Procedure to Download Software via Tftp in Nehc

PROCEDURE TO DOWNLOAD SOFTWARE VIA TFTP IN NEHCLITESPAN FR3.0 ANETO

1.- First at all we need to know we are going to use several interfaces for this download, in NEHC and in LIOC card, basically we are going to use Probe to start TFTP application and we need the LAN interface in LIOC card to download the software.

Debug Connection (Probe) Parameters: 38400, N, 8, 1, No Flow Control

Connection Ethernet Parameters: Check in the Installation Data that TCP/IP protocol is configured (not OSI protocol) , and note that Ethernet Interface of our PC must belongs to the same subnet of the IP Address management (we can use any sniffer to checks the outgoing packets from this interface)

for example:

Installation Data: ******************Line Subrack Cap= MLS3FCountry = GenericLocation Type = 3F Indoor RackQ3_MAC_TYPE = IP Ethernet

IP Address= 192.168.1.1IP Deg Gat= 192.168.1.2Subnet Mask 255.255.255.0

. . . . . . . .

. .

. . . . . . . .

. .

2.- Then, we need to download the software we are going to transfer to the PC that we are going to use as FTFP server.

In this example we are going to use version 30.0.5

COREcomp30.0.5.tar FW_TOOLS.tar

2.- Then we create a folder that is going to be the root directory for the TFTP server and extract all the files included in two previous files into this one, in our example we are creating folder aneto in D drive (D:\ temp2.

3.- Then we start the TFTP application in the pc, in our case we have choosen 3EC daemon software but any other application will work as well. In 3EC daemon we configure the root directory where the software is located.

i.e. Upload/Download directory: d:/temp (este será el directorio de trabajo del TFTP server)

4.- Finally we need to define an IP address in our local connection in order to have IP connectivity with the interface we are going to define in LIOC.

Por ejemplo: Según el Installation Data: IP = 192.168.1.1Entonces, la IP de la Pc Local = 192.168.1.10

5.- Once we have our PC configured, we need to perform the connection to the NEHC via debugging (Probe) and stop the board if it´s started.

Para entrar en los parámetros hay que hacer: PROBE+/ tftp –v

MAC Addres default = 12234567789aInternal IP Address = 192.168.1.9

6.- The download is performed, we can see there are three phases, one for the download (represented as ****), another one for erasing ) represented as ______,

and the last one for writing in memory (represented as ####). These phases will be repeteaded for every packet in the software.

7.- At the end of the procedure, the system will ask about continuing the tftp procedure. We must answer “no” and the system will reboot and start-up with the new software.

A continuación, se muestra un ejemplo:

Initialating PROBE

Initialating PNA

NEHCB BOOT START RUNNING IN FR 2.8.-------------------------------------

Seed Version : NEHCSEED4.0.2Seed Date : 20 Jan 2007Seed Selection : Bank A Runnig Boot : Bank A. Boot Version : NEHCBOOT4.0.6Boot Date : 29 Jan 2007

Software Watchdog Reset : [Active]Very best copy with Watchdog Reset : [Active]Very best copy with Reset Buttom : [Active]Checksum Check : [Active]MPC885 Part number : 0x12.MPC885 Mask number : 0x0.Clock Frequency : 66 MHz.Active Boot Bank & Active Ata Bank Joined

Loading FPGA's code from first application bank 0x12040000.FPGA DOWNLOAD IS OK.Reset Reason (RSR): 0xc0 => Power On ResetLast Program Counter : [0x1180000].

Loading Program from Application bank to RAM. Waiting...Active Boot Bank & Active Ata Bank Joined

Application Version:

SWD-PD-R2.7

V30.0.3

Download from bank 0. address 10800000. Size 48a62d*****Code is Compressed with CX Algorithm.Decompressing code from address 1e7a99c ... Application Code has not been executed. Checksum is skipped.

boot execution time: 13.890 seconds

FPGA IS RUNNING VERSION 20.

pROBE+/PPC PS V3.1.1pROBE+/PPC CE V3.1.1pROBE+/PPC QS V3.1.1pROBE+/PPC DI V3.1.1

pROBE+>tftp -v

TFTP Client ready to be executed in vervose mode.pROBE+> gs Kernel Event Break Running: 'ROOT' -#00020000 ------------------------------------------------------------------------------pSOS Initialized Event------------------------------------------------------------------------------CR =00000000 XER=00000000 LR =DEADDEADCTR=00000000 MSR=00001032R0 =00000000 0230D100 01A012C0 00000000 00000000 00000000 00000000 00000000R8 =00000000 00000000 00000000 00000000 00000000 01A012A4 00000000 00000000R16=00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000R24=00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000IP =100C0218-100C0218: 9421FE38 stwu r1,-$1C8(r1)pROBE+> go

Enabling clock distribution to NLC bus ...

~>MAC Address? [] 12234567789a

Using typed MAC Address: 12234567789a

~>Internal IP Address? [159.23.14.18] 192.168.1.9

~>Subnet mask? [255.255.254.0] 255.255.255.0

~>Gateway? [159.23.14.254] 192.168.1.1

~>Host IP Address? [159.23.14.19] 192.168.1.10

Starting TFTP Agent ...

Two banks? (y/n) [y] y

~>Delivery directory? [c:\delivery\] \

~>Descriptor file? [NEHCB_SWU.txt]

Downloading "\NEHCB_SWU.txt" from Host 192.168.1.10

DESCRIPTOR DOWNLOADING....

Descriptor file OK.

NEHCB.bcx 0x10800000 0x490000SWRD_B.SM 0x12000000 0x10000PSYMED.bin 0x12040000 0x80000PRCC_FR2.bcx 0x120c0000 0x20000TARCB_F2.bin 0x120e0000 0x40000PHDC_FR2.bcx 0x12120000 0x20000BALCE_F2.bin 0x12140000 0x60000HC11.bcx 0x121a0000 0x10000PMLC_cde.bcx 0x121b0000 0x10000PMLC.bcx 0x121c0000 0x30000TACC1.bin 0x121f0000 0x10000TACCP2.bin 0x12200000 0x50000TACC3_F2.bin 0x12250000 0x30000HLTC_ke.bcx 0x12280000 0x30000H2FA100.bin 0x122b0000 0x30000HLTC.bcx 0x122e0000 0x30000BALCB.bcx 0x12310000 0x30000BALCG.bcx 0x12340000 0x40000BALCH.bcx 0x12380000 0x40000EOTCA.bcx 0x123c0000 0x30000EOTCB.bcx 0x123f0000 0x30000ALLC_FR2.bin 0x12420000 0x50000SALC_FR2.bcx 0x12470000 0x20000SLTC.bcx 0x12490000 0x50000SNSE.bsd 0x124e0000 0x30000SNDV.bsd 0x12510000 0x20000SNDE.bsd 0x12530000 0x20000GREC.bcx 0x12550000 0x40000IMLC.bcx 0x12590000 0x30000nehcbmap.bcx 0x125c0000 0x20000NEHBboot.bcx 0x125e0000 0x90000VISC_cde.bin 0x12670000 0x30000BALCC.bcx 0x126a0000 0x30000VISCB.bcx 0x126d0000 0x2e0000NEHCB.bcx 0x13f80000 0x490000SWRD_B.SM 0x15780000 0x10000PSYMED.bin 0x157c0000 0x80000PRCC_FR2.bcx 0x15840000 0x20000TARCB_F2.bin 0x15860000 0x40000PHDC_FR2.bcx 0x158a0000 0x20000BALCE_F2.bin 0x158c0000 0x60000HC11.bcx 0x15920000 0x10000PMLC_cde.bcx 0x15930000 0x10000PMLC.bcx 0x15940000 0x30000TACC1.bin 0x15970000 0x10000TACCP2.bin 0x15980000 0x50000

Se reemplaza por: “ \ “, que es el directorio de trabajo del TFTP server, definido anteriormente como: d:\temp

TACC3_F2.bin 0x159d0000 0x30000HLTC_ke.bcx 0x15a00000 0x30000H2FA100.bin 0x15a30000 0x30000HLTC.bcx 0x15a60000 0x30000BALCB.bcx 0x15a90000 0x30000BALCG.bcx 0x15ac0000 0x40000BALCH.bcx 0x15b00000 0x40000EOTCA.bcx 0x15b40000 0x30000EOTCB.bcx 0x15b70000 0x30000ALLC_FR2.bin 0x15ba0000 0x50000SALC_FR2.bcx 0x15bf0000 0x20000SLTC.bcx 0x15c10000 0x50000SNSE.bsd 0x15c60000 0x30000SNDV.bsd 0x15c90000 0x20000SNDE.bsd 0x15cb0000 0x20000GREC.bcx 0x15cd0000 0x40000IMLC.bcx 0x15d10000 0x30000nehcbmap.bcx 0x15d40000 0x20000NEHBboot.bcx 0x15d60000 0x90000VISC_cde.bin 0x15df0000 0x30000BALCC.bcx 0x15e20000 0x30000VISCB.bcx 0x15e50000 0x2e0000

DOWNLOADING.... NEHCB.bcx, flash add. 0x10800000, size 0x490000************************************1_____________________________________#####################################2_____________________________________##################################### OK.

DOWNLOADING.... SWRD_B.SM, flash add. 0x12000000, size 0x100001_#2_# OK.

DOWNLOADING.... PSYMED.bin, flash add. 0x12040000, size 0x80000***1____####2____#### OK.

DOWNLOADING.... PRCC_FR2.bcx, flash add. 0x120c0000, size 0x200001_#2_# OK.

DOWNLOADING.... TARCB_F2.bin, flash add. 0x120e0000, size 0x40000*1__##2__## OK.

DOWNLOADING.... PHDC_FR2.bcx, flash add. 0x12120000, size 0x200001_#2_# OK.

DOWNLOADING.... BALCE_F2.bin, flash add. 0x12140000, size 0x60000**1___###2___### OK.

DOWNLOADING.... HC11.bcx, flash add. 0x121a0000, size 0x100001_#2_# OK.

DOWNLOADING.... PMLC_cde.bcx, flash add. 0x121b0000, size 0x100001_#2_# OK.

DOWNLOADING.... PMLC.bcx, flash add. 0x121c0000, size 0x30000*1__##2__## OK.

DOWNLOADING.... TACC1.bin, flash add. 0x121f0000, size 0x100001_#2_# OK.

DOWNLOADING.... TACCP2.bin, flash add. 0x12200000, size 0x50000**1___###2___### OK.

DOWNLOADING.... TACC3_F2.bin, flash add. 0x12250000, size 0x30000*1__##2__## OK.

DOWNLOADING.... HLTC_ke.bcx, flash add. 0x12280000, size 0x30000*1__##2__## OK.

DOWNLOADING.... H2FA100.bin, flash add. 0x122b0000, size 0x30000*1__##2__## OK.

DOWNLOADING.... HLTC.bcx, flash add. 0x122e0000, size 0x30000*1__##2__## OK.

DOWNLOADING.... BALCB.bcx, flash add. 0x12310000, size 0x30000*1__##2__## OK.

DOWNLOADING.... BALCG.bcx, flash add. 0x12340000, size 0x40000*1__##2__## OK.

DOWNLOADING.... BALCH.bcx, flash add. 0x12380000, size 0x40000*1__##2__## OK.

DOWNLOADING.... EOTCA.bcx, flash add. 0x123c0000, size 0x30000*1__##2__## OK.

DOWNLOADING.... EOTCB.bcx, flash add. 0x123f0000, size 0x30000*1__##2__## OK.

DOWNLOADING.... ALLC_FR2.bin, flash add. 0x12420000, size 0x50000**1___###2___### OK.

DOWNLOADING.... SALC_FR2.bcx, flash add. 0x12470000, size 0x200001__##2__## OK.

DOWNLOADING.... SLTC.bcx, flash add. 0x12490000, size 0x50000**1___###2___### OK.

DOWNLOADING.... SNSE.bsd, flash add. 0x124e0000, size 0x30000*1__##2__## OK.

DOWNLOADING.... SNDV.bsd, flash add. 0x12510000, size 0x200001__##2__## OK.

DOWNLOADING.... SNDE.bsd, flash add. 0x12530000, size 0x200001__##2__## OK.

DOWNLOADING.... GREC.bcx, flash add. 0x12550000, size 0x40000*1___###2___### OK.DOWNLOADING.... IMLC.bcx, flash add. 0x12590000, size 0x30000*1__##2__## OK.

DOWNLOADING.... nehcbmap.bcx, flash add. 0x125c0000, size 0x200001_#2_# OK.

DOWNLOADING.... NEHBboot.bcx, flash add. 0x125e0000, size 0x90000****1_____#####2_____##### OK.

DOWNLOADING.... VISC_cde.bin, flash add. 0x12670000, size 0x30000*1__##2__## OK.

DOWNLOADING.... BALCC.bcx, flash add. 0x126a0000, size 0x30000*1__##2__## OK.

DOWNLOADING.... VISCB.bcx, flash add. 0x126d0000, size 0x2e0000**********************1________________________########################2________________________######################## OK.

... se repite el proceso de descarga para la segunda placa NEHC

DOWNLOADING.... NEHCB.bcx, flash add. 0x13f80000, size 0x490000************************************1_____________________________________#####################################2_____________________________________##################################### OK.

DOWNLOADING.... SWRD_B.SM, flash add. 0x15780000, size 0x100001_#2_# OK.

DOWNLOADING.... PSYMED.bin, flash add. 0x157c0000, size 0x80000***1____####2____#### OK.

DOWNLOADING.... PRCC_FR2.bcx, flash add. 0x15840000, size 0x200001_#2_# OK.

DOWNLOADING.... TARCB_F2.bin, flash add. 0x15860000, size 0x40000*1__##2__## OK.

DOWNLOADING.... PHDC_FR2.bcx, flash add. 0x158a0000, size 0x200001_#2_# OK.

DOWNLOADING.... BALCE_F2.bin, flash add. 0x158c0000, size 0x60000**1___###2___### OK.

DOWNLOADING.... HC11.bcx, flash add. 0x15920000, size 0x100001_#2_# OK.

DOWNLOADING.... PMLC_cde.bcx, flash add. 0x15930000, size 0x10000

1_#2_# OK.

DOWNLOADING.... PMLC.bcx, flash add. 0x15940000, size 0x30000*1__##2__## OK.

DOWNLOADING.... TACC1.bin, flash add. 0x15970000, size 0x100001_#2_# OK.

DOWNLOADING.... TACCP2.bin, flash add. 0x15980000, size 0x50000**1___###2___### OK.

DOWNLOADING.... TACC3_F2.bin, flash add. 0x159d0000, size 0x30000*1__##2__## OK.

DOWNLOADING.... HLTC_ke.bcx, flash add. 0x15a00000, size 0x30000*1__##2__## OK.

DOWNLOADING.... H2FA100.bin, flash add. 0x15a30000, size 0x30000*1__##2__## OK.

DOWNLOADING.... HLTC.bcx, flash add. 0x15a60000, size 0x30000*1__##2__## OK.

DOWNLOADING.... BALCB.bcx, flash add. 0x15a90000, size 0x30000*1__##2__## OK.

DOWNLOADING.... BALCG.bcx, flash add. 0x15ac0000, size 0x40000*1__##2__## OK.

DOWNLOADING.... BALCH.bcx, flash add. 0x15b00000, size 0x40000*1__##2__## OK.

DOWNLOADING.... EOTCA.bcx, flash add. 0x15b40000, size 0x30000*1__##2__## OK.

DOWNLOADING.... EOTCB.bcx, flash add. 0x15b70000, size 0x30000*1__##2__## OK.

DOWNLOADING.... ALLC_FR2.bin, flash add. 0x15ba0000, size 0x50000**1___###2___### OK.

DOWNLOADING.... SALC_FR2.bcx, flash add. 0x15bf0000, size 0x200001__##2__## OK.

DOWNLOADING.... SLTC.bcx, flash add. 0x15c10000, size 0x50000**1___###2___### OK.

DOWNLOADING.... SNSE.bsd, flash add. 0x15c60000, size 0x30000*1__##2__## OK.

DOWNLOADING.... SNDV.bsd, flash add. 0x15c90000, size 0x200001__##2__## OK.

DOWNLOADING.... SNDE.bsd, flash add. 0x15cb0000, size 0x200001__##2__## OK.

DOWNLOADING.... GREC.bcx, flash add. 0x15cd0000, size 0x40000*1___###2___### OK.

DOWNLOADING.... IMLC.bcx, flash add. 0x15d10000, size 0x30000*1__##2__## OK.

DOWNLOADING.... nehcbmap.bcx, flash add. 0x15d40000, size 0x200001_#2_# OK.

DOWNLOADING.... NEHBboot.bcx, flash add. 0x15d60000, size 0x90000****1_____#####2_____##### OK.

DOWNLOADING.... VISC_cde.bin, flash add. 0x15df0000, size 0x30000*1__##2__## OK.

DOWNLOADING.... BALCC.bcx, flash add. 0x15e20000, size 0x30000*1__##2__## OK.

DOWNLOADING.... VISCB.bcx, flash add. 0x15e50000, size 0x2e0000**********************1________________________########################2________________________######################## OK.

Continue TFTP Agent Application? (y/n) [y] n

Reseting ...

Initialating PROBE

Initialating PNA


Seed Version : NEHCSEED4.0.2Seed Date : 20 Jan 2007Seed Selection : Bank A Runnig Boot : Bank A. Boot Version : NEHCBOOT4.0.6Boot Date : 29 Jan 2007

Software Watchdog Reset : [Active]Very best copy with Watchdog Reset : [Active]Very best copy with Reset Buttom : [Active]Checksum Check : [Active]MPC885 Part number : 0x12.MPC885 Mask number : 0x0.Clock Frequency : 66 MHz.

Active Boot Bank & Active Ata Bank Joined

Loading FPGA's code from first application bank 0x12040000.

FPGA DOWNLOAD IS OK.

Reset Reason (RSR): 0xd0 => Software WatchDog Reset

Last Program Counter : [0x1012b7d0].

Loading Program from Application bank to RAM. Waiting...



SWD-PD-R3.0

V23.10.2

Download from bank 0. address 10800000. Size 48aab8

*****

Code is Compressed with CX Algorithm.Decompressing code from address 1e7a59c ... Application Code has not been executed. Checksum is skipped.




pROBE+> gs Kernel Event Break Running: 'ROOT' -#00020000 ------------------------------------------------------------------------------pSOS Initialized Event------------------------------------------------------------------------------

CR =00000000 XER=00000000 LR =DEADDEADCTR=00000000 MSR=00001032R0 =00000000 0230D0B0 01A012C0 00000000 00000000 00000000 00000000 00000000R8 =00000000 00000000 00000000 00000000 00000000 01A012A4 00000000 00000000R16=00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000R24=00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000IP =10081478-10081478: 9421FFF0 stwu r1,-$10(r1)pROBE+> go

NORMAL start (boot) ... OK


pROBE+> gs Kernel Event Break Running: 'ROOT' -#00020000 ------------------------------------------------------------------------------pSOS Initialized Event------------------------------------------------------------------------------CR =00000000 XER=00000000 LR =DEADDEADCTR=00000000 MSR=00001032R0 =00000000 028369A0 01A012C0 00000000 00000000 00000000 00000000 00000000R8 =00000000 00000000 00000000 00000000 00000000 01A012A4 00000000 00000000R16=00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000R24=00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000IP =00C217B4-00C217B4: 9421FFC0 stwu r1,-$40(r1)pROBE+> go

BSP_MMU [100db38] -> MMU Activated

BRD_ICACHE [100db30] -> Instruction Cache Activated

BRD_DCACHE [100db34] -> Data Cache Activated

Debug Mode Disabled

>To enable Debug Mode type 'pm.l 100db2c 1'.

Initializing, please wait...

Application uses the NEW IECB driver

0:00:00:02.58 TaskManagerPLc.cc:462 CreateAsociateStructs Tid:ROOT *** Warning: 9/status !!!! SM !!!! Logical Unit in FEPROM

IP Address = c0000005!!! DATA FEPROM HAS BEEN RESET !!!

NUMBER OF PERSISTENT DATA EXPECTED : 8

PERSISTENT DATA IN BANK 1 : 8.1.0.USERLABEL.ALCATEL.2000.0.1.0.0.0.0.0.0.0.0



!!! FIRST INSTALLATION !!!

!!! reading MasterSlave ToPeer:: I'm MASTER, Peer is SLAVE !!!

!!! restartReasonEH = UnknownPL !!!

0:00:00:15.63 CoreMain.cc:1392 !!! restartOnGoing = ColdRestartPL !!!


==== LIDR ===> LINUS_0 STATUS TYPE -> [03]STATUS INST -> 00 STATE -> LD_ACTIVE!!! change in MasterSlave ToPeer:: I MUST BE MASTER !!!

==== LIDR ===> LINUS_0 STATUS TYPE -> [03]STATUS INST -> 01 STATE -> LD_STAND_BY

IP Address = c0000005NUMBER OF PERSISTENT DATA EXPECTED : 8



PERSISTENT DATA IN BANK 1 : 8.1.0.USERLABEL.ALCATEL.2000.0.1.0.0.0.0.0.0.0.0 swpack1 SWD-PD-R3.0 version1 V23.10.2 nswu1 33 swpack2 SWD-PD-R3.0 version2 V23.10.2 nswu2 33

equal = TRUE2 Swrelease installed NUMBER OF PERSISTENT DATA EXPECTED : 8


swId 1 ,status 0

SOFTWARE version V23.10.2

ACT- Sent WakeupStbyBoardSMc, StbRestartType : 0

copyActSpareSMc returned 0 bootItfSMc.cc:

boot version in ATA: V4.0.7 boot version in bank A: V4.0.6 boot version in bank B: V4.0.6

Decompressing Nehc Boot

uncompressbootBlocksSMc: Uncompress from address 0x15d60052uncompressbootBlocksSMc: New address to Uncompress 0x15d84444uncompressbootBlocksSMc: Decompressed bytes 0xde2b0 = 910000

bootItfSMc.cc: same SEED version: V4.0.2

uncompressbootBlocksSMc: Uncompress from address 0x15d84444uncompressbootBlocksSMc: New address to Uncompress 0x15dd8ecbuncompressbootBlocksSMc: Decompressed bytes 0xde2b0 = 910000uncompressbootBlocksSMc: Uncompress from address 0x15dd8ecbuncompressbootBlocksSMc: New address to Uncompress 0x0uncompressbootBlocksSMc: Decompressed bytes 0x63aa0 = 408224

bootItfSMc.cc: BOOT BANK B UPDATED TO ATA VERSION !!!

bootItfSMc.cc: BOOT BANK A DUPLICATED.

Calling to Cold Restart :DownloadCoordinatorSMc.cc 596 Boot change

ErrHandlerPLc.cc#439 *** Software fault *** SS: A SU: p FC: 0x0254 FD: 0x0000 RC: 0x0080

Initialating PROBE

Initialating PNA


Seed Version : NEHCSEED4.0.2Seed Date : 20 Jan 2007Seed Selection : Bank A Runnig Boot : Bank A. Boot Version : NEHCBOOT4.0.7Boot Date : 20 Jun 2007

Software Watchdog Reset : [Active]Very best copy with Watchdog Reset : [Active]Very best copy with Reset Buttom : [Active]Checksum Check : [Active]MPC885 Part number : 0x12.

MPC885 Mask number : 0x0.Clock Frequency : 66 MHz.Active Boot Bank & Active Ata Bank Joined

Loading FPGA's code from first application bank 0x12040000.

FPGA DOWNLOAD IS OK.Reset Reason (RSR): 0xd0 => Software WatchDog ResetLast Program Counter : [0xc64218].

Loading Program from Application bank to RAM. Waiting...



SWD-PD-R3.0

V23.10.2

Download from bank 0. address 10800000. Size 48aab8

*****

Code is Compressed with CX Algorithm.Decompressing code from address 1e7a69c ... Application Code has not been executed. Checksum is skipped.




pROBE+> gs Kernel Event Break Running: 'ROOT' -#00020000 ------------------------------------------------------------------------------pSOS Initialized Event------------------------------------------------------------------------------CR =00000000 XER=00000000 LR =DEADDEADCTR=00000000 MSR=00001032R0 =00000000 0230D1B0 01A012C0 00000000 00000000 00000000 00000000 00000000R8 =00000000 00000000 00000000 00000000 00000000 01A012A4 00000000 00000000R16=00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000R24=00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000IP =10081478-10081478: 9421FFF0 stwu r1,-$10(r1)pROBE+> go



pROBE+> gs Kernel Event Break Running: 'ROOT' -#00020000 ------------------------------------------------------------------------------pSOS Initialized Event------------------------------------------------------------------------------CR =00000000 XER=00000000 LR =DEADDEADCTR=00000000 MSR=00001032R0 =00000000 028369A0 01A012C0 00000000 00000000 00000000 00000000 00000000R8 =00000000 00000000 00000000 00000000 00000000 01A012A4 00000000 00000000R16=00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000R24=00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000IP =00C217B4-00C217B4: 9421FFC0 stwu r1,-$40(r1)

pROBE+> go

BSP_MMU [100db38] -> MMU Activated

BRD_ICACHE [100db30] -> Instruction Cache Activated

BRD_DCACHE [100db34] -> Data Cache Activated

Debug Mode Disabled




0:00:00:02.59 TaskManagerPLc.cc:462 CreateAsociateStructs Tid:ROOT *** Warning: 9/status !!!! SM !!!! Logical Unit in FEPROM

IP Address = c0000005!!! DATA FEPROM HAS BEEN RESET !!!





!!! FIRST INSTALLATION !!!


!!! restartReasonEH = UnknownPL !!!




==== LIDR ===> LINUS_0 STATUS TYPE -> [03]STATUS INST -> 01 STATE -> LD_STAND_BY IP Address = c0000005NUMBER OF PERSISTENT DATA EXPECTED : 8




swpack1 SWD-PD-R3.0 version1 V23.10.2 nswu1 33 swpack2 SWD-PD-R3.0 version2 V23.10.2 nswu2 33

equal = TRUE

2 Swrelease installed NUMBER OF PERSISTENT DATA EXPECTED : 8


swId 1 ,status 0





ResourcesCCEL::start, subrack is 2 !ResourcesCCEL::start, Not Initital !ResourcecCCEL::start,Prepare create Auxiliary !

SwuActiva : 3EC 41873 CBAA03

[ROOT] Compare The ATA and Bckplane installation data[ROOT] Found different parameters[ROOT] ata.RackType: 3[ROOT] bck.RackType: 11[ROOT] ata.SubrackCap: 2[ROOT] bck.SubrackCap: 12[ROOT] ata.MacType: 2[ROOT] bck.MacType: 13[ROOT] ata.AccNode: 0[ROOT] bck.AccNode: 0

0:00:00:34.27 IntfAmiIdSMc.cc:1349 IntfAmiIdSMc Tid:ROOT *** Error: -1

[ROOT] Write MBTP installation data to ATA card and reset the NE


WRITE_PER PERSISTENT DATA IN BANK 1.0.USERLABEL.ALCATEL.2000.0.1.0.0.0.0.0.0.0.0

0:00:00:34.32 FepromSMc.cc:1298 fepWriteIDDSCSMc add 15780000 size 27217


IP Address = c0000005Enabling the 16x2M cross-connection interface in startMCEL

BchpRectifierEQc::BchRectifierEQc, Construct !!!ConverterCCEL::start, Entering !BchpRectifierEQc::BchRectifierEQc, Construct !!!ConverterCCEL::start, Entering !BatteryEQc::subscribeToAlarmMngt, Entering 0 ! AccessNEEQc::startChildren , AlarmMngt is 0 !LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[0] .linkId=[0] .tsl[0].chType=[COMM_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[1] .linkId=[1] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[2] .linkId=[2] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[3] .linkId=[3] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[4] .linkId=[4] .tsl[0].chType=[COMM_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[5] .linkId=[5] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[6] .linkId=[6] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[7] .linkId=[7] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[8] .linkId=[8] .tsl[0].chType=[COMM_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[9] .linkId=[9] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[10] .linkId=[10] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[11] .linkId=[11] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[12] .linkId=[12] .tsl[0].chType=[COMM_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[13] .linkId=[13] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[14] .linkId=[14] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[15] .linkId=[15] .tsl[0].chType=[BEARER_CH]

country set to Spain

**** ASSIGN TARC CARD with pnt = 0******. MLS_hb_16 Applied.

CREATO TAP CON PUNTATORE UGUALE A 262ddb0

create TestActionPerformer

*** RICOPIATO PUNTATORE TAP NELL' ATTRIBUTO pTestActionPerformer ****

!!! Idle pattern in Medusa channels without Cross-Connection!!!


!!! setting SoftwareEnableRDFD = OFF !!!

!!! setting GlobalAlarm = OFF !!!


WRITE_PER PERSISTENT DATA IN BANK 1.0.USERLABEL.ALCATEL.2000.0.1.0.0.0.0.0.0.0.0



CHDR: Channel 0 TSTATE = 0x30000000CHDR: Channel 1 TSTATE = 0x30000000!!! OBJECT INIT END !!!

--- VAV5Adaptor Task Running ---

0:00:00:43.66 CoreMain.cc:1600 ** Management (CT/OS) starting **

Calling to ChangeIDColdRestartPL :IntfAmiIdSMc.cc 285 change IDdata cold

ErrHandlerPLc.cc#587 *** Software fault *** SS: A SU: p FC: 0x011D FD: 0x0000 RC: 0x0080

RootTask suspended

Starting Telnet Server ... **** We are the AGENT ****

tpstartMAC Address = 00:80:9f:2d:88:e7

Proxy Arp App. Initilized Circuit start OK!Telegenics TMN Management Illustrative Agent based on Toolkit Version 2.1(c) Copyright Telegenics 1989 - 1995

***** tkmoi_initialiseMIB

***** tkmoi_initialiseMIB-end

***** activate

***** activate end

Initialating PROBE

Initialating PNA


Seed Version : NEHCSEED4.0.2Seed Date : 20 Jan 2007Seed Selection : Bank A Runnig Boot : Bank A. Boot Version : NEHCBOOT4.0.7Boot Date : 20 Jun 2007

Software Watchdog Reset : [Active]

Very best copy with Watchdog Reset : [Active]Very best copy with Reset Buttom : [Active]Checksum Check : [Active]MPC885 Part number : 0x12.MPC885 Mask number : 0x0.Clock Frequency : 66 MHz.

Active Boot Bank & Active Ata Bank JoinedLoading FPGA's code from first application bank 0x12040000.FPGA DOWNLOAD IS OK.Reset Reason (RSR): 0xd0 => Software WatchDog ResetLast Program Counter : [0xc64218].

Loading Program from Application bank to RAM. Waiting...Active Boot Bank & Active Ata Bank Joined


SWD-PD-R3.0

V23.10.2

Download from bank 0. address 10800000. Size 48aab8*****Code is Compressed with CX Algorithm.Decompressing code from address 1e7a69c ... Application Code has not been executed. Checksum is skipped.




pROBE+> gs Kernel Event Break Running: 'ROOT' -#00020000 ------------------------------------------------------------------------------pSOS Initialized Event------------------------------------------------------------------------------CR =00000000 XER=00000000 LR =DEADDEADCTR=00000000 MSR=00001032R0 =00000000 0230D1B0 01A012C0 00000000 00000000 00000000 00000000 00000000R8 =00000000 00000000 00000000 00000000 00000000 01A012A4 00000000 00000000R16=00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000R24=00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000IP =10081478-10081478: 9421FFF0 stwu r1,-$10(r1)pROBE+> go



pROBE+> gs Kernel Event Break Running: 'ROOT' -#00020000 ------------------------------------------------------------------------------pSOS Initialized Event------------------------------------------------------------------------------CR =00000000 XER=00000000 LR =DEADDEADCTR=00000000 MSR=00001032R0 =00000000 028369A0 01A012C0 00000000 00000000 00000000 00000000 00000000R8 =00000000 00000000 00000000 00000000 00000000 01A012A4 00000000 00000000R16=00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000R24=00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000IP =00C217B4-00C217B4: 9421FFC0 stwu r1,-$40(r1)pROBE+> go

BSP_MMU [100db38] -> MMU ActivatedBRD_ICACHE [100db30] -> Instruction Cache ActivatedBRD_DCACHE [100db34] -> Data Cache Activated

Debug Mode Disabled




0:00:00:02.56 TaskManagerPLc.cc:462 CreateAsociateStructs Tid:ROOT *** Warning: 9/status

!!!! SM !!!! Logical Unit in FEPROM

IP Address = c0000005NUMBER OF PERSISTENT DATA EXPECTED : 8





!!! restartReasonEH = ChangeIDColdRestartPL !!!




==== LIDR ===> LINUS_0 STATUS TYPE -> [03]STATUS INST -> 01 STATE -> LD_STAND_BY IP Address = c0000005NUMBER OF PERSISTENT DATA EXPECTED : 8



PERSISTENT DATA IN BANK 1 : 8.1.0.USERLABEL.ALCATEL.2000.0.1.0.0.0.0.0.0.0.0 swpack1 SWD-PD-R3.0 version1 V23.10.2 nswu1 33 swpack2 SWD-PD-R3.0 version2 V23.10.2 nswu2 33

equal = TRUE2 Swrelease installed NUMBER OF PERSISTENT DATA EXPECTED : 8


swId 1 ,status 0


Reinit State : 6

Start up reason SWReUnknownPL o IDChangeInProcessPL o SWReFinishedPL




ResourcesCCEL::start, subrack is c !

ResourcesCCEL::start, Not Initital !

ResourceCCEL::start, Prepare create AlarmMngt!

ResourceCCEL::start, Prepare reinit AlarmMngt!

LIOC works normally

. . DIAG: Load LIOC Alarms Matrix............. 0 !!!!!

. . DIAG: Matrix loaded ............. 0 !!!!!

LIOC works normally

SwuActiva : 3EC 41873 CBAA03

Enabling the 16x2M cross-connection interface in startMCEL

AccessNEEQc::startChildren , AlarmMngt is 6cf402c !AccessNEEQc::startChildren, subscribe to the RepStateChange and RepExtDeviceFailure !LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[0] .linkId=[0] .tsl[0].chType=[COMM_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[1] .linkId=[1] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[2] .linkId=[2] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[3] .linkId=[3] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[4] .linkId=[4] .tsl[0].chType=[COMM_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[5] .linkId=[5] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[6] .linkId=[6] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[7] .linkId=[7] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[8] .linkId=[8] .tsl[0].chType=[COMM_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[9] .linkId=[9] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[10] .linkId=[10] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[11] .linkId=[11] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[12] .linkId=[12] .tsl[0].chType=[COMM_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[13] .linkId=[13] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[14] .linkId=[14] .tsl[0].chType=[BEARER_CH]LinkResourceMgrV5SL::LinkResourceMgrV5SL - tSBData_[15] .linkId=[15] .tsl[0].chType=[BEARER_CH]

country set to Spain

**** ASSIGN TARC CARD with pnt = 0******. MLS_hb_16 Applied.

CREATO TAP CON PUNTATORE UGUALE A 26257b0

create TestActionPerformer

*** RICOPIATO PUNTATORE TAP NELL' ATTRIBUTO pTestActionPerformer ****

!!! Idle pattern in Medusa channels without Cross-Connection!!!


!!! setting SoftwareEnableRDFD = OFF !!!

!!! setting GlobalAlarm = OFF !!!

!!! OBJECT INIT END !!!

0:00:00:27.92 CoreMain.cc:1600 ** Management (CT/OS) starting **

--- VAV5Adaptor Task Running ---

LIOC works normally

RootTask suspended

Starting Telnet Server ...

**** We are the AGENT ****

tpstartMAC Address = 00:80:9f:2d:88:e7

Proxy Arp App. Initilized Circuit start OK!Telegenics TMN Management Illustrative Agent based on Toolkit Version 2.1(c) Copyright Telegenics 1989 - 1995

LIOC works normally

***** tkmoi_initialiseMIB

***** tkmoi_initialiseMIB-end

***** activate

***** activate end

LIOC works normally

DCCP STf 0-15 ms=44630

Procedure to Download Software via Tftp in Nehc

Documents

Transcript of Procedure to Download Software via Tftp in Nehc