The XChanger Combo Kit allows you to completely retrofit your paper dispenser and waste receptacle with the XLERATOR or XLERATOReco hand dryer. This panel is easily installed over the space left by the former paper dispenser and will not cause damage to the existing wall surface. The XLERATOR or XLERATOReco hand dryer with ADA compliant Recess Kit is installed into the XChanger leaving your restroom modern, clean and green.

AFTERBEFORE

XLERATOR®/XLERATOReco® HAND DRYER XCHANGER® COMBO KIT (HAND DRYER NOT INCLUDED)

QUICK CHANGE

XLERATOR®/XLERATOReco® HAND DRYER XCHANGER® COMBO KIT

40502 Recess Kit, Brushed Stainless Steel $180 (for ADA 4” protrusion requirements)

40550 XChanger, Brushed Stainless Steel $220 (Use with #40502 Recess Kit)

40551 XChanger, Brushed Stainless Steel, ADA Height $220 (Use with #40502 Recess Kit)

40575 XChanger Combo Kit: $400 Comes with ADA Recess Kit #40502 and Standard XChanger #40550

40576 ADA XChanger Combo Kit: $400 Comes with ADA Recess Kit #40502 and ADA Height XChanger #40551

XCHANGER SPECIFICATIONSWeight: 17 Lbs. (7.7 kg)

Overall Dimensions: 17 ¼” wide x 56” high x 1” deep

Rough Wall Opening: XChanger is installed over the footprint of most common paper towel dispenser/waste receptacles or approximately 17 ¼” wide x 56” high

Installation Guide (Consult local ADA codes): The XChanger is a retrofitable conversion kit which will enable you to update your existing paper towel dispenser and waste receptacle to an XLERATOR or XLERATOReco hand dryer. Used in conjunction with the Recess Kit, the XChanger is installed over the footprint of common paper towel dispenser/waste receptacles designed to match their dimensions so there is little or no wall repair required once the XChanger kit is installed.

ADA Height XChanger Kit: The XChanger also comes in an ADA version. The opening to the unit is 7” lower to allow the recess kit and XLERATOR or XLERATOReco hand dryer to be ADA compliant. Check local regulations for actual ADA compliance rules.

CONSTRUCTIONXChanger is fabricated of 18 gauge 18-8 type 304 stainless steel with #4 satin finish. All welded construction.

RECESS KIT SPECIFICATIONSWidth: 16 3⁄8” (416 mm) Height: 26” (660 mm)

Depth: 3 3⁄8” (86 mm) Weight: 11 lbs. (4.99 kgs.)

Installation Guide (Consult local ADA codes): An ADA-compliant Recess Kit for XLERATOR or XLERATOReco hand dryer models that adheres to the 4” protrusion ADA guidelines in a restroom walkway and helps keep water off the wall and floor. When installed, bottom of hand dryer will be 10” (254 mm) above bottom of rough wall opening. Therefore, bottom of rough wall opening should be 10” (254 mm) below suggested mounting height for hand dryer. (See suggested mounting heights above).

CONSTRUCTIONWall box is fabricated of 22 GA 18-8 type 304 stainless steel with #4 satin finish with 16 GA 18-8 type 304 stainless steel dryer mounting plate. All welded construction.

NATIONAL INSTALLATION SERVICES AVAILABLE CALL FOR DETAILS 800-255-9235

XCHANGER COMBO KITPART #40575 - STANDARDPART #40576 - ADA HEIGHT

PART #40550 - STANDARDPART #40551 - ADA HEIGHT

(XLERATOR Hand Dryer not included)

PART #40502

Part ID Description List Price

TIME TO THROW IN THE TOWEL®

E X C E L D R Y E R I N C • 1 . 8 0 0 . 2 5 5 . 9 2 3 5 • E X C E L D R Y E R . C O M2017

APRIL

16XCS0008