Brackets2 - Support Blocks16 - #8 x 3/4” Screws 6 - #8 x 1 3/4” Screws 6 - #8 x 2 5/8” Screws (Stairs Only) 3 - #8 x 3” Screws 12 - #8 x 3” Green Screws T20 Driver Bit
2 - Post Caps2 - Post Sleeve2 - Post Skirts
5”
5”
2.9”
3”2.25”
2.5”
1.8”
1.8”
1.25”
1.25”
.75”
Top Rail
Post Sleeve
Bottom Rail
Support RailSquare
Composite Baluster
Round Aluminum Baluster
Square Aluminum Baluster
Post Cap (2)
Top Rail (1)Mounting Bracket (4)
Support Rail (2)
Support Block (2)
Bottom Rail
Post Sleeve (2)
Composite Baluster(23 in 10’ Section)(18 in 8’ Section)(13 in 6’ Section)
Aluminum Baluster(25 in 10’ Section)(20 in 8’ Section)(15 in 6’ Section)
Post Skirt (2)
Foot Block(3 in 10’ Section)(2 in 8’ Section)(1 in 6’ Section)
.75”
.75”
.75”
Baluster Screw Kit18 - #8x2” Screws18 - #8x3” Screws
Baluster Screw Kit20 - #8x2” Screws20 - #8x3” Screws
Composite Balusters - 18 Balusters per Pack (23 required per 10’ section) (18 required per 8’ section) (13 required per 6’ section)
- 29” for 36” Railing - 31” for 36” Railing (with less than 2” gap between deck & Bottom Rail)
- 35” for 42” Railing - 37” for 42” Railing (with less than 2” gap between deck & Bottom Rail)
Aluminum Balusters - 20 Balusters per Pack (25 required per 10’ section) (20 required per 8’ section) (15 required per 6’ section)
- 29” for 36” Railing - 31” for 36” Railing (with less than 2” gap between deck & Bottom Rail)
- 35” for 42” Railing - 37” for 42” Railing (with less than 2” gap between deck & Bottom Rail)
Hardware included in
Hardware Mounting
Kits:
Page 3
Installing RadianceRail® with Balusters
1/3
1/3
1/31/2
1/2
1 2
3
• Trim Post Sleeves to desired length.
39” above deck surface is optimal for 36” railing heights.
• Slide Post Sleeve and Post Skirt over post (do not force).
• Ensure post are square and plumb.
INSTALL POSTSLEEVES
INSTALL LOWERSUPPORT BLOCK
• Position template at bottom of Post Sleeve above Post Skirt.
If you do not have a the template, positionthe top of the Support Block 4” above thedeck and 2-1/2” above the post skirt.
CUT AND ASSEMBLEBOTTOM SUPPORT RAIL
• Cut the Bottom Support Rail to length.
For sections up to 6’: Place one Foot Block in the center of the railFor sections 6’ to 8’: Space two Foot Blocks approximately at 1/3 intervals on the railFor sections 8’ to 10’: Space three Foot Blocks approximately at 1/4 intervals on the rail
45°
Straight SectionAngled Section
Center screw aligned to rail centerline
Foot blocks
8’ Section
6’ Section
Center screw aligned to rail centerline
Bracket set flush to rail face
Bracket set flush to rail face
For angled rail installations, align angled face of Support Block parallel to rail section.
Optimal 39” 4”2.5”
Template
Support Block
Post Skirt
Pre-Drill 7/64”#8 x 3” Coated Screws
Pre-Drill 7/64” for Brackets#8 x 3/4” Coated Screws
Pre-Drill 7/64”#8 x 3” Coated Screws
Page 4
Installing RadianceRail® with Balusters
4
5
INSTALL BOTTOM SUPPORT RAIL
SPACE BALUSTER ANDTRIM RAILS
The space between the end baluster and post can not exceed 4”
• Position Bottom Support Rail assembly onto Support Blocks.
• Measure distance between the posts at the Bottom Support Rail.
• Transfer measurement to Bottom Rail and center either on a pre-drilled hole or between two pre-drilled holes.
• Cut Bottom Rail and Top Support Rail to length.
#8 x 3” Green Coated Screws
CenterlineOdd number of balusters
Even number of balusters
7/64” Pre-Drill
#8 x 3” Green Coated Screws
Bottom Rail
Top Support Rail
Page 5
Installing RadianceRail® with Balusters
6
7
ASSEMBLE BALUSTERSECTION
INSTALL RAILASSEMBLY
• Attach Mounting Brackets at each end of the Top Support Rail as outlined in Step 3.
Position rail assembly with lip of Bottom Rail toward outside of deck, over bottom Support Rail.
• Align top Support Rail to center of posts.
Top Support Rail
Bottom Rail
Lip (facing out)
See step 3 for bracket installation
#8 x 3” Coated Green Screws
Align to center of post
7/64” Pre-Drill
#8 x 3” Coated Screws
Pre-Drill 7/64”#8 x 3/4” Coated Screws
#8 x 2” Coated Screws
Page 6
8 INSTALL TOP RAIL AND POST CAPS
• Measure and cut Top Rail to length. Trim both ends for a clean cut. • Attach Post caps using exterior grade caulk applied to the underside of the cap.
Caution: Screws must be 1 3/4” so they won’t go through the Top Rail on straight rail sections.
Post Cap
Top Rail
Pre-Drill 3/16”#8 x 1 3/4” Coated Screws
Installing RadianceRail® with Balusters
Page 7
Installing RadianceRail® Stairs with Balusters
Top Rail Length
Bottom Rail Length
1 2
• Trim Post Covers to desired length.
• Slide Post Cover and Post Skirt over post. Do not force.
• Ensure post are square and plumb.
INSTALL POSTCOVERS
TRIM RAILS
TRIM RAILS
Support Rails are rotated 90° for stair rail applications.
• Trim both the Top Support Rail and the Bottom Support Rail to those dimensions. Test fit rails to check for accuracy.
• Transfer measurement from Bottom Support Rail to Bottom Rail.
• Determine measurements and angle as shown.
• Trim Top Rail to match Top Support Rail at appropriate angle.
Stair Angle
Right Wrong
3
Bottom Rail
Top Rail
Top Support Rail
Bottom Support Rail
Page 8
Installing RadianceRail® Stairs with Balusters
4 5Drill BalusterHoles
TRIM BALUSTERS
ASSEMBLE BALUSTER SECTION
6
• Place the Bottom Rail and the Top Support Rail together as shown to keep the holes aligned.
• Separate the two rails, once all holes are drilled.
Drill 3/16” hole through the top Support Rail using the Bottom Rail holes for alignment, drilling at the same angle used to cut rail ends.
Bottom Rail and Top Support rail
Pre-Drill 3/16”
Important: Start cut at top edge to maximize the length.Trim Baluster ends to required angle as shown.
Aluminum stair Balusters are pre-cut to a stair angle and are not to be cut on the job site.
Bottom Rail
Top Support Rail
Lip (facing out)
Tip for Bottom Rail: Partially drive screws into all Balusters before driving them in completely.
Brackets must be on the side of the rail facing the stairs.
• Attach Brackets to Top Support Rail.
Pre-Drill 7/64”#8 x 3/4” Coated Screws
Center screw aligned with rail centerline
Scrap Piece of Wood Cut to Stair Angle
#8 x 3” Coated Screws
#8 x 2” Coated Screws
Page 9
Installing RadianceRail® Stairs with Balusters
7
8
INSTALL BOTTOMSUPPORT RAIL
INSTALL RAILASSEMBLY
Pre-Drill through Bottom Support Rail ONLY with 3/16” bit
Bottom Support Rail
#8 x 3” Coated Screw
• Wedge Foot Block under Support Rail & attach.
#8 x 3” Green Coated Screws
• Secure Mounting Brackets to posts.
Pre-Drill 7/64”
• Attach Mounting Brackets to Bottom Support Rails.
Pre-Drill 7/64”#8 x 3/4” Coated Screws
Center screw aligned with rail centerline
Brackets must be on the side of the rail facing the stairs.
For sections up to 6’: Place one Foot Block in the center of the rail
For sections 6’ to 8’: Space two Foot Blocks approximately at 1/3 intervals on the rail
Position and center rail assembly over Bottom Support Rail.
• Mark Ends of Top Support Rail.
• Rotate Rail assembly out of way to fasten Support Block.
• Secure Mounting Brackets to Posts.
Pre-Drill 7/64”#8 x 3” Coated Screws
Pre-Drill 7/64”#8 x 3” Green Coated Screws
Page 10
Installing RadianceRail® Stairs with Balusters
9 INSTALL TOP RAILAND POST CAPS
• Position Top Rail over Support Rail and attach with screws.
• Secure Post Caps with exterior grade caulk.
Pre-Drill 3/16”#8 x 2 5/8” Coated Screws
For typical stair angles, use provided 2 5/8” screws to fasten the Top Rail.
Page 11
Notes
RadianceRail®
Installation Guide
© 2014 TimberTech RRKITINSTALL (Balusters) | 02/14
TimberTech
894 Prairie Avenue
Wilmington, OH 45177
timbertech.com
1.800.307.7780