RADAR Automated Test &Measurement System (ATS) · – Automated Test System (ATS), meeting the...
Transcript of RADAR Automated Test &Measurement System (ATS) · – Automated Test System (ATS), meeting the...
1
RADAR Automated Test &Measurement System (ATS)
1. Introduction ISTRAC is responsible for the Design, Development, Integration, Testing and
commissioning of Radars required to cater the needs of ISRO as well as other national
requirements at X,C and S frequency bands. Characterisation of different subsystems and
system is essential during the development, system integration and system maintenance.
Radar Automated Test and Measurement System (ATS) is proposed for elaborate, accurate
and fast evaluation & qualification of subsystems and system to cater overall performance
specification of different radars.
ISTRAC has been using multiple bench top equipment like Signal Generators, Signal
Analysers, Network Analysers, Oscilloscopes etc. for testing various subsystems and
systems. ATS design with different test instruments and related Hardware & Software is
proposed here. The ATS should include all required test instruments for the characterization
of the Radars. ATS should be scalable, upgradeable and flexible in nature. The ATS should
also be of open architecture from a software perspective so that it can be automated or
integrated in any heterogeneous instruments and programming environment for the ease of
work and to improve test efficiency and timings.
Radar Automated Tests and Measurement System shall carry out the accurate system level
performance tests, measurements & calibrations and subsystem level functional and
performance tests including Antenna, Servo, Transmitter, Waveform Generator, RF Front-
end, RF/IF Receiver, Clock Generator, Digital Receiver and Signal Processor, Display &
Archival subsystems.
2. Guideline to Vendors: 2.1.Automated test System requirements for S, C & X-Band Radar Systems may be
combined in a single system.
2.2.Vendor shall develop common ATS control software and hardware to cater the
requirement for S, C and X-Band Radar.
2.3.Vendor shall develop ATS to cater requirement of individual subsystems &integrated
system level testing for S, C & X-Band Radar systems.
2.4.Only OEMs and OEM certified Authorised Dealers are required to submit the quote.
Certificate issued by OEMs should be provided along with the quote.
2
2.5.Vendor is required to quote for 5 years warranty and application support.
2.6.All Software Source codes and installation kit containing actual deliverable software
shall be provided.
2.7.All the ATS modules shall be of 19” Rack mountable unit, with necessary power,
cabling and any other additional accessories.
2.8.The ATS shall be deployed at different places of Radar. ATS shall be designed with
easy dismantling features and also suitable packing shall be provided for the purpose
of transportation and quick installation and integration.
2.9.ISTRAC shall evaluate the price bids of technically qualified vendors for deciding
lowest bidder (L-1) on the basis of ultimate landing cost including all the deliverables,
calibrations, soft wares and warranty as per TENDER.
2.10. L1 will be computed based on the total landing cost with five years warranty.
Extended warranty will execute after the completion of 5 years warranty at the
discretion of ISTRAC.
3. Scope of Work
Building, integrating (both hardware and software segments) and supplying integrated Radar
– Automated Test System (ATS), meeting the following requirements:
3.1.Shall be able to Test all subsystems sequentially as per the specifications. It shall be
possible to test even single subsystem independently.
3.2.Shall provide all the external interfaces needed by all the DUTs and control the
DUTs. Shall be able to power all or any one of the DUTs selectively. However,
measurements can be sequential.
3.3.All the test instruments, switch matrix and RF cables need to be calibrated
automatically by ATS and to be used before any measurements.
3.4.Shall be able to run through the complete test plan without any further manual
intervention, once the setup is made and calibration is done.
3.5.A single GUI software package shall be provided to carry out all test and evaluation
and calibration as listed in the document.
3.6.The software package shall have all flexibilities to configure the instruments to its
maximum and minimum specifications, formulate test cases etc. GUI also supports
self-calibration of instruments and generates the report.
3
3.7.The ATS software shall be implemented such that it is modular, easily amenable to
modifications/expansions without major change in the "core" of the software.
3.8.ATS software shall be able to process the measured data and shall be able to generate
plots, export the data to Microsoft Excel spread sheets or any spread sheet software,
e.g. open-office & PDF format with all the necessary annotations.
3.9.Integrated Automatic report generation for all tests shall be a part of the software.
3.10. Vector Network Analyzer
will be supplied by ISTRAC. The vendor shall integrate the
VNA supplied by ISTRAC into the ATS. The ATS software shall be capable of handling
VNA also. The overall ATS block diagram with Radar DUT is shown in Figure. 1.
3.11. The vendor shall carry out on-
site calibration of the equipments of the ATS as listed
in Table.1. The periodicity of calibration shall be as follows:
a) Once every six months
b) Whenever any equipment is found to be out of calibration.
Automated warning message shall be generated to alert the initiation of the calibration
process.
3.12. Detailed calibration, test and evaluation requirement is listed in the document.
The test instruments required and configuration requirement also listed. However,
there may be requirement of additional instruments or configuration to complete all
the calibration and testing listed in the document. It is the responsibility of the vendor
to identify such instrument or adding additional configuration while quoting the
tender and explain in detail. If any part of the test is unable to complete with the setup
projected by ISTRAC or the vendor modified configuration will lead into non-
compliance of deliverables.
3.13. Proper naming convention shall be defined to identify different radar systems
and subsystems.
3.14. ATS supply voltage: 230V ac , single phase, 50 Hz (nominal)
3.15. Vendor has to work out data backup plan on separate machine (workstation as
listed in Table.1) Automatic data transfer after each test set is required. It should have
feature of viewing test report from backup machine.
3.16. Modifications in the specifications and test plan, if any, will be intimated at
the time of PDR.
4
Fig.1 ATS Block Diagram for Radar DUT
3.17. Tests and Calibrations to be performed by the software application
Following are the list of Tests and Calibrations to be performed by ATS:
3.17.1. SSPA/Klystron/Magnetron Transmitter tests
(i) Power Output for Long, Medium, Short Pulses over BW
(ii) Interlocks and Status
(iii)Triggers/Timings/Controls
(iv) VSWR
(v) Rise time, fall time, pulse droop, pulse distortion
3.17.2. RF Front-end tests
(i) Gain, P1dB
5
(ii) Dynamic Range/Linearity, Sensitivity
(iii)Noise Figure
(iv) Bandwidth, Harmonics & Spurious
(v) Intermodulation Distortion
(vi) LO Spectral Purity, Image Rejection
3.17.3. IF Receiver tests
(i) Gain, P1dB
(ii) Dynamic Range/Linearity
(iii)Noise Figure
(iv) Bandwidth
(v) Harmonics & Spurious
(vi) Intermodulation Distortion, Image rejection
3.17.4. Antenna System RF Testing
(i) Antenna Gain
(ii) Radiation Pattern
(iii) Co-pol
(iv) Cross-pol
(v) Sidelobes
(vi) Radome loss
(vii) Beamwidth & Pointing Accuracy
3.17.5. Radar Waveform Generator
(i) Pulse measurements – rise time, fall time,
(ii) Spectrum – Harmonics, spurious
(iii) Phase Noise
3.17.6. Digital Receiver, DSP, Data Processor & Displays tests
(i) Power Level Sweep, Frequency Level Sweep
(ii) Pulsed RF measurements
(iii) Real Signal-to-Noise Ratio (SNR in dB)
(iv) Phase Noise Performance
(v) Wideband Noise Performance
(vi) Jitter and SNR Performance of the Signal generator as a Clock Source
(vii) Jitter Bandwidth
(viii) Distortion and Spurious
(ix) Signal-to-noise and distortion (SINAD in dB)
(x) Total harmonic distortion (THD in dBc)
(xi) Spurious-free dynamic range (SFDR)
6
(xii) Third-order input intercept point (IIP3 in dBm)
(xiii) Harmonics
(xiv) Non-Harmonics
3.17.7. Integrated Radar Testing
(i) Dynamic Range
(ii) Doppler Sweep
(iii)Multi carrier Dynamic and Doppler Sweep Tests.
3.18. Deliverables:
3.18.1. Hardware Deliverables of ATS: The vendor shall deliver the
instruments and hardware as listed in Table.1 for the RADAR Automated
Tests and Measurement System for S, C & X Band along with all Manuals.
Refer Annexure-1 for the detailed specifications of the instruments and the
hardware listed in the Table.1.
Table1: RADAR Automated Tests and Measurement System
Module (Test Instruments and Hardware) Qty (Nos)
1) Real Time Spectrum Analyzer (Detailed Specifications in Table 3) 1
2) Arbitrary Waveform Generator (Detailed Specifications in Table 4) 1
3) RF Signal Generators (Detailed Specifications in Table 5) 3
4) RF & Clock Signal Generator (Detailed Specifications in Table 6) 1
5) Mixed Signal Oscilloscope (Detailed Specifications in Table 7) 2
6) Arbitrary Function Generator (Detailed Specifications in Table 8) 2
7) RF Switch Matrix(Detailed Specifications in Table 9) 1
8) Workstation (Detailed Specifications in Table 10) 2
9) Laptop (Detailed Specifications in Table 11) 2
10) 10G Rack mount Ethernet LAN Switch (Detailed Specifications in
Table 12)
3
11) 19” Instrumentation Rack with required accessories (Detailed
Specifications in Table 13)
1
12) ATS Software Application for all the test cases 1
3.18.2. 18.2 Software Deliverables of ATS:
ATS Software Application shall be developed to carry out all the test cases mentioned
in point 17 Tests and Calibrations and shall have following requirements:
7
3.18.2.1. Documents: Vendor should provide Software Requirement Specification
(SRS), Software Design Document (SDD), User manual for software and offer
them for review.
3.18.2.2. All Software Source Code and Installation Kit containing actual deliverable
software shall be provided.
3.18.2.3. Code walk-through is to be conducted by ISTRAC team along with vendor
at the time of ATP.
3.18.2.4. Software Audit to be conducted by ISTRAC team before final delivery.
3.18.2.5. The vendor shall ensure continued support for the supplied software
including the Operating system on which the application resides for a period
of at least five years from the date of acceptance.
3.18.2.6. ATS Software applications should have the following quality attributes:
a) Security: Login and password facility with user registration and password
recovery mechanism. All important configuration files and code files should
be protected with separate administrative password. Session time out facility.
b) Software should be maintainable which includes modification, corrections,
improvements or adaptation of the software to changes in environment. To
achieve this modularity of software is compulsory along with version control
feature.
c) GUI of ATS shall have following features: display- preferably: User id and
DUT, Instrument connectivity status, Input parameters entry, Test result and
test condition selection, Test result status, Test completion time and error
message display. GUI shall be elegant and user friendly with all settings
through user editable configuration files.
4. Requirement Specification Review & Preliminary Design Review
Vendor shall prepare system requirement document including Hardware and Software
requirements within 3 weeks after the confirmation of the order. This document shall we
reviewed and vetted by ISTRAC team before PDR.
Vendor shall conduct a Preliminary Design Review (PDR) approximately 6 weeks after
confirmation of order. PDR will consist of design/configuration (block diagram), Interface
details, Software Design etc., of ATS. Acceptance Test Plan (ATP) shall be prepared by
vendor in consultation with RDA, ISTRAC.
8
4.1.Factory Acceptance Testing (FAT)
Upon completion of the ATS development, vendor shall demonstrate the compliance of
functional requirements and measurement accuracy/ precision specifications as per mutually
agreed Acceptance Test Plan (ATP) including software. ISTRAC/ ISRO representative may
witness the Pre-shipment Clearance Testing at manufacturer’s premises. Shipment clearance
will be given after successful completion of FAT.
4.2.Site Acceptance Test (SAT)
Vendor is responsible for installation and commissioning of the Radar Automated Test
System (ATS) at ISTRAC, Bangalore or at a place in India, as suggested by ISTRAC. Upon
completion of the installation and commissioning of ATS at site, vendor shall demonstrate
the compliance of functional requirements and measurement accuracy/ precision
specifications as mentioned in ATP. ISTRAC Engineer(s) shall be witnessing the acceptance
testing at the time of ATP. The ATS will be accepted after the successful completion of the
ATP cleared by ISTRAC/ISRO Committee.
5. Training Once the system is installed and operational, training shall be held. System Engineer familiar
with the hardware, software and test methodologies shall conduct this training. The training
shall focus on familiarization with the instrumentation, test methodologies, programming and
operational usage of the ATS.
6. On Site Application Support Vendor shall provide application support for 5 years after acceptance of the system. System
Engineer familiar with the hardware, software and test methodologies used shall be available
to deliver this support. This support shall immediately follow the system installation and
training.
In case of any failure in ATS, vendor shall respond to ISTRAC within2 days (48 hrs.)with
respect to the request sent by ISTRAC. After that vendor has to correct the fault within 4
days (96 hours).
9
7. Warranty, Support and Calibration ATS shall have 5 years of warranty. If 5 years warranty is not available as standard, vendor
shall quote for standard warranty plus chargeable warranty for remaining term. If equipments
are to be sent for calibration/repair, pickup and delivery from site of installation shall be done
by vendor only at no additional costs.
8. Payment terms & conditions along with delivery schedule Payment terms: Vendor shall specify payment terms and conditions.
Delivery Schedule:
Table-2 Delivery Schedule
System Requirements Specification
(SRS) Review
3 Weeks after confirmation of order by vendor
Preliminary Design Review (PDR) 6 Weeks after confirmation of order by vendor
Factory Acceptance Testing (FAT) 20 weeks after confirmation of order by vendor
Site Acceptance Testing (SAT) 22 weeks after confirmation of order by vendor
Note: ISTRAC will provide DUTs for SAT.
9. Documentation For ATS, vendor shall produce custom system documentation and compile it into a System
Reference Manual. This shall include
Operating manual for the ATS.
Comprehensive Service manual for maintaining the complete system
ATS Calibration data and procedure.
Custom System Reference Documentation shall include rack layout, system interconnect
diagrams, serialized instrument/equipment and other hardware list, custom cable pin out
tables and certificates as applicable. The documents shall be supplied in electronic form.
10. Additional Guideline to vendors 10.1. The vendor shall examine the whole RFP thoroughly and offer point by point
compliance matrix indicating clearly the parameter/specification in tabular format for
their offer. In case of non-compliance, the deviation from the specified parameter
shall be furnished.
10.2. Vendor must quote for all the points mentioned in RPF. All the test cases (Section
3 Scope of Work, point 17) are necessary for offer consideration.
10.3. Vendor shall quote in two parts :
10
a. Part 1: Technical offer along with masked price-bid
b. Part 2: Commercial offer
10.4. Vendor can attach additional information if any, which may provide more
information on ATS.
10.5. The delivery schedule shall be presented in a bar chart form showing sequence and
time of all important activities e.g. ATS development, testing etc.( including design
reviews etc.)
11
Annexure-1
Detailed Specifications of ATS Items
11.Real Time Spectrum Analyzer
Table: 3 Technical Specifications for Real Time Spectrum Analyzer
S. No. Parameter Specifications
11.1. Architecture Real time Spectrum analyzer
11.2. Frequency Range 10 Hz to 12 GHz or better
11.3. Real-time acquisition bandwidth 150 MHzor better
11.4. Aging Rate Better than 1 x 10-7
/year
11.5.
Displayed Average Noise Level
(Without Preamp) Better than –140dBm/Hz at 12 GHz
11.6.
Displayed Average Noise Level
(With Preamp) Better than –150dBm/Hz at 12 GHz
11.7. Harmonic Distortion Better than –65dBc at 12 GHz
11.8. Spectrum Length Upto 32K points
11.9. Selectivity Better than 5:1
11.10. Spurious Free Dynamic Range Better than70dBc
11.11. Trigger Modes Free Run, Single Triggered
11.12. Trigger Types Power, Frequency, Time
11.13. Detectors ±Peak, Average (VRMS), Sample
11.14. Pulse Measurements Pulse Trace, Pulse Table
11.15.
Phase Noise & Jitter
Measurements
Should support Phase Noise as well as Jitter
Measurement
-130dBc @10KHz offset @1GHz
11.16.
Noise Figure and Gain
Should support Noise Figure and Gain
Measurement with following specification
or better
Gain Range: -10 to 30 dB
Noise figure Range: 0 to 30 dB
Resolution : 0.01dB
Noise figure measurement error : ±0.1dB
Gain measurement error : ±0.1dB
12
11.17. Display LCD/LED Display
11.18. Interfaces LAN, USB
11.19. Operating Temperature Range 0 °C to 55 °C
11.20. Power Requirement 230V ± 10%, Frequency: 50 Hz ± 3%
11.21. Rack Mountable accessories To be provided
11.22. Warranty
Quote for 5 Years of Warranty with periodic
calibration.
11.23. Operating and service Manual
Soft and Hard copy of manual needs to be
provided.
11.24.
All necessary connectors and
adapters are to be provided by
the vendor to carry out the
required test.
11.25.
Calibration Kit & Calibration
certificate to be provided.
12. Arbitrary Waveform Generator
Table:4 Technical Specifications for Arbitrary Waveform Generator
S.No. Parameter Specifications
12.1. Number of Channels 2 Analog Channels
12.2. Frequency Output 10 GHz or better
12.3. Analog Bandwidth 10 GHz or better
12.4. Rise Time 25ps or better
12.5. DAC Sampling rate 20 GS/s or better
12.6. Vertical Resolution 8 Bits or better
12.7. Waveform Memory 1 GSamples on both channels or better
12.8. Spurious Free Dynamic Range - 40 dBc or better
12.9. Flatness Parameter Better than ± 2 dB
12.10.
Triggering & Run Modes Continuous, Triggered and Triggered
Continuous & Individual sequences can
be run on each channel
12.11. Interface LAN, USB
13
12.12. Display Characteristics LCD/LED display
12.13.
Radar Generation Capabilities
(IQ, IF&RF Waveforms)
1) Modulation types, viz. FM Chirp,
NLFM, FM Step, User-defined Step FM
2) Define all Pulse Parameters including
Start Time, Rise Time, Off Time, Fall
Time, Pulse Width, and impairments like
Droop, Overshoot, and Ripple
3) Define a Staggered PRI with Ramp,
User-defined Profiles and Multipath
4) Ability to generate IQ impairments
like I/O imbalance, Quadrature error,
carrier Leakage
12.14. Operating Temp. Range 0 °C to 40 °C
12.15. Power Requirement 230V ± 10%, Frequency: 50 Hz ± 3%
12.16. Rack Mountable accessories To be provided
12.17.
Warranty Quote for 5 Years of Warranty with
periodic calibration.
12.18.
Operating and service Manual Soft and Hard copy of manual needs to
be provided.
12.19.
All necessary connectors and
adapters are to be provided by
the vendor to carry out the
required test.
12.20.
Calibration Kit & Calibration
certificate to be provided.
13. RF Signal Generator
Table:5 Technical Specifications for RF Signal Generator
S. No. Parameter Specifications
13.1. Frequency Range: 100 kHz to 12.75 GHz
13.2. Frequency Resolution 0.001 Hz
13.3. Frequency error < 1 × 10–7
13.4. Reference Frequency 10MHz (internal and external)
14
13.5. Reference oscillator OCXO
13.6.
Power Level range (above 1
MHz)
–140 dBm to +15 dBm or better
13.7. Power Level Resolution 0.01 dB
13.8.
Maximum permissible reverse
power
0.5W
13.9. Harmonics < –30 dBc
13.10.
SSB phase noise @ 10GHz
(1Hz bandwidth), carrier offset
20KHz
<-97dBc
13.11.
Frequency sweep Trigger mode
Digital mode with free run, full sweep,
execute one step, external trigger, internal
trigger
13.12. Trigger source
external trigger, remote control, internal
trigger
13.13. Sweep range full frequency range
13.14. Sweep shape triangle, sawtooth
13.15. Step spacing linear
13.16. Power level sweep
digital sweep in discrete steps with 0.01 dB
resolution
13.17. Trigger mode
free run, full sweep, execute one step,
external trigger, internal trigger
13.18.
Trigger source for power and
frequency sweep
external connector, remote control
13.19.
Trigger slope for power and
frequency sweep
(with external trigger) positive, negative
13.20. Power Sweep shape triangle, sawtooth
13.21. Step spacing logarithmic
13.22.
Dwell time setting range for
power and frequency sweep
10 ms to 10 s
13.23.
Modulation Type
Amplitude modulation, Frequency
modulation, Phase modulation, Pulse
modulation, Pulse generator, Pulse train with
internal and external modulation source.
13.24. Pulse modulation On/off ratio > 80 dB
15
13.25.
Minimum width for pulse
modulation
20 ns
13.26.
Repetition frequency for pulse
modulation
0 Hz to 10 MHz
13.27. Pulse generator mode single pulse, double pulse
13.28. Pulse generator Trigger modes
free run, internally triggered, externally
triggered, externally gated
13.29. Pulse period setting range 40ns to 40s
13.30.
Pulse period , pulse width
&Pulse delay setting resolution
10 ns
13.31. Pulse width setting range 20 ns to 1 s
13.32.
Pulse delay setting range (with
external trigger)
10 ns to 1 s
13.33.
Double-pulse spacing setting
range
20 ns to 1 s
13.34. Pulse Train : Trigger modes automatic (free run),externally triggered
13.35. Number of pulses in pulse train 1 to 2047
13.36.
Pulse width and pulse spacing
setting range in pulse train
20 ns to 5ms
13.37.
Pulse width and pulse spacing
setting resolution in pulse train
10 ns
13.38. Remote control Interface Ethernet/LAN (VISA interface), USB
13.39. Operating Temp. Range 0 °C to 55 °C
13.40. Power Requirement 230V ± 10%, Frequency: 50 Hz ± 3%
13.41. Rack Mountable accessories To be provided
13.42. Warranty
Quote for 5 Years of Warranty with periodic
calibration.
13.43.
Operating and service Manual Soft and Hard copy of manual needs to be
provided.
13.44.
All necessary connectors and
adapters are to be provided by
the vendor to carry out the
required test.
13.45.
Calibration Kit & Calibration
certificate to be provided..
16
14. RF &CLOCK Signal Generator
Table: 11. Technical Specifications for RF & CLOCK Signal Generator
S.No. Parameter Specifications
14.1.
ADC Characterization
Should support latest ADC, DACs like AD9208
Dual 3 Gsps 14b A/D converter, AD9172 Dual
12Gsps 16b D/A converter
14.2. Frequency Range Better than 12 GHz
14.3. Resolution of setting 0.001 Hz
14.4. Frequency error < 1 × 10–7
; Aging: ≤ 3 × 10–8
/year
14.5. Reference Frequency 10MHz (internal and external)
14.6. Power Level Setting range –120 dBm to +18 dBm
14.7. Maximum permissible reverse power 10W or higher with reverse power protection
14.8. Harmonics ( f = 12GHz) < -55 dBc @ 10dBm
14.9.
SSB phase noise CW, standard
performance, carrier offset 20kHz CW,
measurement bandwidth 1 Hz, level =
10 dBm
< -115dBc (1GHz to 10GHz carrier)
14.10.
Modulation Type
Amplitude modulation, Frequency modulation,
Phase modulation, Pulse modulation, Pulse
generator, Pulse train with internal and external
modulation source.
14.11. Pulse modulation On/off ratio > 80 dB
14.12. Minimum width for pulse modulation <20 ns
14.13. Pulse generator modes single pulse, double pulse
14.14. Pulse generator Trigger modes
free run, internally triggered, externally triggered,
externally gated
14.15.
Multifunction generator - Frequency
Range
Sine : 0.1 Hz to 10 MHz; pulse, triangle, trapezoid
: 0.01 Hz to 1 MHz
14.16.
Multifunction generator - noise
bandwidth
100 kHz to 10 MHz
14.17. Signal Types - LF Generator 1 sine, pulse, triangle, trapezoid
14.18. Signal Types - LF Generator 2 sine, pulse, triangle, trapezoid
17
14.19.
Noise generator (noise amplitude
distribution)
Gaussian, equal
14.20. Resolution Sine : 0.01Hz; pulse, triangle, trapezoid : 10 ns
14.21. noise bandwidth 100kHz
14.22.
Internal Differential Clock Synthesizer
up to 6GHz
14.23. Clock Signal Generation
differential square wave, differential sine wave,
single-ended sine wave, differential CMOS
14.24. Frequency range 10MHz to 6GHz
14.25. Resolution 0.001Hz
14.26. Level Setting Range
–24 dBm to 20dBm (sine wave, differential and
single-ended) 0.8 V to 2.7 V (differential CMOS)
14.27. Remote control Interface Ethernet/LAN (VISA interface), USB, serial
14.28. Operating Temp. Range 0 °C to 55 °C
14.29. Power Requirement
230V ± 10%, Freque
ncy: 50 Hz ± 3%
14.30. Rack Mountable accessories To be provided
14.31. Warranty
Quote for 5 Years of Warranty with periodic
calibration.
14.32.
Operating and service Manual Soft and Hard copy of manual needs to be
provided.
14.33.
All necessary connectors and adapters
are to be provided by the vendor to carry
out the required test.
14.34.
Calibration Kit & Calibration certificate
to be provided.
15. Mixed Signal Oscilloscope
Table: 6.Technical Specifications for Mixed Signal Oscilloscope
S.No. Parameter Specifications
15.1. No of Analog input channels 4
15.2. No of Digital input channels 16
15.3. Bandwidth 500 MHz
18
15.4. ADC Resolution 10 bits or better
15.5. Sample Rate
5 GS/s or better on all analog channels&
2 GS/s or better on all digital channels
15.6. Record Length
62.5 Mpoints or better on all analog &
digital channels
15.7. Acquisition Modes Sample, Peak detect
15.8. Analog input coupling Both DC and AC
15.9. Analog Input impedance 50 Ω and 1 MΩ
15.10.
Maximum input Analog
voltage
50 Ω: 5 VRMS, with peaks ≤ ±20 V
1 MΩ: 300 VRMS, CAT II
15.11.
Minimum detectable pulse
width
5 ns or better
15.12. Trigger modes Auto, Normal, and Single
15.13. Cursor types
Waveform, V Bars, H Bars, and V&H
Bars
15.14.
Amplitude measurements
Amplitude, Maximum, Minimum, Peak-
to-Peak, Positive Overshoot, Negative
Overshoot, Mean, RMS, AC RMS, Top,
Base, and Area
15.15.
Timing measurements
Period, Frequency, Unit Interval, Data
Rate, Positive Pulse Width, Negative
Pulse Width, Skew, Delay, Rise Time,
Fall Time, Phase, Rising Slew Rate,
Falling Slew Rate, Burst Width, Positive
Duty Cycle, Negative Duty Cycle
15.16. Display type 14 inch or better
15.17. External reference input external 10 MHz reference
15.18. Interfaces USB, Ethernet
15.19. Probes Analog and Digital Logic Probes
15.20. Operating Temp. Range 10 °C to 40 °C
15.21. Power Requirement 230V ± 10%, Frequency: 50 Hz ± 3%
15.22. Rack Mountable accessories To be provided
15.23. Warranty
Quote for 5 Years of Warranty with
periodic calibration.
15.24. Operating and service Soft and Hard copy of manual needs to
19
Manual be provided.
15.25.
All necessary connectors and
adapters are to be provided
by the vendor to carry out
the required test.
15.26.
Calibration Kit &
Calibration certificate to be
provided.
16. Arbitrary Function Generator
Table: 7. Technical Specifications for Arbitrary/Function Generator
S.No. Specifications
16.1. No. of channels : Two
16.2.
Waveforms : Sine, Square, Pulse, Ramp, Triangle, sinc, Gaussian, Noise,
arbitrary waveforms & more type of waveforms will be preferable
16.3.
(i) Sine Wave: 1 microHz to 240 MHz or better, Burst Mode :1 microHz
to120 MHz or better
(ii) Square Wave : 1 microHz to 120 MHz or better , Rise/Fall time< 3 ns
(iii) Pulse Wave : 1 mHz to 120 MHz or better ,pulse width 5.00 ns to
900 s or better, pulse duty 0.001% to 99%,Overshoot <5%
(iv) Arbitrary Waveforms : 1 mHz to 120 MHz or better, Vertical
resolution 14 bits, Rise/Fall time <= 3 ns ,Memory: 128 K
samples & Sample rate 250 MS/s or better
16.4. Modulation : AM, FM, PM, FSK, PWM
16.5. Phase noise at 20 MHz, 10 kHz offset : < -100 dBc/Hz or better
16.6. Harmonic Distortion : < -50 dBc or better
16.7. Amplitude, 50 ohm Load : 50 mVp-p to 4 Vp-p
16.8.
Auxiliary Inputs: 10 MHz Reference Input , Trigger input.
Auxiliary Outputs: Trigger Output,10 MHz Reference Out Remote
Programming interface :USB and LAN
Main Output impedance: 50 ohm , Connector: BNC(F)
16.9.
Power supply input:
230V ± 10%, Frequency: 50 Hz ± 3%(Indian power plug & power cord)
20
17. RF Switch Matrix
Table: 8. Technical Specifications for RF Switch Matrix
16.10. Operating Temperature Range: 0 °C to 55 °C
16.11. Rack Mountable accessories to be provided
16.12. Warranty : Quote for 5 Years of Warranty with periodic calibration.
16.13.
Operating and service Manual: Soft and Hard copy of manual needs to be
provided.
16.14.
All necessary connectors and adapters are to be provided by the vendor to
carry out the required test.
16.15. Calibration Kit & Calibration certificate to be provided.
Switch Matrix Specifications
17.1. Frequency 10 MHz to 15 GHz
17.2. Insertion Loss 1 dB or Better
17.3. Isolation 90 dB or Better
17.4. VSWR at input port 1.3:1
17.5. Switching speed ~15ms
17.6. Impedance 50 Ohm
17.7. Life cycle ~5million
17.8. Communication Controller with LAN interface
17.9. Driving Module
proper driving module Should be
provided
17.10. power handling 1W Avg & 50 W peak
17.11. power supply 220 to 240 V AC
17.12.
Switch matrix configuration
6x6 switch matrix -2 Nosto interface all
instruments and DUT
17.13. Attenuator(0-90 dB 10dB step) 4 Nos
17.14. Attenuator(0-70 dB 10dB step) 4Nos
17.15. Attenuator(0-10 dB 1dB step) 4Nos
17.16. Terminators 50 Ohm 20 Nos
17.17. PDC(1:4) 4 Nos
17.18. PDC(1:2) 4 Nos
21
18. Workstation
Table: 9. Technical Specifications for Workstation
S.No Features Specification
18.1 Make and Model Mandatory to Provide Make & Model
18.2 Details of Product
Specifications website
and URL (web
address) link
Mandatory to provide Product Specifications
website and its URL link
18.3 Processor
2 Nos. of Intel Xeon Silver 4116 Processor 2.1 GHz
or better
18.4 Chipset Intel C622
18.5 RAM 64 GB ECC, DDR4, 2400 MHz memory
18.6 Internal Storage 2 Nos of 1TB SSD Hard Disk
18.7 Optical Drive Internal DVD RW
18.8 Graphics Card
NVIDIA 8GB Graphics Card or better shall be
delivered.
18.9
Network
a) Integrated Dual Port one Gigabit Ethernet
b) Dual Port 10 GbE T- RJ 45 Port Card, down
gradable to 1G Support.
18.10
Key Board
Standard Wired USB Keyboard. The offered
workstation and Keyboard shall be from same
OEM. 18.11
Mouse
Standard Optical USB mouse with 3 button one
scroll wheel. The offered workstation and mouse
shall be from same OEM.
18.12
Power Supply
Power - Power supply with 80% or better efficiency,
Power Supply rating: 220 volt/50 Hz shall be
delivered 18.13
Ports Ports – Front :2 USB, Rear: 4 USB, Audio in, out
and Microphone shall be delivered
18.14
Chassis
Workstation tower model, Completely tool less
chassis with handles in front and rear side. Rack
mountable accessories to be provided
18.15 Certification RoHS, WEEE, EPEAT Gold – ENERGY STAR.
18.16 Operating System
Windows 10 Professional 64 bit with One Year
Standard support shall be delivered
18.17 Software
Microsoft Office Suite with service pack – Latest
version
18.18 Warranty 5 years Onsite Warranty
18.19
Monitor
The supplied workstation and monitor shall be from
same OEM.
Vendor shall deliver required video cables /
convertors along with the monitor. All cables and
convertors shall be OEM certified hardware
22
Supplied Monitors shall have following
specification or better
27-inch IPS LED Monitor or Better.
Panel Type/ Surface: LED backlight, antiglare,
Widescreen Flat Panel Display
Aspect Ratio: 16:9
Viewing angle: 178° horizontal; 178° vertical
Brightness: 300 cd/m2 or better
Contrast Ratio: 1000:1 static; 8000000:1 dynamic
Power Supply rating: 220 volt/50 Hz.
Interface: Compatible with the offered workstation
model suitable to drive dual display configuration.
18.20
Installation &
Commissioning
Vendor should install & commission the systems as
per the configuration at RDA, ISTRAC Bangalore.
System installation, commissioning is the sole
responsibility of the vendor. It includes the
installation of all hardware, operating system, all
necessary device drivers and system libraries.
At the time of installation and commissioning of the
configuration, if it is found that some additional
hardware accessories or software items with
licenses are required to complete the configuration
to meet the operational requirement of the
configuration which were not included in the
vendor's original list of deliverables, then vendor is
required to supply such items to ensure the
completeness of the configuration at no extra cost to
ISTRAC. Vendor should ensure completeness of the
list of deliverables in the offer to avoid such
discovery during installation.
Vendor should resolve all issues related to
compatibility of hardware, drivers, and other system
software with OS.
18.21
Notes to the Vendor
The offered product shall be from a reputed OEM
who owns such product line for at least for last five
years.
Vendor shall submit following certifications from
OEM on OEM’s letter head.
The vendor is authorized for participating in the bid.
The offered workstation hardware is not an obsolete
product.
The offered hardware / software component is back
to back supported by the OEM during the warranty
period.
For all items in the list of deliverables offered by the
vendor, the manufacturer's part number should be
clearly indicated. Offer of items without clear
specification of part number is not acceptable.
23
19. Laptop Table: 10. Technical Specifications for Laptop
Sl.
No Parameter specifications
19.1 Make and Model Mandatory to Provide Make & Model
19.2 Processor 8th Generation Intel® Core™ i7 processor, Quad
Core or better
19.3 Operating System Windows 10 Professional 64 bit OS
19.4 Memory 16GB DDR4 or Better
19.5 Hard Drive 1TB SSD Hard drive
19.6 Display 14 to 16 inch FHD or Better
19.7 Video NVIDIA 2GB DDR3 or Better
19.8 Ports 3 USB3.0 or Better
19.9 Network 10/100/1000 Ethernet
19.10 Battery 3 Cell 48 WHr battery or Better
19.11 Bluetooth& WLAN Should Support
19.12 Mouse Cordless mouse
19.13 DVD Writer External USB slim DVD +/- RW Optical Drive
19.14 Accessories 1TB USB based SSD
19.15 Accessories Laptop leather bag with cushioned compartment
with additional compartments for peripherals
19.16 Software Microsoft Office Suite with service pack – Latest
version
19.17 power pack External power pack
19.18 Adapter AC Adapter
19.19 Warranty 5 Years
19.20 Power Requirement 230V ± 10%, Frequency: 50 Hz ± 3%
19.21 Notes to the Vendor
The offered product shall be from a reputed OEM
who owns such product line for at least for last five
years.
Vendor shall submit following certifications from
OEM on OEM’s letter head.
The vendor is authorized for
participating in the bid.
The offered workstation hardware
is not an obsolete product.
The offered hardware / software
component is back to back supported by the OEM
during the warranty period.
24
20. 10G Rack mount Ethernet LAN switch
Table: 12. Technical Specifications for 10G Rack mount Ethernet LAN switch
Sl No: Parameter Specification
20.1. Item 10 G Ethernet Switch
20.2. I/O ports and slots 12 or more RJ45 1G/10GBASE–T ports
2 SFPs or more
20.3. SFP module Switch should be loaded with 2 Nos. of 10G SR
transceivers in multi-mode fiber.
20.4. Multi-mode fiber patch
cords
3 Nos. should be included
20.5. memory 512 MB RAM or better
256 MB FLASH or better
20.6. Packet buffer size 2 MB or better
20.7. processor Cortex-A9 @ 1.25MHz or better frequency
20.8. latency Less than 5uS
20.9. Throughput/packet
forwarding rate
238 Mpps or better for 64 byte packet size
20.10. Routing/Switching
capacity
320 Gbps
20.11. Routing table size 500 entries or better
20.12. MAC address table size 16000 entries or better
20.13. MTBF 30 years or better
20.14. Switching & routing Layer -2 switching & Layer -3 static routing
20.15. IPv4 static routing & IPv6
static routing
Support IPv4 & IPv6 static routing
20.16. Access Control Lists
(ACLs)
Layer –L2/Layer –L3
20.17. Mounting scheme Rack mounting
20.18. Warranty 5 Years
20.19. Cat 6 A Patch Cords 25mtr – 6Nos, 10mtr-5nos, 5 Mts-10Nos.
20.20. Management Should be Manageable
20.21. Operating Temperature
Range 0 °C to 55 °C
25
21. 19” Instrumentation Rack
Table: 13. Technical Specifications for 19” Instrumentation Rack
S.No. Specifications
21.1
Height 42U
Width 600 mm
Depth 800 mm
21.2 Static load-carrying capacity 400 kg
21.3 Type of protection IP 55
21.4 Shielding up to 50 dB at 1 GHz, 40 dB at 3 GHz (tested to IEC 61587-3)
21.5 Fan top cover cooling with minimum 4 fans
21.6 Perforated base plate with cable ducting
21.7
Welded basic frame with conductive seal all-around, Front door, rear door,
side panel
21.8 GND/earthing kit to be provided
21.9 Adjustable foot & Raised top cover
21.10 Power supply distribution
AC supply 230V ,50Hz (Indian power plug & power cord)
21.11 Any other additional accessories
21.12 Operating Temperature Range: 0 °C to 55 °C
21.13 Warranty: 5 Years
20.22. Power Requirement 230V ± 10%, Frequency: 50 Hz ± 3%
20.23. Rack Mountable
accessories To be provided
20.24. Operating and service
Manual Soft and Hard copy of manual needs to be provided.
20.25. Vendor should install & commission the systems as per the configuration at RDA,
ISTRAC Bangalore.
20.26. Vendor should provide technical brochure and Compliance statement for the given
Specifications
26
22. GENERAL REQUIREMENTS FOR INSTRUMENTS
(TECHNICAL LITERATURE SHALL BE SUPPLIED, WHEREVER APPLICABLE)
22.1. Vendor should quote for only new equipment (No quote will be accepted for refurbished or used
equipment)
22.2 Vendor should quote for all required hardware/software/calibration standards required to meet all
the above specifications.
a. All the specifications offered by vendor shall be guaranteed specifications referenced to
instrument’s published technical data sheet.
b. If any specification is specified as typical value only, in vendor data sheet then vendor must
certify separately that the delivered instrument will comply with the tender specification at the
time of installation/commissioning.
c. In case, both, guaranteed as well as typical specs are given in data sheet, then only guaranteed
specs will be considered. Typical specs will be ignored.
22.3 Vendor should indicate the quoted equipment model and accessories parts numbers in support for
each specification in tabular form
22.4 All parts/ accessories should have operating power: 220 to 240V AC, 50 Hz. All necessary power
cords with Indian (3-pin plug) type to be provided by vendor.
22.5 Only OEM or their authorized representative for India shall quote with authorization certificate.
22.6 Operational, programming and service manual (Electronic form) must be provided with the
instrument.
22.7
For technical evaluation of the bids, if required by ISTRAC, the vendor may be asked to give
demonstration of the instrument functionality at RDA/ISTRAC, Bangalore of the quoted model
with all the options and accessories required to meet the tender specifications.