qd-416

56
DAKSHIN HARYANA BIJLI VITRAN NIGAM NOTICE INVITING TENDER NO.320/DH/MM DATED: 25/10/2007 Sealed tenders from the bidders are invited in two parts in triplicate on the prescribed (Tender Document) Proforma’s for fixing the Rate Contract for the supply of following material. The Rate Contract shall be valid for one year from the date of award. a) Name of Item with Qty.:- Tend -er Enq- uiry No. Name of the item Total Qty. ( Nos.) QD- 416 Single Phase whole current static energy meters Class-I accuracy as per IEC-1036/ ISS-13779/CBIP -88 specification with upto date amendments and Nigam’s Specification of Rating 10-60 A with communication & upgrading facility UHBVN= 1,50,000 Nos. DHBVN= 2,50,000 Nos. Total = 4,00,000 Nos. QD- 417 Three Phase 4-wire whole current static energy meters Class-I accuracy as per IEC-1036/ ISS-13779/CBIP -88 specification with upto date amendments and Nigam’s Specification of Rating 10-60 A with communication & upgrading facility UHBVN = 75,000 Nos. DHBVN = 75,000 Nos. Total = 1,50,000 Nos. b) Being Rate Contract, the quantity can increase/decrease up to any extent. c) Amount of Earnest Money to be deposited = Rs.2.5 Lacs. each d) Cost of tender document:- Rs. 4,000.00 each. e) Last date of sale of Tenders upto 5.00 PM:- 27.11.2007. f) Due date of acceptance of Tenders (in the office of AGM/HR/MM,DHBVN, Hisar upto 1.00 PM:- 28.11.2007 g) Due date of opening of Part-I Tenders at 3.00 PM:- 28.11.2007 h) Tender documents and the other information can be had from Customer Care Center,33KV S/Stn,Raj Garh Road, DHBVN , Hisar during working hours on any working day up to the last date of sale of tender documents on payment of cost of tender, as mentioned, which is not refundable. The cost of Tender documents should be remitted by Demand Draft in favour of A.G.M./Cash, Dakshin Haryana Bijli Vitran Nigam,Hisar. i) The tenders of only those firms will be entertained who purchased copy of tender documents from CCC,DHBVN, Hisar and downloaded from Website of DHBVN, Hisar. j) The pre-bid meeting with the firms will be held on 19.11.07 at 11.00 A.M. k) The post Bid technical deviation meeting will be held on 11.12.2007 at 11.00AM. The interested Bidders shall have the Pre Qualification Requirements mentioned in annexure-A of the NIT and on the Nigam’s Website www.dhbvn.com . The detailed NIT is available on Nigam’s web site www.dhbvn.com. General Manager/MM For CGM./MM,DHBVN, Hisar.

Transcript of qd-416

Page 1: qd-416

DAKSHIN HARYANA BIJLI VITRAN NIGAM

NOTICE INVITING TENDER NO.320/DH/MM DATED: 25/10/2007

Sealed tenders from the bidders are invited in two parts in triplicate on the prescribed (Tender Document) Proforma’s for fixing the Rate Contract for the supply of following material. The Rate Contract shall be valid for one year from the date of award. a) Name of Item with Qty.:-

Tend-er Enq-uiry No.

Name of the item Total Qty. ( Nos.)

QD-416

Single Phase whole current static energy meters Class-I accuracy as per IEC-1036/ ISS-13779/CBIP -88 specification with upto date amendments and Nigam’s Specification of Rating 10-60 A with communication & upgrading facility

UHBVN= 1,50,000 Nos. DHBVN= 2,50,000 Nos. Total = 4,00,000 Nos.

QD-417

Three Phase 4-wire whole current static energy meters Class-I accuracy as per IEC-1036/ ISS-13779/CBIP -88 specification with upto date amendments and Nigam’s Specification of Rating 10-60 A with communication & upgrading facility

UHBVN = 75,000 Nos. DHBVN = 75,000 Nos. Total = 1,50,000 Nos.

b) Being Rate Contract, the quantity can increase/decrease up to any extent. c) Amount of Earnest Money to be deposited = Rs.2.5 Lacs. each d) Cost of tender document:- Rs. 4,000.00 each. e) Last date of sale of Tenders upto 5.00 PM:- 27.11.2007. f) Due date of acceptance of Tenders (in the office of AGM/HR/MM,DHBVN, Hisar

upto 1.00 PM:- 28.11.2007 g) Due date of opening of Part-I Tenders at 3.00 PM:- 28.11.2007 h) Tender documents and the other information can be had from Customer Care

Center,33KV S/Stn,Raj Garh Road, DHBVN , Hisar during working hours on any working day up to the last date of sale of tender documents on payment of cost of tender, as mentioned, which is not refundable. The cost of Tender documents should be remitted by Demand Draft in favour of A.G.M./Cash, Dakshin Haryana Bijli Vitran Nigam,Hisar.

i) The tenders of only those firms will be entertained who purchased copy of tender documents from CCC,DHBVN, Hisar and downloaded from Website of DHBVN, Hisar.

j) The pre-bid meeting with the firms will be held on 19.11.07 at 11.00 A.M. k) The post Bid technical deviation meeting will be held on 11.12.2007 at

11.00AM. The interested Bidders shall have the Pre Qualification Requirements mentioned in annexure-A of the NIT and on the Nigam’s Website www.dhbvn.com. The detailed NIT is available on Nigam’s web site www.dhbvn.com.

General Manager/MM For CGM./MM,DHBVN, Hisar.

Page 2: qd-416

Annexure-A Pre-qualification Conditions for the supply of Single Phase Static Meters of rating 10-60A with communication & upgrading facility. 1. Bid should be submitted in Two Parts, Part-I as Technical & Commercial and Part-II

as Price Bid. 2. The meter shall comply with the relevant standards of Bureau of Indian

Standards(BIS). If BIS Standards are not available for a particular equipment or material, the relevant British Standards(BS), International Electro-technical Commission (IEC) Standards, or any other equivalent Standard shall be followed.

Provided that whenever an international Standard or IEC Standard is followed,

necessary corrections or modifications shall be made for nominal system frequency, nominal system voltage, ambient temperature, humidity and other conditions prevailing in India before actual adoption of the said Standard.

3. Type Test Certificates should not be more than 3 years old on the date of opening of

tender part-I, Type Test Certificates should be supplied as part of the bid as per Nigam Technical Specification and as per latest ISS/CBIP/IEC Standards with latest revision.

4 Minimum annual average turn over ( MAAT) of the bidder for best three accounting

years out of last 5 accounting years of the bidder as on the date of opening of tender part-I should be at least Rs.200.00 Crores. Other income shall not be considered for arriving at annual turn over. Bidding in joint venture and separate bid of bidder having more than one business premises shall be considered in-eligible.

5 Past Performance of the firm with Nigam/Other Power Utility should be satisfactory

both in quality and adhering to the delivery schedule. 6. Damage Rate within warranty period should not be more than 10%.

a) The firm should have supplied 80% of the ordered quantity in contractual delivery period in the last purchase order.

b) The bidder shall have liquid assets (LA) and/OR evidence of access to or

availability of credit facility of not less than 25 Crores. 7. Minimum quantity to be quoted 50% of the NIT. 8. Only those bidders who have not been blacklisted by any State/Central Govt. OR

any Govt. Owned Power Utility shall be entitled to submit the tenders. The firm shall submit an affidavit of non-blacklisting on the non-judicial stamp of the appropriate value duly attested by Notary public.

Page 3: qd-416

DAKSHIN HARYANA BIJLI VITRAN NIGAM.

INSTRUCTION TO THE TENDERERS FOR NIT NO.320/DH/MM DT. 25 .10.2007 FOR THE SUPPLY OF SINGLE PHASE STATIC METERS of rating 10-60A with commu8nication & upgrading facility 0.5S ACCURACY CAPACITY -/5A.

Offer are invited from Manufacturers only for fixing of Rate Contract for the supply of Single Phase Static Meters of rating 10-60A with communication & upgrading facility ,Class 1 Accuracy as per following terms and conditions:-

1. The tender form, conditions of the contract including specifications and other information can be had from Customer Care Centre, 33KV S/Stn.,Raj Garh Road,DHBVN,Hisar on any working day during working hours upto the last date of Sale of tender documents on payment of prescribed fee which is not refundable. The cost of tender documents should be submitted in the form of Demand Draft/in favour of AGM/Cash, DHBVN, Hisar or by cash payment at the cash counter of DHBVN, Vidyut Nagar, Hisar. The tenders from only those firms will be entertained who purchase a copy of tender documents OR downloaded from the Nigam’s website alongwith receipt of tender cost.

2. The tender shall be submitted in two parts. Part-1(one) shall consist of earnest money, technical specification and general terms and conditions. Part-II shall consist of price bid only. Both Part-I and Part-II shall be submitted duly signed in sealed separate envelops and superscribed as Part-I and Part-II tender. Both these envelops should be sealed in another envelope. Tender enquiry No. & Date , Date of opening & detail of earnest money be mentioned on this envelope.

3. Detailed procedure for depositing Earnest Money, order preference to Haryana firms, delivery schedule and other terms and conditions are contained in Schedule-'B', 'C' and 'D of tender documents.

4. Tenders without prescribed earnest money or such tenders where reference to deposit of earnest money is not made on the envelope, will not be considered. PEMD already deposited by any tenderer with any other Power Utility i.e. UHBVN/HVPN/GENCO/DHBVN shall not be considered.

5. The tenders should remain valid for a period of 120 days from the date of opening of Part-II i.e. price bid. In case the validity is not mentioned or validity is less than 120 days from the date of opening of price bid such tenders will not be accepted.

6. The purchaser reserves the right to reject any or all the tenders received without assigning any reason.

7. The firms are required to quote only FIRM prices on FOR Destination basis any where in Haryana indicating Freight and insurance charges, Ex-works price, Excise Duty, Sale Tax or any other charges separately.

8. Tenders received after due date and time of acceptance irrespective of date of dispatch will not be entertained.

9. The tenderers shall give details of their Immovable Property i.e. Land, Building, Machinery etc. along with their exact location and ownership proof of the properties along with the tenders.

10. Clauses of the tender documents which have been approved and substituted by the amended clauses and pasted in the documents must be signed by the tenderers Technical Specification approved by the Nigam should be supplied with the tender shall be supplied after signing on each page of Specification.

11. Tenders must bear signatures of the person authorized as per constitution and composition of the firm Legal Power of Attorney in favour of signatory must be attached with the tender itself.

Page 4: qd-416

12. The addition to the type tests mentioned in Pre Qualification Conditions (Annexure-A)following tests as per Nigam's Technical Specification/ ISS-13779/CBIP Report-88 and latest amendment from recognized Govt. test house shall also be got done by the bidder on offered meters of required capacity.

i) Tamper and fraud protection test. ii) Electro-magnetic compatibility and D.C. immunity Test.

iii) Effect of magnetic field of external origin. The bidders will be required to submit the above test reports to the office of

Chief General Manager (MM), DHBVNL, Vidyut Nagar, Hisar up to the date of post Bid technical deviation meeting.

13. Deviations from Nigam's Technical Specification, if any, shall be specially mentioned in the tender.

14. The tenderer/bidder shall make a declaration on the relevant tender/documents that it has not been blacklisted by any State/Government Agency and that it shall be liable for the consequences of wrong declaration.

15. Memorandum of article and memorandum of association and power of attorney in respect of the person signing tender documents be also incorporated alongwith tenders.

16. Tenderer shall not submit their offer in any ambiguous free wordings failing which DHBVN’s interpretation will be final.

17. Tenderer must carefully study the technical specifications and general terms and conditions before preparation of tender.

18. The tenderer revising their offer or withdrawing the same within the validity period after opening of the tenders are liable to be ignored/black listed and EMD forfeited in such cases.

19. Complete technical details, test certificates, catalogues and drawings etc. must be supplied along with the tender.

20. Tendered quantity can be increased/ decreased up to any extent without assigning any reason.

21. The purchaser shall have the right to get the Meters functioning /plastic used in Meter Base & Cover tested from any Govt. Laboratory as per Nigam Specification. The payment will only be released on satisfactory report of testing agency and consequently or otherwise no interest on due payments would be payable.

General Manager/MM,

For CGM./MM,DHBVN, Hisar

Page 5: qd-416

DAKSHIN HARYANA BIJLI VITRAN NIGAM LIMITED Annexure ‘B’ to Schedule – ‘D’

DELIVERY SCHEDULE

Sr. No.

Tender Enquiry No.

Name of Item

Ten-tative Qty. (in Nos.)

Name of Consignee

Destination of Consign-ment

Delivery

1 QD-416

Single Phase Static Meters accuracy class-1 of rating 10-60A as per relevant ISS & Nigam Technical Specification.

UHBVN=150000 Nos.+ DHBVN= 250000 Nos. Total= 400000 Nos.

Anywhere in Haryana

Anywhere in Haryana

10% tentative qty. of rate contract should be supplied with in 45 days from the date of receipt of initial order to be placed by CGM/MM, DHBVN/UHBVN and balance in 10 equal monthly lots as per orders to be placed by the CGM/GMs of both Nigams as per the requirement.

- SIGNATURE OF SUPPLIER

Page 6: qd-416

SCHEDULE ‘B’

(General Instructions to Tenderers) The following instructions must be carefully observed by all tenderers. Offers/ Tenders not strictly in accordance with these instructions will be liable to rejection. 1. The tender must be on the prescribed tender form and complete in all respects. 2. Tenders should be submitted in triplicate, per Regd. Post both copies should be separately tagged and clearly marked as ‘Original’, ‘Duplicate’ AND Triplicate Offers not received in triplicate may be ignored. 3. Offers/Tenders should positively reach before the last date prescribed for their receipt those received late will not be considered. 4. The ‘Tender form alongwith the, ‘Terms and Conditions of Contract’ and its Annexure ‘A’ and ‘B’ should be returned in triplicate with each page there of signed by the tenderer and with all the required particulars and rates filled in at appropriate places. 5. Offers/Tenders should be enclosed in double-covers. Both the inner and the outer covers should be sealed and superscribed with the Tender/offer No. together with the date on which the offer/tender is due and the items of material covered. 6. The offers/tenders will be opened on the date and time prescribed in the Notice Inviting Tenders. In case the date of opening falls on a holiday or a holiday is subsequently declared on that date, the tenders will be opened on next working day following the holiday. 7. Material offered should be strictly according to the specifications laid down in Annexure ‘A’ to the Terms and conditions of the contract. Unless a deviation item the specifications given in Annexure ‘A’ is pointed out by the tenderer specifically, it will be presumed that Offer/tender conforms to the specifications as laid down in Annexure ‘A’. 8. The prices should be for supply of the material in safe condition F.O.R. Destination or Ex-works/suppliers premises, the location of which should be clearly specified, failing which the offer/tender may be ignored. The rates of ED, VAT/CST, freight and transit insurance charges etc. may also be quoted separately. 9. All Tender/offers will be regarded as constituting an offer or offers open to acceptance in whole or in part until the last date of validity as prescribed in the notice inviting enders or as indicated by the tenderer in his tender/offer, whichever be later. 10. The offer/tender should be typed or written in ink, offer /tender written in pencil shall be ignored. 11. The price must be quoted in Indian Rupees and any mistake in calculating the rupee price will not justify the claim for increase in prices.

Page 7: qd-416

12. Tenderer should specifically mention the period of validity of offer/tender. The period of the validity should not be less than that specified in the notice inviting tenders. 13. The tender shall not be opened at all in case the validity is not indicated on the envelope containing tender. 14. The time and date of delivery of the material stipulated in Annexure ‘D’ to the terms and conditions of the contract/ purchase order shall be deemed to be the essence of the contract and the delivery must be completed not later than the date or dates specified therein. 15. The offer/tenders not accompanied with earnest money in one of the following forms drawn or executed in favour of the purchaser, shall not be accepted. (a) Cash Deposit. (b) Bank Draft. (c) EMD in the form of Bank Guarantee in favour of the Nigam shall also be accepted if the estimated value of the material/contract is more than 5 Crores. (d) In any other form specifically approved by the purchaser. As soon as the tender has been decided upon and the order placed on the selected supplier / contractor(s), the earnest money deposit of the unsuccessful tenderers (except L-1 and L-2 bidders) shall be released forthwith by the purchasing department without waiting for any formal application from the unsuccessful tenderers. The purchasing department shall ensure that the refund of earnest money deposit is allowed within two weeks of the decision on the NIT. The EMD of L-1 and L-2 shall be released after submission of performance Bank Guarantee by the successful bidder i.e. L-1. The performance guarantee shall remain valid for 90 days after the expiry of warranty period. 16. The Bank charges, if any, will be to the account of the tenderer. 17. No claims against the Nigam either in respect of interest if any due on the Security deposit/Earnest money or its depreciation in value shall be admitted. 18. The quantities specified in the NIT can be varied upto any extent at the sole discretion of the Nigam without assigning any reason. 19. Telegraphic tender shall not be considered. 20. The purchaser reserves the right to reject to any or all tenders received without assigning any reason. 21. The enquiry No. and the due date should be written clearly and distinctly on the sealed cover containing the quotation. 22. The validity of the quotation should not be less than 90 days (in case bid is invited in one part) and120 days from the last date of opening of price bid (Part-II). In case the Bid is invited in two parts. 22(a) Amendments/Modifications to Tenders The tenderer, after submitting its tender, is permitted to submit alterations/modifications to its tender so long such alterations/modifications are received duly sealed and marked like original tender, upto the date & time of

Page 8: qd-416

receipt of tender. Any amendment/modification received after the prescribed date & time of receipt of tenders are not to be considered and any withdrawl of the offer shall not be permitted. However, the firm may modify their offer before opening of bid, but the Nigam will consider the lowest one. 23. The tenders quotation should be addressed to the Chief General Manager/MM, DHBVNL Vidyut Nagar, Hisar where these shall be opened on prescribed date and time indicated in the NIT. 24. Any party while submitting tenders to the Nigam would submit (a) the earnest money and (b) the quotations/tender in two separate sealed covers. The envelope containing the earnest money should a part from mentioning the name of the party submitting the tender quotation and the tender enquiry number to which it relates should be clearly inscribed over with the Word Earnest Money amounting to Rs._______________ enclosed. The second envelop apart from giving similar relevant details regarding the tender enquiry number and the name of the party should be clearly inscribed over with the words contains tender/quotation prices only. Each of these envelopes would be sealed and signed by the party submitting the tender, and the envelopes placed in bigger sealed envelope. This outer, cover would also contain reference to the tender, enquiry as also the name and signature of the party submitting the tender. 25. However, the following tenders shall be exempted from the deposit of earnest money. (i) Wholly Govt. of India owned undertakings. (i) Wholly State owned undertakings of Haryana. 26. Only such a tender shall be considered “Valid tender” where the tenderer has in accordance with the above regulation remitted the requisite amount or earnest money. 27. Separate tender must be submitted against each enquiry. 28. The Tenderer must clearly state whether they are a small scale/Large scale industries and the rate of excise duty as applicable to them must be stated in tender. 29. Tenders not submitted on prescribed form will be liable to be rejected. 30. “The post tender offers or communications received from the supplier/contractors etc. which erect the quoted and equivalent rates there by changing the merit position of the tender shall not be entertained”. 31. The purchase contract will come into existence on the date the purchaser posts acceptance to the supplier offer either through telegram, by a letter through post /through fax. The date of posting the telegram or letter will be the date of agreement and the contractual obligation of the supplier will commence from that very date. The supplier will have no right to revoke his offer after the purchaser has posted his acceptance in the aforesaid manner. 32. The tenderer should indicate separately ex-work prices, Excise Duty Sales Tax freight charges, transit insurance charges or any other charges for purpose of assessing the total per unit price.

Page 9: qd-416

33. The Red Slip (Enclosed) duly filled in properly & complete in all respects, must be pasted on the outer most envelope of the tender. 34. In the event of a firm not favoring the delivery commitment of the previous contracts, this fact will weigh against the firm tendering against a subsequent enquiry and be treated as disability. Before issue of the letter of intent or of placing the order, the previous order should be fully discharged or a reliable under taking should be given that it would be done within a reasonable period and within a scope of the previous contract, if the firm decline to give this undertaking it would be considered ineligible for competing against any subsequent or and the order would automatically pass on the next lower firm. 35. The bidder will furnish Type Test Results. The type tests must have been conducted on the material offered as per the relevant IS in recognized laboratory as per the latest revision of the Technical Specification and the date of Type tests will not be later than 3 years. The Bids received without type test reports will be treated as Non-Responsive. 36. The prices charged for the stores supplied under the Contract by the Contractor shall no event exceed the lowest price at which the Contractor sells the Stores or offer to sell stores of identical description to any person(s)/organization(s) including the Purchaser or any Department of the Central Government or any Department of a State Government or any statutory undertaking of the Central or a State Government, as the case may be, during the period till performance of all Supply orders placed during the currency of Contract is completed. 37. In the case of distribution transformer, if damage within the warrantee period, the same should be replaced by the supplying firm free of cost. The supplier shall supply a new transformer and the damaged transformer will be taken back by him and pending this the full cost of damaged transformer will be recovered/deducted from the outstanding bills by the paying authority and it will be released after the damaged transformer is replaced by new one. 38. ARITHMETICAL ERRORS In case of any inconsistency in the price furnished, the purchaser shall be entitled to consider the lowest prices for the purpose of evaluation and award of contract. All arithmetical errors will be rectified on the basis of the unit price or total price ( in figures and in words) whichever is more beneficial to the purchaser. 39. A copy of the constitutions of the Company/firm or Balance Sheet, Power of Attorney in the name of person who signs the tender documents shall be submitted alongwith tender documents. 40. The bidder shall accept all the clauses of NIT failing which their bid/tender is liable to be rejected. 41. Purchase preference : Purchase preference may be allowed upto 50% of the requirement to the industrial units located in Haryana on the lowest quoted/ agreed rates provided the tendering firm claim the purchase preference in their tender and submit the registration certificate and the valid purchase preference certificate issued by Industries Deptt. Alongwith their tender and submit an affidavit that their sales office for the purpose of billing is bases in Haryana and all the billings are/ will be raised from Haryana only. Provided purchase preference of 50% of the quantity shall be allowed only to those

Page 10: qd-416

industrial units in Haryana who qualify among 3 lowest valid firms and agrees to accept the lowest (L1) tenderer rates and where more than one tenderer having their industries in Haryana agreed to the lowest rates, the 50% quantity covered under purchase preference, may be divided between them on proportionate basis keeping in view the quantity/ delivery period quoted by them. 42. Blacklisting of the Firms: As the purchase order becomes a valid contract between the purchaser and supplier on the date of its issue, no further changes in the terms and conditions thereof are permissible and any request received in this regard from the supplier should be summarily rejected, making it clear to supply the goods strictly in accordance with the terms and conditions of the contract. It should be noted that such a liability can be enforced on the supplier only if the purchase order does not contain any term or condition contrary to what had been quoted in the supplier’s tender. Once this is ensured, any attempt by the supplier to back out of his commitment should be taken a serious and his earnest money deposited be forfeited forthwith, without prejudice to any further legal remedies open to the Nigam under the relevant laws. Where necessary, the case of supplier illegally backing out of the commitment, should also be put up to the Whole Time Directors for consideration and to decide for black-listing of the firm and damages, if any, to be recovered. 43. On the day the purchaser convey acceptance to the supplier’s offer either through telegram/fax or by a letter, the date of telegram/fax or letter will be the date of agreement and the contractual obligation of the supplier will commence from that very date. The supplier will have no right to revoke his offer after the acceptance of purchaser. Place : Name & Full address of tenderer Date :

Page 11: qd-416

SCHEDULE ‘C’

(Referred to in-Regulation 7) DAKSHIN HARYANA BIJLI VITRAN NIGAM TENDER FORM

From __________________________, __________________________, __________________________, To __________________________, __________________________, __________________________, Offer No.______________ Dated__________2007 Subject : Submission of tender against Notice Inviting Tender No.________ dated _____________ of Dakshin Haryana Bijli Vitran Nigam. Dear Sir, With reference to your above mentioned notice inviting tender, I/We hereby offer to supply genuine goods and materials (quantity and rates of the goods and material are described in the attached terms and conditions) and shall execute the work truly and faithfully within the time specified and set forth in the attached terms and conditions. The goods and materials to be supplied will be of the quality and answerable in every respect with this tender. I/We shall be responsible for all complaints as regards the quality of material and in case of dispute the decision of the Nigam will be final and binding on me/us. A Bank Draft No._________________ for the prescribed amount of Rs.________Rupees_____________________________) drawn in favour of DGM/F&A/MM, DHBVNL, Hisar is enclosed, as earnest money as desired. I fully understand that in the event of my/our tender being accepted this earnest money shall be retained by you as security deposit payable by me/us for the faithful and satisfactory execution of the contract. (Delete whichever not applicable)

Page 12: qd-416

I further understand that the B.G. equivalent to the value of 10% of the contract value in lieu of retention money shall be submitted by me till the faithful execution of the contract including the period for which the warranty remains applicable. 1. I/We shall have no claim to the refund of the earnest money prescribed against this tender in the event of my/our non-compliance of the purchase order provided such order is placed within the period of validity of my/our tender as indicated in paragraph 4 below. I further understand that my earnest money will stand forfeited even if I withdraw my tender at any stage during the currency of the period of validity. 2. My/our tender shall remain valid for a period of _________ days from the last date prescribed for submission of the tenders against the NIT No._______________ dated ____________. 3. My/our tender alongwith the terms and conditions with the relevant columns and annexures duly filled in under my/our attestation and with each page of the tender papers (including the enclosed terms and conditions signed by me/us, (in the capacity of sole owner/general or special attorney, in proof of which power of attorney is attached) is submitted for your favourable consideration. 4. I/We have read the enclosed terms and conditions carefully and have signed thesame in token of their absolute and unqualified acceptance. My/our tender constitutes a firm offer under the Indian Contract Act 1872 and is open to an acceptance in whole or in parts. My/our offer, if accepted on the attached terms and conditions will constitute a legally binding contract and shall operate as a contract as defined in the Indian Contract Act 1872 and the Indian sale of goods Act 1930. Thanking you.

Yours faithfully, Place Dated Name & Full Address of Tenderers

Page 13: qd-416

NIT No.___________________ Enquiry No.________________

SCHEDULE ‘D-I’ (Referred to in-Regulation 7)

DAKSHIN HARYANA BIJLI VITRAN NIGAM TERMS AND CONDITIONS FOR PROCUREMENT OF

EQUIPMENT STORES AND OTHER MATERIAL UNDER THE RATE CONTRACT

In construction of the terms and conditions of the contract, the following words shall have the meaning herein assigned to them, unless the subject or context otherwise requires: (a) The “PURCHASER” shall mean the DHBVNL or its authorized agent and shall include its Successors in office, and assigns. (b) The “SUPPLIER” shall mean M/s ___________________________________ and shall include the supplier’s legal representatives, successors, and assigns. (c) “MANUFACTURERS: shall mean M/s _______________________________ and shall include their legal representatives, successors, and assigns. (d) “MATERIAL” all the materials to be supplied by the supplier under the contract as per clause of material specifications, price etc. (e) ‘SPECIFICATION’ shall mean and include the specifications as detailed in the Annexure attached herewith and Drawings attached thereto as well as samples and patterns, (if any). (f) The ‘SITE’ shall mean and include the lands and buildings over/under/upon and in which the materials are to be installed and used in accordance with the terms and conditions. (g) ‘PLACE OF DELIVERY’ shall mean the place of delivery at which the supplier is responsible to deliver the material at the contract price as specified in the clause “Material- Specification: Price etc. (h) ‘COMMERCIAL USE’ shall mean the use to which the material can commercially be put. (i) ‘MONTH’ shall mean a calendar month. (j) ‘THE TERMS’ F.A.S., F.O.R., F.O.B., C.I.F. and other shipping/ despatch terms as used herein, shall have meaning in accordance with their uses in India. (k) ‘WORK’ shall mean and include supply of all the materials, plants and equipment and rendering of other services by the supplier under this contract. (l) ‘ACT’ shall mean the Companies Act 1956 and shall include any statutory amendments,modifications or re-enactment thereof for the time being enforce. (m) ‘THE NIGAM’ shall mean the DAKSHIN HARYANA BIJLI VITRAN NIGAM as incorporated under Companies Act 1956 and shall include its successors and assigns.

Page 14: qd-416

(n) ‘MANAGING DIRECTOR’ shall mean the Managing Director of the NIGAM duly appointed by the Govt. (o) ‘CONSIGNEE’ shall mean the officer to whom the materials is required to be dispatched or the person specified in the purchase order. (p) ‘CONTRACT’ shall mean the Notice Inviting Tender. Instructions for tenderers, Tender Forms, terms and conditions of contract with their annexures and purchase order/ acceptance of offer/Tender. (q) ‘DRAWING’ shall mean the drawing/drawings annexed to the specification (if any) or as approved by the purchaser. (r) ‘PURCHASE AUTHORITY’ shall mean the officer signing the acceptance of tender and shall include any officer who has authority to execute the relevant contract on behalf of the purchaser. (s) ‘PURCHASE ORDER’ shall mean an order of supply of material including the acceptance of the tender. (t) ‘ANNEXURE’ shall mean the Annexure to the terms and conditions. (u) ‘ACCEPTANCE OF TENDER’ shall mean the letter or memorandum communicating to the supplier the acceptance of his offer (Tender) and shall include advance acceptance of his offer. (v) ‘TEST’ shall mean such test as is prescribed by the Indian Standards Institution or by the Nigam and/or considered necessary by the authorized agents of the purchaser, whether conducted/performed or made by him or any other agency acting under his direction. (w) ‘DELIVERY’ shall be deemed to take place on delivery of the material in accordance with the terms and conditions of the Contract after test and inspection by the purchaser or his authorized agent, to the consignee. (x) D.G.S & D shall mean the Director General of Supplies and Disposals, Government of India. (y) DS&D shall mean the Director Supply & Disposal, Haryana. (z) Direct Demand Officer shall mean the officer authorized by the Chief Engineer/MM (Nodal Agency) for placing supply order as per their office requirement under the Rate Contract. 2. PARTIES. The parties to the contract are the supplier and the purchaser, Legal address of the parties to the Contract is under: Supplier M/s ___________________________________________________ __________________________________________________________ Purchaser: Dakshin Haryana Bijli Vitran Nigam (Hisar) For all purposes of the contract including the arbitration thereunder, the address of the supplier mentioned above, shall be the address to which all communications addressed to the supplier shall be sent, unless the supplier has notified a change by a separate letter containing no other communication and sent by a Registered Post(Acknowledgement Due) to the purchaser. The supplier shall be solely responsible for the consequences of an omission to notify the change of address in the manner aforesaid.

Page 15: qd-416

3. AUTHORITY OF THE PERSON SIGNING THE CONTRACT ON BEHALF OF THE SUPPLIER. The person who has signed these Tender papers (including the terms and conditions) has got authority to sign on behalf of the supplier. It is discovered at any time that the person so signing had no authority to do so, the purchaser without prejudice to any other right or remedy available to him may, cancel the contract and make a purchase of the material at the risk and cost of such person and hold such person liable to the purchaser for all costs and damages arising from the cancellation of the contract including any loss which the purchaser may sustain on account of such purchase. 4. RESPONSIBILITY OF THE SUPPLIER FOR EXECUTING THE CONTRACT. (I) RISK IN MATERIAL The supplier shall execute the contract in all respects in accordance with these terms and conditions. The material and every constitute part thereof, whether in possession or control of the supplier, his agents or servants or a Carrier or in the joint possession of the supplier, his agents, servants and the purchaser, shall remain in every respect at the risk of supplier until its actual delivery to the consignee at the stipulated place or destination. The supplier shall be responsible for all loss, destruction, damage or deterioration of or to the material from any Cause whatsoever while the material after test and inspection is awaiting dispatch or delivery in course of transit from the supplier to the consignee. The supplier shall alone be entitled and responsible to make claims against the carrier in respect of non delivery, mis-delivery, short delivery, loss destruction, damage or of the deterioration material entrusted to such carrier by the supplier for transmission to the consignee. (II) CONSIGNEE’S RIGHT OF REJECTION Notwithstanding any approval which the purchaser may have given in respect of the material, it shall be lawful for the consignee to reject the material or any part thereof on behalf of the purchaser within a reasonable time after actual delivery thereof to him at the place or destination specified in Annexure ‘B’ if the material or any part or portion thereof is not in all respects in conformity with the terms and conditions of the contract whether on account of any loss, deterioration or damage before despatch or delivery or during transit or otherwise howsoever. The provision contained in clause 14 (VI) below relating to the removal of material rejected by the purchaser or his authorised agent shall, mutatis mutandis, apply to material rejected by the consignee as herein provided. (III) SUBLETTING AND ASSIGNEMENT: The supplier shall not save with the previous consent in writing of the purchaser sublet transfer or assign the contract or any part thereof or interest therein or behalf or advantage thereof any manner whatsoever. 5. ASSISTANCE TO SUPPLIER The supplier shall be solely responsible to procure any raw material, license or permit required for the fulfillment of the contract. Any assistance for the procurement or attempt to tender assistance in the matter aforesaid, shall not be construed or constitute any promise, undertaking or assurance on the part of the

Page 16: qd-416

purchaser regarding the procurement of the same of effect any variation in the rights and liabilities of the parties under the contract. 6. SECURITY DEPOSIT i) The earnest money furnished by the successful tenderer’s to whom the purchase order/ contract is allotted shall be refunded within 7 days from the receipt of performance guarantee as per contract by the accounts wing/DDO on intimation to the purchasing authority for making necessary entries in EMD register. The earnest money of lowest (L-2) shall be released after submission of performance Bank Guarantee by the successful bidder i.e. L-1. ii) The supplier agrees that they will submit BG equivalent to 5% or 10% , as the case may be, of contract value in lieu of retention money. iii) Security deposit shall be retained by the purchaser for the period valid for 90 days after the expiry of warranty period as per clause of ‘WARRANTY’. iv) No. claim of the supplier shall lie against the purchaser either in respect of interest or any depreciation in the value of security deposit. v) If, the supplier fails or neglects to observe or perform any of his obligations under this contract, it shall be lawful for the purchaser to forfeit either in whole or in part, in his absolute discretion, the security deposit furnished by the supplier. The forfeiture of security deposit shall be without prejudice to the right of the purchaser to recover any further amount of any liquidated and/or other damages, undue payment or overpayment made to the supplier under this Contract or any other contract. 6.A) Low rates)- To curb the tendency to quote low rates and execute the works unsatisfactorily, the quoted rates shall be compared with the estimated cost and shall be dealt with as follow:- a) If the quoted rate for a work is below 25% of the estimated rates, it will be rejected. b) If the quoted rate is between 10% and 25% below estimated rate, the contractor will remit performance guarantee equal to the difference between estimate Price and quoted price. This will be released after satisfactory completion of the work. 7. MATERIAL, SPECIFICATIONS, PRICES, ETC. (i) The supplier shall supply the following quantities of different items of material of the best quality, workmanship and strictly in accordance with the specifications and rates shown against each, unless any deviation in specification has been expressly pointed out in the purchase order. Sr. No.

Code No. of material Name of item Specification Rate Ex-works/ FOR Destination

(As detailed in Annexure attached hereto)

Provided that the quantity specified above can be increased or decreased up to 25% at the sole discretion of the purchaser. (ii) The above rates shall remain firm for the entire supply indicated above and subject to no variation in any circumstances whatsoever. The rates shown above

Page 17: qd-416

are inclusive of packing/forwarding charges/ Insurance charges/ Excise Duty/ Sales tax/ VAT etc. for respective destination. (iii) PERIODICAL ASSESSMENT OF RATE AND UNDERTAKING FOR PRICE FALL. (a) Periodical Assement of Rate: Since the rate Contract is for one year thus the rates as finalized will be assessed/verified by the Nodal Agency periodically. In case a downward trend in their market rates are observed. The Nigam shall have the right to review the rates time to time. Price Fall Clause: i) The prices charged for the material supplied under the rate contract by the firm shall in no way exceed the lowest price at which the firm sales the material to any person/organization including the purchaser or any other department of the Central Govt. or any Deptt. Of the State Govt. or any Statutory Undertaking of the Central or State Govt. as the case may be during the delivery period till performance of all supply orders placed during the currency of the rate contracts is completed. (ii) If at any time during the said period the firm reduces the rates of sales prices sells the contract or offer to sell such material to any person/Organization including the purchaser or any Deptt. Of Central Govt. of any Deptt. Of the State Govt. or any Statutory Undertaking of the Central or State Govt. as the case may be at price lower than the price chargeable under the rate contract, shall forthwith notify such reduction / sale or offer to sale to the Nigam and the price payable under the rate contract for the material supplied after the date of coming into force of such reduction or sale offer to sale, shall stand correspondingly reduced. iii) The firm shall furnish the following certificates to the concerned Consignee’s alongwith each bill against the rate contract:- “I/We certify that there has been no reduction in sale price of the material of description identical to the material supplied to Nigam under the rate contract herein and such the material has not been offered and sold by me/us to any person/ organization including the purchase of any Deptts. of the Central Govt., any Deptts. Of the State Govt., any statutory undertaking of the Central or State Govt. as the case may be upto the date of bill/date of completion of supplies against all supply orders placed during the currency of the rate contract at a prices lower than the prices charged to Nigam under the rate contract.” 8. SAMPLE The material will be supplied by the supplier strictly in accordance with the sample approved by the purchaser or his authorised agents, whose decision as to whether or not, the material conforms to the sample shall be final and binding on the supplier. 9. (I) DELIVERY The supplier shall deliver the material in accordance with the terms and conditions of the contract at the time/times and at the place/places and in the manner specified in the Annexure ‘B’ attached thereto. In case the due date of delivery in terms of delivery schedule falls on a holiday or holiday is subsequently declared on that date, the firm shall be required to complete the supply by the first working day falling next to the due date.

Page 18: qd-416

(ii) TIME FOR AND DATE OF DELIVERY; THE ESSENCE OF THE CONTRACT. The time for and the date of delivery of the material stipulated in the Annexure ‘B’ purchase order shall be the essence of the contract and delivery must be completed not later than the date(s) as specified in Annexure “B’/purchase order. (iii) NOTIFICATION OF DELIVERY:

Notification of delivery of dispatch in regard to each and every consignment shall be made to the purchaser and respective consignees. The supplier shall supply to consignee a packing account and full details of the contents of the package and delivery of material in order to enable the consignee to check the material on arrival at destination.

(iv) DAMAGES FOR DELAY IN DELIVERY: The delivery of material as per the Annexure “B” attached to the Terms and Conditions of Contract (Schedule ‘D’) shall be the essence of the contract between the supplier and the Nigam and the delivery of such consignment must accordingly be insisted upon the date it is due in terms thereof. As also stipulated under Regulation 16.6 no supplies/consignments received after the due date, on which they were actually due according to the terms of the purchase order, shall be accepted by the consignee except, with the approval of the purchasing authority. In case the purchasing authority decides to accept a delayed supply, the supplier shall be liable to pay penalty @ one half of one percent per week or part thereof up to 10 weeks and 1 per cent thereafter per week or part thereof of the value of the goods, so delayed, subject to a maximum of 10% of the total value of the delayed supplier. In case the delivery schedule provides lot wise delivery of material, lot wise penalty shall be imposed. (v) BLACKLISTING DUE TO HIGHER DAMAGED RATE: Those firms whose damage rate of energy meters (manufacturing defect)found more than one per cent will be blacklisted for the next three years and no business shall be undertaken with the firm during that period. (vi) PASSING OF A PROPERTY: Property in the material shall not pass to the purchaser unless and until the material has been delivered to the consignee, in accordance with the terms and conditions. (vii) TAKING OVER CERTIFICATES: The consignee (s) shall issue a taking over certificate after the material has been received at site (s), taken into possession, inspected, counted, measured and the supplier has supplied the copies of tests and inspection-certificate, if any, vide clause-14 “Test and Inspection”. 10 . FORCE MAJEURE: The supplier shall not be liable for any loss or damage due to delay in manufacture or delivery of the material for reason arising out of compliance with regulations, orders or instructions of Central/State Govt. Acts of God, acts of Civil and Military authorities, fires, floods, strikes, Lockouts, freight embargoes, war-risk, riots and civil commotion. Whenever the supplier is not in a position to supply the material within the delivery period and he wants extension in the due date (s) of delivery under this clause, he will request for such extension of the delivery period along with all necessary evidence, before the expiry of the scheduled date(s) of delivery. In no case, the delivery period shall be extended under this clause, in case the request is received after the due date of delivery has expired. Extension in the delivery period may be granted only for the period

Page 19: qd-416

for which the completion of the work is proved by the supplier to have been delayed for circumstances mentioned in this clause. In all such cases, the Nigam shall have the option to accept any portion of the balance material and cancel the order for the rest, provided, however, if any material had been manufactured exclusively for the purchaser under this contract prior to the commencement of the force majeure circumstances, it shall be accepted by the purchaser and secondly, the cancellation will be without any liability for damages on the part of the supplier. The decision of the purchaser in all matters under this clause shall be final and binding on the supplier. Non-availability of raw material or any other similar cause shall not be considered as a force majeure circumstance. 11 WARRANTY In case of Electronic Meters the supplier shall be made responsible to replace free of cost, with no transportation or insurance-cost to the Nigam, up to the destination, the whole or any part of the material which in normal and proper use proves defective in quality or workmanship, subject to the condition that the defect is noticed within 66 months from the date the material is received by the consignee or 60 months from the date of installation which ever period may expire earlier. The consignee or any other officer of the Nigam actually using the material will give prompt notice of each such defect to the supplier as well as the Purchasing authority and the Controller of Stores. The replacement shall be effected by the supplier within a reasonable time, but not, in any case, exceeding 45 days. The supplier shall also arrange to remove the defective supply within a reasonable period but not exceeding 45 days from the date of issue of the notice in respect thereof. Upon the firm failing to do so, the damages/defects may be got rectified by the Nigam and the cost adjusted from the firm’s pending dues and/or security deposit against this or any other contract in force and the balance left be got deposited good by the supplier. The Nigam may withheld the amount equal to cost of defective material. These provisions shall, also equally apply to the replaced material. In case, the material is again found to be defective within warranty period, it shall, also, have to be replaced similarly. 12 DRAWINGS: (a) The supplier will submit, in quadruplicate, to the Purchaser for his approval (within 15 days) immediately on receipt of his offer’s acceptance from the purchaser detailed dimensional drawings of the equipment to be supplied and other general arrangements of the work to be carried out and such other detailed drawings as may be reasonably necessary. Submission of incomplete drawing or any delay in submission of drawing beyond 15 days shall be towards to supplier account. (b) The drawing will be approved by the purchaser and returned to the supplier within one month from the date of their receipt. Any period beyond one month taken by the purchaser for the approval or otherwise of the contract drawings may be regarded by the Supplier as a ground for extension of time for completion of the work. (c) In case the firm requests for use of purchaser’s drawings, the same shall be provided by getting deposit of Rs.3000 per drawing.

Page 20: qd-416

13 MISTAKES IN DRAWINGS: The supplier will be responsible for and shall pay for alterations of the material or works due to any discrepancies, errors or omissions in the drawings or other particulars supplied by him whether such drawings or particulars have been approved by the purchaser or not. Mistakes in drawing will be set right by the Supplier after obtaining approval of the purchaser. 14 TESTS AND INSPECTION: The material shall be inspected and tested by the purchaser or his authorised agent before despatch unless dispensed within writing by the purchaser. The Supplier shall give to the purchaser at least 20 days advance notice for such inspection and test. Nigam intends to purchase only High Quality material. For this purpose sample from minimum 3 lots (if total lots are 3 or more than 3) of the material supplied should be sent to Sri Ram Test House/Govt. Approved Lab for Testing at Nigam’s Cost. Any lot shall be finally accepted only when the samples are passed by the Test House. In case sample fails, the entire lot shall be rejected which will have to be lifted back by the firm at its own cost. If the sample drawn from two or more lots are rejected by the Test House, the entire balance quantity shall be deemed to have been cancelled and the Nigam will affect the purchases for the balance quantity on the risk and cost of the supplier. For these reasons, the firm can also be blacklisted for future supplies. (i) FACILITIES FOR TESTS AND INSPECTION: The Supplier shall, at his own expense, afford to the Purchaser or his authorised agent, all reasonable facilities and such accommodation as may be necessary for such tests and inspection. The Purchaser or his authorised agent shall have full and free access at any time, during the execution of the contract to the supplier’s work for the purpose aforesaid, and he may require the Supplier to make arrangement for inspection of the material or any part thereof at his premises or at any other place specified by the Purchaser or his authorised agent. (ii) The Supplier shall provide, without any extra charges, all materials, tools labour and assistance of every kind which the Purchaser or his authorised agent may demand of him for any test and inspection. The purchaser or the authorised agent, shall in his sole judgement, be entitled to remove for tests and inspection any of the material to any premises other than his (Supplier’s) premises. (iii) LIABILITY FOR COSTS OF LABORATORY TEST: In the event of rejection of material or any part thereof by the purchaser or his authorized agent which is removed to the Laboratory or other place of test, the Supplier, on demand, shall pay to the Purchaser all costs incurred in such removal. (iv) METHOD OF TESTING: The Purchaser or his authorised agent shall have the right to put all the material or part thereof to such tests as he may think fir and proper. The supplier shall not be entitled to object on any ground whatsoever to the method of testing by the purchaser or his authorised agent. (v) The Supplier shall mark or permit the purchaser or his authorised agent to mark all the approved material with a recognised Purchaser’s mark. The material which cannot be so marked, shall, if so, required by the Purchaser or his

Page 21: qd-416

authorised agent, be packed in suitable packages or cases which shall be sealed and marked with such mark. (vi) REMOVAL OF REJECTED MATERIAL: If any material is rejected by the Purchaser or his authorised agent after tests and inspection or by the consignee, the material so rejected shall be removed from the premises of rejection by the supplier at his own cost. Such rejected material shall under all circumstances lie at the risk of the Supplier from the moment of such rejection; and if such material not removed by the Supplier within a period of 45 days, the Purchaser or his authorised Agent or consignee may dispose of such material in any way at the Supplier’s risk and cost and retain such portion of the proceeds as may be necessary to cover any expense incurred in connection with such disposal shall, also be entitled to recover handling and storage charges for the period during which the rejected material is not removed. (vii) CERTIFICATE OF TEST & INSPECTION When the test and inspection have been satisfactory carried out by the purchaser or his agent, the purchaser or his authorised agent shall issue a certificate to that effect and the material will then be dispatched by the Supplier according to despatch instructions of the Purchaser or his authorised agent vide Clause-19 Dispatch Instructions. (viii) POST RECEIPT INSPECTION: The material after receipt in the stores of the Nigam is liable to be inspected for its conformity to the specification by a representative of the Nigam in the presence of representative of the contractor/ supplier after one week registered notice to the supplier/ contractor. In case the firm fails to depute a representative in the specified date, the Nigam would be free to get the material checked in the absence of firms representative for which the firm would have no reason to protect at any stage and would be fully responsible of the outcome. On receipt of the advance notice from the supplier offering the material for inspection the purchasing authority will get the material inspected and issue of dispatch authorisation within 20 days. In case the Inspecting Officer finds on arrival at the supplier’s premises that the material was not ready for inspection and that the notice given by the supplier was infractuous, the expenditure incurred by the Nigam on arranging for such inspection will be debited to the firm’s account. Besides this a letter of warning shall be issued and it shall be counted towards their performance for all intents and purposes. The Contractor shall be responsible to pay penalty of Rs. 20,000/- for each occasion at which the fake inspection call has been made or the material is rejected during testing/inspection by the authorised agency/representative of the Nigam. This penalty would be in addition to the expenses incurred by the Nigam in deputing the Inspecting Officer, carrying out such inspection. (ix) TYPE TEST CONDITIONS: i) In case of new firms fresh type test may not be insisted upon, if the type test certificates produced is not more than 3 years old and related to a purchase/ supply to any of the utilities.

Page 22: qd-416

ii) If the type test is conducted on a proto-type and the same has not been witnessed by any of the representatives of a Purchasing Organisation the same should not be taken as a valid type test. In such cases fresh type test be insisted upon before accepting the supplies, if the orders are placed on such firms and iii) In case of these firms whose past supplies made to Nigam, testify the satisfactory performance of the equipment already supplied, a fresh type test may be waived off, in case there is no change in the design. (x) Challenge clause- There will be provision for challenge of quality from other manufacturer. The other manufacturer can also request challenge testing for any test based on specification and losses. The challenger would request for testing with testing fee. The challenger would have the opportunity to select the sample from the store and any such challenge would have to be made within guaranty period. The party challenged, challenger and utility shall witness the challenged testing. The testing will cover-1) measurement of magnetizing current: 2) no load losses test, 3) load losses test (at 50% loading or as per acceptance test): 4) temperature rise test. The challenge can be conducted at NABL accredited laboratory like ERDA and CPRI Bhopal. If products fail, the manufacturer shall be declared as unsuccessful manufacturer for the product with wide publicity and would not be allowed to compete in further Nigam tenders and heavy enalty would be imposed. 15. VAT/ CENTRAL SALE TAX The Purchaser shall pay Central Sale Tax /Value Added Tax at the prescribed rates (if applicable) on the production of the following Certificates by the supplier in triplicate: (i) Certified that the transaction in which the sales tax /Value Added Tax has been claimed has been/will be included in the return submitted/to be submitted to the Taxation authorities for the assessment of Central Sales Tax and amount claimed from the Dakshin Haryana Bijli Vitran Nigam has been/shall be paid to the Sales Tax authorities. (ii) Certified that the goods on which the Sales Tax /Value Added Tax has been charged in Bill No.___________ dt.___________ for Rs.___________ have not been exempted under the Central Sales Tax Act 1956/ Haryana VAT Act 2003 or the rules made thereunder and the charges on account of Sales Tax on these goods are correct under the provision of the relevant Act or the Rules made thereunder. (iii) Certified that we shall always indemnify the Dakshin Haryana Bijli Vitran Nigam in case it is found at a later stage, that wrong or incorrect payment had been recovered on account of Sales Tax paid/to be paid by us. (iv) Certified that we are registered as a dealer under the Central / State Sales Tax/ VAT and our registration No. is _______________.Provided that in respect of the item at Sr. __________________________and _______________ of clause – 7 which are required by the Nigam for use on the generation and distribution of electrical energy to the Public, no Haryana Sales Tax/VAT shall be payable as they are exempted under Section-27, Sub-section (I)(a)(III) of Haryana General Sales Tax Act 1973.

Page 23: qd-416

16. DOCUMENTATION : (I) All bills and/or invoices whether in respect of an advance payment or full payment,shall contain complete details of Code No., name of the item, description of material supplied, quantity supplied, rate, details of extra claims, etc. as well as the name of the consignee who received the material, shall be submitted in triplicate, duly accompanied by the receipted good challan, inspection note/test certificate in original, prescribed sales tax/ excise duty certificates and excise duty gate pass, where required. (II) All freight charges whether paid or to pay, and whether chargeable to the Nigam or included in the quoted price, shall be shown in the invoice separately. (III) All bills and/ or invoices shall be sent by the supplier to: _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ for payment. 17. TERMS OF PAYMENT:

"Subject to any deductions which the purchaser may be authorized to make under this contract, the payment for the material shall be made as under:- (a) 70% percent payment shall be made on 30th day from the date of receipt of material by the consignee or date of submission of documents i.e. bills/invoices in triplicate, receipted challan, inspection note, prescribed sale tax/excise duty certificates and excise duty gate pass wherever required etc. whichever is later.

The balance 30% payment shall be released to the firm after the receipt of report from the approved Lab. i.e. NPL/ERDA and completion of testing upto 100% testing of meters by the Departmental M&P Lab. and replacement of all meters declared defective/unfit by the M&P Lab. during their testing. Note:- NPL/ERDA testing shall be applicable for the purchases made by CGM/MM,DHBVN, Hisar & on receipt of satisfactory report of NPL/ERDA,GM(Op)s shall be placed the purchase order to the firm for their requirement after the necessary directions from the office of CGM/MM,DHBVN, Hisar. (b) The bank guarantee of the value of 10% of the contract price shall be furnished within 15 days from the date of issue of Purchase Order which should remain valid for 90 days after the expiry of warranty period, failing which:

i) Penalty @ 0.35% per week or part thereof of the value of B.G. would be charged from due date of submission, till the BG or DD in lieu of BG is submitted by the firm.

ii) In case the performance bank guarantee or DD in lieu of performance security is not submitted within 30 days from the date of issue of Purchase Order or the date if any stipulated by the DDO, the Nigam (Nodal Agency) reserve the right to cancel the Rate Contact.

Page 24: qd-416

Further a rebate of 0.35% per week or part thereof shall be availed of by the Nigam if payment is made earlier than the period specified above. The rebate will be calculated on the payable amount. All payments shall be made by the purchaser/his authorized agent to the Supplier in rupees in India."

18. NEGLIGENCE: If the supplier shall neglect to execute the work with due diligence and expedition or shall refuse or neglect to comply with any reasonable orders given in writing by the purchaser or is authorised agent in connection with this contract or shall contravene this provision of the contract, the purchaser may give 15 days notice in writing to the supplier to make good the failure, neglect or contravention complained of and should the Supplier fail to comply with the notice within the above said time from the date of service thereof (in case of failure, neglect or contravention capable of being made good, within that time or otherwise within such time as may be reasonable necessary for making it good, then in such case, the purchaser shall be at liberty to take the work wholly or in part out of Supplier’s hand and recontract at a reasonable price with any other person (s). in such event, it shall be lawful for the purchaser to retain any balance which may otherwise be due by him to the Supplier on any account, and apply the same towards the execution of the whole of balance of the work so recontracted, as aforesaid, if no such balance is due by him to the supplier or if due, is not sufficient to cover the amount thus recoverable from the supplier, it shall be lawful for the purchase to recover the whole or the balance of the amount from the supplier by action at law or otherwise. The remedy under this clause will be in addition to and without prejudice to right available to the purchaser under other clause of these terms and conditions. 19. DESPATCH OF MATERIAL AND DESPATCH INSTRUCTIONS: The supplier shall be responsible to obtain complete Despatch instructions from the purchaser before the despatch of each consignment. The supplier sufficiently pack at his own cost the material for transit so as to ensure this being free from loss or damage on arrival without opening the packages while in transit at their destination. All containers in which the material is supplied shall be non returnable. 20. REPLACEMENT AND REJECTION: Material found sub-standard or defective or not conforming to the prescribed specification in any manner, at consignee’s end shall not be accepted and an intimation to this effect shall be given to the supplier, the purchasing authority and the Controller of Stores by the consignee. The purchasing authority shall promptly take up the matter with the supplier and ask him to rectify or replace the defective/sub-standard material forthwith and in any case within a period of 45 days from the date of original supply, failing which, the Nigam shall reserve the right to get the defect rectified at the supplier’s cost or to withheld the amount equal to cost of defective material. The supplier shall also be notified that all expenses involved in the replacement by way of handling, transportation,

Page 25: qd-416

storage, etc. shall be on his account. Before lifting the material for repair/replacement the supplier shall furnish Bank Guarantee equivalent to 100% of the total cost of the material to be lifted for repair/replacement. Failure to submit Bank Guarantee or to lift the material or to repair the equipment within the stipulated period the purchaser shall entitle to deduct/ recover the full cost of the defective material from the outstanding payments/ B.Gs. of the firm. The payment so deducted/recovered shall be released after receipt of repaired/replaced material. The purchaser shall also be at liberty to suspend further dealing with the firm till the receipt of repaired./replaced material. In addition to above, the penalty on account of losses incurred due to sub standard material, would be decided by the WTDs and imposed, depending on the merit of each case. In respect of the defective/sub-standard supplies, the date on which such a supply is replaced shall be reckoned as the effective date of delivery there against and the delay shall be worked out accordingly with reference to the date on which the supply was due as per the terms of contract, for the purpose of determining penalties/liquidated damages recoverable under Clause 9(iv). The above provision shall apply mutatis-mutandis to the material found sub-standard or defective during the period of warranty. 21. TERMINATION OF CONTRACT FOR DEFAULT 21.1 The purchaser may, without prejudice to any other remedy for breach of contract, by written notice of default sent to the supplier, terminate the contract in whole or in part: (a) If the supplier fails to deliver any or all of the stores within the time period(s) specified in the contract, or any extension thereof granted by the Purchaser; or (b) If the supplier fails to perform any other obligation under the contract within the period specified in the contract or any extension thereof granted by the purchaser. (c) If the supplier, in the judgement of the purchaser has engaged in corrupt or fraudulent practices in competing for or in executing the contract (The definition of corrupt or fraudulent practices defined under clause-26). 21.2 In the event the purchaser terminates the contract in whole or in part. Performance Security(Cash/Bank Guarantee) submitted by the firm/supplier shall be forfeited. 22 SET-OFF: Any sum of money due and payable to the supplier under the contract (including Security deposit returnable to the supplier) may be appropriated by the purchaser and set-off against any claim of the purchaser for the payment of a sum of money arising out of or under this contract or any other contract entered into by the supplier with the purchaser. 23 SUPPLIER’S DEFAULT LIABILITY : In the event of breach of any these terms and conditions by the supplier, the purchaser can terminate the contract without Notice to the supplier at any stage and the supplier shall have no claim whatsoever on the purchaser on this account. But the supplier shall be liable to pay to the purchaser a sum equivalent to 10% of the value of the undelivered material as liquidated damages and not as

Page 26: qd-416

a penalty. The supplier shall in addition and without prejudice to the above said damages, make good any loss or damage that may be incurred by the purchaser on making risk purchase in terms of clause of ‘Risk purchase’. 24 LAWS GOVERNING THE CONTRACT (i) This contract shall be governed by the Laws of India for the time being in force. (ii) Irrespective of the place of delivery place of performance or place of payment under the contract, the contract shall be deemed to have been made at the place from which the acceptance of tender has been issued. (iii) Jurisdiction of courts: The courts of the place from where the acceptance of tender has been issued shall alone have exclusive jurisdiction to decide any dispute arising out of or in respect of the contract. 26 Corrupt or Fraudulent Practices The Nigam requires that Tenderers/Suppliers/ Contractors observe the highest standard of ethics during the procurement and execution of Nigam contracts. In pursuance of this policy, the Nigam:- (a) defines, for the purposes of this provision, the terms set forth as follows: (i) “corrupt practice” means the offering, giving, receiving or soliciting of any thing of value to influence the action of a public official in the procurement process or in contract execution: and (ii) “fraudulent practice” means a misrepresentation of facts in order to influence a procurement process or the execution of a contract to the detriment of the Nigam, and includes collusive practice among Tenderers (prior to or after tender submission) designed to establish tender prices at artificial, non-competitive levels and to deprive the Nigam of the benefits of free and open competition; (b) will reject a proposal for award if it determines that the Tenderer recommended for award has engaged in corrupt or fraudulent practices in competing for the contract in question; (c) will declare a firm ineligible, either indefinitely or for a stated period of time, to be awarded a Nigam contract if it at any time determines that the firm has engaged in corrupt or fraudulent practices in competing for, or in executing, a Nigam contract. 27. PATENT RIGHTS The supplier shall indemnify the Purchaser against all third-party claims of infringement of patent, trademark or industrial design rights arising from use of the Goods or any part thereof in India. In the event of any claim asserted by a third party of infringement of copyright, patent, trademark or industrial design rights arising from the use of the Goods or any part thereof in the Purchaser’s country, the supplier shall act expeditiously to extinguish such claim. If the supplier fails to comply and the Purchaser is required to pay compensation to a third party resulting from such infringement, the supplier shall be responsible for the compensation including all expenses, court costs and lawyer fees. The Purchaser will give notice to the supplier of such claim, if it is made, without delay.

Page 27: qd-416

28. SETTLEMENT OF DISPUTES If any dispute or difference of any kind whatsoever will arise between the Purchaser and the Supplier in connection with or arising out of the Contract, the parties will make every effort to resolve amicably such dispute or difference by mutual consultation. If , after thirty (30) days the parties have failed to resolve their dispute or difference by such mutual consultation, then either the Purchaser or the Supplier may give notice to the other party of its intention to commence arbitration, as hereinafter provided, as to the matter in dispute, and no arbitration in respect of the matter may be commenced unless such notice is given. 29. ARBITRATION All matter questions, disputes, differences and/or claims arising out of and/or concerning and/or in connection and/or in consequences or relating to the Contract whether or not obligations of either or both parties under the contract be subsisting at the time of such dispute and whether or not the contract has been terminated or purported to be terminated or completed, shall be referred to the arbitration which shall be conducted by three arbitrators, one each to be nominated by the supplier/contractor and the Nigam(arbitrator to be approved by the M.D. DHBVNL or authority of the Nigam authorized for the purpose by the Nigam) and the third to be named by the president of the institution of the Engineers, India. If either of the parties fails to appoint its arbitrator within thirty (30) days after receipt of a notice from the other party invoking the arbitration clause, the president of the institution of Engineers, India, shall have the power at the request of either of the parties, to appoint the arbitrator. A certified copy of the order of the institution of Engineers (India) making such an appointment will be furnished to each of the parties. The decision of the majority of the arbitrators shall be final and binding upon the parties. The parties to the contract agree that the cost of arbitration shall be as per instructions of the Nigam issued/prevalent on the date of appointment of arbitral tribunal. The arbitrators may, from time to time, with the consent of the parties enlarge the time for making the award. In the event of any of the aforesaid arbitrators dying, neglecting, resigning or being unable to act for any reason, it will be lawful for the party concerned to nominate another arbitrator in place of the outgoing arbitrator. The arbitrator shall have full powers to review and/or revise any decision, opinion, direction, certification or valuation of the Engineer in consonance with the Contract, and neither party shall be limited in the proceedings before such arbitrators to the evidence or arguments put before the Engineer for the purpose of obtaining the said decision. The objection that the Arbitrator has to deal with the matters to which the Contract relates in the course of his duties or he has expressed his views on any or all of the matters in dispute of difference, shall not be considered as a valid-objection. Subject to aforementioned provisions, the provisions of the Arbitration and conciliation Act, 1996 and the Rules thereunder any statutory modifications thereof for the time being inforce, shall be deemed to apply to the Arbitration proceedings under the clause. Where the value of the Contract is Rs. One Crore and below, the disputes or differences arising will be referred to the Sole Arbitrator. The Sole Arbitrator to be approved by the M.D.

Page 28: qd-416

DHBVNL or authority of the Nigam authorized for the purpose by the Nigam. Notwithstanding any reference to arbitration herein, (a) The parties will continue to perform their respective obligations under the Contract unless they otherwise agree; and (b) The Purchaser will pay the Supplier any monies due to the Supplier. Place : Date : Signature of the Supplier.

Page 29: qd-416

ANNEXURE ‘A’ TO SCHEDULE ‘D’ SPECIFICATIONS

Note: Advance sample strictly in accordance with the above specifications Submitted (delete if not applicable). __________________________ Signature of the Supplier,

Page 30: qd-416

ANNEXURE ‘B’ TO SCHEDULE ‘D’

SCHEDULE OF DELIVERIES (At least 20 days advance intimation shall be given by the supplier to each consignee before the dispatch of the material failing which demurrage/wharfage charges will be to the account of the supplier). Sr.No. Name of Item Specification Name of

Consignee Delivery

Place: Name & Full Address of Tenderer Date:

Page 31: qd-416

Schedule A,C,F to I shall be as per DHBVN Procurement Manual. Schedule-D should be got signed from the supplier by the Direct Demand Officer while issuing supply order/purchase order.

Page 32: qd-416

(1) ANNEXURE ‘A’ TO SCHEDULE ‘D’ SPECIFICATIONS: Note: Advance sample strictly in accordance with the above specifications is/has been Submitted (delete if not applicable). __________________________ Signature of the Supplier, Complete Address ( Rubber Stamp) Contd. Next Page

Page 33: qd-416

( TO BE FILLED IN AND SIGNED BY THE TENDERER) SCHEDULE OF DEVIATIONS We/I have carefully gone through the technical specification and the general conditions of contract and We/I have satisfied ourselves/myself and hereby confirm that our/my offer strictly conforms to the requirements of the technical specifications and general conditions of contract except for the deviations which are given below:- Sr.No.

Description Stipulation in specification

Deviations offered

Remarks

A. Commercial Terms: Clause No. B. Technical Specifications Clause No. ( Please use more sheets, if required). Signature : Name : Status : Whether Authorised Attorney Dated: of the Tendering Company Place: Name of the Tendering Company

Page 34: qd-416

PRICING SCHEDULE A Quoted Firm price FOR

Destination Inclusive all statutory levies i.e. ED,CST, F&I etc.

B. Break up of Price 1. 2.

Ex works prices Excise Duty, if applicable.

3. Rate of insurance and total charges as included in the price at Sr.No.A above.

4. Freight Charges etc. as included in the price at Sr.No.A above.

5. Rate of CST/VAT as applicable. 6. Any other duty/levy or other tax 7. Discount 8. Delivery 9. Validity 10. Terms of payment

11. Modvat benefits ( whether will be reimbursed to DHBVN)\

12. Deviations from our standard terms and conditions, if any, may clearly be mentioned above.

Note: In case of silence of any clause above, it shall be considered that quoted rates are inclusive of FOR Destination Prices of Sr.No.A. Modvat: Modvat benefits will be considered to be passed on to DHBVN in case of non-commitment as above. Name & Designation Seal of Company

Page 35: qd-416

ANNEXURE-I

AFFIDAVIT

I,_____________________________________Direcor of

M/s _____________________________________________________________

with Headquarter at ______________________________ being their authorized

signatory, do hereby solemnly affirm and declare that M/s __________________

has not been blacklisted by any State/Central Govt. or any of its agencies. I

understand that if upon acceptance of our offer dated _________________

against DHBVN tender enquiry No._______________________ for supply of

________________________________________________ any P.O. is placed

upon us, the same is liable to be cancelled. If this declaration is found wrong at

any subsequent time and further I understand to compensate the DHBVNL, for

the consequences arising out of wrong declaration.

_________________________ _________________________ _________________________ Attested by Oath Commissioner.

Page 36: qd-416

DAKSHIN HARYANA BIJLI VITRAN NIGAMOffice of the Chief General Manager/P&D,

Vidyut Sadan, Vidyut Nagar, Hisar-125005

Tel: 01662-221285, 221830 (GM/P&D) Fax: 01662-220481

Specification No. S-124/DD-177/Vol-IV/Version-II

TECHNICAL SPECIFICATIONS

FOR WHOLE CURRENT A.C. SINGLE PHASE TWO WIRE

STATIC ENERGY METER

OF

ACCURACY CLASS1.0(10-60A)

WITH COMMUNICATION FACILITY

Issue of the Month :Nov. 2007

Page 37: qd-416

DAKSHIN HARYANA BIJLI VITRAN NIGAM

TECHNICAL SPECIFICATIONS FOR WHOLE CURRENT A.C.SINGLE PHASE TWO WIRE STATIC ENERGY METER OF ACCURACY CLASS 1.0(10-60A) WITH

COMMUNICATION FACILITY

1. SCOPE The specification covers the design, manufacturing, testing, supply and

delivery of AC whole current 1 phase 2 wire static watt hour meter for measurement of active energy (kWH) with initial and sustained accuracy of class 1.0 for solidly earthed system with balanced and unbalanced loads having power factor in the range of zero to unity(Lagging/Leading).

2. APPLICABLE STANDARDS

Unless otherwise especially modified and to the extent so modified from

these specifications, the meter shall comply with the latest version of IS-13779, IEC-1036 and CBI&P Technical report 88/1998(latest amendment). Further meters from ISO Certified manufactured shall be preferred.

3. CLIMATIC CONDITIONS

i) Temperature -2.5°C to 60°C ii) Humidity Max. 95% iii) Average annual rain fall 150cm. iv) Max. wind pressure 150kg/Sq.m v) Max. Altitude above MSL 1000 Meters

4. TROPICAL TREATMENT

The meter shall be suitably designed and treated for normal life and satisfactory operation under the hot and hazardous tropical climate conditions and shall be dust and vermin proof. All the parts and surface, which are subject to corrosion, shall either be made of such material or shall be provided with such protective finish which provides suitable protection to them from any injurious effect of excessive humidity.

5. ELCTRICAL SPECIFICATION AND PERMISSIBLE TEMPRATURE

i) Class of accuracy 1.0(No drift in tolerance of accuracy for 10 years) ii) Supply voltage 240V AC With +20% to (-)40% variation iii)Frequency 50Hz +/-5% GM/P&D CGM/P&D CGM/MM CGM/Commercial

Page 38: qd-416

iv) Current range(basic)Ib 10A v) Max. current 600% for Ib=10Amp. vi)Current rating 10-60A vii)Starting current 0.2% Ib at unity power factor viii) Power factor range 0 to 1 (Lagging & Leading) ix) Power loss As per ISS-13779 x) Resistance to surge voltage >6kV peak As per ISS-13779 1.2/50Micro sec. IEC-1036/CBIP-88 xi) test voltage of 50Hz for 1 Min. 2kV rms xii) Clock time accuracy +/- 5 ppm at 25°C xiii) Temperature rise As per ISS-13779 xiv) Power consumption by meter As per ISS-13779 6 Auto Display The meter shall have LED/LCD backlit type electronic display with minimum six digit with another digit leg-end. The decimal digit shall be clearly distinguished from integral digit. The single phase electronic meters shall be capable to measure and display Internal diagnostics test, kwh, Maximum Demand(MD)kw, date and time at all loads and Power Factor, cumulative kwh shall be indicated continuously by default on auto scroll and other parameters through push botton. The registered parameters i.e. the data stored in meter shall not be lost/ effected in the event of power failure. The display shall also not be effected by electric and magnetic disturbances. The meter shall have non volatile memory (NVM) which does not need battery back up . The NVM shall have minimum retention period 10 years. The minimum character height shall be 8.5mmx5mm. Impulse Counter & Stepper Motor shall not be provided in the meter. The M.D. Integration period shall be for 30 minutes. a) Meter shall store M.D. in every 30 min. period along with date and time. At the end of every 30 min. new MD shall be previous M.D. and store whichever is higher and the same shall be displayed. b) It should be possible to reset MD automatically at the defined date (or period) or through MRI. The re-setting shall be automatic at the end of every month i.e. 24 hours of last day of month. Four last M.D. values shall also be stored in the memory also with auto reset count. In addition to this the cumulative kwh should also be stored in the memory at 0-00 hrs. at the end of every month. The meter should be capable of storing last 4 month data with an option to retrieve the same. c) Manual MD resetting using scalable push button is an optional. The display order shall be :- a) Default Display(Continuously on auto scroll). i) Cumulative Active Energy kwh. b) On Demand Display(with push button) i) Internal diagnostics ii) cumulative kwh iii) Date iv) Real Time v) Current MD in kw vi) Last month reading billing date vii) Last month billing kwh reading viii) Last month billing MD in KW

GM/P&D CGM/P&D CGM/MM CGM/Commercial

Page 39: qd-416

ix) Last month billing MD in KW occurrence Date x) Last month billing MD in KW occurrence Time xi) Meter Serial Number The meter’s display should return to default display mode (continues auto scroll) if push button is not operated for more than 10 seconds. ii) BILLING DATA a) Meter serial number, Date and time, KWH, MD in KW, History of KWH & MD for last 6 months along with TOD readings. b) All the above parameters (namely KWH,MD in KW) are meter readings. c) All these data shall be accessible for reading, recording and spot billing by downloading through optical port on MRI or Laptop computers. iii) TOD METERING Meter shall be capable doing TOD metering for KWH and MD in KW with 6 time zones (programmable on site through CMRI). The 6 time programmable will be intimated at the time of placement of order to the successive bidder.

7.ANTI TAMPER FEATURES The meter shall not be affected by any remote control device and shall

continue recording energy under any one or combinations of the following condition.

i) The meter shall be capable of recording energy correctly even if input and output terminals are interchanged. Also the meter shall record correctly even if phase and neutral are inter changed.

ii) The meter shall register energy even the load is not terminated back to the meter and instead current is drawn through a local earth under the conditions.

a) I) When phase and neutral are connected correctly. II) When phase and neutral wires connected are interchanged at input terminals.

b) Also when only phase is available either in neutral or phase terminal and earth loading has been done. In such circumstances only minimum starting current of 2 Amp. Should be drawn and in other conditions as per relevant ISS.

iii) The meter shall be factory calibrated through software and no modification of calibration shall be possible at site by any means what-so-ever. Trim pot method for calibration shall not be

acceptable. No mechanical or potentiometer like devices shall be used for meter calibration that possibly can alter the meter accuracy either in case of change in climatic conditions or intentionally at site. Calibration Certificate/Routine test certificate should be supplied with the dispatch.

GM/P&D CGM/P&D CGM/MM CGM/Commercial

Page 40: qd-416

iv) Meter shall record the energy accurately under the effect of radiation emitted by mobile phone. The test shall be carried out by bringing a mobile phone in the case proximity of the meter for 10 minutes when there is an incoming call and shall be checked under the following condition:

a) 10% Ib and UPF b) 50% Ib and UPF c) Ib and UPF d) Ib and 0.8PF e) 125% Ib and UPF

v) The Meter shall immune to the external magnetic field upto 0.5 Tesla with permanent magnet of 75x75x35 mm and in case external magnetic field exceeding 0.5 Tesla(permanent magnet), the meter shall log the event of attempt of tampering by the external magnetic field, occurrences & restoration with date & time and the meter shall start record energy at maximum current Imax under such influence of abnormal magnetic field irrespective of actual load. The meter shall record as per actual load once the external abnormal magnetic field is removed.

vi) Meter shall immune of any abnormal frequency signal OR Meter shall log & display as tamper in the event abnormal frequency signal i.e. less than 47.5Hz OR more than 52.5 Hz is supplied to the meter.

vii) Load Survey-Load survey for all the billing Para Meters/Anti Tamper Features should be available for 60 days.

viii) Minimum 200 number of events(occurrences & restoration with date & time of more than 20 minutes) shall be available in the meter memory on roll over facility. All the information shall be available in a standard simple format.

The meter shall work satisfactorily under presence of various influencing conditions like External Magnetic Field, Electromagnetic Field, Radio Frequency Interference, Vibrations, harmonic Distortion, Voltage/ Frequency Fluctuations, and electromagnetic High Frequency Fields etc. The meter shall immune to affect by abnormal voltage/frequency generating devices such as consisting of Scooter Ignition oil and Fan Regulator/Filter Circuit etc. To this effect a test certificate must submitted by the bidder from any Govt. approved NABL Lab/Power Utility as per following caretaria. The accuracy of the meter should not be affected with the application of abnormal voltage /frequency generating device ( having spark discharge of approximately 35kV. The meter in any of the following manner for a total period of 10 minutes: a) On phase or neutral terminals b) On any connecting wires of the meter. c) Voltage discharge with 0-10mm spark gap d) Spark on meter body

GM/P&D CGM/P&D CGM/MM CGM/Commercial

Page 41: qd-416

e) At any place in load circuit The accuracy of meter should be checked before & after the application of said devices.

i. 8. CONSTRUCTION

i) DESIGN Voltage circuit, sealing arrangement, terminal block, terminal cover and

nameplate etc. shall be in accordance with IS-13779 (latest version). The meter shall be compact and reliable in design, easy to transport and immune to vibration and shock involved in transportation and handling. The construction of the meter shall ensure consistent performance under all conditions especially during dust storm/heavy rains/very hot weather. The insulating material used in the meter should e non-hygroscopic, non-aging and of tested quality. The meter should be sealed in such a way that the internal parts of the meter are inaccessible.

Further meter shall withstand an insulation test of 4 KV and impulse test at 8KV & the terminal block and meter case shall have safety against spread of fire. They shall not be ignited by thermal overload of live parts in contact with them as per the relevant IS-13779 ii) CIRCUITARY: The meter shall have an operational indication device such as blinking LED given type indication. The following indications are mandatory. 1. Meter Calibration.

2. Phase available indication 3 Load earthling . 4. Current reversal. The operation indicator should be accessible from the front. The mounting of components on the PCB (Printed Circuit Board) shall preferably be SMT (Surface Mounted Technology) type. The Electronic Components used in the meter shall be of high quality and there shall be no drift in the accuracy of the meter at least upto 10 years. The circuitary in the meter shall be compatible with 2x8 bit (or better) processor and the meter shall be based on digital measuring and sampling technique. III) METER CASE & COVER The meter case & cover will either be ultrasonically welded or shall have push fit type arrangement with two No. Aluminium seals, one each on either side, so that Meter’s internal parts are only accessible after breaking seals, ultrasonic welding, push fit arrangement or case/cover of the meter and it should become unserviceable. The material for base and transparent cover of the meter shall be of thermoplastic/engineering plastic respectively.

ii) THERMO SETTING PLASTIC.

Self-insulating non-corroding black thermosetting material, which would ensure maximum strength against distortion and also injury to working part during normal use and rough handling during transportation. The material shall not soften/melt on heating.

GM/P&D CGM/P&D CGM/MM CGM/Commercial

Page 42: qd-416

(b) ENGINEERING PLASTIC The meter casing material should be glass reinforced, flame retardant,

unbreakable engineering plastic material to ensure high reliability, long trouble free life, safety against electric shock, spread of fire and effect or excessive temperature. The material shall be corrosion resistant &invert to chemicals, oxidizing agents, petro chemical products, acids, salts and ultraviolet radiation. The meter chamber shall be dust proof and moisture proof. The supplier should indicate hardness, melting temperature and tensile yield strength of the material and necessary test certificates of the same shall be furnished. The meter case and cover should be sturdy enough to prevent damage during transportation and installation.

The engineering plastic housing used may be provided with a key whole on the top for fixing which should not be accessible to the consumer after terminal cover is sealed. The meter shall withstand external magnetic influence as per latest amendments of CBIP 88. The engineering plastic used shall conform to ISS 11731 besides meeting the test requirement of heat reflection test as per ISO-75 and Glow wire test as per the relevant standards.

i. TERMINAL BLOCK & COVER

The terminals may be grouped in a terminal block having adequate insulating properties and mechanical strength. The terminal block shall be made from best quality non-hygroscopic, flame retardant material (capable of passing the flammability tests given in IS-11731) with nickel-plated brass or aluminium alloy for connecting terminals. The clamping screw should be provided inside the terminal cover and should have metallic sleeve molded within the block to avoid damage during tightening of the screws.

The terminals in the terminal block shall be of adequate length in order to have proper grip of conductor with the help of two screws through agency of a plate so as to made cage type arrangement. The screws shall have thread size not Less than M4 and head having- 4 -6 mm diameter. The screw shall not have pointed ends at the end of threads. All terminals and connecting screws and washers should be of tinned/nickel plated brass material or Aluminium alloy.

The internal diameter of terminal hole shall be min. 8.5 mm and should comfortable accommodate the 50 mm2 cable conductors. The holes in the insulating material shall be of sufficient size to accommodate the insulation of conductor also.

The terminal cover shall be engineering plastic with minimum thickness 2.5 mm and the terminal cover shall be of extended type completely covering the terminal block and fixing holes except for the provision of conductor entry at the bottom for incoming and outgoing leads. The terminal cover shall be so provided that it remains permanently connected with meter base. The supplier shall suitably design the cover so that it opens or closes like a hinged door and the ends of hinged pins shall be flattened so that it does not come out. Provision for Minimum one number utility seal(s) as the terminal cover shall be made.

GM/P&D CGM/P&D CGM/MM CGM/Commercial

Page 43: qd-416

Supply voltage circuit is to be connected solidly from inside. (v) CURRENT & PRESSURE COILS a) Current Circuit As per IS- 13779 b) Potential Circuit As per IS-13779. i.e Voltage Circuit (vi) FIXING ARRANGEMENT Every meter shall have three fixing holes one at the top and two at the bottom. The top hole shall be provided with a special clip at the back of the mater so that holding screw is not accessible to the consumer after the fixing of the meters. The lower fixing screws shall be provided under the sealed terminal cover. The requisite fixing screws shall be supplied with each meter. (vii) SEALING: Minimum 2 No. unidirectional sealing screw shall be provided for proper fixing of meter cover with 2 No. Aluminium seals on adjacent/ side so that meter internal parts are only accessible after breading the seals, ultrasonic welding/push fit arrangement of case/cover of the meter. (viii) OUTPUT DEVICE The meter shall have a test output device in the form of a pulse indicator accessible from the front and capable of being monitored by suitable testing equipment. (ix) ELECTRONIC COMPONENTS The meter shall be from high accuracy and reliable surface mount Technology (SMT) components. The supplier should submit the details of source/agencies from whom purchase of various components of meters used by them, has been done, to the authorized representative/ team deputed by Nigam for its verification. (x) SOFTWARE & COMMUNICATION COMPATIBILITY

a) Optical port with Rs 232 compatible to transfer the date locally through CMRI & remote through PSTN /Optical fiber/ GSM/CDMA/RF/any other technology to the main computer. The optical port should be operated outside of Self locking Meter Cover Box (MCB).

GM/P&D CGM/P&D CGM/MM CGM/Commercial

Page 44: qd-416

b) The Supplier shall supply Software required for CMRI & for the connectivity to AMR modules. The supplier shall also provide training for the use of software. The software should be compatible to Microsoft Windows systems (windows 98 system). The software should have polling feature with optional selection of parameters to be down loaded for AMR application.

c) Necessary provision shall be made in the software for converting all the

parameters available for new and old meters if supplied earlier. Copy of operation manual shall be supplied.

d) The data transfer (from meter to CMRI /AMR equipment) rate should be

minimum 1200 bps,

e) The supplier shall provide meter reading protocols. 9. (i) TESTS TYPE TESTS & TEST CERTIFICATES Meters shall be fully type tested as per IS: 13779 (latest version). The type test certificates shall be submitted along with the offer. Offer without Type Test Report shall be liable for rejection. The Type test certificates shall not be more than 3 years old. Test certificates of appropriate range shall be accepted. The type certificates shall be from institutions as per Appendix ‘G’ of CBIP Technical report 88 (amended) ii) ROUTINE TESTS The Acceptance and Routine tests shall be carried out as per latest version of IS-13779. iii) EFFECT OF MAGNETIC FILED OF EXTERNAL ORIGIN. The meter shall be provided with adequate magnetic shielding so that any external magnetic field (AC electro-magnets/DC magnet) as per the value specify in CBIP technical report-88 (with latest amendment) application on the meter shall not effect the proper functioning and recoding of energy as per error limits prescribed by CBIP. However, the test certificates of the designed meter for AC abnormal magnetic field & DC abnormal magnetic field as per clause 5.6.2 of CBIP -88 report (with latest version) shall be for magnetic strength of 0.27 tesla AC & 0.5 tesla DC (permanent magnetic as well as electro-magnet) respectively. The required test certificate for the design rating of meter from the Govt. recognized/approval test house shall be submitted by the bidders along with the bid.

GM/P&D CGM/P&D CGM/MM CGM/Commercial

Page 45: qd-416

10 (i) ACCURACY & LIMITS OF ERRORS The error of meters shall not exceed the permissible limits per standard IS 13779 (latest version) and CBI&P Technical Report 88/1998 (with latest amendment) for a period of at least 10 years from the date of supply. In case any drift is notified which is beyond the permissible limits, the bidder shall re-calibrate the meter for correct accuracy and if re-calibration is not possible, the meter shall be replaced by a new meter without any extra cost. ii) STARING CURRENT The starting current of the meter shall be 0.2% lb at unity power factor.

iii) RUNNING AT NO LOAD The meter should comply with the requirements of IEC 1036/IS-13779 and CBI&P Technical Report 88/1998 (Latest amendment) iv) D.C IMMUNITY TEST The meter should comply with the requirements of IEC 1036/IS-13779 and CBI&P Technical Report 88/1998 (Latest amendment) v) INFLUENCE QUANTITIES The meter shall work satisfactorily with guaranteed accuracy as per limit of IS 13779 and CBIP Technical Report 88/1988 (with latest amendments) under presence of the following quantities:

a) External Magnetic field 0.5 Tesla. b) Electro Magnetic Field. c) Radio Frequency interference. d) Vibration. e) Harmonic wave form. f) Voltage fluctuation. g) Electromagnetic high frequency field.

vi) ELECTROMAGNETIC COMPATIBILITY

The above shall conform to requirements listed in IS-13779 and IEC-1036 and CBI&P Technical Report 88/1998 (Latest Amendments) and should be protected against radiated interference from either magnetic or radio frequency sources. The meter shall also withstand DC immunity test so as to ensure that the meter does not saturate on passage of direct current.

GM/P&D CGM/P&D CGM/MM CGM/Commercial

Page 46: qd-416

vii) METER POWER SUPPLY The meter should withstand the maximum system voltage i.e 440

volts continuously. In case of failure of power supply, the meter should display the measured quantities through an in built battery facility/External power pack unit having life more than five years (Kept in view that these meters will be installed in self locked Meter Cover Box).

11. INSPECTION

i) All meters shall be duly tested and sealed by the firm at their premises prior to inspection. ii) The Nigam Inspecting Officer will inspect the meter as per sampling plan of ISS 13779 ( latest version). Max. for size/lot of 10,000 numbers shall be considered for acceptance test as per ISS 13779. The inspecting agency can carry out any type test which felt necessary as acceptance test at firm’s works. After testing, these sample meters shall be additionally sealed by the inspecting officer and one copy of the inspection report will be handed over to the manufacturer. iii) The supplier should submit the details of source/ agencies from whom purchase of various components of meters used by them, has been done, to the authorized representative/ team deputed by Nigam for its verification. 12.PACKING

The meters shall be suitably packed for vertical/horizontal support to withstand handling during transport. The bidder shall be responsible for any damage during transit due to inadequate or improper packing. The meters shall preferably be supplied in thermocol packing of minimum 10 mm thickness.

13. GUARANTEE

h) The meter shall have a design life of at least 10 years and supplier shall be made responsible to replace free of cost, with no transportation or insurance cost to the Nigam, up to the destination, the whole or any part of the material which in normal and proper use proves defective in quality or workmanship, subject to the condition that that the defect is noticed within 66 months from the date the material is received by the consignee or 60 months from date of installation whichever period may expire earlier. The consignee or any other officer of the Nigam actually using the material will give prompt notice of each such defect to the supplier as well as the Purchasing authority and the Controller of Stores. The replacement shall be effected by the supplier within a reasonable time, but not, in any case, exceeding 45 days. The supplier shall also arrange to remove the defective supply within a reasonable period but not exceeding 45 days from the date of issue of the notice in respect thereof. Upon the firm failing to do so, the damages/ defects may begot rectified by the Nigam and the cost adjusted from the firm’s pending dues and/ or security deposit against this or any other contract in force and the balance left be got deposited good by the supplier. The Nigam may withhold the amount equal to cost of defective

GM/P&D CGM/P&D CGM/MM CGM/Commercial

Page 47: qd-416

Material. These provisions shall, also equally apply to the replaced material. In case, the material is again found to be defective within warranty period, it shall, also, have to be replaced similarly.

ii) Manufacturers supplying the meter shall guarantee temper proof features in the meters supplied by them. 14. QUALITY ASSURANCE PLAN The design life of the meter shall be minimum 10 years and to prove the design life, the firm shall have atleast the following Quality Assurance Plan: i) The factory shall be completely dust proof. ii) The testing rooms shall be temperature and humidity controlled as per relevant standard. iii) The testing and calibrating equipment should be automatic and all test equipment shall have their valid calibration certificates. iv) Power supply used in testing equipment shall be distortion free with sinusoidal wave-forms and maintaining constant voltage current and frequency as per the relevant standards. v) During the manufacturing of the meters the following checks shall be carried out:

a) Meter frame dimension tolerance shall be minimum. b) The assembly of parts shall be done with the help of jigs and fixtures so

that human errors are eliminated. c) The meters shall be batch tested on automatic, computerized test bench and the

results shall be printed directly without any human errors. 15. NAME PLATE AND MARKING

Every meter shall have a name plate clearly visible and indelible and distinctly marked in accordance with IS 13779 ( latest version). The following information should appear on an external plate attached to the meter cover:

i) Manufacturer’s name or trade mark and place of manufacture. ii) Designation of type.

iii) Number of phases and number of wires for which the meter is suitable. In addition to above, the following information shall be marked on a name plate preferably placed with in the meter:

i) Sr.No. and year of manufacture ii) Principal unit in which the meter records. iii) Reference voltage. iv) Basic current and rated maximum current. v) Reference frequency in Hz. vi) Meter constant. vii) Class index.

viii) Reference temperature. ix) The words properties of ‘DHBVN’ or ‘UHBVN’ depending upon the name of Nigam to whom meters are supplied. 16. TESTING AND MANUFACTURING FACILITIES The bidder shall have at least the following testing facilities to ensure accurate calibration:

GM/P&D CGM/P&D CGM/MM CGM/Commercial

Page 48: qd-416

a) Insulation resistance measurement. b) Running at no load. c) Starting current test. d) Limits of error. e) Range of adjustment. f) Power loss in voltage and current coil. g) Repeatability of error. h) Transportation test. i) Low load run test. j) Heating test. k) Effect of Magnetic field of external origin as per clause 5.6.2. of CBIP Report-88 with latest amendments & provision of Nigam Technical Specification. 17. ANNEXURES The bidder shall submit the following Annexures (as per format) which are part and parcel of the specification: Annexure A Guaranteed and Technical particulars. Annexure B Deviation from specifications. Annexure C Deviations from specified standards. Annexure D Deviations from specified test requirements. Annexure E Bidder’s experience. Annexure F List of Component Specification

GM/P&D CGM/P&D CGM/MM CGM/Commercial

Page 49: qd-416

ANNEXURE-A GUARANTEED TECHNICAL PARTICULARS FOR SINGLE PHASE STATIC METER Sr. No.

Description Values

1. Maker’s Name 2. Meter Make & Type 3. Fixing Arrangement 4. Basic current(Amperes) 5. Rated Maximum

Continuous Current (Amperes)

6. Standard Reference Voltage & Frequency

7. Class of accuracy 8. Power Loss in each i) Voltage circuit ii) Current circuit 9. Minimum Starting Current 10. Type of display 11. No. of Digits 12. Type of output Device 13. Clearances and creepage

distance in the

i) Terminal Block ii) Terminal cover iii)Internal parts of the

meter

14. Material of i) Terminal Block ii) Terminal cover 15. Material of Terminals 16. Material of Meter

Frame/Cover

17. Window arrangement & material

18. Number of seals provided i) Main Meter Cover ii) Meter Terminal Cover 19. Total weight of the Meter

Page 50: qd-416

ANNEXURE-B DEVIATIONS FROM SPECIFICATIONS

____________________________________________________________________ Sr. No. Specification

Clause No. Requirement of Deviation

Proposed Specification

Reasons for Deviation

____________________________________________________________________

1. Name of firm 2. Name & signature of

tenderer 3. Designation 4. Dated

Page 51: qd-416

ANNEXURE-C

DEVIATIONS FROM SPECIFIED STANDARDS ____________________________________________________________________

Sr. No. Particulars Stipulation of

Specified standard ………………. Standard Stipulation Ref.

Stipulation standard adopted By tenderer ……………… Standard stipulation Ref.

Remarks

____________________________________________________________________

1. Name of firm 2. Name & signature of

tenderer 3. Designation 4. Dated

Page 52: qd-416

ANNEXURE-D

DEVIATIONS FROM SPECIFIED TEST REQUIREMENTS SPECIFIED IN RELEVANT & PRESENT SPECIFICATION

………………………………………………………………………………………………….. Sr. No.

Name of test Standard No. & Clause No.

Requirement of standard

Proposed Deviation

Reasons for Deviations

…………………………………………………………………………………………………..

1. Type test 2. Acceptance test

1. Name of firm 2. Name & signature of

tenderer 3. Designation 4. Dated

Page 53: qd-416

ANNEXURE-E

BIDDER’S EXPERIENCE

………………………………………………………………………………………………….. Sr. No.

P.O. with date

To whom Supplied

Description of material

Qty. Status of P.O.

Remarks

…………………………………………………………………………………………………..

1. Name of firm 2. Name & signature of

tenderer 3. Designation 4. Dated

Page 54: qd-416

ANNEXURE-F List of Component Specification

Sr. No.

Component Function

Requirement Makes and Origin Bidder’s offer (should be within the specified make or equivalent better)

1. Current Transformers

The Meters should be with the current transformers as measuring elements. The current transformer should withstand for the clauses under 5.2h

The current transformer should withstand for the clauses under 5.2h

2. Measurement or computing chips

The Measurement or computing chips in the meter should be with the Surface mount type along with ASICs.

USA: Anolog Devices,Cyrus Logic,Atmel,Phillips,Texas Instruments. South Africa: SAMES Japan: Hitachi or Oki

3. Memory Chip The memory chips should not be affected by the external parameters like sparking high voltage spikes or electrostatic discharges.

USA:Atmel,National Semiconductors,Texas Instruments,Phillips,ST. Japan: Hitachi or Oki

4. Display modules

a) The display modules should be well protected from the external UV radiations. b) The display visibility should be sufficient to read the Meter mounted at height at 0.5 meter as well as at the height of 0.2 meters (ref 3.2d for Viewing angle). c) The construction of the modules should be such that the displayed quantity should not disturbed with the life of display (PIN Type) d) It should be trans reflective HTN or STN type industrial grade with extended temperature range.

Honkong: Genda Singapore : Bonafied technologies. Korea: Advantek China: Success Japan: Hitachi, Sony

Page 55: qd-416

5. Communication

modules Communication modules should be compatible for the two Ts 232 ports (one for optical port for communication with meter reading instruments & the other- for the hardwire Rs 232 port to communication with various modems for AMR)

USA: National Semiconductors, HP, Ontonica, ST Holland/Korea: Philips Japan: Hitachi Taiwan:Ligitek Germany: Siemens

6. Optical Port Optical Port should be used to transfer the meter data to meter reading instrument. The mechanical construction of the port should be such to facilitate the data transfer easily.

USA: National Semiconductors, HP, Holland/Korea: Philips Japan: Hitachi Taiwan:Ligitek

7. Power Supply The power supply should be with the capabilities as per the relevant standards. The power supply unit of the meter should not be affected. In case the maximum voltage of the system appears to the terminals due to faults or due to wrong connections.

It should take care of clause 5(ii) and 5(xiv)

8. Electronic Components

The active & passive components should be of the surface mount type & are to handled & soldered by the state of atr assembly processes.

USA: National Semiconductors, Atmel, Philips, Texas Instruments, Texas, ST, Onsemi Japan: Hitachi, Oki, AVX or Ricoh Korea: Samsung

Page 56: qd-416

9. Mechanical

Parts a) The internal

electrical component should be of electrolytic copper & should be protected from corrosion, rust etc.

b) The other other mechanical components should be protected from rust, corrosion etc. by suitable plating /painting methods.

10. Battery Lithim with guaranteed life of 15 years.

Verta,Tedirun, Sanyo or National

11. RTC & Micro controller

The accuracy of RTC shall be as per relevant IEC/IS standards

USA: Philips, Dallas, Atmel, Motorola, Microchip Japan: NEC or Oki

12. P.C.B. Glass Epoxy, fire resistance grade FR4, with minimum thickness 1.6mm

(BBT test is must)