Quark-elec GSM WiFi remote control AIS Receiver - …Quark-Elec Application Note 1 of 13 2014 V1.1...

13
Quark-Elec Application Note http://www.quark-elec.com 1 of 13 2014 V1.1 QK-W011 WiFi Remote Controller Application Notes Features Turn Electronics ON or OFF from Mobile Phones Remote Control from 50 Meters with WiFi Android & iOS App Instant Set Up Up to 4 Mobiles Phones per Unit Switching Electronics through Relays or 433MHz RF Power Sockets Master ON/OFF Turn Everything on with One Click Waterproof Enclosure UK, Europe & USA RF Power Sockets Available Applications Control Lighting, Electrical Appliance Garage Doors, Shutters Automation Application Remote Maintenance Irrigation Systems Plant Maintenance Valve Control Pumping Station Oil/gas Pipelines Control Security Systems PLC and Automation System

Transcript of Quark-elec GSM WiFi remote control AIS Receiver - …Quark-Elec Application Note 1 of 13 2014 V1.1...

Quark-Elec Application Note

http://www.quark-elec.com 1 of 13 2014

V1.1

QK-W011 WiFi Remote Controller Application Notes Features Turn Electronics ON or OFF from Mobile Phones

Remote Control from 50 Meters with WiFi

Android & iOS App

Instant Set Up

Up to 4 Mobiles Phones per Unit

Switching Electronics through Relays or 433MHz RF Power Sockets

Master ON/OFF –Turn Everything on with One Click

Waterproof Enclosure

UK, Europe & USA RF Power Sockets Available

Applications

Control Lighting, Electrical Appliance

Garage Doors, Shutters

Automation Application

Remote Maintenance

Irrigation Systems

Plant Maintenance

Valve Control

Pumping Station

Oil/gas Pipelines Control

Security Systems

PLC and Automation System

Quark-Elec Application Note

http://www.quark-elec.com 2 of 13 2014

V1.1

Document History

Issue Date Changes / Comments

1.0 21-12-2013 Initial release

1.1 08-04-2014 USA type main sockets available

Order Information

Part No Description

QK-W011 WiFi Remote controller (only three relays output, no RF 433MHz module and RF plug sockets)

QK-W011UK WiFi Remote controller with three RF 433MHz UK type main sockets

QK-W011EU WiFi Remote controller with three RF 433MHz Europe type main sockets

QK-W011US WiFi Remote controller with three RF 433MHz USA type main sockets

Quark-Elec Application Note

http://www.quark-elec.com 3 of 13 2014

V1.1

Contents

1 INTRODUCTION ................................................................................................................... 3

2 SETUP ................................................................................................................................... 4

2.1 POWER UP .......................................................................................................................... 4 2.2 ACCESS QK-W011 .............................................................................................................. 4 2.3 RESET................................................................................................................................. 5

3 APP(ANDROID VERSION) ................................................................................................... 5

3.1 CONNECT WITH MOBILE PHONES.......................................................................................... 5 3.2 RESET PASSWORD ............................................................................................................... 7 3.3 RENAME THE PORT .............................................................................................................. 8

4 PARING WITH RF POWER SOCKETS ................................................................................ 9

5 HARDWARE........................................................................................................................ 10

5.1 CONNECTIONS ................................................................................................................... 10 5.2 RF MAIN SOCKETS ............................................................................................................. 10 5.3 ENCLOSURE ...................................................................................................................... 11

6 OPERATING SPECIFICATIONS ........................................................................................ 12

1 INTRODUCTION

QK-W011 series remote controller is a versatile device which can be attached to many of

electronic devices in homes, offices, plants, or wherever you need. Operators can control any

remote equipments, heater, lights, machines, or power sockets through WiFi network. QK-W011

support three relay outs and 433MHz RF transmitter. RF power sockets within 25 meters of QK-

W011 can be controlled by mobile operators.

Quark-Elec Application Note

http://www.quark-elec.com 4 of 13 2014

V1.1

Figure 1 System diagram

2 SETUP

2.1 Power up

QK-G021/022 module can be powered by 12VDC. Connect a 12 volt DC power supply to

the power socket, switch on the power supply. The indicator LED will turn on once system

finish initialization. This LED indicator flashes quickly if any wireless data transmit.

2.2 Access QK-W011

After 30 seconds of powering on, customer should be able to search an AP called

‘WiFi168’. Access WLAN of your phone and connect with the ‘WiFi168’. The default

password is ‘88888888’.

Figure 2 Search AP

Quark-Elec Application Note

http://www.quark-elec.com 5 of 13 2014

V1.1

Figure 3 Search AP

2.3 Reset

QK-W011 can be reset to factory setting by the following process:

1, Power off QK-W011.

2, Press and hold the ‘RESET’ button, and then power up QK-W011.

3, Wait 5 seconds, and the release ‘RESET’ button. Wait another 5 seconds, the indicator LED

should turns on.

4, During the LED ‘on’ state, power off QK-W011 again the system should reset to the factory

setting.

3 APP(ANDROID VERSION)

The latest version of Android APP can be downloading with the following link:

http://www.quark-elec.com/down/class/?3.html

3.1 Connect With Mobile phones

Once open the APP, enter ‘192.168.1.100’ in the IP bar and ’5000’ in the port bar (for some old

QK-W011, this should be ‘1’). Then click ‘Connect’, then WiFi icon should change to blue, this

indicated the connection has been successful setup.

Quark-Elec Application Note

http://www.quark-elec.com 6 of 13 2014

V1.1

Figure 4 Control Panel on App

Once the mobile phone has connected with QK-W011, the operator can control these

electronics devices which connected on relays and RF main sockets. The indicator icons

(the light bulb next to ‘Off’ button) can demonstrator each relays/main socket settings.

Figure 5 Indicator of the setting

This icon changes from gray

to blue once the WiFi

connection setup.

These icons indicate the

status of the relays/switches.

Quark-Elec Application Note

http://www.quark-elec.com 7 of 13 2014

V1.1

3.2 Reset password

Operators can change the WiFi password once connected with QK-W011 module. The

password should be 7 to 17 characters long. New password will not be active until re-power

QK-W011(Unplug the power header and connect again).

Figure 6 Change password

Quark-Elec Application Note

http://www.quark-elec.com 8 of 13 2014

V1.1

Figure 7 Password setting

3.3 Rename the port

Operators can rename the three relay outputs and three RF main sockets as meaningful names

through settings on App.

Figure 8 Rename the port

Quark-Elec Application Note

http://www.quark-elec.com 9 of 13 2014

V1.1

4 PARING WITH RF POWER SOCKETS

QK-W011 has a build-in 433Mhz RF transmitter module. It can pair with up to four RF power

sockets. So the operators are able to turn ON/OFF the electrical devices by switching the

power sockets.

The power sockets have been paired and ready to use if they come with QK-W011. However

the operator can always pair or release the pairing by following steps:

Insert the RF power socket into a powered mains wall socket.

The LED light on the socket should flash at 1 second intervals indicating it’s ready to

pair with the QK-W011. If the lights doesn’t flash, press and hold the ON/OFF button for

5 seconds to clear the memory indicated by the quickly flashing LED.

Open WiFi Remote control panel in App, press the corresponding RF switch ‘ON’

button. The paring command will be sending out through RF signals.

Figure 8 RF Switch ON buttons

Once the power socket received the paring command, The LED light on the socket will

flash briefly more quickly and then flash at 1 second intervals. This RF main socket

should have been successfully paired now.

Repeat above process for each different RF main sockets.

Simply plug-in the appliance which you want to operate remotely into the socket, press the

corresponding ON button on App that is paired to the socket. The appliance will turn on.

Quark-Elec Application Note

http://www.quark-elec.com 10 of 13 2014

V1.1

5 HARDWARE

5.1 Connections

General view of the module is show as below and details of each connection are described on it.

QK-W011 use 12VDC 1.0Amp power. The outside and inner diameter of the plug is 5.5mm and

2.1mm.

Figure 9 QK-W011mechanical drawing

5.2 RF main sockets

Customer can select USA, European or UK type RF main sockets. Like most of the similar RF

main sockets in the market, customer should keep at least 0.2 meter distance between one RF

main socket and the other. This is due to EMC interference between these RF main sockets.

NC

1

NO

1

CO

M1

C

OM

1

NC

2

NO

2

CO

M1

C

OM

2

NC

3

NO

3

CO

M1

C

OM

3

12V

RF aerial

Reset

CO

M1

Quark-Elec Application Note

http://www.quark-elec.com 11 of 13 2014

V1.1

Although QK-W011 have running specific algorithm to increase the RF transmission reliability,

Quark-elec cannot guarantee 100% of proper action rate of RF main sockets. QK-W011 RF

signal could be affect by other nearby RF devices such as bell ring, car key, cordless phone,

mobile phone, RF alarm system. The following is a real test result taken in a house

environment in the UK.

Distance between QK-W011 and

433Mhz RF main sockets

Proper action rate (RF main sockets been

successfully trigged by QK-W011)

2 meters 100.0%

5 meters 100.0%

8 meters 98.1%

10 meters 96.9%

15 meters 95.2%

20 meters 92.2%

5.3 Enclosure

IP56 Insulation Class 2 plastic enclosure, 115mm*90*40 external dimension is used for QK-

W011.

Quark-Elec Application Note

http://www.quark-elec.com 12 of 13 2014

V1.1

Figure 9 Enclosure drawing

6 OPERATING SPECIFICATIONS

Item Specification

Operating Temperature -25°C to +80°C

Storage Temperature -40°C to +85°C

DC Supply 12.0V(+/-10%)

Average Supply Current (typical

quiescent)

160mA

Supply Current in Busy Period(data

transmission)

190mA

WLAN Standard IEEE 802.11 b/g/n

Operating Frequency 2.4000 to 2.4835 GHz

Receive Sensitivity -85 dBm @ 11Mbps, -70 dBm @ 54Mbps

Transmit Mean Output Power +17 dBm for 802.11b, +13 dBm for 802.11g, +12 dBm for

802.11n

WiFi Antenna Build-in module U.FL antenna connector

Quark-Elec Application Note

http://www.quark-elec.com 13 of 13 2014

V1.1

Encryption Support for WEP40/64, WEP104/128, WPA-PSK, WPA2-

PSK, AES and TKIP

433Mhz Transmitting Power 1W

433Mhz Modulation Mode ASK (AM)

RF Transmission Power <10mW

RF Emission Distance 25 to 50 meters (open air condition)

Rated Current on Relay 7A240VAC

Rated Voltage on Relay 90V-245V

For more technical information and enquires please go to Quark-elec forum:

http://quark-elec.com/forum/

For sales and purchasing information, please email us: [email protected]

Quark Electronics (UK)

24 Meadowbank

Hitchin

Herts. UK

SG4 0HY