QUIETFLOW SQS - Amazon S3...3.0 Start Up 3.1 Before power is supplied to the unit, check that the...

These instructions must be read fully before commencing installation.

QUIETFLOW SQS Installation & Maintenance

Tel 01384 275800 Fax 01384 275810 Email [email protected] Website eltafans.com2

Installation InstructionsQUIETFLOW SQS

1.0 General1.1 It is important these Installation and Maintenance Instructions are fully adhered to.1.2 Full details of the unit supplied are shown on the product nameplate. If in doubt about any detail contact Elta Fans Ltd or its agents for clarification.1.3 All electrical installation must be carried out by suitably qualified and competent personnel in accordance with all current statutory requirements.1.4 These instructions cover only the Elta Fans Ltd product and do not include the supply or installation of any safety equipment that may be required e.g. adequate guarding or protection from rotating parts and proper electrical isolation.1.5 Any declarations made by Elta Fans Ltd about product installation and safety, are dependant on the fan equipment being used within installations which themselves meet the requirements of the relevant Standards and Directives of your region.1.6 The fan is designed for use in an ambient temperature of -20°C up to a maximum of +60°C and up to 95% relative humidity. The fan is not suitable for corrosive or explosive atmospheres.1.7 The installer should provide easy access to the fan to facilitate future maintenance.1.8 The installer should ensure the fan is adequately supported.1.9 This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible for their safety. Children should be supervised to ensure that they do not play with the product.1.10 At end-of-life, the unit must be disposed of in an environmentally friendly manner by suitably qualified and competent personnel ina ccordance with the requirements of applicable Standards and Directives.

2.0 Installation

WARNING – The fan must be isolated from the power supply during installation and maintenance. The fan must be earthed in accordance with the local regulations.

2.1 Upon receipt, the fan equipment should be visually inspected to check for any damage. Ensure that the impeller is free to rotate.2.2 If there are any queries concerning the fan equipment, Elta Fans Ltd should be contacted prior to the installation.2.3 The fan must be securely mounted in the desired position to suit the application. The fan can be mounted at any angle.2.4 Check the details on the motor rating plate to ensure that the correct power supply (voltage, frequency and phase) is available. An incorrect power supply will lead to permanent damage to the fan motor.2.5 Refer to the appropriate wiring diagram. Ensure that all earth connections are made.2.6 Means for electrical disconnection must be incorporated in the wiring installation in accordance with the relevant wiring and electrical regulations.2.7 Precaution must be taken to locate the exhaust discharge terminal so as to avoid the backflow of gases into the room from the open flue of gas or other fuel burning appliances.

EC

Please note: This is an estimated adjustment guide

149-CD-POT

The 149-CD-POT is a commissiong device designed to be used with our EC range of fans.

This device will be as standard with our box fan range from May 2018.

The device will allow the for the installer to set the maximum operating speed of the fan that it isconnected to.

The installer or commissioning engineer can adjust the fan speed using the potentiometer built onto the149-CD-POT board. This potentionmeter can either be used for single speed adjustment or to set amaximum speed for the fan to operate at when an external control source is used.

If external speed control is required, the jumper connection next to the potentionmeter on the boardwould need to be removed, the installer can then connect to ST1 (using the diagram provided).

When an external speed control is �tted, the maximum speed setting available to the external control islimited by the potentiometer setting of the commissioning device.

10/07/2018MK-149-CD-POT Issue: Saved Date:A

Level / Speed OHMS (Ω)

10 10 (Ω)

9 9 (Ω)

8 8 (Ω)

7 7 (Ω)

6 6 (Ω)

5 5 (Ω)

4 4 (Ω)

3 3 (Ω)

2 1.5 (Ω)

1 500 (Ω)

0 1 (Ω)149-CD-POT

Elta Fans Limited has a policy of continuous product development and improvement and therefore reserves the right to supply products which may differ from those illustrated and described in this publication. Confirmation of dimensions and data will be supplied on request. 3

Installation InstructionsQUIETFLOW SQS EC

3.0 Start Up3.1 Before power is supplied to the unit, check that the wiring is correct as per the fan connection diagram.3.2 At initial start-up, check that impeller rotation and airflow direction is correct.3.3 Check that the motor amperage drawn does not exceed the nameplate rating.

4.0 Fan Maintenance4.1 Inspection of the fan at least once every 12 months is recommended to ensure that the motor, fan blades, and supporting guards, are clean. Any build up of dust and deposits on the blades or guards should be removed using a non-abrasive cleaner.4.2 All fastenings should be checked for tightness. In addition, all rotating items should be checked.4.3 Bearings are of the ‘sealed for life’ type and will not need a detailed inspection.

IMPORTANT - The EC fan has internal electronic overload protection and the AC fan is fitted with an auto-reset thermal cut-out which switches the fan off in the event of a fault condition. Once the motor cools down the fan may start unexpectedly. Only a suitably qualified and competent person may carry out maintenance after the electrical supply has been isolated.

GND 10V E1

MIN MAX

E1GND

ST1

ST2

ST2

E110VGND

MAXMIN

ST1

GND E1

THE ABOVE DIAGRAM SHOWS "ST2".

"ST2" CONNECTIONS ARE FACTORY FITTED.

GND = COMMON•10V = 10VDC INPUT•E1 = 0-10VDC OUTPUT•

YOU CAN DETERMINE THE CURRENT VDC OUTPUT BYDISCONNECTING POWER TO THE UNIT, SETTING AMULTIMETER TO OHMS (Ω) AND PLACING THE TEST PROBESBETWEEN GND AND E1

PLEASE USE THE ESTIMATED ADJUSTMENT GUIDE FOR REFERENCE

THIS IS THE INTERNAL POTENTIOMETERTHIS POTENTIOMETER CAN BE ADJUSTED FOR SINGLE SPEED SETTING OR MAX SPEED SELECTION

THIS LINK/JUMPER SHOULD BE REMOVEDWHEN USING AN EXTERNAL POTENTIOMETEROR EXTERNAL CONTROL SIGNAL CONNECTEDTO "ST1"

THE ABOVE DIAGRAM SHOWS "ST1".

"ST1" CONNECTIONS ARE CLASSED AS"CUSTOMER/USER CONNECTIONS".

GND = COMMON•+ = VDC OUTPUT AS SET BY•

INTERNAL POTENTIOMETERE1 = 0-10VDC INPUT•

149-CD-POT

10/07/2018MK-149-CD-POT Issue: Saved Date:A

All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. 149-CD-POT Issue A: 10.07.2018Check the individual product accessories table for fan controller compatibility.

Please note: This is an estimated adjustment guide

149-CD-POT The 149-CD-POT is a commissiong device designed to be used with our EC range of fans. This device will be as standard with our box fan range from May 2018. The device will allow the for the installer to set the maximum operating speed of the fan that it is connected to. The installer or commissioning engineer can adjust the fan speed using the potentiometer built onto the 149-CD-POT board. This potentionmeter can either be used for single speed adjustment or to set a maximum speed for the fan to operate at when an external control source is used. If external speed control is required, the jumper connection next to the potentionmeter on the board would need to be removed, the installer can then connect to ST1 (using the diagram provided). When an external speed control is fitted, the maximum speed setting available to the external control is limited by the potentiometer setting of the commissioning device.


Installation InstructionsQUIETFLOW SQS EC

Table 1: Operational Maintenance

Activity Frequency

Inspect AV mounts for Corrosion or “Sag” 6 months

Check earth bonding 6 months

Dampers check rubber stops and grease (lithium based) pivot points, by removing plastic caps Yearly

Check fixings tightness and conditions of brass track and rivets 26,000 hours / 3 years

Inspect and clean impeller 26,000 hours / 3 years

Remove dirt from motor cooling fins 26,000 hours / 3 years

Check operation of anti-condensation heaters 26,000 hours / 3 years

Check for even tip clearance between impeller and casing – For ATEX 10% of motor shaft diameter with 2mm minimum and 13mm maximum. 26,000 hours / 3 years

Check motor Amps 26,000 hours / 3 years

Any corrosion - treat with suitable chemicals 26,000 hours / 3 years

Check casing seals 26,000 hours / 3 years

Table 2: Terminal Box Maintenance

Activity Frequency

Check that lid seal is in place and not damaged Each time the enclosure is opened

Check that lid fixing screws are in place and secured Each time the enclosure is closed

Check that the mounting bolts are tight and free from corrosion Annually

Check security of all cable glands Annually

Check that all screw clamps terminals are secure Annually and each time enclosure is opened

Check enclosure for damage Annually

5.0 Storage5.1 If the fan is not to be used immediately then it should be stored in a clean, dry, vibration free and lockable location.5.2 The impeller must be spun by hand (ensuring that it does not come to rest in the same position) on a monthly basis to prevent hardening of the grease and possible damage to the bearings.5.3 All items to be stored on pallets that afford adequate protection from damage, dust and high humidity.5.4 If storage periods of longer than 1 month are anticipated then Elta (or their Agent) should be contacted prior to storage taking place, to ensure the storage area provisions will not be detrimental to the well being of Elta products.

6.0 Guarantee Elta Fans Ltd will, free of charge, within a period of 1 year from the date of dIspatch from their works, repair or at its option replace any goods which are proved to have defects as a result of defective materials or workmanship. The goods MUST be returned to Elta Fans Ltd carriage paid for examination.


Wiring DiagramsQUIETFLOW SQS

EC

Please use the table(s) below to match up the product code and the wiring diagram number.

Single Phase 200V - 277V / 50Hz or 60Hz

Three Phase 380V - 480V / 50Hz or 60Hz

PageNo.

Product Code

Wiring Diagram No.

8 SQS100-1ECL 152-00036

8 SQS125-1ECL 152-00036

8 SQS150-1ECL 152-00036

9 SQS200-1ECL 152-00036

10 SQS250-1ECL 152-00036

10 SQS315-1ECL 152-00298951

10 SQS400-1ECL 152-MOEA03K1


PageNo.

Product Code

Wiring Diagram No.



Wiring Diagrams152-00044 EC

FAN C/W POTENTIOMETER SPEED CONTROL (149-POT-10)

200-277V 1PH 50/60HzSUPPLY

149-POT-10

57 621

GREE

N/YE

LLOW

BLUE

BROW

N

WHI

TE

WHI

TE

RED

GREE

N

BLUE

GREY

YELL

OW

WHI

TE

TO MOTOR

FAN

NL E1 A1GND10V

L N

11 14 A2D1

GREE

N

RED

WHI

TE

WHI

TE

GREY

BLUE

WHI

TE

YELL

OW

BROW

N

BLUE

GREE

N/YE

LLOWTO MOTOR


FAN ONLY

FAN

D1 A21411

NL

10V GND A1E1L N

ALL WIRING AND CONTROL EQUIPMENT MUST COMPLY TO THELATEST IEE REGULATIONS, IN PARTICULAR PART 552-01-02/03

11/07/2013MK-152-00044 Issue: Saved Date:C

All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. MK-152-00044 Issue C: 11.07.2013Check the individual product accessories table for fan controller compatibility.



BLUE

RED

WHI

TE

YELL

OW

BROW

N

BLUE

GREE

N/YE

LLOW

TO MOTOR


FAN ONLY

FAN

NL E1 A1 GND 10V

L N


NL E1 A1 GND 10V

1 2 7 6 5

L N

RED

BLUE

WHI

TE

YELL

OW

BROW

N

BLUE

GREE

N/YE

LLOW

149-POT-10

TO MOTOR


FAN


11/07/2013MK-152-00036 Issue: Saved Date:C



Wiring Diagrams152-00036-CD EC

20/06/2018MK-152-00036-CD Issue: Saved Date:B

ALL WIRING AND CONTROLS EQUIPMENT MUST COMPLY TO THE

LATEST IET REGULATIONS, IN PARTICULAR PART 552-01-02/03

JUMPERREMOVED*

MAX SPEEDTRIMMER

NOTE:*JUMPER REMOVED WHEN EXTERNALCONTROL SOURCE IS USED.

PENL

POW

ERCO

NTRO

LS

RED

BLUE

WHITE

YELLOW

G/Y

BLUE

BROWN

200 - 277V 1PH 50HzMAINS SUPPLY

SH100-1ECLSH125-1ECLSH150-1ECLSH200-1ECLSH250-1ECLSH315-1ECL

LN

SINGLE FAN

1PH EC SINGLE FAN C/W 149-CD-POT & 149-POT-10

BLUE

BROW

N

GREE

N/YE

LLOW

1

149-POT-10

5672

GND 10V E1

MIN MAX

E1GND

ST1

ST2

149-CD-POT

A1GN

D10

VE1

FOR USE WITH:SQS100-1ECLSQS125-1ECLSQS150-1ECLSQS200-1ECLSQS250-1ECL

SSDR200-1ECSSDR250L-1ECSSDR250H-1EC

REMOVE LINK WHEN USINGEXTERNAL POTENTIOMETER OREXTERNAL CONTROL SIGNAL

POTENTIOMETER FOR SINGLESPEED ADJUSTMENT OR MAXSPEED SELECTION

PENL

POW

ERCO

NTRO

LS

RED

BLUE

WHITE

YELLOW

G/Y

BLUE

BROWN


SH100-1ECLSH125-1ECLSH150-1ECLSH200-1ECLSH250-1ECLSH315-1ECL

LN

SINGLE FAN

1PH EC SINGLE FAN C/W 149-CD-POT

BLUE

BROW

N

GREE

N/YE

LLOW

GND 10V E1

MIN MAX

E1GND

ST1

ST2

149-CD-POT

A1GN

D10

VE1

FOR USE WITH:SQS100-1ECLSQS125-1ECLSQS150-1ECLSQS200-1ECLSQS250-1ECL

SSDR200-1ECSSDR250L-1ECSSDR250H-1EC

All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. MK-152-00036-CD Issue B: 20.06.2018Check the individual product accessories table for fan controller compatibility.


Wiring Diagrams152-104A EC

THERMAL CUT-OUTCONNECT TOCONTROL CIRCUIT

L/U1

N/U2Z1Z2TBTB

THERMAL CUT-OUTCONNECT TOCONTROL CIRCUIT

L/U1

N/U2Z1Z2TBTB

CONTROLLER TERMINAL BOX

EL N

NLENL AUX

FAN

L E

230V 1PH 50Hz SUPPLY

N

104A - CLOCKWISE

FAN C/W TRANSFORMER SPEED CONTROL (149-TC1_)

FAN



BLAC

K

WHI

TE

ORAN

GE

BROW

N

BLUE

GREE

N/YE

LLOW

WHI

TE

BROW

N

BLUE

C

1

5

6

7

8

9

A3DRAWING No.

SHEET OF ISSUE

DRAWN BY

DATE

SCALE STATUS

APPROVED

CHECKEDELTA FANS LTD,17 BARNES WALLIS ROAD,SEGENSWORTH INDUSTRIAL ESTATE,FAREHAM, HAMPSHIRE. PO15 5ST.Tel. 01489 566500 Fax. 01489 566555

Elta Fans Ltd. own the copyright of this drawing/

in writing from its owners Elta Fans Ltd.and must not be reproduced without permission

con�dence and which must not be used for anyspeci�cation document which is supplied in

C

FINISH

MATERIAL

SPECIFICATION

DIMENSIONS ARE IN mm UNLESS STATED OTHERWISE

THIS IS A C.A.D. PRODUCED DRAWINGAND THEREFORE NO SUBSEQUENTMANUAL MODIFICATIONS WILL BE

ALLOWED.

TITLE

UNLESS OTHERWISE STATED.

BYISS CN.

DATE CHKD

ISS CN. BY

DATE CHKD

ISS CN. BY

DATE CHKD

ISS CN. BY

DATE CHKD

A

1

B C D E

A C D E

1 1 E

18-10-11

DM

-

I

USED ON

OF THESE VIEWS FOR MANUFACTURINGPURPOSES ARE AT SUPPLIERS RISK.

REFERENCE PURPOSES ONLY. USE

ANY DEVELOPMENT VIEWS SHOWN ONTHIS DRAWING ARE SHOWN FOR

ORIENTATION OF FAN MUST BE AS PERDRAWING OR REFER TO ELTA

A3

GENERAL ā 2.0DUCT CASING LENGTH ā 0.5%BELL CASING DIMENSIONS ā 5.0mm

TOLERANCES

152-104Apurpose other than that for which it is supplied

B

NTS

2

3

4

10

9

8

7

6

5

4

3

2

1

10

C

N/A

N/A

N/A

DMO

DM07/06/2012

DMOK0006RENAMED FROM152-104

D

DM02/05/2012

AWMUPDATED TERMINAL PINTO SHOW ACTUALLOCATION

C

21/11/2011

DMOREMOVED 104XBCOUNTER-CLOCKWISEDRAWING

B

PG03/11/17

LINE AND NEUTRAL RE-ORDERED

ELECTRONIC CONTROLREMOVED

PBK0185E

1 PH MOTOR WITH CAPACITORAND VARIOUS CONTROL OPTIONS

All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. MK-152-104A Issue E: 03.11.2017Check the individual product accessories table for fan controller compatibility.



WHI

TE

WHI

TE

ORAN

GE

BROW

N

RED

BLUE

GREY

BLAC

K

GREE

N/YE

LLOW

BROW

N

BLAC

K

GREY

BROW

N

BLAC

K

GREY

GREY

RED

WHI

TE

WHI

TE

ORAN

GE

BLAC

K

BLUE

BROW

N

GREE

N/YE

LLOW

TO REVERSE ROTATION SWAP ANY TWO INCOMING SUPPLY CABLES

FAN ONLY

LOW SPEED STAR CONNECTION

L3L2

W1V2V1U2TB TB W2 U1

L1 PE

PEL3L2

W1V2V1U2TB TB W2 U1

L1

TO MOTOR

TO MOTOR

HIGH SPEED DELTA CONNECTION

FAN C/W STAR/DELTA SWITCH

U1W2TBTB U2 V1 V2 W1

FAN TERMINAL BOX

STAR/DELTASWITCH

2 3 6 7 8

W1V2W2U2V1U1

L3L2L1

1514129

L2

WV EL1 L2 L3 U

L1 L3 E

380-440V 3PH 50HzSUPPLY



FAN TERMINAL BOX

GREY

BLAC

K

BROW

N

BROW

N

BLAC

K

GREY

GREE

N/YE

LLOW

W1V2V1U2TB TB W2 U1


11/07/2013MK-152-108 Issue: Saved Date:D

All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. MK-152-108 Issue D: 11.07.2013Check the individual product accessories table for fan controller compatibility.



TO MOTOR


220-240V 1PH 50HzSUPPLY

EL N

NLENL AUX

N/U2

L/U1

N/U2

L/U1

FAN ONLY

TO MOTOR


L N PE


FAN


GREE

N/YE

LLOW

BLUE

OR G

REY

BLAC

K

BROW

N

GREE

N/YE

LLOW

BLUE

OR G

REY

BLAC

K

BROW

N

BROW

N

BLUE

C

MK-152-177 Issue: C Saved Date: 03/11/17




4321

10V D1E1GND


L N

1411NL1

5

1 2

GREE

N/YE

LLOW

3 4

TO MOTOR

FAN

1 2 67 5


149-POT-10

A1

A1

FAN

FAN ONLY

TO MOTOR43

GREE

N/YE

LLOW

21 54321

L1 N 11 14 D1E1GND10V

NL



C

A3DRAWING No.

SHEET OF ISSUE

DRAWN BY

DATE

SCALE STATUS

APPROVED

CHECKEDELTA FANS LTD,17 BARNES WALLIS ROAD,SEGENSWORTH INDUSTRIAL ESTATE,FAREHAM, HAMPSHIRE. PO15 5ST.Tel. 01489 566500 Fax. 01489 566555

Elta Fans Ltd. own the copyright of this drawing/

in writing from its owners Elta Fans Ltd.and must not be reproduced without permission

con�dence and which must not be used for anyspeci�cation document which is supplied in

C

DIMENSIONS ARE IN mm UNLESS STATED OTHERWISE

BYISS CN.

DATE CHKD

ISS CN. BY

DATE CHKD

ISS CN. BY

DATE CHKD

ISS CN. BY

DATE CHKD

A C D E

1 1 A

19-12-13

DM

-

I

A3152-00298951

purpose other than that for which it is supplied

B

NTS

10

C

AWM

DMO05-03-14

NEW DRAWING SEECHANGE NOTE FOR DETAILS.

MBK0091A

All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. MK-152-00298951 Issue A: 05.03.2013Check the individual product accessories table for fan controller compatibility.


Wiring Diagrams152-00298951-CD EC

20/06/2018MK-152-00298951-CD Issue: Saved Date:B

ALL WIRING AND CONTROLS EQUIPMENT MUST COMPLY TO THELATEST IET REGULATIONS, IN PARTICULAR PART 552-01-02/03

CONT

ROL


FOR USE WITH:SQS315-1ECLSSDR315-1EC

JUMPERREMOVED*

MAX SPEEDTRIMMER

E110

VGN

DD1

A1

149-CD-POTST2

ST1

GND E1

MAXMIN

E110VGND

2 7 6 5

149-POT-10

1

GREE

N/YE

LLOW

BROW

N

BLUE


SINGLE FAN

1411

NL

L N PE

1

2

G/Y

4

3

POW

ER

2

1

4

3

5


5

3

4

1

2

POW

ER

3

4

G/Y

2

1

PENL

LN

1114

SINGLE FAN


BLUE

BROW

N

GREE

N/YE

LLOW

GND 10V E1

MIN MAX

E1GND

ST1

ST2

149-CD-POT

A1D1

GND

10V

E1



FOR USE WITH:SQS315-1ECLSSDR315-1EC


CONT

ROL

All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. MK-152-00298951-CD Issue B: 20.06.2018Check the individual product accessories table for fan controller compatibility.


All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. MK-152-MOEA03K1 Issue D: 18.07.2013Check the individual product accessories table for fan controller compatibility.

Wiring Diagrams152-MOEA03K1 EC


L N

24V 10V GND D1 E1 1411 NL1

1 2 3 4 5

GREE

N/YE

LLOW

1 2

GREE

N/YE

LLOW

3 4

TO MOTOR

FAN ONLY

FAN

L N

149-POT-10

10V GND D1 E124V


1 2 3 4 5

GREE

N/YE

LLOW

1 2

GREE

N/YE

LLOW

3 4TO MOTOR

FAN


57 621

L1 N11 14


18/07/2013MK-152-MOEA03K1 Issue: Saved Date:D



CONT

ROL


FOR USE WITH:SQS400-1ECLSQS500-1ECL

SSDR400-1ECSSDR500-1EC



GND

10V

D1E1

149-CD-POTST2

ST1

GND E1

MAXMIN

E110VGND

GREE

N/YE

LLOW

BROW

N

BLUE


SINGLE FAN

1411

NL

L N PE

1

2

G/Y

4

3

POW

ER

2

1

4

3

5

G/Y

24V

CONT

ROL


FOR USE WITH:SQS400-1ECLSQS500-1ECL

SSDR400-1ECSSDR500-1EC

JUMPERREMOVED*

MAX SPEEDTRIMMER

GND

24V

10V

D1E1

149-CD-POTST2

ST1

GND E1

MAXMIN

E110VGND

2 7 6 5

149-POT-10

1

GREE

N/YE

LLOW

BROW

N

BLUE


SINGLE FAN

1411

NL

L N PE

1

2

G/Y

4

3

POW

ER

2

1

4

3

5

G/Y


20/06/2018MK-152-MOEA03K1-CD Issue: Saved Date:BAll wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. MK-152-MOEA03K1-CD Issue B: 20.06.2018Check the individual product accessories table for fan controller compatibility.

Wiring Diagrams152-MOEA03K1-CD EC


All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. MK-152-MOEA03K3 Issue D: 18.07.2013Check the individual product accessories table for fan controller compatibility.

Wiring Diagrams152-MOEA03K3 EC

L1 L3

149-POT-10

L2

10V GND D1 E124V


1 2 3 4 5

GREE

N/YE

LLOW

1 2

GREE

N/YE

LLOW

3 4 5

TO MOTOR

FAN


57 621

L1 L2 L311 14


L1 L2 L3

24V 10V GND D1 E1 1411 L3L2L1

41 2 3 4 5

GREE

N/YE

LLOW

1 2

GREE

N/YE

LLOW

3 5

TO MOTOR

FAN ONLY

FAN


18/07/2013MK-152-MOEA03K3 Issue: Saved Date:D


All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. MK-152-MOEA03K3-CD Issue B: 20.06.2018Check the individual product accessories table for fan controller compatibility.

Wiring Diagrams152-MOEA03K3-CD EC


E1

5

BLAC

K

GREY

L3

L3L2

5

3

4

1

2

POW

ER

3

4

G/Y (X2)

2

1

PEL2L1

L111

14

SINGLE FAN


BROW

N

GREE

N/YE

LLOW

1

149-POT-10

5672

GND 10V E1

MIN MAX

GND

ST1

ST2

149-CD-POT

E1D1

10V

24V

GND

MAX SPEEDTRIMMER

JUMPERREMOVED*

FOR USE WITH:SQS500-3ECL

SSDR500-3EC

380-480V 3PH 50HzMAINS SUPPLY

CONT

ROL


5

BLAC

K

GREY

L3

L3L2

5

3

4

1

2

POW

ER

3

4

G/Y (X2)

2

1

PEL2L1

L111

14

SINGLE FAN


BROW

N

GREE

N/YE

LLOW

GND 10V E1

MIN MAX

E1GND

ST1

ST2

149-CD-POT

E1D1

10V

24V

GND



FOR USE WITH:SQS500-3ECL

SSDR500-3EC380-480V 3PH 50Hz

MAINS SUPPLY

CONT

ROL

20/06/2018MK-152-MOEA03K3-CD Issue: Saved Date:B


EU Declaration of Conformity Declaration of Incorporation

Description of Equipment:Building Services Ranges - Air movement fan

Equipment model numbers for safe area fans:SCP, SPA, SAX, SCD, SDA, SCC, SLC, SCPP, SPP, SAMF, HIT, SEM, SEL, ISEO IMF, SH, SSD, SQS, SQSDCV, SQU, SMB, STD, SQT, SQTDCV, SCH, SCHT, SSDR, SSDRDCV, STDR, STDRDCV, SB, SQU-HT, SSQU-HT, SDF, ZFHIC, SRC, SRC, CF, TF, SSRL, BLB, BLTF

Relevant / applied directives:Machinery directive 2006/42/EC, Low voltage directive 2014/35/EU

Relevant / applied directives where applicable:Energy related products directive 2009/125/EC (when used in Europe)Electromagnetic compatibility directive 2014/30/EU (where driven via Inverter)RoHS 2011/65/EU and its amendments (including Directive 2015/863/EU)

Relevant / applied directives where applicable:BS EN ISO 12100 : 2010BS EN 14694 : 2003 + A1 : 2011BS EN 308:1997BS EN ISO 5801:2008

In accordance with the Machinery Directive 2006/42/EC;

The design of the partly completed machine, listed above, complies with the Essential Health and Safety Requirements (EHSRs) of ANNEX I, sections 1.1.2, 1.1.5, 1.4.1, 1.5.1 in EC Machinery Directive 2006/42/EC.

Machinery is incomplete and must not be put into service until such time as the machinery which is partly complete, is to be incorporated, and has been assessed and Declared in Conformity with the provisions of any relevant parts of the Machinery Directive.

We undertake to transmit, upon reasoned request by appropriate national authorities, relevant information relating to the partly completed machinery identified above.

Manufacturer:Elta Fans Limited46 Third AvenuePensnett Trading EstateKingswinfordWest MidlandsDY6 7USUnited Kingdom

Date / Signature of Manufacturer: Document last revised: 20th July 2020

Name / Position of Signatory: Mr. Robert Rees Q.A.Manager Elta Fans LtdThis is an electronic document and is valid without a signature or date. ECD F Issue Status D

Herewith we declare that the air movement equipment below, on the basis of its design and construction as partly completed machines brought onto the market complies with relevant health and safety requirements of the EC Directives stated below. In the event that alterations are made to the machinery without prior consent from Elta Fans Ltd, this declaration becomes invalid.

EU Declaration of conformity/incorporation


NotesQUIETFLOW SQS

535-IOM0028 Issue C

eltafans.com

Tel +44 (0) 1384 275800Fax +44 (0) 1384 275810Email [email protected]

46 Third Avenue, Pensnett Trading Estate, Kingswinford, West Midlands, DY6 7US United Kingdom

Tel +44 (0) 1489 566500Fax +44 (0) 1489 566555Email [email protected] / [email protected]

17 Barnes Wallis Road, Segensworth East Industrial Estate, Fareham, Hampshire, PO15 5TT United Kingdom

Applied Technology & Building Services Export

Building Services

BS EN ISO 9001:2015 FM 556465

A member ofHEVAC ASSOCIATION

QUIETFLOW SQS - Amazon S3...3.0 Start Up 3.1 Before power is supplied to the unit, check that the...

Documents

Transcript of QUIETFLOW SQS - Amazon S3...3.0 Start Up 3.1 Before power is supplied to the unit, check that the...