psi2009 (1)

Pressure Switches, Inc.

1-800-259-687423400 Hwy. 435, Abita Springs, LA 70420

www.pressureswitches.com - [email protected]

Models 1A, 1C, 1D, 1G, 1H, 1P, 1V and 1Z.

Housing per NEMA 4, 4x and 13.

11 amp UL Recognized Microswitch standard. 5 amp UL Recognized Microswitch also available.

Watertight Industrial Connector DIN 43650/IP65. Available also are models with 18 inch freeleads.

Laser Engraved Markings including range scale.

Underwriter Laboratories, Inc. listing file no. E185005 NPKZ - Motor Controllers, Float & Pressure Operated. NKPZ7 - Motor Controllers, Float & Pressure Operated Certified for Canada.

SENSOR MODEL SELECTION TABLE

The differential or deadband fixed and varies with the pressure setting.(1) SEE HOW TO ORDER SECTION

HOW TO ORDER

ELECTRICAL RATINGS (ALL UNITS SPDT)

11A (RES/IND) - 1/4 HP @ 125 OR 250 VAC5A RES, 3A IND @ 28 VDC.5A RES @ 125 VDCOptional: 100mA @ 125 VAC, 0.250A @ 6 VDCAPPLIANCE PLUG

Four pole industrial power connector per DIN43650 specifications, when used with rubber compression gland, offers protection against dust and hosedown conditions (IP 65 Protection Mode). Can be indexed four directions. CSA approved, UL recognized.

P231

FREELEADS

Approximately 18 inch long, 18 AWG UL1015 aapliance wire.

NOTES:1. Piston sensor for high cycling, long life, hydraulic applications.

2. Ambient temperature range is -30F to +160F, -34C to +71C.

3. Polymide for water service 140F (60C) max.

4. For models with 18 inch freeleads, the dimensions are the same less the connector/plug.

5. Specifications and availibilty subject to change without prior notice.

To order a pressure switch that will meet your requirements, specify a model by using the chart below. All configurations may not be immediately available. Consult factory.EXAMPLE: 1G 11 N1 . 43

BASE MODEL

1G 11 N1 43

Fasteners & Exterior covers are stainless steel.

Stainless Steel Pressure Ports available (thru 5000 psi range).

Extremely rugged/precision machined from solid aluminum extrusions/stainless steel bar stock on state of the art CNC lathes and machining centers.

Internal slotted wheel adjustment wheel (for use of screwdriver)

Base Range IDModel Number psig kPa/Mpa psig kPa/Mpa psig Mpa psig Mpa

.01 2-15 14kPa-103kPa 0.2-2.0 1kPa-14kPa 500 3.45 1000 6.89

.03 5-75 34-517 0.5-6.0 3-41 750 5.17 1000 6.89

.43 15-200 103-1.38 2.0-15 14-103 1000 6.89 1250 8.61

.53 50-450 345-3.1 5.0-30 34-207 1500 10.34 3000 20.67

.62 50-1000 345-6.89 10-50 69-345 2000 13.78 5000 34.45

.63 100-1750 689-12.1 15-100 103-689 3000 20.67 5000 34.45

.01 2-15 14kPa-103kPa 0.2-2.0 1kPa-14kPa 500 3.45 1000 6.89

.03 5-75 34-517 0.5-6.0 3-41 750 5.17 1000 6.89

.43 15-200 103-1.38 2.0-15 14-103 1000 6.89 1250 8.61

.53 50-450 345-3.1 5.0-30 34-207 1500 10.34 3000 20.67

.62 50-1000 345-6.89 10-50 69-345 2000 13.78 5000 34.45

.63 100-1750 689-12.1 15-100 103-689 3000 20.67 5000 34.45

1C .64 200-2500 1.3Mpa-17.2Mpa 20-150 138kPa-1.0Mpa 3000 20.67 5000 34.45

.83 400-4000 2.76Mpa-27.6Mpa 75-450 516kPa-3.1MPa 5000 34.5 10000 68.9

.84 500-5000 3.45-34.5 75-500 516.3.4 7500 51.7 10000 68.9

0.71 100-1800 689-12.4 25-125 172-861 5000 34.5 10000 68.9.72 200-2500 1.38-17.2 30-150 207-1 5000 34.5 10000 68.9.73 350-3250 2.41Mpa-22.4Mpa 50-350 345kPa-2.4Mpa 7500 51.7 10000 68.9

0.74 350-4250 2.41-29.3 80-350 551-2.4 7500 51.7 10000 68.9

Max System Proof TestSwitch Adjustment Range Dead Band Approximate

1C

and

1Z

1H

1G

and

1A

1P

Viton 0-Ring Polymide Diaphram

Nitrile 0-Ring Polymide Diaphram

N9 Nitrile 0-Ring SST Piston Teflon Diaphram (P Only)

Viton O-Ring Polymide Diaphram (H Only)

Viton 0-Ring Stainless Steel Diaphram

N1

F1

F2

F6

10 18" Freeleads11 DIN 43650/IP65 Connector42 Terminal Strip For Wiring

Switch Adjustment Range, Choose the range from "Switch Adjustment Range" Column (See Table 1) and enter the range ID Number.

LTR MTL Port SizeA AL 1/2-14 NPTC 316SS 1/4-18 NPTD AL 1/4-18 NPTG AL 1/4-18 NPTH 316SS 1/4-18 NPTP AL 1/4-18 NPTZ 316SS 1/2-14 NPT




Low Pressure Switch For instrumentation type applications:

This Series 1 Pressure Switch is for low and very low pressure requirements, using a sensitive diaphragm sensor with a very narrow deadband. Same standard features of the Series 1.

FOR VERY LOW RANGE INSTRUMENTATIONAPPLICATIONS RANGE ID .12:

Adjustable range: 3” - 100” WC

Deadband: .50” - 3.0” WC

Proof test: 250 PSIG

Typical Model No.: 1G10N1.12 (18” Freeleads)

INSTRUMENTATION AIR PRESSURE SWITCH FOR PNUEMATIC& OTHER APPLICATIONS RANGE ID .14:

Adjustable range: 2 - 16 PSIG

Deadband: 2” WC - .25 PSIG


Typical Model Number: 1G11N1.14(As shown with DIN 43658 / IP65 Connector)

Di�erential Pressure Switch

The Series 1 Differential Pressure Switch is for high pressure and low pressure require-ments. With all the standard features of the Series 1.

Note: Both high and low pressure ports are 1/4-18 NPTF.

TYPICIAL MODEL NUMBERS:1D10F1.02 2-20 PSID W/ 18” FREE LEADSAS SHOWN ABOVE.

1D11F1.04 5-95 PSID W/ DIN 43650/IP65CONNECTOR

1DC10F1.04 5-95 PSID W/ 18“ FREE LEADS AND 316SS PROCESS FITTINGS.

Range ID Number .02 = 2-20 PSID Range

Range ID Number .04 = 5-95 PSID Range

Max System Pressure: 400 PSI

Proof Hi/Lo 1000 PSI

Proof Lo/Hi 1000 PSI

Simultaneous 1000 PSI




Vacuum Switch The Series 1 Vacuum Switch has all the standard features of a Series 1.

Typical Model Numbers:1V10N9.91 - 18” Free Leads

Vacuum Range: 1-28 Inches Hg

Deadband: .75-1.50 Inches HG


Pressure Connection: 1/8-27 NPTF

Terminal Strip

The Series 1 Model 1X42XX.XX Pressure Switch with a termainl strip for wiring and a 1/2-14 NPTF conduit fitting. Available with any range ID including the differential, vacuum and high pressure switches .

Typical Model No.: 1G42N1.03

1V11N9.91 - DIN 43658 / IP65 Connector

Dimensions

Series 1 with “42” Electrical Typical Series 1




Models 2A, 2C, 2G, 2P and 2Z.

Housing per NEMA 4, 4x and 13.

11 amp UL Recognized Microswitch standard. Optional gold plated contacts and 5 amp UL Recognized Microswitch also available.

Watertight Industrial Connector DIN 43650/IP65. Also available are models with 18 inch freeleads, MIL-C-5015 connectors or multi conductor cable.



Laser engraved markings including range scale.

Fasteners are stainless steel.

Models may be factory set, consult factory.

Ambient temperature range: -30F to 160F, -34C to 71C.

Stainless steel pressure ports available.

Extremely rugged/precision machined from solid alminum extrusions/stainless steel bar stock on state of the art CNC lathes and machining centers.

Internal slotted adjustment wheel (for use of screwdriver).

Underwriters Laboratories Inc. listing file no. 185005 for NKPZ - Motor Controllers, Float & Pressure Operated. NKP27 - Motor Controllers, Float & Pressure Operated Certified for Canada.

Base Range IDModel Number psig psig psig Mpa psig Mpa

.01 2-20 0.2-2.0 500 3.45 1000 6.892A .03 5-95 1.0-6.0 750 5.17 1000 6.892C .43 15-200 2.0-15 1000 6.89 1250 8.612G .53 50-450 5.0-30 1500 10.34 3000 20.672Z .62 50-1000 10-50 2000 13.78 5000 34.45

.63 100-1750 20-100 3000 20.67 5000 34.45

.71 100-1800 25-125 5000 34.5 10000 68.9

.72 200-2500 30-150 5000 34.5 10000 68.9

.73 350-3250 50-350 7500 51.7 10000 68.9

.74 400-4500 80-350 7500 51.7 10000 68.9

103-1.38345-3.1345-6.89689-12.4

2P 345kPa-2.4Mpa2.76-31.1 551-2.4

689-12.4 172kPa-861MPa1.38-17.2 207-1.0

2.41Mpa-22.4Mpa

14-10334-20769-345137-689

Max System Proof Test

14kPa-137kPa34-655

1kPa-14kPa6.8-41

Switch Adjustment RangekPa/Mpa

Dead Band ApproximatekPa/Mpa




HOW TO ORDERELECTRICAL RATINGS (ALL UNITS SPDT)

11A (RES/IND) - 1/4 HP @ 125 OR 250 VAC5A RES, 3A IND @ 28 VDC.5A RES @ 125 VDCOptional: 100mA @ 125 VAC, 0.250A @ 6 VDC

APPLIANCE PLUGFour pole industrial power connector per DIN43650 specifications, when used with rubber compression gland, offers protection against dust and hosedown conditions (IP 65 Protection Mode). Can be indexed four directions. CSA approved, UL recognized.

P231

FREELEADS

Approximately 18 inch long, 18 AWG UL1015 aapliance wire.

DIMENSIONS

1. Piston sensor for high cycling, long life, hydraulic applications.

2. Polymide for water service 140F (60C) max.

3. Internal adjustment with laser engraved range scale.

4. Shipping weight approx. 1lb. min.

NOTE:

To order a pressure switch that will meet your requirements, specify a model by using the chart below. All configurations may not be immedi-ately available. Consult factory.

EXAMPLE: 2P 10 N9 . 71

2P 10 N9 71

MULTI CONDUCTOR CABLE

Multi conductor cable UL 22464, CSA T-1 18 AWG PVC insulated per UL 1007, secured with a nylon liquid tight (dome fitting) connector. Protection class IP 68 per DIN 40050, UL Listed, CSA and VDE certified. Color code laser marked on switch.

(.X) OPTIONS.1 MS33649-4 Pressure Fitting.2 Gold Contact Microswitch.5 5A Microswitch.B Base bracket for mounting

10 18" Freeleads11 DIN 43650/IP65 Connector

16Liquid Tight Connector W/Multi Conductor Cable

52 MS 3102R 12S-3P {2PIN}53 MS 3102R 14S-7P {3PIN}





N1

F1

F2


LTR MTL Port SizeA AL 1/2-14 NPTC 316SS 1/4-18 NPTG AL 1/4-18 NPTP AL 1/4-18 NPTZ 316SS 1/2-14 NPT




The PSI ‘Hardhat Series’Models 6A, 6C, 6G, 6H, 6P and 6Z.

Explosion proof and weatherproof switch enclosure is LISTED for hazardous areas.

Field adjustable set point without opening the snap-switch cover.

Internal slotted adjustment wheel can be adjusted with screwdriver blade.

All markings including range scale are laser engraved.

Stainless steel pressure port available.

Stainless steel fasteners.

Gold plated snap-switch(es) are standard.



The Series 6 Pressure Switch is a highly reliable pressure switch for tough applications. Its precision machined aluminum body is anodized for maximum corrosion protection. A polymide film diaphragm operates a field adjustable switch trip point mechanism attached to a long mechanical life, sensitive differential snap-switch(es), except the 6P where a piston replaces the diaphragms.

All models are weatherproof rated NEMA 4 and 4X, as well as NEMA 7 and 9 for hazardous areas. Models carry Underwriters Laboratories and CSA listing. Pressure ports are availiable in either anodized aluminum or stainless steel, which are through the 5000 psi range.

DESCRIPTION APPLICATIONSGas Compressors

Pumps

Water and Waste Water

Air

Hydraulics

Chemical Processing

Base Range IDModel Number psig psig psig Mpa psig Mpa

.01 2-15 0.2-2.0 500 3.45 1000 6.89

.03 5-75 0.5-6.0 750 5.17 1000 6.89

.43 15-200 2.0-15 1000 6.89 1250 8.61

.53 50-450 5.0-30 1500 10.34 3000 20.67

.62 50-1000 10-50 2000 13.78 5000 34.45

.63 100-1750 15-100 3000 20.67 5000 34.45

.01 2-15 0.2-2.0 500 3.45 1000 6.89

.03 5-75 0.5-6.0 750 5.17 1000 6.89

.43 15-200 2.0-15 1000 6.89 1250 8.61

.53 50-450 5.0-30 1500 10.34 3000 20.67

.62 50-1000 10-50 2000 13.78 5000 34.45

.63 100-1750 15-100 3000 20.67 5000 34.456C .64 200-2500 20-150 3000 20.67 5000 34.45

.83 400-4000 75-450 5000 34.5 10000 68.9

.84 500-5000 75-500 7500 51.7 10000 68.96P .73 350-3250 50-350 7500 51.7 10000 68.9

6Gand6A

2.41Mpa-22.4Mpa

103-1.38

103-1.38345-3.1345-6.89689-12.1

345kPa-2.4Mpa

6Cand6Z

1.3Mpa-17.2Mpa 138kPa-1.0Mpa

6H 2.76Mpa-27.6Mpa 516kPa-3.1MPa3.45-34.5 516-3.4

345-6.89 69-345689-12.1 103-689

14-103345-3.1 34-207

14kPa-103kPa 1kPa-14kPa34-517 3-41

14-10334-20769-345

103-689

Max System Proof Test

14kPa-103kPa34-517

1kPa-14kPa3-41

Switch Adjustment RangekPa/Mpa

Dead Band ApproximatekPa/Mpa




HOW TO ORDERSPECIFICATIONSNOWT: Boat and pressure operated motor controllers, for use in hazard-ous locations.

Listed by: Uderwriters Laboratories Inc. (File No. E123884) suitable for: Class I, Div. 1, Groups A, B, C, D; Class II, Div. 2, Groups E, F, G.

Maximum ambient and service temperature range: -30F to 160F (-34C to 71C). Note: Polymide for water service 140F (60C) maximum.

Series 6 - LOW PRESSURE SWITCH

DESCRIPTION:FOR INSTRUMENTATION APPLICATIONS.The Series 6 Pressure Switch is for low and very low requirements using a sensitive diaphragm sensor with very narrow dead-bands, with all the standard features of the Series 6 with UL listing for Hazardous Areas.

DIMENSIONS

To order a pressure switch that will meet your requirements, specify a model by using the chart below. All configurations may not be immedi-ately available. Consult factory.

EXAMPLE: 6G 12 F1 . 03

6G 12 F1 03

Certified by CSA: Cert. file No. LR76122-1 Class I, Div. 1 Groups B, C, D; Class II, Div. 2 Groups E, F, G. Class 3238 01 - Switches-Automatic-Pressure Type for Hazardous Loca-tions.

Snap switch ratings:SPDT (gold): 100mA @125 VAC; 0.250 A @ 6 VDC.DPDT (gold, 2 microswitches): 100mA @125 VAC; 0.250 A @ 6 VDC.

Internal ground screw clamp.

FOR VERY LOW RANGE INSTRUMENTATION APPLICATIONS RANGE ID: .12.

INSTRUMENTATION AIR PRESSURE SWITCH FOR PNEUMATIC AND OTHER APPLICATIONS RANGE ID: .14. Adjustable range: 3.0” - 100” WC

Deadband: .50” - 3.0” WC (Approx.)Proof Pressure: 250 PSIGTypical model number: 6G12N1.12

Adjustable range: 2-16 PSIGDeadband: 2” WC - 0.25 PSIG (Approx.)Proof Pressure: 250 PSIGTypical model number: 6G12N1.14

*Wetted materials.

* *

Specifications and availibilty subject to change without prior notice.

Weight: Approx. 40 oz (1.13 kg) min. SEE HOW TO ORDER

LTR MALT Port SizeA AL 1/2-14 NPTC 316SS 1/4-18 NPTG AL 1/4-18 NPTH 316SS 1/4-18 NPTP AL 1/4-18 NPTZ 316SS 1/2-14 NPT

12 SPDT (Gold STD.)33 DPDT (Gold STD.)




Viton O-Ring Polymide Diaphram (H Only)


N1

F1

F2

F6


psi2009 (1)

Documents

Transcript of psi2009 (1)