PROGRAMMING MANUAL FOR UNDERPLASTER RADIO … · 1 Production plant in Opole Technical...
Transcript of PROGRAMMING MANUAL FOR UNDERPLASTER RADIO … · 1 Production plant in Opole Technical...
1
PROGRAMMING MANUAL FOR UNDERPLASTER RADIO CONTROLLER AL-RSP 01
Production plant in Opole
ul. Gosławicka 3, 45-446 Opole, Poland
tel: +48 77 40 00 000, fax. +48 (77) 40 00,006
e-mail: [email protected]
Headquarters; Production plant in Bielsko-Biała
ul. Warszawska 153, 43-300 Bielsko-Biała, Poland
tel: +48 33 81 95 300, fax. +48 33 82 28 512
- power supply: 230 VAC / 50 Hz, - transmission frequency: 433.92 MHz, - transmission power: 10 milliwatt (mW), - operating temperature: ~ 0OC to +45OC, - controlling of the motor or two light circuits, - installation in standard flush box, - transmission distance: 200 metres (open area) 35 metres (built-up area) . Works only with motors without built-in radio control.
Works with all transmitters from DC series offered by ALUPROF S.A.
(excluding transmitter DC 115B).
The manufacturer reserves the tolerance of catalogue data due
to use in different conditions.
Technical specification
Wiring diagram
In accordance with the provisions of the Directive of the European Parliament and the Council 2012/19/UE of 4 July 2012 on waste electrical
and electronic equipment (WEEE), it is prohibited to place together with other wastes used equipment marked with the symbol of crossed
out bin. The user is obliged to transfer used equipment to a designated collection point for proper processing. The marking means that at
the same time the equipment was launched on the market after 12 August 2005. Above legal obligations have been introduced to reduce
the amount of waste generated from waste electrical and electronic equipment and to ensure an appropriate level of collection, recovery
and recycling. No harmful components, which have a particularly negative impact on the environment and human health are included in
the equipment components.
NOTE
- Installation of the radio control should be carried out by authorized persons.
- The radio control is designed for use in dry rooms and should not be exposed to direct weather conditions.
- The radio control should be powered by a separate circuit and protected by a quick fuse for example: circuit breaker type B10.
Motor wiring diagram Lighting circuit wiring diagram
2
Change of work mode
OK
The LED flashes twice in the current mode colour and then twice in the colour of the new
mode
While the power supply is ON press 5x the programming button PROG,
which will be confirmed by LED lightning
RED COLOUR Mode of roller shutter operation
GREEN COLOUR Mode of lightning control
operation
I - Mode of roller shutter operation
1. Programming of the first transmitter
By turning on power supply
The transmitter has been programmed
Turn on the power, which will be confirmed by the UP-DOWN
movement
OK
In the interval of two seconds press the “P2” button twice,
which will be confirmed by the UP-DOWN movement
Press the “UP” button, which will be confirmed by the UP-DOWN
movement
Using the programming button
The transmitter has been programmed
While the power supply is ON press 3x the programming button PROG,
which will be confirmed by LED lightning
OK
In the interval of two seconds press the “P2” button twice,
which will be confirmed by the UP-DOWN movement
Press the “UP” button, which will be confirmed by the UP-DOWN
movement
Using the two-way switch
The transmitter has been programmed
While the power supply is ON
quickly 3x press the button “UP” or “DOWN” on the switch, which will
be confirmed by the UP-DOWN movement
OK
In the interval of two seconds press the “P2” button twice,
which will be confirmed by the UP-DOWN movement
Press the “UP” button, which will be confirmed by the UP-DOWN
movement
3
Press twice the button “P2” of the already programmed transmitter, which will be confirmed by the UP-DOWN movement
Press the button “P2” of the new transmitter, which will be confirmed by the UP-DOWN
movement
The new transmitter has been
programmed.
2. Adding an additional transmitter
OK
3. Deleting transmitter
OK
Press the “P2” button, which will be confirmed by the UP-DOWN
movement
Press the “STOP” button, which will be confirmed by the UP-
DOWN movement
Press the “P2” button, which will be confirmed by the UP-DOWN
movement
The transmitter has been deleted
II - mode of lightning control operation
4. Programming of the first transmitter
By turning on power supply
The transmitter has been programmed
Turn on the power, which will be confirmed by applying voltage to
the output W1 and W2
OK
In the interval of two seconds press the button “P2”
(1xP2 for W1, 2xP2 for W2), which will be confirmed by
applying brief voltage pulses to the output W1 or W2
Press the button “UP”, which will be confirmed by applying voltage
to the output W1 or W2
Using the programming button
The transmitter has been programmed
While the power supply is ON press 3x the programming button PROG,
which will be confirmed by LED lightning
OK
In the interval of two seconds press the button “P2”
(1xP2 for W1, 2xP2 for W2), which will be confirmed by
applying brief voltage pulses to the output W1 or W2
Press the button “UP”, which will be confirmed by applying brief
voltage pulses to the output W1 or W2
4
Using the two-way switch
The transmitter has been programmed
While the power supply is ON
quickly 3x press the button “UP” or “DOWN” on the switch, which will
be confirmed applying voltage to the output W1 and W2
OK
In the interval of two seconds press the button “P2”
(1xP2 for W1, 2xP2 for W2), which will be confirmed by
applying brief voltage pulses to the output W1 or W2
Press the button “UP”, which will be confirmed by applying brief
voltage pulses to the output W1 or W2
Press the button “P2” of the already programmed transmitter, which will be
confirmed by applying brief voltage pulses to the output W1 or W2
Press the button “P2” of the new transmitter, which will be confirmed by applying brief voltage
pulses to the output W1 or W2
The new transmitter has been
programmed.
5. Adding an additional transmitter
OK
While the power supply is ON press 7x the programming button PROG,
which will be confirmed by LED lightning
The led will turn colour green - red - green
All transmitters have been deleted
The LED will turn red, which will be confirmed by applying brief voltage pulses to the output
W1 or W2 (the motor performs movement up - down)
OK
6. Deleting selected transmitter
OK
Press the button “P2”, which will be confirmed by applying brief
voltage pulses to the output W1 or W2
Press the button “STOP”, which will be confirmed by applying
brief voltage pulses to the output W1 or W2
Press the button “P2”, which will be confirmed by applying brief
voltage pulses to the output W1 or W2
The transmitter has been deleted
7. Return to the factory settings
The procedure of returning to factory settings is identical for both working modes and removes all transmitters programmed in the control unit