Quick Installation Guide - planet.com.tw · 9 10 P1 P2 FAULT Ring R.O. 9 1000 LNK/ACT 1000 LNK/ACT...
Transcript of Quick Installation Guide - planet.com.tw · 9 10 P1 P2 FAULT Ring R.O. 9 1000 LNK/ACT 1000 LNK/ACT...
L2+ Multi-Port Full Gigabit Managed Ethernet Switch
IGS-10020MT / IGS-10020PT / IGS-10020HPT /
IGS-10080MFT / IGS-20040MT
Quick Installation Guide
Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Wiring the Power Inputs .............................................................................. 5
4. Terminal Setup ........................................................................................... 8
5. Logon to the Console .................................................................................. 9
6. ConfiguringIPaddress ...............................................................................10
7. Starting Web Management .........................................................................13
8. Resetting the Switch to Default ..................................................................16
9. Customer Support .....................................................................................18
3
1. Package ContentsThank you for purchasing PLANET L2+ Industrial Managed Switch, IGS-10020Series / IGS-10080MFT / IGS-20040MT. The descriptions of these models are asfollows:
IGS-10020MT:Industrial8-Port10/100/1000T+2-Port100/1000XSFPManagedSwitch
IGS-10020PT:Industrial8-Port10/100/1000T802.3afPoE+2-Port100/1000XSFPManagedSwitch
IGS-10020HPT:Industrial8-Port10/100/1000T802.3af/atPoE+2-Port100/1000XSFPManagedSwitch
IGS-10080MFT:Industrial8-Port100/1000XSFP+2-Port10/100/1000TManagedSwitch
IGS-20040MT:Industrial16-Port10/100/1000T+4-Port100/1000XSFPManagedSwitch
“Industrial Managed Switch” mentioned in this Quick Installation Guide referstotheabovefivemodels.
Open the box of the Industrial Managed Switch and carefully unpack it. Theboxshouldcontainthefollowingitems:
z TheIndustrialManagedSwitchx1
z QuickInstallationGuidex1
z DIN Rail Kit x 1
z Wall Mounting Kit x 1
z DB9 to RJ45 Interface RS232 Console Cable x 1
(ForIGS-10020PT/IGS-10020HPT/IGS-10080MFT/IGS-20040MT)
z DustCap(Pleaserefertothetablebelow)
RJ45 Dust Cap SFP Dust Cap
IGS-10020MT 8 2
IGS-10020PT 9 2
IGS-10020HPT 9 2
IGS-10080MFT 3 8
IGS-20040MT 17 4
4
Ifanyofthesearemissingordamaged,pleasecontactyourdealerimmediately.Ifpossible,retainthecartonincludingtheoriginalpackingmaterialstoenableyoutorepacktheproductincasethereisaneedtoreturnittousforrepair.
2. RequirementsThe Industrial Managed Switch provides remote login interface for managementpurposes. The following equipment is necessary for further management:
WorkstationisinstalledwithEthernetNIC(NetworkInterfaceCard)
Choiceof Internetbrowsers includesWindowsXP/2003,Vista,Windows7,MACOS X, Linux, Fedora, Ubuntu or other platforms compatible with TCP/IP proto-cols.
z The aboveworkstation is installedwithWebbrowser and JAVA runtimeenvi-ronmentplug-in.
Ethernet Port connection
z Usestandardnetwork(UTP)cableswithRJ45connectors.
Note
It is recommended touse InternetExplore7.0or above toaccesstheIndustrialManagedSwitch.
5
3. Wiring the Power InputsThe Upper Panel of the Industrial Managed Switch indicates a DC inlet powersocketandconsistsofoneterminalblockconnectorwithin6contacts.Pleasefollowthe steps below to insert the power wire.
1.Insertpositive/negativeDCpowerwires intocontacts1and2 forPower1,or5,and6forPower2.
IGS-10020MT: DC 12~48V, AC 24V
InputDC 12V~48V, AC 24V
V1- V1+
PWR1
V2- V2+
PWR2Fault
Figure 3-1: IGS-10020MT Upper Panel
IGS-10020PT / IGS-10020HPT: DC 48V
Figure 3-2: IGS-10020PT / IGS-10020HPT Upper Panel
6
IGS-10080MFT: DC 12~48V, AC 24V
Input DC 12V~48V
V1- V1+V2- V2+
PWR1PWR2 Fault
1A@24V
Figure 3-3: IGS-10080MFT Upper Panel
IGS-20040MT: DC 12~48V, AC 24V
Input DC 12-48V AC 24V
DC1 DC2Fault
DI 0 DI 1 DO 0 DO 1 GND GND
Figure 3-4: IGS-20040MT Upper Panel
7
Tightenthewire-clampscrewsforpreventingthewiresfromloosening.
1 2 3 4 5 6Power 1 Power 2+ - + -
Note
Thewiregauge for the terminalblockshouldbe in therange from12to24AWG.
8
4. Terminal SetupToconfigurethesystem,connectaserialcabletoaCOMportonaPCornotebookcomputerandtoRJ45typeserial (console)portof theManagedIndustrialSwitch.TheconsoleportoftheIndustrialManagedSwitch isDCEalready,sothatyoucanconnecttheconsoleportdirectlythroughPCwithouttheneedofnullmodem.
PC / Workstationwith
Terminal emulation software
RJ45 to DB9 RS-232 CableSerial Port
IP Address:192.168.0.100
IGS Industrial Managed Switch
A terminal program is required to make the software connected to the IGSIndustrial Managed Switch. Windows’ Hyper Terminal program may be a goodchoice.TheHyperTerminalcanbeaccessedfromtheStartmenu.
1. Click START,thenPrograms, AccessoriesandthenHyper Terminal.
2.When the following screen appears, make sure that the COM port should beconfiguredas:
Baud :115200
Parity : None
Data bits : 8
Stop bits : 1
FlowControl :None
9
5. Logon to the ConsoleOnce the terminal has been connected to the device, power on the IndustrialManagedSwitchandtheterminalwilldisplay“runningtestingprocedures”.
Note
1.TherearefourswitcheswithRJ45typeconsoleconnector.(IGS-10020PT/IGS-10020HPT/IGS-10080MFT/IGS-20040MT)
2.Let’stakeIGS-20040MTforexample.
When the following dialog box shown in Figure 5-1 appears, please enter thefactorydefaultusername“admin” andpassword“admin”.
Username:adminPassword:admin
Figure 5-1: Console Login screen
Note
1.Forsecurityreason,pleasechangeandmemorizethenewpass-wordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-face.
10
6.ConfiguringIPaddressTheIndustrialManagedSwitchisshippedwithdefaultIPaddressshownbelow:
IPAddress:192.168.0.100Subnet Mask: 255.255.255.0
TocheckthecurrentIPaddressormodifyanewIPaddressfortheSwitch,pleaseusetheproceduresasfollows:
Display of the current IP Address1. At the “#”prompt,enter“show ip interface brief”.
2.ThescreendisplaysthecurrentIPaddressshowninFigure5-1.
Figure 6-1: IP Information Screen
11
Configuration of the IP Address3. At the “#”prompt,enterthefollowingcommandandpress<Enter> as shown inFigure5-2.
IGS-20040MT# configure terminalIGS-20040MT(config)# interface vlan 1IGS-20040MT(config-if-vlan)# ip address 192.168.1.100 255.255.255.0
The previous command would apply the following settings for the IndustrialManagedSwitch.
IPAddress:192.168.1.100Subnet Mask: 255.255.255.0
Figure 6-2: Configuring IP Address Screen
4.Repeatstep1tocheckiftheIPaddressischanged.
12
Store the current switch configuration5. At the “#”prompt,enterthefollowingcommandandpress<Enter>.
# copy running-config startup-config
Figure 6-3: Saving Current Configuration Command Screen
If the IP is successfully configured, the Industrial Managed Switch will apply thenew IP address setting immediately. You can access the Web interface of theIndustrialManagedSwitchthroughthenewIPaddress.
Note
If you are not familiar with the console command or the relatedparameter, enter “help” anytime in console to get the help description.
13
7. Starting Web ManagementThe following shows how to start up the Web Management of the IndustrialManaged Switch. Note the Industrial Managed Switch is configured through anEthernet connection. Please make sure the manager PC must be set on the same IPsubnetaddress.
For example, the default IP address of the Industrial Managed Switch is192.168.0.100, then the manager PC should be set at 192.168.0.x (where xis a number between 1 and 254, except 100), and the default subnet mask is255.255.255.0.
IP Address:192.168.0.x IP Address:
192.168.0.100
IGS Industrial Switch
RJ45/UTP-Cable
Figure 7-1: IP Management Diagram
Logging in the Industrial Managed Switch1.Use Internet Explorer 7.0 or above for Web browser and enter IP address
http://192.168.0.100 (the factory-default IP address) to access the Webinterface.
2.When the following dialog box appears, please enter the default user name“admin”andpassword“admin”(orthepasswordyouhavechangedbefore)asshowninFigure7-2.
DefaultIPAddress:192.168.0.100DefaultUserName:adminDefaultPassword:admin
14
Figure 7-2: Login Screen
3.Afterenteringthepassword,themainscreenappearsasshowninFigure7-3.
Figure 7-3: Web Main Screen of Industrial Managed Switch
15
4. The Switch Menu on the left of the Web page lets you access all the functions andstatustheIndustrialManagedSwitchprovides.
Now, you can use the Web management interface to continue the Switchmanagement. Please refer to the user manual for more.
Note
For security reason, please change and memorize the new pass-wordafterthisfirstsetup.
16
8. Resetting the Switch to Default To reset the IP address to the default IP Address “192.168.0.100” and theuser password to factory default mode (default password is admin), press thehardwareresetbuttononthefrontpanelforabout10seconds.Afterthedevice isrebooted,youcan loginthemanagementWeb interfacewithinthesamesubnetof192.168.0.xx and default password. Be noted that all the previous setupswill bedisappearedafterthefactorydefaultresetismade.
Mini-GBIC
100/1000X SFP
RESET
ACTLNK
109
P1 P2 FAULT
Ring R.O.
9
LNK/ACT1000LNK/ACT1000
10
ACTLNK
1000Reset Button
Figure 8-1: IGS-10020MT Reset Button
ACTLNK
IGS-10020HPT
9
LNK/ACT1000LNK/ACT1000
10
8
6
4
2
7
5
3
1
RESET
9
Console
115200,N,8,1
P1 P2
Ring R.O.
FAULT
10
100/1000X SFP
10/100/1000T
ACTLNK
PoE In-Use
802.3at PoE
Reset Button
Figure 8-2: IGS-10020PT / IGS-10020HPT Reset Button
17
Reset Button
Figure 8-3: IGS-10080MFT Reset Button
1
3
5
2
4
6 17
RESET
Console
P1 P2
Ring R.O.
FAULT
Reset Button
Figure 8-4: IGS-20040MT Reset Button
18
9. Customer SupportThank you for purchasing PLANET products. You can browse our online FAQresourceonPLANETwebsitefirsttocheckif itcouldsolveyourissue.Ifyouneedmoresupportinformation,pleasecontactPLANETswitchsupportteam.
PLANETonlineFAQ:http://www.planet.com.tw/en/support/faq.php
Switchsupportteammailaddress:[email protected]
IGS-10020MT / IGS-10020PT / IGS-10020HPT / IGS-10080MFT / IGS-20040MTUser’sManual:
http://www.planet.com.tw/en/support/download.php?type1=22153&model=&type=3
(PleaseselectyourswitchmodelnamefromProductModeldropdownmenu)
Copyright © PLANET Technology Corp. 2014.Contents are subject to revision without prior notice.PLANET is a registered trademark of PLANET Technology Corp.All other trademarks belong to their respective owners.