PROFESSIONAL BAR SETUP GUIDE · 2019. 10. 9. · STEP 2: Pull up the acrylic panel. Side Panel STEP...
Transcript of PROFESSIONAL BAR SETUP GUIDE · 2019. 10. 9. · STEP 2: Pull up the acrylic panel. Side Panel STEP...
Table of contents:- Part List- Set Up Guide
PROFESSIONAL BAR SETUP GUIDE
Note: Two persons required to setup this bar.
• Read all the instructions before installing.
• Remove all packing materials before you start.
• This installation requires basic mechanical skills.
• Proper installation is responsibility of the installer.
• Product failure due to improper installation is not covered under the warranty.
• Keep this instruction manual.
2 BEFORE YOU BEGIN THE INSTALLATION
Main FrameQTY: 1
Speed RailQTY: 1
Ice BinQTY: 2
Lock PinQTY: 2
Note: Parts are not to scale.
Acrylic PanelQTY: 4
Cutting BoardQTY: 2
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
3PART LIST
Front AcrylicSide Acrylic
Counter Acrylic
x2
CoverQTY: 1
ThumbscrewsQTY: 2
Magnet SquaresQTY: 2
Cup Holder
KnifeHolder
PaperTowelHolder
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
Note: All accessories attach with provided M6 screws and allen wrench.
PROFESSIONAL BAR ACCESORIES4
STEP 1: Remove the counter top and speed rail.
STEP 2: Release the bottom grill by detaching the security hook.
STEP 3: Swing open side frames to set it in place.
STEP 4: Secure the side frames in place using two locking pins, one on each frame.
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
Figure 1
Figure 2
1
2
3
Figure 3
Figure 4
P1
P2
P1
PROFESSIONAL BAR ASSEMBLY SET UP STEPS 5
DANGER: USE CAUTION WHEN MOVING THE SIDE FRAMES TO AVOID DROPPING
CAUTION: BOTTOM GRILL WILL DROP DOWN AS YOU RELEASE THE HOOK
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5: Flip the shelf up and lock it into place using the spring
latches: and .P3 P4
STEP 6: Flip the work surface and lock it into place using the
spring latches and .P5 P6
STEP 7: Place the icebins.
STEP 8: Place the counter top. Then lock it in place using the
spring latches and . Rest the acrylic piece on top of the counter.
P7 P8
Figure 5
Figure 7
STEP 9: Hang the speed rail from the 3 posts located at the front tube of the top shelf, as shown below:
Note: The positions of the cutting board and the ice bins are interchangeable
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
P3
P4
Figure 6
P5
P6
Figure 9
Figure 8
P7
P8
PROFESSIONAL BAR ASSEMBLY SET UP STEPS6
STEP 5 STEP 7
STEP 6
STEP 8
STEP 9
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
Folded
Unfolded
PROFESSIONAL BAR ASSEMBLY SET UP STEPS 7
Note: Remember to put down the levelers before folding the bar.
Back Panel
STEP 1: Remove screws and . Then remove the tab as shown below.
S1 S2
STEP 2: Pull up the acrylic panel.
Side Panel
STEP 1: Remove screws , , and . Then remove the side frame as in the next step.
S3 S4 S5 S6
Top Panel
STEP 1: Underneath the counter you’ll find two holes from where you can push the acrylic up.
S3
S4
S5
S6
STEP 2: Once up, take out the acrylic.
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
S1
S2
PANELS SETUP STEPS8
Figure 12
Figure 13
Figure 14
Figure 10
Figure 11
Note: Store acrylic counter in pocket of folded cover when not in use
STEP 2: Slide out the side panel.
Figure 15
Note: Follow setup steps in reverse order to fold down the bar.
Note: Follow setup steps in reverse order to fold down the bar.
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
Use provided thumbscrews to connect multiple counters. Run each thumbscrew through the holes in the side and fully tighten.
PROFESSIONAL BAR 9
The included magnet squares are to cover the holes on the under side of the counter, as shown. These are intended to block light from the LED system or other light sources when applicable.
Contact usTel # 877-958-7901Fax # 866-659-3353E-mail: [email protected]
Visit us atwww.theportablebarcompany.com
PROFESSIONAL BAR CURVED COUNTER SETUP GUIDE - 01/2019