Progress 03 - Design · Design Tubes First, I drew the boundaries on Rhinoceros and everything that...
Transcript of Progress 03 - Design · Design Tubes First, I drew the boundaries on Rhinoceros and everything that...
![Page 1: Progress 03 - Design · Design Tubes First, I drew the boundaries on Rhinoceros and everything that go inside it can be use for 3D laser printing (285 x 150 x 150 mm). Then, I drew](https://reader033.fdocuments.net/reader033/viewer/2022042316/5f056cd07e708231d412e642/html5/thumbnails/1.jpg)
Progress 03 - DesignBy Vicky Lai
![Page 2: Progress 03 - Design · Design Tubes First, I drew the boundaries on Rhinoceros and everything that go inside it can be use for 3D laser printing (285 x 150 x 150 mm). Then, I drew](https://reader033.fdocuments.net/reader033/viewer/2022042316/5f056cd07e708231d412e642/html5/thumbnails/2.jpg)
Design Marker/Pen HolderFirst, I measured the dimension of different circles and tubes from the prototype we made before.
![Page 3: Progress 03 - Design · Design Tubes First, I drew the boundaries on Rhinoceros and everything that go inside it can be use for 3D laser printing (285 x 150 x 150 mm). Then, I drew](https://reader033.fdocuments.net/reader033/viewer/2022042316/5f056cd07e708231d412e642/html5/thumbnails/3.jpg)
Secondly, based on the measurements I made, I tried to design the pen holder on Rhinoceros for the first time. I realise
what I did is not legit. The smaller circle was not placing correctly on the center of the biggest circle. And there were
many small circles were out of place.
![Page 4: Progress 03 - Design · Design Tubes First, I drew the boundaries on Rhinoceros and everything that go inside it can be use for 3D laser printing (285 x 150 x 150 mm). Then, I drew](https://reader033.fdocuments.net/reader033/viewer/2022042316/5f056cd07e708231d412e642/html5/thumbnails/4.jpg)
Next, I found an online exercise on to draw a 2D object on Rhinoceros, so I can get an idea of how this program works.
I used many simple shapes to create a more complex object.
URL: http://www.aversis.be/tutorials/rhinoceros/rhino_2d_drawing.htm
![Page 5: Progress 03 - Design · Design Tubes First, I drew the boundaries on Rhinoceros and everything that go inside it can be use for 3D laser printing (285 x 150 x 150 mm). Then, I drew](https://reader033.fdocuments.net/reader033/viewer/2022042316/5f056cd07e708231d412e642/html5/thumbnails/5.jpg)
Lastly, I re-made the modeling of the pen holder after I learn more about Rhipcerors. It is much accurate compare to
the first model I drew. I also wrote the radius of all circles and the distance between them, which helped me to double
check with the prototype.
![Page 6: Progress 03 - Design · Design Tubes First, I drew the boundaries on Rhinoceros and everything that go inside it can be use for 3D laser printing (285 x 150 x 150 mm). Then, I drew](https://reader033.fdocuments.net/reader033/viewer/2022042316/5f056cd07e708231d412e642/html5/thumbnails/6.jpg)
Alpha Laser CuttingI brought my file to the laser room and had them cut in the laser cutting machine.
![Page 7: Progress 03 - Design · Design Tubes First, I drew the boundaries on Rhinoceros and everything that go inside it can be use for 3D laser printing (285 x 150 x 150 mm). Then, I drew](https://reader033.fdocuments.net/reader033/viewer/2022042316/5f056cd07e708231d412e642/html5/thumbnails/7.jpg)
Design TubesFirst, I drew the boundaries on Rhinoceros and everything that go inside it can be use for 3D laser printing (285 x
150 x 150 mm). Then, I drew a solid cylinder with dimension 5mm and length 75mm. I shorten the length of the
tube compare the prototype we had in progress 01 & 02 from the feedback. Bases on the feedback, shorter
length of the tube is easier to balance and stabilise the marker/pen. I made two copies of the cylinder that I drew,
so they are all identical.
![Page 8: Progress 03 - Design · Design Tubes First, I drew the boundaries on Rhinoceros and everything that go inside it can be use for 3D laser printing (285 x 150 x 150 mm). Then, I drew](https://reader033.fdocuments.net/reader033/viewer/2022042316/5f056cd07e708231d412e642/html5/thumbnails/8.jpg)
![Page 9: Progress 03 - Design · Design Tubes First, I drew the boundaries on Rhinoceros and everything that go inside it can be use for 3D laser printing (285 x 150 x 150 mm). Then, I drew](https://reader033.fdocuments.net/reader033/viewer/2022042316/5f056cd07e708231d412e642/html5/thumbnails/9.jpg)
3D PrintingI brought my file to the laser room and had them print by the 3D laser printing machine. I waited for around 30 to
40mins to get it printed. I also sanding these tubes to make it more smooth outside.
![Page 10: Progress 03 - Design · Design Tubes First, I drew the boundaries on Rhinoceros and everything that go inside it can be use for 3D laser printing (285 x 150 x 150 mm). Then, I drew](https://reader033.fdocuments.net/reader033/viewer/2022042316/5f056cd07e708231d412e642/html5/thumbnails/10.jpg)
AssemblingI put assembled the component I made to make a pen holder.
![Page 11: Progress 03 - Design · Design Tubes First, I drew the boundaries on Rhinoceros and everything that go inside it can be use for 3D laser printing (285 x 150 x 150 mm). Then, I drew](https://reader033.fdocuments.net/reader033/viewer/2022042316/5f056cd07e708231d412e642/html5/thumbnails/11.jpg)
Sketching PulleysI sketched some basic idea of how to design a pulley that can
rolling strings that attached to the pen holder and how pulleys
attached to servo motors. One side of the pulley is thicker
than the other side, so I can screw the pulley onto the motor. I
will continuously refine and design a perfect fit of pulleys for
the motors we are going to use.
![Page 12: Progress 03 - Design · Design Tubes First, I drew the boundaries on Rhinoceros and everything that go inside it can be use for 3D laser printing (285 x 150 x 150 mm). Then, I drew](https://reader033.fdocuments.net/reader033/viewer/2022042316/5f056cd07e708231d412e642/html5/thumbnails/12.jpg)
Video
Making Circles Making Tubes