Quick Tips to Patch Get Started - iHealthSpot Interactive
2
STEP 1: TURN ON & SET-UP MONITOR Power ON monitor and follow the on-screen instructions. When prompted, select the appropriate language option and press Continue. Press the blue arrow on the image that says “Patch”. Open a pouch and place the patch on a flat, hard surface. Pick up the sensor and place in the patch. While standing, place your hand on top of the sensor and apply pressure to snap into patch. STEP 2: ATTACH SENSOR TO THE PATCH Quick Tips to Get Started MOBILE CARDIAC OUTPATIENT TELEMETRY Inspect all four sides of the sensor for gaps. Apply pressure to all four corners to ensure the sensor is sealed properly. Rotate the patch 180 degrees, again apply pressure to snap the sensor into the patch. STEP 3: CHECK FOR GAPS Pick up the sensor and the patch so it is near the monitor. The sensor and monitor should automatically link to each other via Bluetooth. STEP 4: PAIR THE SENSOR AND MONITOR STEP 5: PATIENT CONSENT Consenting to Terms and Conditions of the Service Agreement, on the Patient Consent screen, is required to start monitoring. If you select “No”, the following screen will instruct you to contact BioTel Heart. OVER
Transcript of Quick Tips to Patch Get Started - iHealthSpot Interactive
STEP 1: TURN ON & SET-UP MONITOR
Power ON monitor and follow the on-screen instructions. When prompted, select the appropriate language option and press Continue.
Press the blue arrow on the image that says “Patch”.
Open a pouch and place the patch on a flat, hard surface.
Pick up the sensor and place in the patch.
While standing, place your hand on top of the sensor and apply pressure to snap into patch.
STEP 2: ATTACH SENSOR TO THE PATCH
Quick Tips to Get Started
MOBILE CARDIAC OUTPATIENT TELEMETRY
Inspect all four sides of the sensor for gaps. Apply pressure to all four corners to ensure the sensor is sealed properly.
Rotate the patch 180 degrees, again apply pressure to snap the sensor into the patch.
STEP 3: CHECK FOR GAPS
Pick up the sensor and the patch so it is near the monitor. The sensor and monitor should automatically link to each other via Bluetooth.
STEP 4: PAIR THE SENSOR AND MONITOR
STEP 5: PATIENT CONSENT
Consenting to Terms and Conditions of the Service Agreement, on the Patient
Consent screen, is required to start monitoring. If you select “No”, the following screen will instruct you to contact BioTel Heart.
OVER
CardioNet, LifeWatch, and BioTel Heart are trademarks of BioTelemetry, Inc.1000 Cedar Hollow Road, Suite 102, Malvern, PA 19355 | 1.866.426.4401 | gobio.com/patients Copyright © 2018. All rights reserved. Doc. 220-0440-01 Rev A
Remove the liner underneath the patch. Place the patch on slight angle. Press all four sides of the patch.
LEFTRIGHT
STEP 7: APPLY THE PATCH TO YOUR SKIN
A baseline ECG recording will begin automatically when you see this screen.
STEP 9: RECORD A BASELINE
STEP 8: REMOVE TOP PAPER
LEFTRIGHT
Remove top white paper. Smooth wrinkles. Wait 10-15 minutes before proceeding to the next step. When you are ready press Continue on the monitor screen.
Refer to the Patient Education Guide for complete instructions.Video tutorials are available at www.gobio.com/patients. For additional assistance, contact Customer Service toll-free at 1.866.426.4401.
Measure three finger widths below the left collarbone. If needed, shave area where the patch will be placed.
Clean skin with soap and water.
Scrub cleaned skin with firm pressure for one minute using the Prep Scrub from the MCOT Skin Prep Pack.
STEP 6: PLACEMENT AND SKIN PREP
LEFTRIGHT
Quick Tips to Get Started
(continued)
MOBILE CARDIAC OUTPATIENT TELEMETRY
![Copyright 2009, iHealthSpot, Inc. Internet Marketing Overview Presented By [Your Name]](https://static.fdocuments.net/doc/165x107/55142c145503466d1a8b4da3/copyright-2009-ihealthspot-inc-internet-marketing-overview-presented-by-your-name.jpg)
