,QTM-eLED DimNo v2legacy.q-tran.com/sites/default/files/QOM-eLED_2015_8_4.pdf · 2018. 9. 27. ·...
Transcript of ,QTM-eLED DimNo v2legacy.q-tran.com/sites/default/files/QOM-eLED_2015_8_4.pdf · 2018. 9. 27. ·...
Output Load Output Load Output Load Input LoadNEU HOT GND
QOM-eLED Power Supply Installation Instructions
Driver with no Dimming Module
LED DRIVER 1 (120 - 277V)
LED DRIVER 2 (120 - 277V)
LED DRIVER 3 (120 - 277V)
A B C
CBA ABC
separate Inputs available; see next page.*
Output Load Output Load Output Load Input LoadNEU HOT GND
QOM-eLED Power Supply Installation Instructions
Driver with no Dimming Module
LED DRIVER 1 (120 - 277V)
LED DRIVER 2 (120 - 277V)
LED DRIVER 3 (120 - 277V)
A B C
Input LoadNEU HOT GND
Input LoadNEU HOT GND
C
A B
BA C
Output Load Output Load Output Load Input LoadNEU HOT GND
LED DRIVER 1 (120 - 277V)
LED DRIVER 2 (120 - 277V)
LED DRIVER 3 (120 - 277V)
0 - 10VDIM-MOD 3
0 - 10VDIM-MOD 2
0 - 10VDIM-MOD 1
Dimmer control
BL
RD
BL
RDRD
BL
RD
QOM-eLED Power Supply Installation Instructions
Driver with Dimming Module
A B C
A B C
separate Inputs available; see next page.* separate 0-10v dim mods available; see next page.*
Output Load Output Load
LED DRIVER 1 (120 - 277V)
LED DRIVER 2 (120 - 277V)
LED DRIVER 3 (120 - 277V)
0 - 10VDIM-MOD 3
0 - 10VDIM-MOD 2
0 - 10VDIM-MOD 1
Dimmer control
BL
RD
BL
RDRD
BL
RD
QOM-eLED Power Supply Installation Instructions
Driver with Dimming Module
A B C
A B C
Dimmer control
Dimmer controlOutput Load
Input LoadNEU HOT GND
A
Input LoadNEU HOT GND
B
Input LoadNEU HOT GND
C
A B
C
Output Load Output Load Output Load Input LoadNEU HOT GND
LED DRIVER 1 (100 - 277V)
LED DRIVER 2 (100 - 277V)
LED DRIVER 3 (100 - 277V)
0 - 10VDIM-MOD 1
0 - 10VDIM-MOD 2
0 - 10VDIM-MOD 3
Dimmer control
A B C
A B C
PRIMARYSECONDARY
14.5”
9.0”
4.25”
14.5”
9.0”
Wire Size
LED
Syste
m24
VDC
60 60 50/600.60/0.29 0.95/0.40
1.90/0.80
2.85/1.20
1.20/0.58
1.80/0.87
50/60
50/60
50/60
50/60
50/60
120 120
180 300
200 200
100100
300180
0-10V DIMWith Without
0-10V DIMWith Without
OUTPUT 12 VDC
QOM-eLEDOUTPUT 24 VDC
INPUT 100/277 V INPUT 100/277 V
INPUT (A) FREQUENCY INPUT (A) FREQUENCY
12VD
C
w 10 AWG(5.6mm2) (3.3mm2) (1.3mm2) (0.78mm2) (0.50mm2) (0.33mm2) (0.2mm2) (0.13mm2)(2.0mm2)
12 AWG 14 AWG 16 AWG 18 AWG 20 AWG 24 AWG22 AWG 26 AWG
12 500240100706480300150120
2119 76 48 30 18 1114157 36 23 14 9 65924 15 10 6 4 2415168 107 67 42 26 16282114 73 46 29 18 1117671 45 29 18 11 78836 23 14 9 5 37129 18 11 7 4 3
256017254080
100
19292382711851155846
Limited output voltage and current, plus isolation for safe operation Dimmable w/ additional 0-10V Dimming Module Fully potted for moisture resistance and thermal Wet Listed Class 2 CSA Listed LED Power Supply (CSA 2108, 1838 ) 5 year warranty and Average 90% Efficiency
Features
© 2015, Q-Tran Inc. 155 Hill St. Milford, CT 06460. All rights reserved - P: 203-367-8777 - F: 203-367-8771 - E: [email protected] - www.q-tran.com
Each 12V QOM-ELED unit up to 1-3 60w or 1-3 100w.
Each 24V QOM-ELED unit has one to three 100W (200W,300W) Drivers.
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Max Outputpower (W)
Output Voltage (V)
OperatingTemp. range ( F)
Max Inputpower (W)
Weight (lbs) IP RatingOutput Current
(A)Input Current (A)
60 12 5.04.1
5.04.124100
60100
-40 ~140 F IP 66 0.3/135 -40 ~140 F
UL Class 2E220165
7310_S-000 3426-32
Primary Voltage - Universal Secondary Voltage 12 / 24VDC
Dimmer, If use, Must be Electronic Low Voltage Dimmer
QOM-eLED
Electrical Specifications
© 2015, Q-Tran Inc. 155 Hill St. Milford, CT 06460. All rights reserved - P: 203-367-8777 - F: 203-367-8771 - E: [email protected] - www.q-tran.com
QOM-eLED Design Guide & Installation Instructions
The main secondary wiring is intended for shallow burial - less than 6 inches (152mm) - unless wiring provided is intended for direct burial.
* To order additional lengths of wire for connection in the secondary Please call Factory for availability.
Do not use an extension cord when the power unit is cordconnected. Outdoor power units should be connected to a GFCI protected flush type cover plate receptaclemarked "Wet Location" while in use.
Note :
Risk of Electric Shock. Install power unit 5 feet (1.5 m) or more from a pool, spa, or fountain when the power unit is power-supply cord connected. Where the power unit is installed (a) indoors within 10 feet (3.0 m) of a pool, spa, or fountain or (b) outdoors, connect power unit to a receptacle protected by a GFCI.
Risk of Electric Shock. Install power unit 5 feet (1.5 m) or more from a pool or spa and 10 feet (3.05 m) or more from a fountain when the power unit is conduit-connected.Where the power unit is installed within 10 feet (3.05 m) of a pool or spa, connect power unit to a GFCI protected branch circuit.
Surface Wall Mount
Pole Mount
Mounting
1.77”
3.32”
1.57”
1/4” Rod Thru Hole
3/8” Rod Thru Hole
3.12”