Promoting Science and Education through High Altitude Balloons and Amateur Radio eoss
description
Transcript of Promoting Science and Education through High Altitude Balloons and Amateur Radio eoss
Promoting Science and Education through High Altitude Balloons and Amateur Radio
www.eoss.org Low-cost Payload Design ConsiderationsLow-cost Payload Design Considerations
Low-Cost Access to Near Space WorkshopSouthwest Research Institute, Boulder CO,
26 April 2007
Mike Manes, President [email protected]
What Is EOSS?
Founded January 1991 as a Colorado scientific & educational non-profit corporation 501(c)(3)
Funded by donations and 60+ volunteer members 117 flights to date with 100% payload recovery record Charter:
– Promoting Science and Education Through Amateur Radio and High Altitude Balloons
“The Poor Man’s Space Program”– Payloads to Near Space for $200 to $500
– Provide students hands-on experience with science and technology to the edge of of space
– Provide near space transport and recovery for scientific experiments
Key economies of high-altitude balloon flight
Lowest cost access to Near Space Feasible for vertical integration by small organizations
– Operational simplicity
– Commercial availability of balloons, fill gas and payload materials
– Free / low cost forecasting, tracking utilities
– Support by peer non-profits
– Local launch site and scheduling mitigates travel costs
» Launch with short notice of suitable trajectory & weather
» Launch site should be selected to avoid risks to the public, but can be little more than a wide spot in the road.
» Coordination and cooperation with FAA is important when operating in civil airspace (CFR 14 Part 101)
Most important economic factor: Payload Recovery
Top-level design considerations
“Things should be made as light as possible, …
Launch costs vary directly with payload weight “Payload weight” excludes 2 – 4 kg flight system
components necessary for recovery:– 0.7 – 2.0 kg parachute
– 0.8 – 1.7 kg GPS telemetry beacon
– 0.5 kg DF beacon / cutdown command receiver
Payload weight drives balloon selection
Expendables costs: Plastic vs. Latex
Balloon expendibles cost vs. Payload weight1000 fpm to 100,000 ft MSL apogee
$0
$500
$1,000
$1,500
$2,000
$2,500
$3,000
0.0 50.0 100.0 150.0 200.0
Payload wt, lb(assumes 4.3 lb beacons & parachute)
Co
st,
US
$
Latex
Plastic
Balloon type selection
Latex balloon pros:– Lowest cost
– Lightest weight
– Simple prep and fill process
– Multiple commercial sources
– Self destructs & biodegrades
Latex balloon cons:– Limited to 12 kg max payload
– +/- 10% apogee uncertainty
– Loiter valving still developmental
– Flight duration limited by UV degradation
Plastic balloon pros:– Required for > 12 kg
– Required for loiter missions
– Long duration flights feasible
» ballast dumps on ZP
» super-pressure envelope
Plastic balloon cons:– Costly (base price > US$400)
– Envelope film is heavy and fragile
– Complex prep and fill process
– Single domestic source (Raven)
– Redundant destruct devices required
– Used envelope is livestock hazard
Plastic balloon fill
54,000 cu ft Raven top fill burster
Latex balloon fill
3000 gm Totex with 10 kt surface wind
Latex balloon expendables
Latex balloon expendibles vs. Payload weight1000 fpm to 100,000 ft MSL apogee
$0
$50
$100
$150
$200
$250
$300
$350
$400
$450
$500
0.0 5.0 10.0 15.0 20.0 25.0 30.0
Payload wt, lb(assumes 4.3 lb beacons & parachute)
Co
st,
US
$
Flight environment considerations
“… but not more so.” (Apologies to A. Einstein)
Payload structures and flight string must survive environmental rigors:– Launch jerk: 0 to 5 m/sec in 0.1 sec.
– Air temperatures down to -80ºC at tropopause
– Barometric pressure < 10 mbar (poor thermal convection)
– Strong solar flux, especially UV (IR help thermals)
– High initial descent rates > 100 m/sec
– Parachute instability (Post-burst chaos)
– Parachute drag upon windy landing
Some flight environments …
… can’t be designed for.
Payload line design methodologies
Consider string of small payloads vice single integrated package– GPS telemetry beacons can upset analog, fast digital electronics
– Multiple experiments can share a flight w/o integration headaches
– Use wireless LAN to link separate payloads in lieu of cable
Use low modulus payload cordage to absorb shock– MIL-C-7515E woven nylon is preferred (50% stretch to yield)
» 250# tensile minimum, 500# for > 6 kg strings
– Dacron core, Kevlar may transmit shock > tensile strength
– Allow plenty of slack on parallel electrical conductors, antennas
Use low-stress “marlinspike seamanship”– Double bowline is strong & unties easily
– Figure 8 knot is lower stress than half hitch
Multiple payload launch
Payload package materials & methods
Foamcore board structures with thru-tube support– Low-cost “honeycomb” available from art, big box stores
– Easily formed to < 0.5mm tolerances using hand tools, hot-melt glue
– 8mm foamcore provides adequate thermal insulation for most payloads
– With thin coat of acrylic spray paint, resists UV. moisture & shock
– Thru-tube isolates support line tension from enclosure structure
– With sound design, expect over 20 flights
Building sheet insulation and closed-cell HDPE– Superior thermal insulation and shock resistance
– Low precision dimensions
– 3D cavities difficult to form
Off-the-shelf (or dumpster)– Workable, but sizing is inflexible.
Some EOSS payloads
Design for Recovery
A significant operational economy– Payload reuse, refurb, modification– On-board data storage eliminates telemetry cost, weight, EMC
On-board data storage – Onset Computing “Hobo” loggers are lightweight, easy to use– Flash memory up to 2 Gbytes is suitable for bulk data, imaging– Sample species in situ & store on board for later analysis
» NOAA “Aircore” profiler» CU bacteria sampler
Supply at least 24 hr battery power to beacons– LiSO2 primary cells have excellent energy density, low temp operation– Available at low cost on surplus market
Recovery requires GPS telemetry, RDF, mobile skills– Amateur radio is a useful tool
Command & Telemetry radios
Amateur radio VHF & UHF bands for CMD/TLM and GPS tracking– Only option if gov’t frequencies not provided; Part 15 range is too
short
– Also useful for coordination amongst launch, recovery teams
– Ham license required, but exam by volunteers and no Morse required
– FCC Part 97 prohibits commercial use, but support of science, education is OK.
– Internet gating to findu.com deemed essential by some FAA offices
GMRS & FRS– Limited frequency selection and range
– Possible alternative to ham radio, but not compatible with findu.com
Launch site communications
Tracking Operations
– Trajectory forecasting and launch site selection
– Track and recovery team deployment around
forecast landing site before launch
– Tracking team coordination via radio net on UHF
repeaters
Skilled trackers beat payload to landing site
Prime directive:No Trespassing!
Locate land owners, obtain permission to enter property
Most owners are happy to join in
Another successful recovery
…And the students arrive!
Plastic envelope recovery
Separate tracking and recovery from main payload string
Separate GPS & DF beacons required, along with termination devices
Recent & emerging technical developments
Payload electronics– Low power, inexpensive microprocessors– High capacity non-volatile memories– Low cost digital cameras & DVRs– Part 15 wireless LAN amongst payloads, flight system– Lithium battery advances
Tracking technologies– VHF RDF triangulation made way for Loran-C and now GPS– Automated relay of APRS downlink to internet & to FAA controllers
Recovery techniques– Ground & air search for DF beacon replaced by real-time GPS tracking
displayed on ground mobile laptops– Computerized trajectory forecasting using sophisticated NOAA
models yields visual observation of landing– Steerable / homing descent emerging to replace common parachutes
Any questions?