PTO/Wet Line Kits

WA06 Series WA08 SeriesThe WA06 series PTO has been designed to work with most of the existing transmissions in the market. It is a very durable PTO with a wide range of input gears, shifters, speed ratios and output shafts to meet market applications.

The WA08 PTO is our WA06 PTO with the ability to mount on the 8 Bolt Transmission opening. This design uses no adapter plates and cuts down on leaks and installation time. It has an “A” ratio that is not offered in the WA06 model. It is a very durable PTO with a wide range of input gears, shifters, speed ratios and output shafts to meet market applications.

Meritor Transmissions

WA08 Left Side MountWA06 Right Side Mount

Eaton/Fuller Transmissions

WA8S or WA8G If WA8G (bottom mount) use stud kit MW1WA20-03-1116 and use WA8S PTO SeriesWA6S or WA6G If WA6G use stud kit MW1WA20-03-1071 and use WA6S PTO Series

Mack Transmission

WA8D Left Side Mount - exceptions apply, please check applicationsWA6D Right Side Mount - exceptions apply, please check applications

Note: All PTOs are stocked without an air shift installation kit. If installation kit is needed please add P/N MW1WA101X for single controller

POWER TAKE-OFF UNITS

Power Take-Off Units ∙ PTO Controls & Accessories ∙ Tanks Hydraulic Hose & Fittings ∙ Couplers ∙ In-Line Filter Kits

Dump Pumps & Walking Floor Pumps ∙ Gear Pumps & Motors Clamps ∙ Gaskets ∙ Steel Spacers & More!

**Please provide transmission model and percentage engine speed required for application**

Walking Floor Pumps

Gear Pumps & Motors

Hotshift PTO

Hydraulic Tank & Mounts

Dump Pumps

Towers & Controllers

Hose Kits w/ Fittings

• PTO housing is made of cast iron with an increased mounting flange radius for heavy duty applications. • World American uses a cast iron rotatable flange with tapped holes makes installing the pump easier. The plug and gasket are included to increase the life of the splines.

• World American PTO mounting kit include 2 studs to make installation of the PTO easier.

Power Take-Off Units

Metric Stud Kit MW1WA20-03-1060 Metric Stud Kit MW1WA20-03-1056

CATA

LOG

NUM

BER

24

www.midwestwheel.com

Order NLINE™

www.midwestwheel.com

Order NLINE™

MW1WAA50SSAluminum Saddle

GASKETS STEEL SPACERS Other Thicknesses Available

6-Bolt 8-Bolt

6-Bolt 8-Bolt ThicknessMW1WA6010 MW1WA8010 .010MW1WA6020 MW1WA8020 .020MW1WA6032 MW1WA8032 .032

6-Bolt 8-Bolt ThicknessMW1WA6062 MW1WA8062 .062MW1WA6093 MW1WA8093 .093

Adapter Gears Available!

Base dimensions are 4 1/2” x 5” to center of the bolt holes. These towers will accommodate our current dual controllers and our single controller. These towers are made of sturdy steel construction.

The single controller operates the engagement and disengagement of the PTO. The dual controller operates the engagement and disengagement of both the PTO and the pump. Includes hose, fittings, valve, and LED Light

MW1WA101X Single ControllerMW1WA201X Dual Controller with KickoutMW1WA202X Dual Controller w/o Kickout

MW1WA600221 8" TowerMW1WA600222 10" TowerMW1WA600223 12" Tower

PTO CONTROLS & ACCESSORIESPTO Towers

PTO Air Controller Kits

TANKS ALL TANKS HAVE TWO (2) 2" NPT SUCTION PORTS

The valve is a more defined 3 position 4 way feathering valve. Features precise control & feathering while dumping a load of stone or asphalt. Comes with a heavy duty body & control lever. Also equipped w/ a safety lockout device to prevent unintentional lever movement.

MW1WA4306-10 10' PTO CableMW1WA4306-15 15' PTO CableMW1WA4306-20 20' PTO CableMW1WA4306-25 25' PTO Cable

PTO Cables

PTO Feathering Valve MH1MPN600507

Console Tower for Feathering Valve - BY K1010C

P/N BY AS1 - To air shift w/ feathering valve

• Integral load holding check valves prevent reverse flow through valve when shifting

• Balanced, select-fit spools provide minimum leakage, smooth operation

• External spool seals permit easy replacement, reduced maintenance cost

• Single Spool (4-Way Spool Action) • Rated Working Pressure 2500 PSI • Max. Shock and Surge Pressure 4000 PSI • Rated Flow Capacity 30 GPM • 3/4” SAE inlet and outlet ports; 3/4” SAE work ports • Integral differential poppet type relief valve, adjustable

Directional Control Valves - BY HV11AG00D0HANDLE SOLD SEPARATELY(P/N BY VH1)

STEEL TANKSGallons Sidemount Saddle Upright

10 MH1MHA-3100 - -15 MW1WAS15S - -35 - MW1WAS35S -50 - MW1WAS50S MW1WAS50U70 - - MW1WAS70U

POLYETHYLENE TANKSGallons Sidemount Saddle Upright

50 - - MW1WAP50U

MOUNTING KITS FOR TANKS All kits come with hardware to complete installation. MW1WASMBK Steel Strap for 10, 15, 35, 50 and 70 Gallon Saddle Mount Tanks MW1WASBKSS Stainless Steel Strap

MW1WAP50U Polyethylene Upright

ALUMINUM TANKSGallons Sidemount Saddle Upright

15 MH1MHA-4150 - -35 - MW1WAA35S MW1WAA35U

50 -

MW1WAA50S (With Steel Straps)

MW1WAA50SS (With Stainless Steel Straps)

MW1WAA50U

70 - - MW1WAA70U

CAST IRON SHIFT COVER HOUSING AND STEEL SHIFTING FORK NEARLY ELIMINATE LEAKS AND ENGAGEMENT ISSUES THAT PLAGUE OTHER BRANDS IN THE MARKET.

PTO Sending Unit Wiring HarnessMW1WASWK-699

MW1WA015Replacement Cap

MW1WA091Flange

to Pump Gasket

Two Position Air Toggle Switch MW1WAAIRSWITCH

World American C & G Pumps are known for their ruggedness, reliability and interchangeability. Available in both the 101 Remote Mount and the 102 Direct Mount configurations and C or G frames, these pumps offer cast iron construction, a variety of displacements and “Air Shift” capabilities.

• Bi-Rotational • Pressures up to 3000 psi • Flow rate (GPM) at 1000 rpm • Dual Porting, side and rear, ORB or NPT • Options, 7-Displacements, 2-Shafts, 2-Porting • Universal ports, ports are as large as possible to fit a variety of

applications, use steel adapters to fit your application! We have a full line of adapters to fit your application.

• Bi-Rotational • Pressures up to 3000 psi • Speeds up to 3600 rpm • Flow rate (GPM) at 1000 rpm • Dual Porting, side and rear, ORB or NPT • Combination Mounting Flange, 2/4 Bolt, SAE “B” • Hi-Flow body design for increase flow and performance • Universal ports, ports are as large as possible to fit a variety of

applications, use steel adapters to fit your application! We have a full line of adapters to fit your application.

Walking Floor dual pressure 2000 psi for dump bodies, and 3000 psi for live floor trailers. Pressure switching is controlled from the air supply of the truck. Heavy duty roller bearing construction. Standard with air shift, bracket and mounting hardware.

MW1WAP101-25AS Remote Mount, Air ShiftMW1WAP102-25L Direct Mount w/o Air ShiftMW1WAP102-25LAS Direct Mount with Air Shift

P/N GPM @ 1000 RPMMW1WAK20B8ANX 8MW1WAK20B11ANX 11MW1WAK20B13ANX 13MW1WAK20B15ANX 15MW1WAK20B17ANX 17

P/N GPM @ 1000 RPMMW1WAL51B-19ANX 19MW1WAL51B-23ANX 23MW1WAL51B-25ANX 25MW1WAL51B-27ANX 27

MW1WAWFDPUMP Dual Pressure Pump

MW1WAPBK-1001 6-Bolt Dump Pump Mounting BracketMW1WAPBK-1000 8-Bolt Dump Pump Mounting Bracket

WAK20 Series GPM @ 1000 RPM

WAL51 SeriesGPM @ 1000 RPM

DUMP PUMPS & WALKING FLOOR PUMPS

GEAR PUMPS & MOTORS

IN-LINE RELIEF VALVES

BALL VALVES

HYDRAULIC QUICK COUPLERSWing Nut Style Couplers - Female Matching Nipple - Male Tip

P/N Port Size GPMBY HRV07518 3/4” NPT 20BY HRV10018 1” NPT 30BY HRV10025 1” NPT 50

P/N DescriptionTC 2005-16 1” ball valveTC 2005-20 1-1/4” ball valveTC 2005-24 1-1/2” ball valve

P/N Description

MW1WAF12525 Micron, 25 PSI Bypass

MW1WADFH425 Micron, 25 PSI Bypass

P/N Thread Style Body Size Thread SizeGX QS515W-06 NPF 3/4” 3/4-14GX QS515W-08 NPF 1” 1-11 1/2GX QS515W-10 NPF 1-1/4” 1 1/4-11 1/2

P/N Thread Style Body Size Thread SizeGX QS511-06 NPF 3/4” 3/4-14GX QS511-08 NPF 1” 1-11 1/2GX QS511-10 NPF 1-1/4” 1 1/4-11 1/2

MW1WA925FH • 150 PSI working pressure • Flows up to 50 GPM for return & 15 GPM for suction line applications • Four 1/8” NPT Gage Ports

MW1WADFH4 • 150 PSI working pressure • Flows up to 90 GPM for return and 20 GPM for suction line applications • Both 1-1/2” NPT and 2” SAE Ports

IN-LINE FILTERS

Replacement Filter: LF PH725

Replacement Filter: LF LFP449 (filter sold separately)

Part numbers listed are 7/8" 13 Spline Shaft

SH 550045428 55 Gallon Drum Special OrderSH 550045427 5 Gallon PailSH 550045416 1 Gallon

SHELL TELLUS®/md S2 MX 46 HYDRAULIC OILS

LUC10017 GallonLUC10037 5 Gallon PailLUC10038 55 Gallon Drum Special Order

UNIVERSAL HYDRAULIC FLUID

We recommend a support bracket on all C & G pumps.

MIDWESTWHEEL.COM

IOW

A

MIS

SO

UR

I

DES MOINES1436 E. Ovid Ave.

office 515.265.1491fax 515.265.4120

parts fax 800.314.4329parts 800.888.0248

CEDAR RAPIDS200 50th Ave. S.W.main 319.365.4453fax 319.365.6327

parts fax 877.706.6085parts 800.332.5435

DAVENPORT8502 Northwest Blvd.

main 563.322.2671fax 563.322.5940

parts 800.553.1886

SIOUX CITY1819 4th St.

main 712.252.7969fax 712.252.6149

parts 800.943.3534

CLEAR LAKE840 Hwy. 18 W.

main 641.357.7101fax 641.357.8190

parts fax 800.548.9674parts 800.397.5630

KANSAS CITY5801 E. Front St.

main 816.471.1552fax 816.471.0813

parts 800.821.7402TRUCK PARTS

SUPER STORETM

May 18, 2020 (24PTO and Wet Line Kits)

HYDRAULIC HOSESUCTION/RETURN LINE DESERT™ HR4 LOW PRESSURE HOSESAE 100R4 Meets Flame Resistance USMSHA Designation

P/NHose Size

InchMax. Working

PressureMin. Bend

InchMin. Burst

PSIGX HR4-12X100CL 3/4 300 2.5 1200GX HR4-16X100CL 1 250 3.0 1000GX HR4-20X100CL 1-1/4 200 4.0 800GX HR4-24X100CL 1-1/2 150 5.0 600

Compatible fitting options: • UC fitting w/UCF-6 Collars • Hose barb fittings w/clamps

Application: Low pressure, high temperature return line or suction line for petroleum and water-based hydraulic fluids

Inner Tube: NitrileReinforcement: Spiral-plied synthetic fabric with

wire helixCover: Black neoprene

Temperature Range: -40°F to 275°F Fittings: 2 Piece Crimpable

P/NHose Size

InchMax. Working

PressureMin. Bend

InchMin. Burst

PSIGX XR16SC-04X250RL 1/4 5800 2.0 23200GX XR16SC-06X250RL 3/8 5000 2.5 20000GX XR16SC-08X250RL 1/2 4500 3.5 18000GX XR16SC-10X250RL 5/8 4000 4.0 16000GX XR16SC-12X250RL 3/4 3500 5.0 14000GX XR16SC-16X250RL 1 2700 6.0 10800

Compatible fitting options: • B2 Series crimp fittings

Application: High pressure service with tight bends for petroleum and water based hydraulic fluids. Excellent impulse performance and flexibility exceeding SAE 100R2 and SAE 100R16 standards

Inner Tube: NitrileReinforcement: Two braids of high-tensile steel

wireCover: Black neoprene

Temperature Range: -40°F to 212°F

PRESSURE LINES XR16SC HIGH PRESSURE HOSESAE 100R16/857 2SC Meets Flame Resistance USMSHA Designation • Meets Higher EN/DIN Pressures

We stock a complete line of hose & fittings - Please reference our Continental Hydraulics Catalog for complete details!

GENERAL PURPOSE CLAMPS

P/N Min. Dia. Max. Dia.IDL6506E 51 9/16" 13/16"IDL6508E 51 11/16" 15/16"IDL6510E 51 13/16" 1-1/16"IDL6512E 51 15/16" 1-1/4"IDL6516E 51 13/16" 1-1/2"

LINED CLAMPS

P/N Min. Dia. Max. Dia.IDL47010 51 13/16" 1-1/16"IDL47012 51 15/16" 1-1/4"IDL47016 51 13/16" 1-1/2"IDL47020 51 13/16" 1-3/4"

CONSTANT TORQUE CLAMPS

P/N Min. Dia. Max. Dia.IDL62040 51 7/32" 5/8"IDL62060 51 1/4" 25/32"IDL5706 051 7/16" 25/32"IDL5708 051 1/2" 29/32"IDL5710 051 9/16" 1-1/16"IDL5712 051 11/16" 1-1/4"IDL5716 051 13/16" 1-1/2"

CLOSE NIPPLE

COMBINATION NIPPLE

HEX BUSHING

90° FEMALE PIPE ELBOW

GHD57-140 1-1/2"GHD57-120 1-1/4"

GHDSTC-5 3/4"MW1WABH100 1"MW1WABH125 1-1/4"GHDSTC-20 1-1/2"

GHD65-531 2 x 1-1/2"GHD65-530 2 x 1-1/4"

GHD65-107 1-1/2"GHD65-106 1-1/4"