Qvoice Companion Training
Transcript of Qvoice Companion Training
BY SONJOY KUMAR BASAK
Qvoice Companion Training
NEXT
1
QVoice System
What is Qvoice?System OverviewMeasurement PrincipleQvoice FeatureStarting Qvoice CompanionSequence of configuration stepsLogout Qvoice Companion
BACK NEXTHOME
2
What is Qvoice?
QVoice: Exceptionally efficient and versatile test system for analyzing the quality of speech and data in mobile networks.
Quality of service speech/video telephony/IP data transfer/MMS/SMS
Air interface dataFrequency spectrum /ChannelsLocation & Time by GPS
BACK NEXTHOME
3
System Overview
Qvoice SmartQvoice CompanionQvoice Symphony
BACK NEXTHOME
4
Qvoice Companion
Qvoice is used primarily for network optimization & benchmarking operations for which the resource of a notebook pc are sufficient up to 4 measurement Channel can be used.
Speech measurements with perceptual evaluation of speech quality(p.862 according to ITU) are also possible by using MIAs(Measurement Interface Adapters) for the measurement Channels.
BACK NEXTHOME
5
Measurement Principle
Speech between Qvoice mobile & QVS- Speech
Speech between Qvoice mobile & Answer station
IP data(HTTP, FTP, Video Streaming,…. ) between Qvoice mobile & public server
IP data (same as 3, Plus UDP) between Qvoice & QVS data
Video telephony, MMS, SMS,….between two Qvoice mobileBACK NEXTHOME
6
Measurement Principle
ChanelSpeech masterSpeech Slave
BACK NEXTHOME
7
Measurement Principle
Channel: A channel is used for measuring speech/data quality via one mobile phone(or one ISDN Channel/one PSTN line)
Master & Slave: The master always the first call & controls the measurement. With Qvoice each measurement Channel can be configured as a Master or as a Slave. Master & Slave must be equipped with a DSP
BACK NEXTHOME
8
Measurement Principle
The following terms refer to the Master: MOC: The master makes the call MTC: The master is called by the slave UPLINK: The master transmits speech
samples (measured at the slave) DOWNLINK: The master receives speech
samples The measurement procedure is always controlled by the master
BACK NEXTHOME
9
Measurement Principle
Maximum call duration: After 10 hours of measurement operation Qvoice stops all measurements & then starts up again using the same measurement parameters. The size of the measurement files will be limited & the time re-transmitted to the slaves.
BACK NEXTHOME
10
Qvoice Features
Clear parameter administrationServices & measured data
BACK NEXTHOME
11
Clear Parameter Administration
Subscriptions: summarise all the SIM dataDestinations: contain all the information on
the remote stations/serversMeasurement Programs: contain the
specific measurement instructionsMeasurement Configurations: summarise
all the measurement information for one Channel
BACK NEXTHOME
12
Services and measured data
SpeechVideo telephonyPingHTTPFTPUDPEmailWAPVideo streamingMMSSMS
BACK NEXTHOME
13
Starting Qvoice Companion
Start the PC/NotebookDouble Click the “Qvoice Companion” from Desktop shortcut. Then open <<Qvoice Companion MU Launcher>>
Start the PC/NotebookDouble Click the “Qvoice Companion” from Desktop shortcut. Then open <<Qvoice Companion MU Launcher>>
BACK NEXTHOME
14
MUA & MEA are ready then Click <<Start UI >> button
BACK NEXTHOME
15
Address: localhostUser name: administratorPassword: passwordThen Click Login button
BACK NEXT
HOME16
Starting progress
BACK NEXTHOME
17
Sequence of Configuration Steps
H/W ConfigurationSubscription EditorDestination EditorMeasurement Program EditorMeasurement Configuration Editor
BACK NEXTHOME
18
H/W Configuration
All port configure are enable then go to next step
BACK NEXTHOME
19
Subscription Editor
Click Subscription Editor
BACK NEXTHOME
20
Add New SIM Subscription
BACK NEXTHOME
21
Select SIM subscription
BACK NEXTHOME
22
Write the name ,Speech number, CS data number, MCC & MNC
BACK NEXTHOME
23
Save & Refresh subscription list (Important)
BACK NEXTHOME
24
Select destination editor
Destination Editor
BACK NEXTHOME
25
Add new destination
BACK NEXTHOME
26
Select CS destination
BACK NEXTHOME
27
Write the Name, Speech number & data number
BACK NEXTHOME
28
Always Save & Refresh After entering name & Cell number
BACK NEXTHOME
29
Measurement Program Editor
A measurement program contains: 1.Test Operations
2. Parameter for each Test Operation
BACK NEXTHOME
30
Select Measurement Program Editor
BACK NEXTHOME
31
BACK NEXTHOME
Add new Measurement Program
32
HOMEBACK NEXT
Add new Test Operation
33
Select Speech Master
HOMEBACK NEXT
34
Write Name & Test Operation setup
BACK NEXTHOME
35
Always Save & Refresh After entering name & All setup
BACK NEXTHOME
36
Measurement Configuration Editor
Measurement ChannelSubscription Used(=network provider, enabled
services, etc)Measurement program(=service to be measured,
parameters)Destination(remote station) for the test operationsChannel Capabilities(Example: <<Trace GSM>>)
BACK NEXTHOME
37
BACK NEXTHOME
Click Measurement Configuration Editor
38
Click Add new configuration
BACK NEXTHOME
39
Enter Name, Channel, Subscription name, Speech type(Master or slave), Destination & Channel Capabilities
BACK NEXTHOME
40
Channel Idle mode
BACK NEXTHOME
41
Start Selected Measurement Program
BACK NEXTHOME
42
Logout QVoice Companion
From the <<Control panel>> click the <<Stop all Channels button
Wait for all the measurement channels to stop
Exit Qvoice with <<Logout(+MU Shutdown)>>
NOTE: Always First Stop Master Channel then stop Slave
43
BACK NEXTHOME
Stop all channels & Wait for all measurement channels to stop
BACK NEXTHOME
44
Logout(+MU Shutdown)
BACK NEXTHOME
45
BACK NEXTHOME
Exit Login Box then Close MU Launcher
46
Double Click(Desktop shortcut) Qvoice Export
BACK NEXTHOME
47
First Click Check box, Secondly click right button then select copy
BACK NEXTHOME
48
For change directory browse the folder
BACK NEXTHOME
40
BACK NEXTHOME
Create new folder then ok
50
THANK YOU
51