Quidway AR 19-1X Router Hardware Configuration Manual _Overseas Version_V1

Hardware Configuration Manual of Quidway AR 19-1XS Series Routers (International Version) SECRET

2009-03-05 Huawei Confidential of 53

Huawei Technologies Co., Ltd.

Product Version Confidentiality Level

8048 V300R002 Secret

Product Name: Quidway AR 19-1X Series Router Total 53 pages

Hardware Configuration Manual of Quidway AR 19-1X Series Routers (Overseas Version)

V1.00

(For internal use only)

Huawei Technologies Co., Ltd. All Rights Reserved



Compiling Principles of the Configuration Manual: Make sure that the manual compiled according to the BOM list of the products. First, make a product list, and then detail the items in terms of configuration principles, configuration algorithms, and configuration precautions. The items available and unavailable, existing constraints, related product compatibility and requirements, and precautions for the marketing departments (highlighted in red) must be specified according to the actual R&D status, without exaggeration and "to-be-offered" advertisement. For any revisions in the documentation, identify the document version in the revision record, and clarify the additions, deletions and modifications compared with the last version. Guideline of the Configuration Manual template: This is the uniform template at the company level. It is allowed to make proper reconstruction and modification according to the characteristics of the products and the writing principles.



Revision Record

Date Revision Description Written by 2007-11-20 1.00 Version 1, including the modules supported

in phase one Zhang Huibin

2008-02-22 1.01 Modify the first version.Adopt SIC-FEF and SIC-GEC transceiver from purchasing code. Delete the selection of USB flash disks.

Zhang Gang



Table of Contents 1 Overview of AR 19-1X Series Routers .............................................................................. 10

1.1 Introduction to Products ....................................................................................... 10 1.2 Networking of the Quidway AR 19-1X Series .................................................... 10 1.3 Appearance of the Quidway AR 19-1X Series ................................................... 10

1.3.1 Appearance of Quidway AR 19-10 Router ................................................ 11 1.3.2 Appearance of Quidway AR 19-10-W Router ........................................... 11 1.3.3 Appearance of Quidway AR 19-13-I Router ............................................. 12 1.3.4 Appearance of Quidway AR 19-13-IW Router ......................................... 13 1.3.5 Appearance of Quidway AR 19-15-I Router ............................................. 13 1.3.6 Appearance of Quidway AR 19-15-IW Router ......................................... 14

1.4 Basic Configuration of the Quidway AR 19-1X Series ..................................... 15 1.4.1 System Description Table of the Quidway AR 19-1X Series ................ 15 1.4.2 Basic Configuration Description of the Quidway AR 19-1X Series .... 15

1.5 Introduction to the Host of the Quidway AR 19-1X Series .............................. 16 1.6 Introduction to the Interface Modules Supported by the Quidway AR 19-1X Series .............................................................................................................................. 17

1.6.1 Interface Modules Currently Supported ................................................... 17 1.6.2 Description of Interface Module Location ............................................... 19

1.7 Overall Configuration Principle of the Quidway AR 19-1X Series ................. 19 1.8 Overall Configuration Description of the Quidway AR 19-1X Series ............ 20

2 Host Configuration Description of the Quidway AR 19-1X Series ................................... 21 3 Description of Storage Media Expansion for the Quidway AR 19-1X Series ................. 23

3.1 Selection of USB Flash Memory .......................................................................... 23 4 Configuration of SIC Interface Module for the Quidway AR 19-1X Series ..................... 24

4.1 Configuration of the RT-SIC-1GEC Interface Module ....................................... 24 4.2 Configuration of the RT-SIC-4FSW Module and the RT-SIC-9FSW Interface Module ............................................................................................................................ 26 4.3 Configuration of the RT-SIC-1FEA Interface Module ....................................... 27 4.4 Configuration of the RT-SIC-1SAE Interface Module ....................................... 28 4.5 Configuration of the RT-SIC-1E1-F Module and the RT-SIC-EPRI Interface Module ............................................................................................................................ 29 4.6 Configuration of the RT-SIC-1FXS-V2 and RT-SIC-2FXS-V2 Interface Module .......................................................................................................................................... 31 4.7 Configuration of the RT-SIC-1FXO-V2 Module and the RT-SIC-2FXO-V2 Module ............................................................................................................................ 32 4.8 Configuration of the RT-SIC-1ADSL-I Interface Module .................................. 33 4.9 Configuration of the RT-SIC-1ADSL Interface Module..................................... 33 4.10 Configuration of the RT-SIC-1AM-V3 Interface Module ................................. 34 4.11 Configuration of the RT-SIC-1VE1 Interface Module ...................................... 34 4.12 Configuration of the RT-SIC-1BS-V2 Interface Module ................................. 36 4.13 Configuration of the RT-SIC-1BU-V2 Interface Module ................................. 37 4.14 Configuration of the RT-SIC-1BSV Module and the RT-SIC-2BSV Module 37



4.15 Configuration of the RT-SIC-1FEF Interface Module...................................... 38 4.16 Configuration of the RT-SIC-2FXS1FXO Interface Module ........................... 40

5 Configuration Description for External Cable Set of the Quidway AR 19-1X Series ..... 41 6 Configuration of External Cable Set of the Quidway AR 19-1X Series ........................... 46 7 Configuration Examples ..................................................................................................... 48 8 Configuration FAQ .............................................................................................................. 49

8.1 Although the routers have standard configurations without the need of on-site survey, in some of the bundled sales contracts, survey report is needed and some special requirements on the cable length are specified, especially the E1 cable. How to handle it? ..................................................................................................................... 49 8.2 The users complain that there is not any document in the package of the newly purchased E1 voice module, so they do not know how to use it. ............................... 50 8.3 The optical fibers that the marketing personnel promised to the customers are too long that we cannot find them in the configuration list. How can we do with it? ........ 50

9 Appendix: Slot Restriction for Host Interface Card ........................................................... 52 9.1 SIC/DSIC Configuration Table .............................................................................. 52 9.2 VPM Card Configuration Table ............................................................................. 53



Table of Figure Descriptions Figure 1 Front panel of the Quidway AR 19-10 router ................................................. 11 Figure 2 Back panel of the Quidway AR 19-10 router .................................................. 11 Figure 3 Front panel of Quidway AR 19-10-W router ................................................... 11 Figure 4 Back panel of the Quidway AR 19-10-W router ............................................ 12 Figure 5 Front panel of the Quidway AR 19-13-I router .............................................. 12 Figure 6 Back panel of the Quidway AR 19-13-I router .............................................. 12 Figure 7 Front panel of the Quidway AR 19-13-IW router .......................................... 13 Figure 8 Back panel of the Quidway AR 19-13-IW ...................................................... 13 Figure 9 Front panel of Quidway AR 19-15-I router .................................................... 14 Figure 10 Back panel of the Quidway AR 19-15-I router ............................................ 14 Figure 11 Front panel of the Quidway AR 19-15-IW router......................................... 14 Figure 12 Back panel of the Quidway AR 19-15-IW router ......................................... 15 Figure 13 Extension of 75Ω E1 cable ........................................................................... 49 Figure 14 Extension of 120Ω E1 cable ......................................................................... 50



Table of Table Descriptions Table 1 System description table of the Quidway AR 19-1X series ....................... 15 Table 2 System description table of the main board of the Quidway AR 19-1X series 15 Table 3 Quidway AR 19-1X series router code ........................................................ 16 Table 4 Quidway AR 19-1X series host code ........................................................... 16 Table 5 SIC module table of the Quidway AR 19-1X series ................................... 17 Table 6 Built-in module table of the Quidway AR 19-1X series .............................. 18 Table 7 Host code of the Quidway AR 19-1X series ............................................... 21 Table 8 Configuration list of the RT-SIC-1GEC module .......................................... 24 Table 9 Configuration list of the RT-SIC-1GEC SFP module .................................. 25 Table 10 Configuration list of the single-mode cables for the RT-SIC-1GEC module 26 Table 11 Configuration list of the multi-mode cables for the RT-SIC-1GEC module 26 Table 12 The configuration list of the RT-SIC-4FSW module and the RT-SIC-9FSW module 27 Table 13 Configuration list of the RT-SIC-1FEA module ........................................... 28 Table 14 Configuration list of the RT-SIC-1SAE module ........................................... 28 Table 15 Configuration List of Optional Cables for the RT-SIC-1SAE Module ........ 29 Table 16 Configuration of the RT-SIC-1E1-F module and the RT-SIC-EPRI module 30 Table 17 Cable Configuration of the RT-SIC-1E1-F module and the RT-SIC-EPRI module 30 Table 18 Configuration list of RT-SIC-1FXS-V2 and RT-SIC-2FXS-V2 ................... 32 Table 19 Configuration list of RT-SIC-1FXO-V2 and RT-SIC-2FXO-V2 .................. 32 Table 20 Configuration list of the RT-SIC-1ADSL-I module ...................................... 33 Table 21 Configuration list of the RT-SIC-1ADSL module ........................................ 33 Table 22 List of the Optional Accessories for the RT-SIC-1ADSL ............................ 34 Table 23 Configuration list of the RT-SIC-1AM-V3 module ....................................... 34 Table 24 Configuration list of the R T-SIC-1VE1 module .......................................... 35 Table 25 Cable configuration list of the R T-SIC-1VE1 module ................................ 35 Table 26 Configuration list of the RT-SIC-1BS-V2 module ....................................... 37 Table 27 Configuration list of the RT-SIC-1BU-V2 module ....................................... 37 Table 28 Configuration list of RT-SIC-1BSV and RT-SIC-2BSV ............................... 38 Table 29 Configuration list of the RT-SIC-1FEF module ........................................... 38 Table 30 Configuration list of the RT-SIC-1FEF SFP optical module ....................... 39 Table 31 Configuration list of the single-mode cables for the RT-SIC-1FEF module 40 Table 32 Configuration list of the multi-mode cables for the RT-SIC-1FEF module 40 Table 33 Configuration list of the RT-SIC-2FXS1FXO module ................................. 40 Table 34 Configuration list for external cable set of the Quidway AR 19-1X series 41 Table 35 Fiber optical suite of the Quidway AR 19-1X series ................................... 46



Table 36 SIC/DSIC configuration table of the Quidway AR 19-1X series ................ 52 Table 37 VPM configuration table of the Quidway AR 19-1X series ........................ 53



Hardware Configuration Manual of Quidway AR 19-1X Series Routers (International Version) V1.01

Keywords: Hardware Configuration Manual of Quidway AR 19-1X Series Routers Hardware (International Version) Abstract: This document describes the configuration of Quidway AR 19-1X series routers (international version) to facilitate product configuration and ensure correct networking and delivery. Document Management: This document was prepared by the 8040 PDT unit based on the current release of the product. It will be updated based on the builds of the product. The R&D, Marketing, Technical Support functions have participated in the review of the document. The first draft of the document will be available at the application stage of the pilot office. It will be updated regularly in the future (at least once in a quarter, identified with the version number and the release date of the document). This document is included in the configuration management. Reviewed and approved by related units, the document will be archived in the R&D Documentation Center. At the same time, it will be released through the database of the "Marketing and Technical Documents Platform". The contact persons of related units in charge of documentation should keep the document secret and should not distribute it without proper permission. Document Usage: This document is supposed to be used in connection with Quidway AR 19-1X Series Router Overview, mainly for guiding the configuration and delivery activities of the marketing and production functions. It is a secret document only for internal use, and will not be distributed to the regional offices directly. The marketing function will prepare the Product Sales Guide based on this document, keep it updated dynamically, and distribute it to the regional offices. This document should not be released to the customers or disclosed to Huawei’s competitors, otherwise related departments and individuals shall be held responsible. The opinions and suggestions deriving from the use of the document can be delivered through the Marketing and Technical Documents Platform in a timely fashion to facilitate future revision by the 8040 PDT unit. Announcement: This document has responded to the principle of Company-Level Uniform Product Naming of Routers, and has it reflected in the text. The names of some of the modules in the PDM or the corresponding finished boards or components still carry the attributes of the previous naming rules, however. Before the data center makes unified revisions to it, if there are inconsistencies between this document and the related descriptions in the PDM, the codes of the corresponding parts in this document shall be based on.



1 Overview of AR 19-1X Series Routers

1.1 Introduction to Products

Quidway AR 19-1X series routers (hereafter referred to as the Quidway AR 19-1X series) belong to Quidway AR 1900 series routers family. The Quidway AR 1900/2900/4900 series router is a new generation of the AR series router of Huawei after Huawei has successfully developed the R series and the AR 18/28/46 series router. The routers in this series have incorporated all-round upgrades and enhancements based on the hardware and software of the original router products, having greatly improved the cost effectiveness of the router products and their ability to integrate multiple services. This series is also divided into three series: AR 1900, AR 2900, and AR 4900, moving up one after another along the value chain. AR 1900 and AR 2900 series routers can be used as edge access of major networks and networks of the operators, as the core routers for branch offices or small businesses. AR 4900 series routers can be used as the core routers of the networks of large and medium-sized enterprises, or as the edge or converged access equipment for major networks or networks of the operators. Quidway AR 1900/2900/4900 series routers use the network operating system platform of Huawei (VRP V5). The network operating system fully supports software features of the existing R series and AR 18/28/46 series products, providing backup solutions based on the backup center technology and VRRP, MPLS L3/L2 VPN, ADSL access, PPPoE Server/Client, IP multi-cast, and Quality of Service (QoS). At the same time, the VRP V5 operating system also fully supports IPv6 protocol and various other features. In addition, the hardware and software of AR 1900/2900/4900 series routers meet international standards, which ensures the interconnection with products from other vendors at different levels and can protect the existing investment of the users to the maximum extent possible. AR 1900 series routers are the low-end products of the new generation of the AR series routers. They are inferior to AR 2900/4900 series products in terms of the transmission performance, the encryption performance, and the interface density, mainly targeting SMBs, Internet cafes, government organizations, and branch offices in special industries. AR 1900 series routers support a wide range of optional interfacing modules, offering the flexibility and scalability in networking. This document describes configurations of Quidway AR 19-10, Quidway AR 19-10-W, Quidway AR 19-13-I, Quidway AR 19-13-IW, Quidway AR 19-15-I, and Quidway AR 19-15-IW. Quidway AR 19-10, Quidway AR 19-10-W, Quidway AR 19-13-I, Quidway AR 19-13-IW, Quidway AR 19-15-I, and Quidway AR 19-15-IW routers are boxes with 1U height. Quidway AR 19-10, Quidway AR 19-10-W, Quidway AR 19-13-I, Quidway AR 19-13-IW, Quidway AR 19-15-I, and Quidway AR 19-15-IW are the same in physical dimension, and those ended with "W" support WLAN function. Based on Quidway AR 19-10, Quidway AR 19-13-I is added with a 4-line G.SHDSL upstream interface and Quidway AR 19-15-I is added with one ADSL2+ upstream interface. Quidway AR19-1X has only one SIC/DSIC slot, so one SIC/DSIC can be configured on one router. The interface module available for Quidway AR 19-1X can also be used in the SIC slot of AR 19-61, AR29-01/21/41, and AR49-45 routers.

1.2 Networking of the Quidway AR 19-1X Series

Refer to Product Overview of Quidway AR 19-1X Series Routers.

1.3 Appearance of the Quidway AR 19-1X Series

Quidway AR 19-10, Quidway AR 19-10-W, Quidway AR 19-13-I, Quidway AR 19-13-IW, Quidway AR 19-15-I, and Quidway AR 19-15-IW are the same in physical dimensions, and those ended with "W" support WLAN function. Based on Quidway AR 19-10, Quidway AR



19-13-I is added with a 4-line G.SHDSL upstream interface and Quidway AR 19-15-I is added with one ADSL2+ upstream interface.

1.3.1 Appearance of Quidway AR 19-10 Router

The Quidway AR 19-10 router is in 1U height. One USB interface, four LEDs, one reset switch and one AC power interface are on the front panel. One fixed 10/100M Ethernet interface, one SIC/DSIC slot, four fixed 10/100M Ethernet interfaces and one CON/AUX interface are on the back panel. The appearance of the Quidway AR 19-10 router is shown below. 1. Front panel of the Quidway AR 19-10 router

Figure 1 Front panel of the Quidway AR 19-10 router

2. Back Panel of the Quidway AR 19-10 router

Figure 2 Back panel of the Quidway AR 19-10 router

1.3.2 Appearance of Quidway AR 19-10-W Router

The Quidway AR 19-10-W router is in 1U height. One USB interface, four LEDs, one reset switch and one AC power interface are on the front panel. One fixed 10/100M Ethernet interface, one SIC/DSIC slot, four fixed 10/100M Ethernet interfaces, one CON/AUX interface and a pair of antennas for the network card of WLAN are on the back panel. One built-in mini PCI plug-in card of WLAN is in the Quidway AR 19-10-W router. The appearance of the Quidway AR 19-10-W router is shown below. 1. Front panel of the Quidway AR 19-10-W router

Figure 3 Front panel of Quidway AR 19-10-W router



2. Back panel of the Quidway AR 19-10-W router

Figure 4 Back panel of the Quidway AR 19-10-W router

1.3.3 Appearance of Quidway AR 19-13-I Router

The Quidway AR 19-13-I router is in 1U height. One USB interface, seven LEDs, one reset switch and one AC power interface are on the front panel. One fixed 10/100 M Ethernet interface, one SIC/DSIC slot, one 4-line G.SHDSL upstream interface, four fixed 10/100 M Ethernet interfaces, one ISDN BRI S/T interface and one CON/AUX interface are on the back panel. The appearance of the Quidway AR 19-13-I router is shown below. 1. Front panel of the Quidway AR 19-13-I router

Figure 5 Front panel of the Quidway AR 19-13-I router

2. Back panel of the Quidway AR 19-13-I router

Figure 6 Back panel of the Quidway AR 19-13-I router



1.3.4 Appearance of Quidway AR 19-13-IW Router

The Quidway AR 19-13-IW router is in 1U height. One USB interface, seven LEDs, one reset switch and one AC power interface are on the front panel. One fixed 10/100 M Ethernet interface, one SIC/DSIC slot, one 4-line G.SHDSL upstream interface, four fixed 10/100 M Ethernet interfaces, one ISDN BRI S/T interface, one CON/AUX interface and a pair of antennas for the network card of WLAN are on the back panel. One built-in mini PCI plug-in card of WLAN in Quidway AR 19-10-W router and one VPM stick interface for upgrading. The appearance of the Quidway AR 19-13-IW router is shown below. 1. Front panel of the Quidway AR 19-13-IW router

Figure 7 Front panel of the Quidway AR 19-13-IW router

2. Back panel of the Quidway AR 19-13-IW router

Figure 8 Back panel of the Quidway AR 19-13-IW

1.3.5 Appearance of Quidway AR 19-15-I Router

The Quidway AR 19-15-I router is in 1U height. One USB interface, seven LEDs, one reset switch and one AC power interface are on the front panel. One fixed 10/100 M Ethernet interface, one SIC/DSIC slot, one ADSL2+ over POTS upstream interface, four fixed 10/100 M Ethernet interfaces, one ISDN BRI S/T interface, one CON/AUX interface are on the back panel. The appearance of the Quidway AR 19-15-I router is shown below.



1. Front panel of the Quidway AR 19-15-I router

Figure 9 Front panel of Quidway AR 19-15-I router

2. Back panel of the Quidway AR 19-15-I router

Figure 10 Back panel of the Quidway AR 19-15-I router

1.3.6 Appearance of Quidway AR 19-15-IW Router

The Quidway AR 19-15-IW router is in 1U height. One USB interface, four LEDs, one reset switch and one AC power interface are on the front panel. One fixed 10/100 M Ethernet interface, one SIC/DSIC slot, one ADSL2+ over POTS upstream interface, four fixed 10/100 M Ethernet interfaces, one ISDN BRI S/T interface, one CON/AUX interface and a pair of antennas for the network card of WLAN are on the back panel. One built-in mini PCI plug-in card of WLAN in Quidway AR 19-15-IW router and one VPM insertion piece interface for upgrading. The appearance of the Quidway AR 19-15-I router is shown below. Front panel of the Quidway AR 19-15-IW router

Figure 11 Front panel of the Quidway AR 19-15-IW router

Back panel of Quidway AR 19-15-IW router



Figure 12 Back panel of the Quidway AR 19-15-IW router

1.4 Basic Configuration of the Quidway AR 19-1X Series

1.4.1 System Description Table of the Quidway AR 19-1X Series

The Quidway AR 19-1X series in the Quidway AR 1900series shares one PCB, and the basic configuration is shown below.

Table 1 System description table of the Quidway AR 19-1X series

Item Description Slot 1 SIC/DSICPhysical dimensions (W ×D ×H)

300.0 mm × 240.0 mm × 49.1mm (including the plastic foot but excluding the rack-mounting ear)

Weight 2.5 kgInput voltage AC: 100V–240V (+/-10%) 50/60 Hz Maximum power 25 WWorking ambient temperature

0 °C–45 °C

Environment RH 5%–90% (non-condensing)

Table 2 System description table of the main board of the Quidway AR 19-1X series

Item Description Fixed interface One fixed FE

One CON/AUX interface Four fixed FE interfaces One USB interface

Processor PowerPC 333 MHzFlash 16 MBMemory 256 MB

1.4.2 Basic Configuration Description of the Quidway AR 19-1X Series

Quidway AR 1910 (AC) Basic model Model Number to the outside RT-AR1910-AC-OVS



Quidway AR 1910 (AC) Wireless model Model Number to the outside RT-AR1910-AC-OVS-W Quidway AR 1913 (AC) Basic model Model Number to the outside RT-AR1913-AC-OVS-I Quidway AR 1913 (AC) Wireless model Model Number to the outside RT-AR1913-AC-OVS-IW Quidway AR 1915 (AC) Basic model Model Number to the outside RT-AR1915-AC-OVS-I Quidway AR 1915 (AC) Wireless model Model Number to the outside RT-AR1915-AC-OVS-IW

Each router host possesses an independent 0235 code. The hosts of Quidway AR 19-10, Quidway AR 19-10-W, Quidway AR 19-13-I, Quidway AR 19-13-IW, Quidway AR 19-15-I, and Quidway AR 19-15-IW share a general top-level code 0105, as shown in the following table.

Table 3 Quidway AR 19-1X series router code

No. Code Description 1 0105A09M Quidway AR 19-1X Series Routers, International

Version

1.5 Introduction to the Host of the Quidway AR 19-1X Series

The Quidway AR 19-1X Series includes six hosts, which all use the AC power supply. The related codes and descriptions are summarized in the following table.

Table 4 Quidway AR 19-1X series host code

0105A09M item description: Datacom Device-Quidway AR 19-1X Series Routers-International Version

No. Code Description Quantity Remarks

1 0235A34D Assembly-Quidway AR 19-10-RTVZ31910-Router Host (AC)-International Version

At customers' option

Optional

2 0235A34E Assembly-Quidway AR 19-10-RTVZ31910-Router Host (AC)-WLAN-supported-International Version


Optional

3 0235A34F Assembly-Quidway AR19-13-RTVZ31913I-Router Host (AC)-International Version


Optional

4 0235A34G Assembly-Quidway AR 19-13-RTVZ31913IW –Router Host (AC)-WALN-supported-International Version


Optional

5 0235A34H Assembly-Quidway AR 19-15-RTVZ31915I-Router Host (AC)-International Version


Optional

6 0235A34J Assembly-Quidway AR 19-15-RTVZ31915IW-Router Host (AC)-WALN-supported-International Version


Optional



1.6 Introduction to the Interface Modules Supported by the Quidway AR 19-1X Series

1.6.1 Interface Modules Currently Supported

The Quidway AR 19-1X Series supports the SIC module as well as the built-in VPM module. For details, refer to "9 Appendix: Slot Restriction for Host Interface Card". All the SIC modules for the Quidway AR 19-1X series are in the SIC pack. The SIC pack and VPM module are put under the top-level code 0105A09M, parallel with the router host. The related codes and descriptions of SIC modules and VPM modules supported are as follows.

Table 5 SIC module table of the Quidway AR 19-1X series

0223A02F item description: Datacom Equipment-QuidwayAR 19/29/49 Router-Universal SIC Module

No. Code Description Acronym Remarks 1 0231A07M Functional module-Quidway AR

19-62-RTVM1S1GEC-1-port 10M/100M/1000M SIC module for electronic and optical Ethernet ports

RT-SIC-1GEC Optional

2 0231A644 Functional module-Quidway AR 49-65-RTVM1S4FSW-4 port 10M/100M Ethernet layer 2 switching module (RJ45)

RT-SIC-4FSW Optional

3 0231A07Y Functional module-Quidway AR 49-65-RTVM1S9FSW-9 port 10M/100M Ethernet layer 2 switching module (RJ45)

RT-DSIC-9FSW

Optional

4 0231A13S Functional module-Quidway AR 49-65-RTVM1S1VE1-1VT1-SIC module

RT-SIC-1VE1 Along with VPM

5 0231A30W Functional module-Quidway AR 49-65-RTVM1S1BS-1-port ISDN basic rate S/T interface SIC module

RT-SIC-1BS-V2

Optional

6 0231A30Y Functional module-Quidway AR 49-65-RTVM1S1BU-1-port ISDN basic rate U interface SIC module

RT-SIC-1BS-V2

Optional

7 0231A891 Functional module-Quidway AR 49-65-RTVM2S1BSV-1-port ISDN basic rate S/T voice interface SIC module

RT-SIC-1BSV Optional



9 0231A893 Functional module-Quidway AR 49-65-RTVM2S1FEF-1-port 100M SFP SIC module

RT-SIC-1FEF Optional

10 0231A894 Functional module-Quidway AR 49-65-RTVM2S2S1O-2FXS+1FXO voice SIC module

RT-SIC-2FXS1FXO

Optional

11 02311371 Functional module-QuidwayR1760-RTHM31FEA-1-port 10M/100M Ethernet electrical interface module (RJ45)

RT-SIC-1FEA Optional



No. Code Description Acronym Remarks 12 02312550 Functional

module-QuidwayR1760-RTHMN1SAE-1-port enhanced synchronous/asynchronous serial interface module

RT-SIC-1SAE Optional

13 02311804 Functional module-QuidwayR1760-RTHMLE1F-1-port non-channelized E1 interface module

RT-SIC-1E1-F Optional

14 02311374 Functional module-QuidwayR1760-RTHM6EPRI-1-port E1/CE1/PRI compatible interface module

RT-SIC-EPRI Optional

15 0231A08Q Functional module-QuidwayAR28-09-RTHM31FXS-1-port voice module user circuit interface board

RT-SIC-1FXS-V2

Optional

16 0231A08P Functional module-QuidwayAR28-09-RTHM32FXS-2-port voice module user circuit interface board

RT-SIC-2FXS-V2

Optional

17 0231A07S Functional module-QuidwayAR28-09-RTHM32FXO-1-port voice module ATO relay circuit interface module

RT-SIC-1FXO-V2

Optional

18 0231A07R Functional module-QuidwayAR28-09-RTHM32FXO-2-port voice module ATO relay circuit interface module

RT-SIC-2FXO-V2

Optional

19 0231A08M Functional module-QuidwayAR28-09-RTHM11ADI-1-port ADSL over ISDN interface card

RT-SIC-1ADSL-I

Optional

20 0231A08N Functional module-QuidwayAR28-09-RTHM11ADP-1-port ADSL over POTS interface card

RT-SIC-1ADSL

Optional

21 0231A39P Functional module-Quidway AR 28-09-RTHM31AM-1-port analog modem interface module

RT-SIC-1AM-V3

Optional

Table 6 Built-in module table of the Quidway AR 19-1X series

No. Code Description Acronym Remarks 1 0231A05P Functional module-Quidway AR

49-65-RTVM1VPM-32-line voice processing unit

RT-VPM32 Optional. Only AR913W and AR 19-15-IW are supported.

2 0231A24K Functional module-Quidway AR 49-65-RTVM1VPM-24-line voice processing unit

RT-VPM24 Optional. Only AR 19-13-IW and AR 19-15-IW are supported.

3 0231A24L Functional module-Quidway AR 49-65-RTVM1VPMA-16-line voice processing unit


4 0231A24M Functional module-Quidway AR 49-65-RTVM1VPMB-8-line voice processing unit




1.6.2 Description of Interface Module Location

For the Quidway AR 19-1X series, the requirement of the interface module location is as follows: VPM module is located inside the host of the router, and can only be installed by opening the chassis.

1.7 Overall Configuration Principle of the Quidway AR 19-1X Series

The Quidway AR 19-1X Series is the modular router, and can be configured with various interface modules as needed. The Quidway AR 19-1X Series has one SIC/DSIC slot and is available for one SIC/DSIC card. For details, refer to "9 Appendix: Slot Restriction for Host Interface Card". The structure of the current product list of the Quidway AR 19-1X series can accommodate the following two sales models: 1. Sale through agents This mode mainly refers to the contract with the distributors or the upgrade of the existing configuration. In this situation, the configuration is relatively simple. You only need to choose corresponding hosts, interface modules, and cables according to the contract for configuration. The configurations of hosts, interface modules, and cables are independent of each other. The operators need not consider the relationship between hosts, interface modules, and cables. 2. Tie-in sale with other products of the company In this model, the Quidway AR 19-1X series and other products of the company can be sold in networking applications. In this case, the salesperson just needs to select the needed host, interface modules and cables according to the contract, but they also need to consider the corresponding relationship between the host and its interfaces and cables. This mode also applies to the sporadic distribution of goods to customers. Some of the basic configuration principles are as follows: Important: The orders for the host of the Quidway AR 19-1X series must be coded and placed in the 0235xxxx category, not the 0105xxxx or 0303xxxx category. The orders for various SIC interface modules and VPM modules must be coded and placed in the 0231xxxx category, not in the 0105xxxx or 0303xxxx category. The interface modules for the Quidway AR 19-1X series need to be configured according to the specific requirement of the order. Multiple kinds of interface modules can be used for the Quidway AR 19-1X series. These interface modules can also be used for the AR 19-16, AR29-01/21/41, AR49-45 routers. In addition, there will also be new interface modules coming out one after another to meet different needs of the users. The Quidway AR 19-1X can accommodate one SIC interface modules and one VPM module at most. The configurations of cables are directly related to the interface modules. The relationship is described in details later. The Quidway AR 19-1X Series is a standard configuration. In product configuration, only cables with standard lengths need to be provided. There is no need for a field survey when selling through agents. However, a field survey is required when selling together with other products of the company. In this case, the requirements raised cannot be met through the configuration of the Quidway AR 19-1X series, but through the configuration of other products. The input range of the AC power supply for the Quidway AR 19-1X series is 100V AC to 240V AV, 50Hz to 60Hz. Therefore, the product can also be used in places where the 110V AC power supply is used.



The accessories delivered are subject to the host. The normal delivery and configuration are not necessary to consider the accessory. If the host is confirmed, the corresponding accessories are attached (including the documents and the CDs). The intention of the list in this version is to make all the interface modules and hosts the ATO items (AI) separately packed. The interface modules and the hosts will be delivered completely separated, similar to the sales of computer accessories. The purpose is mainly to accommodate the distribution of mid-to-low range routers to simplify production testing and debugging, improving market response speed.

1.8 Overall Configuration Description of the Quidway AR 19-1X Series

Overall configuration description: 1. For the configuration of hosts and modules, the lists prepared by the marketing and configuration personnel only need to reach the level of hosts and modules, and they don’t need to care about the stuff below the level of hosts (main boards) and modules. The reason is that the contents of each kind of host (main board) and module are fixed and are ATO items. The code of a host (main board) or a module can contain all the contents inside. 2. For optional cables, the configuration can go down further in detail. Refer to the description of cable configuration in the text below. 3. The Quidway AR 19-1X series is configurable, and the host is powered by the AC power supply. The input voltage range for the host is AC 100V-240V/50-60Hz, so the product can be used in countries or regions where the grid voltage is 110V. 4. The code and description of the AC power supply for the Quidway AR 19-1X series are as below: 0213A00C item description: Primary Power Supply-10degC-55degC-90Vac-264Vac-12V/2.2A 5. In distribution model, the quantity of the interface modules is determined based on the requirements of users, and no longer specifically corresponds to the host. However, for the internal bundled sales within the company, the corresponding relationship between the host and the modules still needs to be considered. For the Quidway AR 19-1X series, the quantity of the optional interface modules is only one. The interface modules usually need to have corresponding cables (they can also do without cables depending on the requirements of the users). For details on configuration of specific interface modules, refer to the section on the module configuration. 6. When in configuration, the choice needs to be made by considering two sales models, that is, distribution and tie-in sales. 7. AUX cables are not included in the list. Special delivery can be arranged if they are specifically needed. 8. The host of the Quidway AR 19-1X has a USB port, and can accommodate a USB flash memory. The USB flash memory is put directly under code 0105, and the users can select USB flash memories with different capacities according to their needs. 9. The accessories delivered are subject to the host. The normal delivery and configuration are not necessary to consider the accessory. If the host is confirmed, the corresponding accessories are attached (including the documents and the CDs). The configuration of the router is explained as follows from four aspects, that is, the host, the modules, the cables, the optical fibers.



2 Host Configuration Description of the Quidway AR 19-1X Series The Quidway AR 19-1X series can only use an AC power supply, and the code and description of the host are as follows:

Table 7 Host code of the Quidway AR 19-1X series

0105A09M item description: Datacom Equipment-Quidway AR 19-1X Series Router-International Version

No. Code Description Quantity Remarks

1 0235A34D Assembly-Quidway AR 19-10-RTVZ31910-Router Host (AC)-International Version


Optional

2 0235A34E Assembly-Quidway AR 19-10-RTVZ31910-Router Host (AC)-WLAN-supported-International Version


Optional

3 0235A34F Assembly-Quidway AR 19-13-RTVZ31913I-Router Host (AC)-International Version


Optional

4 0235A34G Assembly-Quidway AR 19-13-RTVZ31913IW–Router Host (AC)-WALN-supported-International Version


Optional

5 0235A34H Assembly-Quidway AR 19-15-RTVZ31915I-Router Host (AC)-International Version


Optional

6 0235A34J Assembly-Quidway AR 19-15-RTVZ31915IW-Router Host (AC)-WALN-supported-International Version


Optional

To accommodate the distribution model of the product, the host is made into an ATO item with fixed composition, and the inventory can be made directly. Therefore, for configuration and marketing personnel, they can just directly select the host needed under item 0105A09M. Important: the orders for the host of the Quidway AR 19-1X series must be coded and placed in the 0235xxxx category, not the 0105xxxx or 0303xxxx category. Specific configuration description is as follows: 1. The main board of the Quidway AR 19-1X series is fixed inside the chassis, and cannot be delivered separately. The total normative capacity of the memory on the main board is 256 MB. 2. The host of the Quidway AR 19-1X series is an ATO item, and all the items in it must be configured. 3. For orders under the distribution model and the tie-in model, the salespersons first need to select the types of the hosts according to the requirements of the orders or the plans, that is, to select the hosts according to the models of the routers. 4. The input voltage range for the host of the Quidway AR 19-1X series is AC 100V-240V/50-60Hz, so the product can be used in countries or regions where the grid voltage is 110V.



5. To facilitate production and distribution, each kind of host is packed separately and put in the package of the entire machine of the router during delivery. The selected modules are not inserted in the host either, but packed separately. All the expandable slots of the host are installed with false parts to replace the real ones. The selected modules should be installed and tested by the distributors before they are delivered to the end users. If the tie-in sales are performed by the customer service personnel, when deliveries are made to the users directly, the modules will be installed by the distributors or the users themselves. The main idea is to take reference to the sales model of computers and their accessories, in which the separately supplied accessories can be installed by the users. 6. The quantity of the hosts of the Quidway AR 19-1X series is configurable. 7. The power supply of the Quidway AR 19-1X series is put within the chassis and goes with the host, no need to be delivered separately. 8. The accessories delivered are decided by the host. The normal deliver and configuration are not necessary to consider the accessory. If the host is confirmed, the corresponding accessories are attached (including the documents and the CDs). The composition of each type of host is essentially the same, namely, the chassis of the general assembly, the accessories delivered, the complete set of packing materials, the necessary cables, the false parts serving as handlers, as well as the labels. For general configuration and marketing personnel, they only need to reach the host level without going down further.



3 Description of Storage Media Expansion for the Quidway AR 19-1X Series

3.1 Selection of USB Flash Memory

The AR 19-1X router has one USB interface for the external USB flash memory connection. The USB flash memory can be used to store system files, configuration files, as well as log files.



4 Configuration of SIC Interface Module for the Quidway AR 19-1X Series To facilitate production and distribution, all the interface modules of the Quidway AR 19-1X series are made into ATO items. Meantime, all the interface modules include the corresponding packing materials. Normally, they are not directly installed on the host during delivery, but separately packed, shipped together with the host or separately. Generally, the configuration of the interface modules includes two parts: the first is the selection of the interface modules, and the second is the selection of the electric and optical fibers. If selling by distributors, you do not need to consider the corresponding relationship between cables and optical fibers. However, for bundling model and direct delivery to the users, the types and quantities of the single-board electric and optical fibers need to be determined according to the features of the circuits and the number of the interfaces, after selecting corresponding interface modules. In other words, selection needs to be made in the external cable set (04000077) and external optical fibers suite (04100053). Important: the orders for the interface module of the Quidway AR 19-1X series must be coded and placed in the 0231xxxx category, not the 0305xxxx, 0303xxxx, or 0302xxxx category. The interface modules of the Quidway AR 19-1X series mainly include the SIC interface modules and the built-in VPM card modules. The detailed configuration of each interface module is described below.

4.1 Configuration of the RT-SIC-1GEC Interface Module

RT-SIC-1GEC is the SIC module for 1-port 10M/100M/1000M electrical interface and optical Ethernet interface of the Quidway AR 1900/2900/4900 series router, providing one RJ45 electric port and one SFP optical port to the outside. It can work independently in the electrical interface mode or in the optical interface mode. When the two modes exist simultaneously, the electrical interface takes priority. When working in the optical port mode, the SFP optical module needs to be selected and purchased separately. Because only one socket for the SFP optical module is delivered without the optical module along (the optical module is shipped separately). When the electrical interface is used, the module has two operating modes, namely full-duplex and half-duplex, and the full-duplex mode is more commonly used. The configuration list of the RT-SIC-1GEC module is shown in the table below:

Table 8 Configuration list of the RT-SIC-1GEC module

0223A02F item description: Datacom Equipment-QuidwayAR 19/29/49 router-Universal SIC Module

No. Code Description Acronym Remarks 1 0231A07

M Functional module-Quidway AR 49-65-RTVM1S1GEC-SIC module for 1-port 10M/100M/1000M electronic and optical Ethernet ports

RT-SIC-1GEC Optional

Configuration description: 1. The components of the RT-SIC-1GEC module are mandatory. The configuration is quite simple, and you just need to select the code of the module directly. 2. The Quidway AR 19-1X series has one 10/100M Ethernet interface, which needs to be taken into consideration during designing. 3. RT-SIC-1GEC module does not have optical fibers and optical module. If optical port is to be used, you need to configure as follows:



The optical module of RT-SIC-1GEC (pluggable SFP optical module) needs to be selected. The list of currently available optical modules is below.

Table 9 Configuration list of the RT-SIC-1GEC SFP module

0223A02R item description: Assembly/Accessory-Quidway AR 19/29/49 Series Routers-Universal Optical Module

No. Code Description Acronym Remarks 1 02315204

(Corresponding to BOM of H3C: 0231A562)

Datacom Products, DP0M0ESFP, Optical Transceiver, ESFP, GE, Multi-mode Module (850nm, 0.5km, LC)

eSFP-GE-SX-MM850

Configurable

2 02315200 (Corresponding to BOM of H3C: 0231A563)

Datacom Products, DP0M0SFP, Optical Transceiver, SFP, GE, Single-mode Module (1310nm, 10km, LC)

SFP-GE-LX-SM1310

Configurable

3 02315468 (Corresponding to BOM of H3C: 02312173)


FW-SFP-SM(70KM 1550nm LC)

Configurable




Configurable




Configurable

6 02315285 (Corresponding to BOM of H3C: 0231A11U)

Datacom Products, DP0M6SFP, Optical Transceiver, SFP, GE, BIDI Single-mode Module (TX1310/RX1490, 10km, LC)

SFP-GE-LX-SM1310-BIDI

Configurable

7 02315286 (Corresponding to BOM of H3C: 0231A11V)

Datacom Products, DP0M7SFP, Optical Transceiver, SFP, GE, BIDI Single-mode Module (TX1490/RX1310, 10km, LC)

SFP-GE-LX-SM1490-BIDI

Configurable


Datacom Products, DP0M2ESFP, Optical Transceiver, ESFP, GE, Single-mode Module (1550nm, 100km, LC)

eSFP-GE-ZX100-SM1550

Configurable

[Note]: As the receiving and transmitting bands of the two optical modules (02315285 and 02315286) need to match each other, therefore, the two ends of communications need to be used in pairs.

4. The cable and the optical cable used by the 1GEC module can be selected from the external cables set and optical fiber suite. If the 1000M electrical interface is used, one network cable (04027102) needs to be supplied additionally, and the following cables to be selected from the external cables (04000077) are as follows:



04027102 single cable-hub to server straight-through network cable-3.00m-(network interface 8bit-I)-(CC4P0.5 gray)-(network interface 8 bit-I)-C&C08C Each of the interfaces of the 1GEC module has two ports for receiving and transmitting respectively. Therefore, optical fibers must be selected in pairs. In other words, each interface should select two optical fibers. (Only one optical fiber is needed when the BIDI optical module is selected.) The types of connectors (the module side is LC/PC), the length and the modes of the optical modules (single-mode/multi-mode) need to be considered for cables selection. Currently, there are six types of single-mode optical fibers and five types of multi-mode optical fibers available for the 1GEC module. They need to be selected from the optical fiber suite, as shown in the two tables below.

Table 10 Configuration list of the single-mode cables for the RT-SIC-1GEC module

04100053 item description: Optical fiber suite-8040-external cable set

No. Code Description Quantity Remarks 1 14130193 Patch Cord, LC/PC-SC/PC,

Single-mode, 2mm, 5m At customers' option Configurable

Optional

2 14130195 Patch Cord, LC/PC-SC/PC, Single-mode, 2mm, 5m

At customers' option Configurable

Optional



Optional

4 14130287 Patch Cord, LC/PC-SC/PC, Single-mode, 2mm, 2.7m


Optional



Optional



Optional

Table 11 Configuration list of the multi-mode cables for the RT-SIC-1GEC module

04100053 item description: optical fiber suite-8040-external optical fiber suite

No. Code Description Quantity Remarks 1 14130296 Patch Cord, LC/PC-LC/PC,

Multi-mode, 2mm, 5m At customers' option Configurable

Optional

2 14130222 Patch Cord, LC/PC-LC/PC, Multi-mode, 2mm, 10m


Optional



Optional



Optional



Optional

4.2 Configuration of the RT-SIC-4FSW Module and the RT-SIC-9FSW Interface Module

The RT-SIC-4FSW module and the RT-SIC-9FSW module can be used as the 4/9-port 10M/100M Ethernet layer-2 switching interface module of Quidway AR 1900/2900/4900 series routers. The module mainly realizes the layer-2 switching function of the 4/9-line Ethernet, providing up to 4/9 10/100Base-Tx Ethernet ports on the router. This module can be used as



the equipment of switching/routing integration in small-scale intranets, directly connecting the PCs and networking equipment within the organizations. The module can provide 4/9 common RJ45 connectors to the outside. When the user adopts the C5 cable (both crossover and straight-through network cables can be supported), the 100M layer-2 line speed transmission can be reached. Each interface can work in 10M/100M mode, and can be adaptive. Meanwhile, the module has two operating modes, namely, full-duplex and half-duplex, and the full-duplex mode is more commonly used. The configuration list of the RT-SIC-4FSW module and the RT-SIC-9FSW module is shown in the table below:

Table 12 The configuration list of the RT-SIC-4FSW module and the RT-SIC-9FSW

module

0223A02F item description: Assembly/Accessory-QuidwayAR 19/29/49 Series Routers-Universal SIC Module

No. Code Description Acronym Remarks 1 0231A644 Functional module-Quidway AR

49-65-RTVM1S4FSW-4-port 10M/100M Ethernet layer 2 switching module (RJ45)

RT-SIC-4FSW Optional

2 0231A07Y Functional module-Quidway AR 49-65-RTVM1S9FSW-9-port 10M/100M Ethernet layer 2 switching module (RJ45)

RT-DSIC-9FSW Optional

Configuration description: 1. The components of the RT-SIC-4FSW module and the RT-SIC-9FSW module are mandatory. The configuration is simple, and you just need to select the code of the module directly. 2. After the RT-SIC-4FSW module and the RT-SIC-9FSW module are selected, the number of the Ethernet cables should be determined according to the number of the Ethernet interfaces. One network interface must be configured with one network cable (04027102). The following cables to be selected from the external cables set (04000077) are as follows: 04027102 single cable-hub to server straight-through network cable-3.00m-(network interface 8bit-I)-(CC4P0.5 gray)-(network interface 8bit-I)-C&C08C 3. When the SIC slot of the Quidway AR 19-1X series supports the RT-SIC-9FSW module, the guide rail on the right side of slot needs to be disassembled, which needs attention in the installation. 4. The AR 19-1X series router has already come with four 10/100M Ethernet interfaces, which needs to be taken into consideration during designing.

4.3 Configuration of the RT-SIC-1FEA Interface Module

The RT-SIC-1FEA module is the 1-port 10M/100M Ethernet SIC interface module (RJ45) that can be used for the Quidway AR 1900/2900/4900 series routers. Its main function is to realize the access and forward of the Ethernet data at 10M/100M. The configuration list of the RT-SIC-1FEA module is shown in the table below:



Table 13 Configuration list of the RT-SIC-1FEA module

0223A02F item description: Assembly/Accessory-Quidway AR 19/29/49 Series Routers-Universal SIC Interface Module

No. Code Description Acronym Remarks 1 02311371 Quidway R1760,RTHM31FEA,

1-Port 10/100M Ethernet Electrical Interface Board(RJ45)

RT-SIC-1FEA Optional

Configuration description: 1. The components of the RT-SIC-1FEA module are mandatory, and the configuration is quite simple. 2. The AR 19-1X series router has one 10/100M Ethernet interface, which needs to be taken into consideration during designing. 3. The cables for the RT-SIC-1FEA module are required items, and need not be selected from the external cable set.

4.4 Configuration of the RT-SIC-1SAE Interface Module

The RT-SIC-1SAE module is the 1-port enhanced synchronous/asynchronous serial interface module (RJ45) that can be used for the Quidway AR 1900/2900/4900 series routers. Its main function is to complete the transmission and processing of one line of the synchronous/asynchronous serial data streams. This module can support multiple protocols, including V.24, V.35, X.21, RS449, and RS530. The configuration list of the RT-SIC-1SAE module is shown in the table below:

Table 14 Configuration list of the RT-SIC-1SAE module


No. Code Description Acronym Remarks 1 02312550 Quidway R1760,RTHMN1SAE,

1-Port Enhanced Synchronous/Asynchronous Serial Interface Card

RT-SIC-1SAE Optional

Configuration description: 1. No cable for the RT-SIC-1FEA module is required. Select the cable from the external cable set for application if needed. For distribution, you do not need to consider the corresponding relationship of cables. However, for bundling model and direct delivery to the users, the types and quantities of the network cable need to be determined according to the features of the circuits and the number of the interfaces, after selecting the RT-SIC-1SAE module. For example, for each RT-SIC-1SAE module, at most one additional cable should be selected, but the specific type of the cable needs to be decided according to the actual requirements. Currently 10 types of cables can be selected, as shown in the table below, and they need to be selected from the external cable set (04000077). V.35 DCE cable V.35 DTE cable V.24 DCE cable V.24 DTE cable



X.21 DCE cable X.21 DTE cable RS449 DCE cable RS449 DTE cable RS530 DCE cable RS530 DTE cable

Table 15 Configuration List of Optional Cables for the RT-SIC-1SAE Module

04000077 external set-Quidway3680E external cable set

No. Code Description Quantity Remarks 1 04043589 Single Cable, V.24 Serial Port Cable,

3m, D25M, CC(5P+8C)0.32P296U(S), D28M, DTE


Optional

2 04043590 Single cable-V.24 serial cable-3m-(D25 female)-(CC(5P+8C)0.32P547U(S))-(D28 male)-DCE


Optional

3 04043591 Single cable-V.35 serial cable-3m-(D28 male)-(8*CC(5P+8C)0.32P547U(S))-(D34 male+D34 plastic shell)-DTE


Optional

4 04043592 Single cable-V.35 serial cable-3m-(D28 male)-(8*CC(5P+8C)0.32P547U(S))-(D34 female+D34 plastic shell)-DCE


Optional

5 04043593 Single cable-X.21 serial cable-3m-(D15 male)-(CC(5P+8C)0.32P547U(S))-(D28 male)-DTE


Optional

6 04043594 Single cable-X.21 serial cable-3m-(D15 female)-(CC(5P+8C)0.32P547U(S))-(D28 male)-DCE


Optional

7 04043595 Single Cable,RS449 Serial Port Cable, 3m, D28M, 100CC13P0.32P296U(S), D37M-I, DTE


Optional

8 04043596 Single Cable,RS449 Serial Port Cable, 3m, D28M, 100CC13P0.32P296U(S), D37F-I, DCE


Optional

9 04043597 Single cable-RS530 serial cable-3m-(D25 male)-(10CC13P0.32P547U(S))-(D28 male)-DTE


Optional

10 04043770 Single cable-RS530 serial cable-3m-(D25 female)-(10CC13P0.32P547U(S))-(D28 male)-DCE


Optional

The above 10 types of cables are optional, and a correct one must be selected from them when selecting the RT-SIC-1SAE module, or the cables will not be attached.

4.5 Configuration of the RT-SIC-1E1-F Module and the RT-SIC-EPRI Interface Module

The RT-SIC-1E1-F module is the 1-port unchannelized E1 SIC interface module that can be used for the Quidway AR 1900/2900/4900 series routers. Its main function is to transmit and process E1 data streams. It can provide the Fractional E1 access mode. E1-F does not support channelized E1 processing. The RT-SIC-1E1-F module provides one E1 port for access. The RT-SIC-EPRI module is the 1-port E1/CE1/PRI SIC interface module that can be used for the Quidway AR 1900/2900/4900 series routers. Its main function is to transmit and process



E1 data streams. Meanwhile, it can provide CE1 access and the ISDN PRI function, realizing multiple functions on one board. The configuration list of the RT-SIC-1E1-F module and the RT-SIC-EPRI module is shown in the table below:

Table 16 Configuration of the RT-SIC-1E1-F module and the RT-SIC-EPRI module


No. Code Description Acronym Remarks 1 02311804 Quidway R1760,RTHMLE1F,

1-Port E1 & Fractional E1 Interface Module

RT-SIC-1E1-F Optional

2 02311374 Quidway R1760,RTHM6EPRI, 1-Port Interface Card Of E1/CE1/PRI Compatible

RT-SIC-EPRI Optional

Configuration description: 1. The components of the RT-SIC-1E1-F module and the RT-SIC-EPRI module are mandatory. The configuration is quite simple, and you just need to select the code of the module directly. 2. For distribution, you do not need to consider the corresponding relationship of cables. However, for bundling model and direct delivery to the users, the types and quantities of the network cable need to be determined according to the features of the circuits and the number of the interfaces, after selecting the RT-SIC-1E1-F module and the RT-SIC-EPRI module. The cable configuration of the RT-SIC-1E1-F module and the RT-SIC-EPRI module are shown in the table below. Seven kinds of cables and two kinds of connectors are available in total. All the seven types of cables are optional (among them, cables with the code of 04026105 are mainly used in self-looped testing, and are rarely used in routine delivery activities). Before configuring the cables for the RT-SIC-1E1-F module and the RT-SIC-EPRI modules, you need to check out the features of the E1 line first. The cable connecting with the RT-SIC-1E1-F module is the E1 G.703 cable, which has two types available for selection, and both types use the DB-15 connector at the interface end of the module, but at the network end, the connectors are respectively:

BNC connector, corresponding to the 75Ω non-balanced coaxial cables (codes: 04026106, 04040148, and 04040149)

RJ45 crystal connector, corresponding to 120Ω balanced unshielded twisted pair cables (codes: 04026104, 04040150, and 04040151)

Table 17 Cable Configuration of the RT-SIC-1E1-F module and the RT-SIC-EPRI

module


No. Code Description Acronym Remarks 1 04026104 Trunk Cable, G.703 Cable, 3.00m, 120ohm,

1E1, 0.4mm, D15M+Magnetic Ring 17010171, 120CC2P0.4P430U(S), MP8-II, W4157


Optional

2 04026105 Trunk Cable, G.703 Cable, 3.00m, 120ohm, 1E1, 0.4mm, D15M+Magnetic Ring 17010171, 120CC2P0.4P430U(S), MP8-II, W4157


Optional

3 04026106 Trunk Cable, 3.00m, 75ohm, 1E1-2.2mm, D15M+Magnetic Ring 17010171, 2*SYFVZ75-1.2/0.25, 2*BNC75SM-V, Quidway 2500, W4159


Optional



No. Code Description Acronym Remarks 4 04040148 Trunk Cable, 20.00m, 75ohm, 1E1, 2.2mm,

D15M+Magnetic Ring17010171, 2*SYFVZ75-1.2/0.25, 2*BNC75SM-V


Optional

5 04040149 Trunk Cable, 40.00m, 75ohm, 1E1, 2.2mm, D15M+Magnetic Ring17010171, 2*SYFVZ75-1.2/0.25, 2*BNC75SM-V


Optional

6 14040202 Coaxial Connector, BNC, 75ohm, Straight/Socket, Dual, Female, Connected With E1 Cable BNC Male Plug


Optional

7 04040150 Trunk Cable, G.703 Cable, 20.00m, 120ohm, 1E1, 0.4mm, D15M+Magnetic Ring17010171, 120CC2P0.4P430U(S), MP8-II


Optional



Optional

9 14080099 Network interface connector-8-bit/8PIN-unshielded-convertion socket-NO keyed


Optional

10 04026813 Single Cable, 120ohm-75ohm Converter Box (With BNC Socket 14040083), 2*BNC75SF, 26UL2464(4C)B+PCB03022938)


Optional

When cables with BNC connectors (codes are 04026106, 04040148, and 04040149) are selected, you still need to select two coaxial connectors (14040202) for each E1 interface based on the 1:2 ratio in accordance with the number of the cables. This is to facilitate the users or the customer service personnel to extend the length of the cables. When cables with the RJ45 crystal connectors (codes are 04026104, 04040150, and 04040151) are selected, you still need to select one more RJ45 connector (14080099) for each E1 interface based on the 1:1 ratio in accordance with the number of the cables. The above two categories of cables are optional, and need to be purchased separately. The choice must be made when configuring the E1 module. Because RT-SIC-1E1-F and RT-SIC-EPRI provide one E1 port respectively, each module needs to select one cable (or one pair of cables). 04026813 is used for conversion between 120Ω and 75Ω resistance for the E1 cables. You can select it if needed. Generally, our interface modules already support both 120Ω and 75Ω resistance, so you are not recommended to use resistance conversion for the circuit matching. 3. RT-SIC-1E1-F and RT-SIC-EPR have an 8-bit DIP switch within them. By default, all the 8 bits are ON, indicating the 75Ω unbalanced coaxial cable (such as 04026106) is selected. To select the 120Ω balanced and unshielded twisted pair (such as 04026104), the DIP switch should be switched to OFF. For details, refer to Installation Manual of Quidway AR 1900 Series Routers.

4.6 Configuration of the RT-SIC-1FXS-V2 and RT-SIC-2FXS-V2 Interface Module

RT-SIC-1FXS-V2 and RT-SIC-2FXS-V2 modules are the SIC interface modules for the 1/2-port voice module subscriber circuit, which can be used for the Quidway AR 1900/2900/4900 series routers. Their main function is to access and process the analog voice signals of 1/2-lines, realizing the transmission of voice signals on the data communication networks. RT-SIC-1FXS-V2 and RT-SIC-2FXS-V2 realize the analog user interface of 1/2-ports respectively, and can directly drive 1/2 common analog telephone sets.



The configuration list of the RT-SIC-1FXS-V2 module and the RT-SIC-2FXS-V2 module is shown in the table below:

Table 18 Configuration list of RT-SIC-1FXS-V2 and RT-SIC-2FXS-V2


No. Code Description Acronym Remarks 1 0231A08Q Functional

module-QuidwayAR28-09-RTHM31FXS-1-port voice module user circuit interface board

RT-SIC-1FXS-V2 Optional

2 0231A08P Functional module-QuidwayAR28-09-RTHM32FXS-2-port voice module user circuit interface board

RT-SIC-2FXS-V2 Optional

Configuration description: 1. The components of the RT-SIC-1FXS-V2 module and the RT-SIC-2FXS-V2 module are mandatory. The configuration is simple, and you just need to select the code of the module directly. 2. The cable for the RT-SIC-1FXS-V2 module and the RT-SIC-2FXS-V2 module are required items, and need not be selected from the external cable set.

4.7 Configuration of the RT-SIC-1FXO-V2 Module and the RT-SIC-2FXO-V2 Module

RT-SIC-1FXO-V2 and RT-SIC-2FXO-V2 modules are the SIC interface modules for 1/2-ports voice module ATO relay circuit that can be used for the Quidway AR 1900/2900/4900 series routers. Their main function is to receive and process 1/2-lines of the analog voice signals, realizing the voice signal transmission on the data communication networks. The RT-SIC-1FXO-V2 module and the RT-SIC-2FXO-V2 module realize the relay interfaces of the 1/2-ports ATO circuits respectively, and can realize the access of 1/2-line analog users, such as the connection of external telephone lines. The configuration list of The RT-SIC-1FXO-V2 module and the RT-SIC-2FXO-V2 module is shown in the table below.

Table 19 Configuration list of RT-SIC-1FXO-V2 and RT-SIC-2FXO-V2


No. Code Description Acronym Remarks 1 0231A07S Functional

module-QuidwayAR28-09-RTHM32FXO-1-port voice module ATO relay circuit interface module

RT-SIC-1FXO-V2 Optional

2 0231A07R Functional module-QuidwayAR28-09-RTHM32FXO-2-port voice module ATO relay circuit interface module

RT-SIC-2FXO-V2 Optional

Configuration description: 1. The components of the RT-SIC-1FXO-V2 module and the RT-SIC-2FXO-V2 module are mandatory. The configuration is simple, and you just need to select the code of the module directly.



2. The cable for the RT-SIC-1FXO-V2 module and the RT-SIC-2FXO-V2 module are required items, and need not be selected from the external cable set.

4.8 Configuration of the RT-SIC-1ADSL-I Interface Module

The RT-SIC-1ADSL-I module is the 1-port ADSL over ISDN SIC interface module that can be used for the Quidway AR 1900/2900/4900 series routers. Its main function is to connect directly to DSLAM through the user’s line and to provide broadband access to the users. RT-SIC-1ADSL-I provides one ADSL (over ISDN) port and connects one telephone line. The configuration list of the RT-SIC-1ADSL-I module is shown in the table below.

Table 20 Configuration list of the RT-SIC-1ADSL-I module


No. Code Description Acronym Remarks 1 0231A08M Functional

module-QuidwayAR28-09-RTHM11ADI-1-port ADSL over ISDN interface card

RT-SIC-1ADSL-I Optional

Configuration description: 1. The components of the RT-SIC-1ADSL-Imodule are mandatory. The configuration is quite simple, and you just need to select the code of the module directly. 2. Cables for the RT-SIC-1ADSL-I module are required items and need not be selected from the external cable set. 3. When the user adopts broadband network access through ADSL, the ISDN function can also be used on the same subscriber line with a splitter, which has already been included in the package and does not need to be supplied separately. 4. Quidway AR 19-15-I and Quidway AR 19-15-IW routers have integrated one port, namely, ADSL2+ over POTS, which needs to be considered in the solution design.

4.9 Configuration of the RT-SIC-1ADSL Interface Module

The RT-SIC-1ADSL module is the 1-port ADSL over POTS SIC interface module that can be used for the Quidway AR 1900/2900/4900 series routers. Its main function is to connect directly to DSLAM through the subscriber line and to provide broadband access for the users. RT-SIC-1ADSL provides one ADSL (over POTS) port and connects one telephone line. The configuration list of the RT-SIC-1ADSL module is shown in the table below.

Table 21 Configuration list of the RT-SIC-1ADSL module


No. Code Description Acronym Remarks 1 0231A08N Functional module-Quidway

AR28-09-RTHM11ADP-1-port ADSL over POTS interface card

RT-SIC-1ADSL Optional

Configuration description: 1. The components of the RT-SIC-1ADSL module are mandatory. The configuration is quite simple, and you just need to select the code of the module directly.



2. Quidway AR 19-15-I and AR 19-15-IW routers have integrated one port, namely, ADSL2+ over POTS, which needs to be considered in the solution design. 3. Cables for the RT-SIC-1ADSL-I module are required items and need not be selected from the external cable set. 4. When the user adopts broadband network access through ADSL, the ISDN function can also be used on the same subscriber line by one splitter, we have prepared a separate list of optional parts including one type of splitter, which can be used by the users if needed. As shown in Table 27 , currently only one type of splitter is available. The splitter is optional and not required. It can be selected based on the actual application environment of the users. Generally, one ADSL port is provided with one splitter.

Table 22 List of the Optional Accessories for the RT-SIC-1ADSL

No. Code Description Quantity Remarks 1 02231674 DEMUX, ADSL Full Rate

Demultiplexer, Low Pass Filter At customers' option

Optional

4.10 Configuration of the RT-SIC-1AM-V3 Interface Module

The RT-SIC-1AM-V3 module is the SIC interface module for the 1-port analog modem that can be used for the Quidway AR 1900/2900/4900 series routers. Its main function is to perform the receiving and processing tasks for the 1-line analog modem calls and connect one external telephone line. The configuration list of the RT-SIC-1AM-V3 module is shown in the table below.

Table 23 Configuration list of the RT-SIC-1AM-V3 module


No. Code Description Acronym Remarks 1 0231A39P Functional module-Quidway AR

28-09-RTHM31AM-1-port analog modem interface module

RT-SIC-1AM-V3 Optional

Configuration description: 1. The components of the RT-SIC-1AM-V3 module are mandatory. The configuration is quite simple, and you just need to select the code of the module directly. 2. Cables for the RT-SIC-1AM-V3 module are required items and need not be selected from the external cable set.

4.11 Configuration of the RT-SIC-1VE1 Interface Module

The RT-SIC-1VE1 module is the 1-line E1 voice SIC interface module available for the Quidway AR 1900/2900/4900 series router, functioning for successful processing and transmission of the 30-line voice, data, and facsimile signal on the data communication network. The RT-SIC-1VE1 module provides one E1 port and realizes 1-line E1 voice relay access. The configuration list of the R T-SIC-1VE1 module is shown in the table below.



Table 24 Configuration list of the R T-SIC-1VE1 module


No. Code Description Acronym Remarks 1 0231A13S Functional module-Quidway AR

49-65-RTVM1S1VE1-1VT1-SIC module

RT-SIC-1VE1 Optional

Configuration description: 1. The RT-SIC-1VE1 must be used together with one insertion piece, VPM32, VPM16, VPM8, or VPM24. 2. Quidway AR 19-10, Quidway AR 19-10 W, Quidway AR 19-1 and Quidway AR 19-15-I do not support the RT-SIC-1VE1 module. 3. The components of the RT-SIC-1VE1 module are mandatory. The configuration is quite simple, and you just need to select the code of the module directly. 4. For distribution, you do not need to consider the corresponding relationship of cables. However, for bundling model and direct delivery to users, the type of the cable need to be determined according to the features of the circuits, after selecting the RT-SIC-1VE1 module. The cable connecting with the RT-SIC-1VE1 module is the E1 G.703 cable, which has two types available for selection, and both types use the DB-15 connector at the interface end of the module, but at the network end, the connectors used are respectively:

BNC connector, corresponding to the 75Ω non-balanced coaxial cables (codes: 04026106, 04040148, and 04040149)

RJ45 crystal connector, corresponding to 120Ω balanced unshielded twisted pair cables (codes: 04026104, 04040150, and 04040151)

The cable configuration of the RT-SIC-1VE1 module is shown in the table below. Seven kinds of cables and two kinds of connectors are available in total. All the seven types of cables are optional (among them, cables with the code of 04026105 are mainly used in self-looped testing, and are rarely used in routine delivery activities).

Table 25 Cable configuration list of the R T-SIC-1VE1 module


No. Code Description Quantity Remarks 1 04026104 Trunk Cable, G.703 Cable, 3.00m,

120ohm, 1E1, 0.4mm, D15M+Magnetic Ring 17010171, 120CC2P0.4P430U(S), MP8-II, W4157


Optional

2 04026105 Trunk Cable, 3.00m, 120ohm, 1E1, 0.4mm, D15M+Magnetic Ring 17010171, 120CC2P0.4P430U(S), MP8-II, G.703/NT Cable


Optional



Optional



Optional



No. Code Description Quantity Remarks 5 04040149 Trunk Cable, 40.00m, 75ohm, 1E1,

2.2mm, D15M+Magnetic Ring17010171, 2*SYFVZ75-1.2/0.25, 2*BNC75SM-V


Optional



Optional



Optional



Optional



Optional

10 04026813 Single Cable, 120ohm-75ohm Converter Box (With BNC Socket 14040083), 2*BNC75SF, 26UL2464(4C)B+PCB03022938)


Optional

When cables with BNC connectors (codes are 04026106, 04040148, and 04040149) are selected, you still need to select two coaxial connectors (14040202) for each RT-SIC-1VE1 interface based on the 1:2 ratio in accordance with the number of the cables. This is to facilitate the users or the customer service personnel to extend the length of the cables. When cables with the RJ45 crystal connectors (codes are 04026104, 04040150, and 04040151) are selected, you still need to select one more RJ45 connector (14080099) for each RT-SIC-1VE1 interface based on the 1:1 ratio in accordance with the number of the cables. This is to facilitate the users or the customer service personnel to extend the length of the cables. The above two categories of cables are optional, and need to be purchased separately. The choice must be made when configuring the RT-SIC-1VE1 module. Because the RT-SIC-1VE1 module provides one E1 port, each module needs to select one cable. 04026813 is used for conversion between 120Ω and 75Ω resistance for the RT-SIC-1VE1 cables. You can select it if needed. Generally, our interface modules already support both 120Ω and 75Ω resistance, so you are not recommended to use resistance conversion for the circuit matching. 5. The RT-SIC-1VE1 module has an 8-bit DIP switch. By default, all the 8 bits are ON, indicating the 75Ω unbalanced coaxial cable (such as 04026106) is selected. To select the 120Ω balanced unshielded twisted pair (such as 04026104), the DIP switch should be switched to OFF.

4.12 Configuration of the RT-SIC-1BS-V2 Interface Module

The RT-SIC-1E1-F module is the short form of the 1-port ISDN BRI S/T interface card available for the Quidway AR 1900/2900/4900 series routers, mainly functioning for successful receiving/transmitting and processing of 1-line ISDN BRI S/T data streams. It has the dial-up mode and the dedicated line mode. The configuration list of the RT-SIC-1BS-V2 module is shown in the table below.



Table 26 Configuration list of the RT-SIC-1BS-V2 module


No. Code Description Acronym Remarks 1 0231A30W Functional module-Quidway

AR 49-65-RTVM1S1BS-1-port ISDN basic rate S/T interface SIC module

RT-SIC-1BS-V2 Optional

Configuration description: 1. The components of the RT-SIC-1BS-V2 module are mandatory. The configuration is quite simple, and you just need to select the code of the module directly. 2. Cables for the RT-SIC-1BS-V2 module are required items and need not be selected from the external cable set.

4.13 Configuration of the RT-SIC-1BU-V2 Interface Module

The RT-SIC-1BU-V2 module is the short form of the 1-port ISDN BRI U interface card available for the Quidway AR 1900/2900/4900 series routers, mainly functioning for successful receiving/transmitting and processing of 1-line ISDN BRI U data streams. It has the dial-up mode and the dedicated line mode. The configuration list of the RT-SIC-1BU-V2 module is shown in the table below.

Table 27 Configuration list of the RT-SIC-1BU-V2 module


No. Code Description Acronym Remarks 1 0231A30Y Functional module-Quidway AR

49-65-RTVM1S1BU-1-port ISDN basic rate U interface SIC module

RT-SIC-1BS-V2 Optional

Configuration description: 1. The components of the RT-SIC-1BU-V2 module are mandatory. The configuration is quite simple, and you just need to select the code of the module directly. 2. Cables for the RT-SIC-1BU-V2 module are required items and need not be selected from the external cable set.

4.14 Configuration of the RT-SIC-1BSV Module and the RT-SIC-2BSV Module

The RT-SIC-1BSV module and the RT-SIC-2BSV module are the short form of 1/2-port ISDN BRI S/T interface voice modules available for the Quidway AR 1900/2900/4900 series routers. The board mainly functions for access, compression and decompression of the ISDN interface voice signal. The interface meets the ITU-T I.430 standard. The transmission code pattern is pseudo-ternary code, the interface rate is 192Kbit/s and the maximum distance is 1 km in end-to-end method. The upstream connects to the user interface of the ISDN switch, realizing the sending/receiving and compression/decompression for ISDN BRI interface digital voice stream. The upstream connects to TE equipment, so the voice packet is sent to the Internet through other WLAN interface, realizing the VoIP function.



The configuration list of the RT-SIC-1BSV module and the RT-SIC-2BSV module is shown in the table below.

Table 28 Configuration list of RT-SIC-1BSV and RT-SIC-2BSV



49-65-RTVM2S1BSV-1-port ISDN basic rate S/T voice interface SIC module




Configuration description: 1. The components of the RT-SIC-1BSV module and the RT-SIC-2BSV module are mandatory. The configuration is simple, and you just need to select the code of the module directly. 2. Cables for the RT-SIC-1BSV module and the RT-SIC-2BSV module are required items and need not be selected from the external cable set.

4.15 Configuration of the RT-SIC-1FEF Interface Module

RT-SIC-1FEF is the short form of 1-port 100M Ethernet optical interface card. FE is the acronym of fast Ethernet. F stands for fiber, meaning the (fiber) optical interface. SIC-1FEF mainly functions for successful communication between the router and the LAN. SIC-1FEF supports the following functions: Five types of SFP pluggable optical interface modules:

Multi-mode short haul FE (850nm) Signal-mode medium haul FE (1310nm) Single-mode long haul FE (1310nm) Single-mode long haul FE (1550nm) Single-mode ultra-long haul FE (1550nm)

Users can select the types according to their needs. The rate of interface transmission is below 100 Mbps. Full duplex is supported. The configuration list of the RT-SIC-1FEF module is shown in the table below:

Table 29 Configuration list of the RT-SIC-1FEF module



49-65-RTVM2S1FEF-1-port 100M SFP SIC module

RT-SIC-1FEF Optional

Configuration description: 1. The components of the RT-SIC-1FEF module are mandatory. The configuration is quite simple, and you just need to select the code of the module directly.



2. The Quidway AR 19-1X series has one 10/100M Ethernet interface, which needs to be taken into consideration in solution design. 3. The RT-SIC-1FEF module does not have optical fibers and optical module, you need to configure as below. A list of the currently available optical modules is shown in the table below.

Table 30 Configuration list of the RT-SIC-1FEF SFP optical module

0223A02R item description: Assembly/Accessory-Quidway AR 19/29/49 Series Routers-Universal Optical Module

No. Code Description Acronym

Quantity Remarks


Datacom Products, DP0M5SFP, Optical Transceiver, SFP, 100M/155M, Multi-mode Module (1310nm, 2km, LC)

SFP-FE-SX-MM1310


Optional


Datacom Products, DP0M1ESFP, Optical Transceiver, ESFP, 100M/155M, Single-mode Module (1310nm, 15km, LC)

eSFP-FE-LX-SM1310


Optional


Datacom Products, DP0M1SFP, Optical Transceiver, SFP, 100M/155M, Single-mode Module (1310nm, 40km, LC)

SFP-FE-LH40-SM1310


Optional


Datacom Products, DP0M4SFP, Optical Transceiver, SFP, 100M/155M, Single-mode Module (1550nm, 80km, LC)

SFP-FE-LH80-SM1550


Optional

5 02315203 (Corresponding to BOM of H3C: 0231A12T)

Datacom Products, DP0M3SFP, Optical Transceiver, SFP, FE, BIDI Single-mode Module (TX1310/RX1550, 15km, LC)

SFP-FE-LX-SM1310-BIDI


Optional

6 02315202 (Corresponding to BOM of H3C: 0231A12U)

Datacom Products, DP0M2SFP, Optical Transceiver, SFP, FE, BIDI Single-mode Module (TX1550/RX1310, 15km, LC)

SFP-FE-LX-SM1550-BIDI


Optional

[Note]: As the receiving and transmitting bands of the two optical modules (02315285 and 02315286) need to match each other, therefore, the two ends of communications need to be used in pairs.

4. The optical cable used by the 1FEF module need be selected from the external optical fiber suite. Each of the interfaces of the 1FEF module has two ports for receiving and transmitting respectively. Therefore, optical fibers must be selected in pairs. In other words, each interface should select two optical fibers. The types of connectors (the module side is LC), the length and the modes of the optical modules (single-mode/multi-mode) need to be considered for cables selection. Currently, there are six types of single-mode optical fibers and five types of multi-mode optical fibers available for the 1FEF module. They need be selected from the optical fiber suite, as shown in the two tables below.



Table 31 Configuration list of the single-mode cables for the RT-SIC-1FEF module

04100053 project description: Optical fiber suite-8040-external cable set

No. Code Description Quantity Remarks 1 14130193 Patch Cord, LC/PC-SC/PC,

Single-mode, 2mm, 5m At customers' option

Optional

2 14130195 Patch Cord, LC/PC-LC/PC, Single-mode, 2mm, 5m


Optional



Optional

4 14130287 Patch Cord, LC/PC-SC/PC, Single-mode, 2mm, 2.7m


Optional



Optional

6 14130280 Patch Cord, LC/PC, SC/PC, Single-mode, 2mm, 20m


Optional

Table 32 Configuration list of the multi-mode cables for the RT-SIC-1FEF module


No. Code Description Quantity Remarks 1 14130296 Patch Cord, LC/PC-LC/PC,

Multi-mode, 2mm, 5m At customers' option

Optional



Optional

3 14130223 Patch Cord, LC/PC-SC/PC, Multi-mode, 2mm, 10m


Optional

4 14130279 Patch Cord, LC/PC, SC/PC, Multi-mode, 2mm, 20m


Optional



Optional

4.16 Configuration of the RT-SIC-2FXS1FXO Interface Module

The RT-SIC-2FXS1FXO module is the SIC interface module for the 2-port voice module subscriber circuit and 1-port voice module ATO relay circuit available for the Quidway AR 1900/2900/4900 series router. The main function is to complete the access and processing of the 1-line and 2-line analog voice signal, realizing the transmission of the voice signal on the data communication network. The RT-SIC-2FXS1FXO module realizes the 2-port analog user interface, that is, two regular telephones and 1-port ATO loop relay interface can be used. It also realizes the access of 1-line analog subscriber line, like external telephone connection. The configuration list of the RT-SIC-2FXS1FXO module is shown in the table below:

Table 33 Configuration list of the RT-SIC-2FXS1FXO module



49-65-RTVM2S2S1O-2FXS+1FXO voice SIC module

RT-SIC-2FXS1FXO Optional

Configuration description: 1. The components of the RT-SIC-2FXS1FXO module are mandatory. The configuration is quite simple, and you just need to select the code of the module directly. 2. The cables for the RT-SIC-2FXS1FXO module are required items, and need not be selected from the external cable set.



5 Configuration Description for External Cable Set of the Quidway AR 19-1X Series The Quidway AR 19-1X router can use the external cable set of the Quidway 3680E router in the 8040 family. The configuration of the external cable set is directly related to the interface modules. For detailed configuration methods, refer to the section of the interface module configuration below. In the external cable set for the Quidway AR 19-1X series, all the cables are optional. Other required cables for routers have already been put under the codes of the corresponding hosts or modules as the mandatory items, such as the cables for the console port, the grounding cables, as well as the required cables for other modules. The configuration of the external cable set is directly related to the interface modules. For detailed configuration methods, refer to the module configuration section. Configuration list for external cable set of the Quidway AR 19-1X series is below.

Table 34 Configuration list for external cable set of the Quidway AR 19-1X series


No. Code Description Quantity Remarks 1 04021135 Single Cable, V.24 Serial Port Cable,

DTE-3.00m, D25M, CC7P0.32P296U(S), D50M-I, QuidWay2501, W2066


Optional

2 04021136 Single Cable, V.24 Serial Port Cable, DCE, 3m, D25F, CC7P0.32P296U(S), D50M-I, W2067


Optional

3 04021137 Single Cable, V.35 Serial Port Cable, DTE, 3m, D34M+D34(PS), CC(5P+8C)0.32P296U(S), D50M-I, QuidWay2501, W2068


Optional

4 04021138 Single Cable, V.35 Serial Port Cable, DCE, 3m, D34F+D34(PS), CC(5P+8C)0.32P296U(S), D50M-I, QuidWay2501, W2069


Optional

5 04021299 Single Cable, Auxiliary Port Cable, 3m, D25M, 2*CC4P0.32P296U(S), DB9M+MP8-VI, QuidwayR2501, W2215


Optional

6 04021300 Single Cable, Configuration Cable, 3m, D25F, 2*CC4P0.32P296U(S), DB9F+MP8-VI, QuidwayR2501, W2216


Optional

7 04026104 Trunk Cable, G.703 Cable, 3.00m, 120ohm, 1E1, 0.4mm, D15M+Magnetic Ring 17010171, 120CC2P0.4P430U(S), MP8-II, W4157


Optional

8 04026105 Trunk Cable, 3.00m, 120ohm, 1E1, 0.4mm, D15M+Magnetic Ring 17010171, 120CC2P0.4P430U(S), MP8-II, G.703/NT Cable


Optional



Optional

10 04026107 Single Cable, PPP Protocol Cable, 1.83m, D68M, 16*CC8C0.32P296U(S), 8*D25M+8*D9M)


Optional



No. Code Description Quantity Remarks 11 04026813 Single Cable, 120ohm-75ohm Converter

Box (With BNC Socket 14040083), 2*BNC75SF, 26UL2464(4C)B+PCB03022938)


Optional

12 04027102 Single Cable, Straight Through Cable, 3.00m, MP8-I, CC4P0.5GY, MP8-I, Unshielded


Optional

13 04040007 Trunk Cable, 0.30m, 120ohm, 4E1, 0.4mm, D25M, 4*120CC4P0.4P430U(S), 4*D15F


Optional

14 04040045 Single Cable, Transit Cable, 0.3m, D100M, 4*100CC13P0.32P547U(S), 4*D50F-II, Quidway3680


Optional

15 04040117 Trunk Cable, For Transit, 3m, 75ohm, 8E1, 2.2mm, D68M-III, 2*SYFVZ75-1.2/0.25*8, 16*BNC75SM-V


Optional



Optional



Optional



Optional



Optional

20 04040201 Single Cable, USB Serial Port Cable, 1.835m, USBA, CC(1P0.32+2C0.5)PWG1U(S), USBB, Quidway


Optional

21 04040285 Single Cable, Communication Cable, 3m, D200M, 32*CC8C0.32P296U(S), 16*D25M+16*D9M, 16AS


Optional

22 04040286 Single Cable, V.35 Serial Port Cable, 3m, D200M, 8*CC(5P+8C)0.32P296U(S), 8*D34M+8*D34(PS), DTE


Optional

23 04040287 Single Cable, V.35 Serial Port Cable, 3m, D200M, 8*CC(5P+8C)0.32P296U(S), 8*D34M+8*D34(PS), DCE


Optional

24 04040288 Single Cable, V.24 Serial Port Cable, 3m, D200M, 8*CC7P0.32P296U(S), 8*D25M


Optional

25 04040289 Single Cable, V.24 Serial Port Cable, 3m, D200M, 8*CC7P0.32P296U(S), 8*D25F, Quidway R3680


Optional

26 04040418 Trunk Cable, Transit Cable, 3m, 120ohm, 8E1/8T1, 0.4mm, D68M, 8*120CC2P0.4P430U(S), 8*MP8-II


Optional

27 04040671 Single cable-–48V feeder cable-2.2m-(D3 female-2 females 1 male)-(14UL2517(2C)PWG1U)-(2*cord end 2.5^2 blue)-MA5103


Optional

28 04041054 Single Cable, Shielding Straight Through Cable, 3.00m, MP8-IV, CC4P0.5P445U(S), MP8-IV


Optional



No. Code Description Quantity Remarks 29 04041104 China Power Cable 250V10A 3m,

I-Type3PIN Straight Plug /227IEC53(RVV)3x1mm^2Black/3PIN Straight Connector


Optional

30 04041152 Trunk cable-transfer cable-0.30m-75ohm-4E1-2.6mm-(D25 male)-(SYYV75-2/0.34(S))-(4*D15 female)


Optional

31 04041153 Single Cable, 8AS Cable (Mate RJ45 Jack), 0.5m, D68M, 8*CC8C0.32P296U(S), 8*MP8-III, 8040


Optional

32 04041307 External Power Cable, Chassis PGND, 3m, 3.3mm^2-G&Y, OT6-4, 12UL1015G&Y, Quidway


Optional

33 04041458 Single Cable, 16AS Communication Cable, 0.5m, D200M, 16*CC8C0.32P296U(S), 16*MP8(S)-III,


Optional

34 04041691 Single Cable, Communication Cable, 0.5m, D68M, 8*CC8C0.32P296U(S), 8*MP8-III, 8AS


Optional

35 04041692 Single Cable, Communication Cable, 0.5m, D200M, 16*CC8C0.32P296U(S), 16*MP8-III, 16AS


Optional

36 04042020 Single Cable, T1 Communication Cable (Matching RJ45), 3m, D15M, CC4P0.5P445U(S), MP8-II, 8040


Optional

37 04042967 Single Cable, Console Serial Port Cable, 3m, D9F, CC4P0.48B(S), MP8-VI


Optional

38 04042968 Single Cable,X.21 Serial Port Cable, 3m, D15M, CC7P0.32P296U(S), D50M-I, DTE


Optional

39 04042969 Single Cable,X.21 Serial Port Cable, 3m, D15F, CC7P0.32P296U(S), D50M-I, DCE


Optional

40 04042970 Single Cable,RS449 Serial Port Cable, 3m, D37F, 100CC13P0.32P296U(S), D50M-I, DCE


Optional

41 04042971 Single Cable,RS449 Serial Port Cable, 3m, D37M-I, 100CC13P0.32P296U(S), D50M-I, DTE


Optional

42 04042972 Single Cable,RS530 Serial Port Cable, 3m, D25M, 100CC13P0.32P296U(S), D50M-I, DTE


Optional

43 04043589 Single Cable, V.24 Serial Port Cable, 3m, D25M, CC(5P+8C)0.32P296U(S), D28M, DTE


Optional

44 04043590 Single Cable, V.24 Serial Port Cable, 3m, D25F, CC(5P+8C)0.32P296U(S), D28M, DCE


Optional

45 04043591 Single Cable, V.35 Serial Port Cable, 3m, D28M, CC(5P+8C)0.32P296U(S), D34M+D34PS, DTE


Optional

46 04043592 Single Cable, V.35 Serial Port Cable, 3m, D28M, CC(5P+8C)0.32P296U(S), D34F+D34PS, DCE


Optional

47 04043593 Single Cable,X.21 Serial Port Cable, 3m, D15M, CC(5P+8C)0.32P296U(S), D28M, DTE


Optional

48 04043594 Single Cable,X.21 Serial Port Cable, 3m, D15F, CC(5P+8C)0.32P296U(S), D28M, DCE


Optional



No. Code Description Quantity Remarks 49 04043595 Single Cable,RS449 Serial Port Cable,

3m, D28M, 100CC13P0.32P296U(S), D37M-I, DTE


Optional

50 04043596 Single Cable,RS449 Serial Port Cable, 3m, D28M, 100CC13P0.32P296U(S), D37F-I, DCE


Optional

51 04043597 Single Cable,RS530 Serial Port Cable, 3m, D25M, 100CC13P0.32P296U(S), D28M, DTE


Optional

50 04043770 Single Cable,RS530 Serial Port Cable, 3m, D25F, 100CC13P0.32P296U(S), D28M, DCE


Optional

51 0404A00Q

Trunk cable-swither-3.0m-75ohm-8E1-1.2mm-(D68 male-III)-(2*SYFVZP75-1.2/0.25*8(S))-(16*BNC75 straight male-V)-IMA


Optional

52 0404A00R

Trunk cable-swither-3.0m-120ohm-8E1-0.4mm-(D68 male)-(8*120CC2P0.4P430U(S))-(8*network port 8-bit II)-IMA


Optional

53 0404A01K

Signal cable-switcher-(D25 female)-(network port 8-bit III)


Optional

54 0404A03H

Single cable-RPS power cable-1m-(H2X7(4.20))-(18UL2464(14C))-(H2X7(4.20))-AR2921


Optional

55 0404A042

Single cable-trunk cable-3m-(D68 male-III)-(SYFVZ75-1.2/0.25*8)-(8*BNC75 straight male-V)-4E1-BNC


Optional

56 0404A043

Single cable-trunk cable-3m-(D68 male)-(8*28UL2464(2P)PWG1U-I)-(8*network port 8-bit-VI)-8T1-RJ45


Optional

57 0404A044

Single cable-trunk cable-3m-(D68 male)-(4*120CC2P0.4P430U(S))-(4*network port 8-bit-II)-4E1-RJ45


Optional

58 0404A045

Single cable-trunk cable-3m-(D68 male)-(4*28UL2464(2P)PWG1U-I)-(4*interface port 8-bit-VI)-4T1-RJ45


Optional

59 0404A048

Single cable-transit cable-0.5m-(interface port 8-bit-III)-(CC4P0.5 gray)-(interface port 8-bit-I)-ASE


Optional

60 0404A06C

Single cable-transit cable-5m-(D50 male-VI)-(100CC32P0.4P430U(S))-(24*interface port 6-bit-II)


Optional

61 0404A06D

Single cable-transit cable-15m-(D50 male-VI)-(100CC32P0.4P430U(S))-(24*interface port 6-bit-II)


Optional

62 0404A095

Single cable-SIC-8AS communication cable-0.28m-D60 male-8*CC8C0.32P296U(S)-(8*interface port 8-bit-III)-RJ45 female socket attached


Optional

63 0404A09D

Single cable-telephone line-3m-(interface port 8-bit-)-(26UL20251-4C black)-(interface port 8-bit-II)-STP


Optional

64 04060353 Single Cable, DS3 Video Cable, 15.00m, BNC75SM-V, SYFVZ75-1.2/0.25, SMB75SF-V, InfoLink DVS6000


Optional

65 04060368 External Power Cable, PGND, 3.00m,6mm^2-G&Y, OT6-8, 227IEC02-6^2G&Y, 2*OT6-6, NetEngine


Optional



No. Code Description Quantity Remarks 66 04060414 Trunk Cable, DS3 Input & Output, 30.00m,

75ohm, 2.2mm, BNC75SM-V, SYFVZ75-1.2/0.25, SMB75SF-V, InfoLink


Optional



Optional



Optional

Configuration description: 1. First, it should be clarified that the Quidway AR 19-1X series adopts a standard configuration in production and delivery; in other words, we only provide cables with the standard length, not the special length. There is no need for a field survey when selling through agents. However, a field survey is needed when selling together with other products of the company. In this case, the requirements raised should not be met through the list of the Quidway AR 19-1X series, and instead, such requirements should be accommodated through the configuration of other products. 2. The cables are closely related to the corresponding interface modules in the application. As for the distribution model of the agent, the configuration personnel can ignore the corresponding relation with the interface module. However, the marketing personnel need know the general application scenario for the regular cable. For bundling model and direct delivery to the users, you need know the corresponding cable selection for the correct interface module. 3. When the E1 cable with BNC connector on one end (and DB15 connector on the other), like 04026106, 04040148, 04040149, is selected, you still need to select two coaxial connectors (14040202) for each cable based on the 1:2 ratio. This is to facilitate the users or the customer service personnel to extend the length of the E1 cable. 4. When the E1 cable with RJ45 connector on one end (and DB15 connector on the other), like 04026104, 04026105, 04040150, 04040151, is selected, you still need to select one RJ45 connectors (14080099) for each cable based on the 1:1 ratio. This is to facilitate the users or the customer service personnel to extend the length of the E1 cable. 5. Note that for the Quidway AR 19-1X series, the host of the router has one AUX port and two Ethernet ports, however, no corresponding AUX port cable or Ethernet cable is in the host configuration. Therefore, proper AUX port cable and Ethernet cable need be considered in the solution design. 6. The types and quantities of the optional cables are related to the interface modules.



6 Configuration of External Cable Set of the Quidway AR 19-1X Series The Quidway AR 19-1X series can use the external optical fiber suite for the Quidway R2600&3600 series routers in the 8040 product family, and use the same suite of external optical fiber suite (04100053 external suite-Quidway3680 external optical fiber suite). The types and quantities of the optional optical fibers are related to the interface modules.

Table 35 Fiber optical suite of the Quidway AR 19-1X series


No. Code Description Quantity Remarks 1 14130098 Patch Cord, SC/PC-SC/PC, Single-mode,

3mm, 5m At customers' option

Optional

2 14130126 Patch Cord, SC/PC-SC/PC, Single-mode, 3mm, 15m


Optional

3 14130127 Patch Cord, SC/PC-SC/PC, Multi-mode, 3mm, 15m


Optional

4 14130134 Adapter, SC-SC, 2, Blue, Shell:Plastic, Sleeve:Zirconia, Square


Optional



Optional

6 14130153 Patch Cord, FC/PC-SC/PC, Multi-mode, 3mm, 10m


Optional



Optional

8 14130176 Patch Cord, SC/PC-SC/PC, Single-mode, 3mm, 2m


Optional



Optional

10 14130197 Patch Cord, FC/PC, LC/PC, Single-mode, 2mm, 10m


Optional



Optional

12 14130221 Patch Cord, FC/PC, LC/PC, Multi-mode, 2mm, 10m


Optional



Optional

14 14130248 Adapter, LC/PC-LC/PC, 2, Blue, Shell:Plastic, Sleeve:Zirconia, Square


Optional



Optional

16 14130253 Patch Cord, FC/PC-SC/PC, Single-mode, 3mm, 10m


Optional



No. Code Description Quantity Remarks 17 14130295 Patch Cord, LC/PC-LC/PC, Multi-mode,

2mm, 20m At customers' option

Optional



Optional



7 Configuration Examples The interfaces of the AR 19-1X router involved in this manual are simple, so the configuration examples are omitted.



8 Configuration FAQ

8.1 Although the routers have standard configurations without the need of on-site survey, in some of the bundled sales contracts, survey report is needed and some special requirements on the cable length are specified, especially the E1 cable. How to handle it?

Although we have emphasized repeatedly that the delivery of the mid-range-and-low-end routers should be prepared in standard configuration, however, in the tie-in sales, on-site survey is needed, and some special requirements may be posed. Here mainly concerns the cable length requirement. Take the length of the E1 cable as an example. The standard lengths of the cables we provided are 3m, 20m, and 40m. If the users require the length of 10m or 50m, the requirement cannot be satisfied in the product list directly. One end of the E1 cable of the router is always DB15, and the other end may be BNC or RJ45 according to the actual needs. Generally, unlike other products, this router cannot adopt the method of directly extending the length of the E1 cable. Here we suggest the following methods: We have mentioned in the earlier section of the configuration manual that when the E1 cable with BNC connector on one end (and DB15 connector on the other), like 04026106, 04040148, 04040149, is selected, you still need to select two coaxial connectors (14040202) for each cable based on the 1:2 ratio. This is to facilitate the users or the customer service personnel to extend the length of the E1 cable. When the E1 cable with RJ45 connector on one end (and DB15 connector on the other), like 04026104, 04026105, 04040150, 04040151, is selected, you still need to select one RJ45 connectors (14080099) for each cable based on the 1:1 ratio. This is to facilitate the users or the customer service personnel to extend the length of the E1 cable." The addition of the two connectors 14040202 and 14080099 is to facilitate the extension of the length of the E1 cable. For non-standard E1 cable, it is necessary to solve it by adopting standard length cable + connector + customized length of cable. The connection relationship is shown in the following figure.

Figure 13 Extension of 75Ω E1 cable

Cable 1

Cable 2

Router DDN

BNC male BNC male

SMA-SMB

BNC connector（14040202）

DB15

Cable 1 is the standard item in the configuration list, cable 2 is the non-standard cable, while BNC is the connector to connect cable 1 and cable 2. When the 75Ω E1 cable is used, the receiving/transmitting lines are separated, and therefore, two BNC connectors are needed.



Figure 14 Extension of 120Ω E1 cable

Cable 1

Cable 2

Router DDN

SMA-SMB

RJ45 connector（14080099）

DB15

RJ45 connector RJ45 connector

Cable 1 is the standard item in the configuration list, cable 2 is the non-standard cable, while RJ45 is the connector to connect cable 1 and cable 2. When the 120Ω E1 cable is used, only one RJ45 connector is needed.

8.2 The users complain that there is not any document in the package of the newly purchased E1 voice module, so they do not know how to use it.

As the host and the modules of a router are all ATO items (AI) and are delivered separately, each module has a packing box of itself, and in international deliveries, there are multiple types of SIC interface modules and two types of ESM modules. The varieties will keep increasing in the future. At first, we considered including corresponding documents in the packing boxes of the modules, but this would add 20 codes. Meanwhile, we see that the sales of all the routers including the modules are through the distributors, who will assemble and test the routers. Therefore, the products are not sent to the users directly. On the other hand, we have considered the consistency of the installation of the modules as much as possible. In other words, different types of the modules do not lead to significant difference in the installation methods. Besides, the modules will not be used without the host, and we have already included detailed installation manuals and CD-ROMs as accessories to the host in the delivery, which contains the installation and usage instructions for all the modules and software features. We are also watching on this issue and evaluating the impact of the current method in actual operations. In the future, we may add one more CD-ROM in the package containing some necessary information for all the modules, but this will increase the cost.

8.3 The optical fibers that the marketing personnel promised to the customers are too long that we cannot find them in the configuration list. How can we do with it?

The same is as the configuration of the E1 and other cables. Generally, the configuration of the mid-range-and-low-end routers has only standard optical fibers, without the on-site survey. However, in some cases, on-site survey is needed. In this case, the length of the fiber optical fibers in the list may not be able to meet the requirements of the contract. In this case, you need to follow the Configuration Specifications of Ultra-long Haul Optical Fibers of Datacom Products of the company. Parts of the specifications are as follows: In the order, it should follow strictly the optical fiber length and connectors specified in the on-site survey and make them optional items in the configuration list. If there are no suitable items in the optical fiber suite, follow the principles below for configuration.



1. If the optical fibers and connectors specified in the on-site survey are within the configuration list, but the types are not right, the upward principle is adopted, with deviation of less than 5m. For example, if the survey requires Optical connector-MTRJ-2SC/PC-multi-mode-2mm parallel-45m However, in the actual list, there is 14130243 Optical connector-MTRJ-2SC/PC-multi-mode-2mm-parallel-50m Then, you may choose 14130243. 2. The connectors that the survey report requires are in the list, but the length is not right. The deviation is over 5m and the upward principle is adopted. The delivery configuration should use the code that best fits the length as much as possible, specifying the actual length needed so that the coordinator can notify the purchasing personnel to make special purchases. 3. The length of the fibers that the survey requires is in the list, but the fiber connectors are not right. In the delivery configuration, the code of the length should be used in placing an order, but right types of fiber connectors should be specified so that the coordinator can notify the purchasing personnel to make special purchases. 4. All datacom products (including international delivery) should follow the requirements in 1, 2, and 3 above. If they are in conflict with the configuration manual, these requirements should be obeyed. When the configuration manual is upgraded, revisions should be made to the manual according to these requirements.



9 Appendix: Slot Restriction for Host Interface Card Users are recommended to consult the table below for the interface module configuration when using Quidway AR 19-1X series routers.

Note √ means the router can support the interface card or the interface module. × means the router cannot support the interface card or the interface module.

9.1 SIC/DSIC Configuration Table

Table 36 SIC/DSIC configuration table of the Quidway AR 19-1X series

Interface Module Type 19-10/19-10-W 19-13-I/19-15-I 19-13-IW/19-15-IW

RT-SIC-1GEC √ √ √

RT-SIC-4FSW √ √ √

RT-DSIC-9FSW √ √ √

RT-SIC-1VE1 × × √[1]

RT-SIC-1BS-V2 √ √ √

RT-SIC-1BU-V2 √ √ √

RT-SIC-1BSV √ √ √

RT-SIC-2BSV √ √ √

RT-SIC-1FEF √ √ √

RT-SIC-2FXS1FXO √ √ √

RT-SIC-1FEA √ √ √

RT-SIC-1SAE √ √ √

RT-SIC-1E1-F √ √ √

RT-SIC-EPRI √ √ √

RT-SIC-1FXS-V2 √ √ √

RT-SIC-2FXS-V2 √ √ √

RT-SIC-1FXO-V2 √ √ √

RT-SIC-2FXO-V2 √ √ √

RT-SIC-1ADSL-I √ √ √

RT-SIC-1ADSL √ √ √

RT-SIC-1AM-V3 √ √ √

RT-SIC-2AM-V3 × × ×

Note:

√: The item ticked (√) without special description means the slot supports the function.

[1]: If RT-SIC-1VE1 cannot be supported without VPM, the VPM must be added.



9.2 VPM Card Configuration Table

Table 37 VPM configuration table of the Quidway AR 19-1X series

Interface Module Type 19-10/19-10-W 19-13-I/19-15-I 19-13-IW/19-15-IW

VPM32 × × √

VPM24 × × √

VPM16 × × √

VPM8 × × √

Quidway AR 19-1X Router Hardware Configuration Manual _Overseas Version_V1

Documents

Transcript of Quidway AR 19-1X Router Hardware Configuration Manual _Overseas Version_V1