Pressure Drop Basics & Valve Sizing - Watts · pressure differential Available Pressure at Valve...
Transcript of Pressure Drop Basics & Valve Sizing - Watts · pressure differential Available Pressure at Valve...
Pressure Drop Basics & Valve Sizing
What is Pressure Drop?What is Pressure Drop?
The difference in pressure between two points in a system, caused by resistance to flow.
What Pressure Drop is Not?What Pressure Drop is Not?
Pressure drop is pressure loss across the valve created by system demand - NOT by the valve alone.
What is Pressure Drop?What is Pressure Drop?
Pressure Drop = P = Pressure Differential = PSIG
(from Greek Delta) is a change in something; in this case a change or drop in pressure at the valve as a result of system demand.
What is Pressure Drop?
To determine Delta P across a valve, subtract the outlet pressure (P2) from the inlet pressure (P1).
The equation is (P1) – (P2) = P
431
Ex: Pressure Drop
7.5 gpm
100 psi
95 psi
100psi - 95psi = Δ 5psi
Model 431 Valve: Flows 7.5 GPM @ 5psi differential (see table, next page)
Pressure Drop Table
Available Pressure at ValveModel # Min Flow Min Flow to 5 10 20 30 45 60 100
* Rate ASSE 1017 Flow Rate in GPM431 0.5 4 7.5 11 16 20 25 29 38.5432 0.5 7 15 20 30 36 45 52 67433 0.5 10 24 34 51 64 80 93 123434 0.5 15 40 55 82 101 125 146 190
1432 0.5 1.5 14 18 27 33 40 46 601434 0.5 5 32 45 66 80 100 117 152
* Minimum flow when installed at or near hot water source with recirculating tempered water & continuously recirculating pump
Why is Pressure Drop Important?
Pressure drop is a critical element in valve sizing and valve application. Pressure drop must be known by the engineer designing the system to ensure proper valve selection.
What Factors Determine Pressure Drop?
Critical factors are orifice size and internal flow path.
Ex: Full port-full open 1” ball valve with a Cv of 40 vs. a full open 1” diaphragm valve with a Cv of 15.
What is the Relationship between Flow Rate and Pressure Drop?
Pressure drop and flow rate are dependant on one another. The higher the flow rate through a restriction, the greater the pressure drop. Conversely, the lower the flow rate, the lower the pressure drop.
What is Cv?
The definition of Cv factor is the number of G.P.M. that will pass through a valve with a pressure drop of one (1) psi.
A unit of measure for comparing valve flows.
How do P, Cv and GPM work together to size a valve?
Two of these elements are necessary to size a valve:
Where G = Specific Gravity of the Fluid
System Design
• Estimating Water Demand• Pipe Sizing• System Operating Pressure• Master Mixing Valves• Design Temperature• Maintaining Temperature
Estimating Demand: Methods
Full Flow50 units or lessUnusual demand
Hunter’s MethodMore than 50 unitsTypical demand
Full Flow Sizing
• Used when there are less than 50 fixture units• Add up requirement for all fixtures• Multiply by H/C factor• Determine Actual Flow Required (in gpm)
H/C Factor = Shower temp - cold tempMixing Valve temp - cold temp
Ex: Full Flow Sizing
• Outlet 105°F - CW 60 °F = 45 °F • HW 125 °F – CW 60 °F = 65
45 / 65 = 69%• If the Fixture Requirement for 10 showers is
25 gpm, the valve should be sized at 69% of this requirement:
69% x 25 = 17 gpm
Locker Room with 10 showers
Full Flow Sizing
If the pressure available at the valve is 45 PSI, we can select a valve that will Flow 17 GPM @ 25 PSI. Our selection will be a 431.
Available Pressure at ValveModel # Min Flow Min Flow to 5 10 20 30 45 60 100
Rate ASSE 1017 Flow Rate in GPM431 0.5 4 7.5 11 16 20 25 29 38.5432 0.5 7 15 20 30 36 45 52 67433 0.5 10 24 34 51 64 80 93 123434 0.5 15 40 55 82 101 125 146 190
1432 0.5 1.5 14 18 27 33 40 46 601434 0.5 5 32 45 66 80 100 117 152
Hunter’s Curve
Devised by Dr. Roy B. Hunter in the 1950s
Report titled BMS65, Estimating Loads in Plumbing Systems
Concept of fixture unit weights with probability curves or “Hunter’s Curves”
Modified since for today’s requirements
Hunters Curve
Method for determining valve size based on hot water demand in plumbing systems.
The probability function is used to determine the number of plumbing fixtures that would reasonably be expected to be in simultaneous operation.
Hunters Curve
The demand for any given fixture in the system is the combination of:
1. Cycle time2. Demand flow rate 3. Frequency of Use
Hunters Curve
The Hunter method is applicable to the design of all plumbing systems, it is especially useful for systems that expect a high public demand -- such as healthcare facilities, sports stadiums, schools, hotels, etc.
Fixtures:Apart. House
Club or Gym Hospital
Hotel / Dormitory
Industrial Plant
School Office Bld
Basins, Private Lavatory 0.75 0.75 0.75 0.75 0.75 0.75Basins, Public Lavatory - 1 1 1 1 1Bathtubs / Showers 1.5 1.5 1.5 1.5 3.5 1.5Dishwasher 1.5 - Five (5) Fixture Units per 250 Seating CapacityTherapeutic Bath - - 5 - - -Kitchen Sink 0.75 1.5 3 1.5 3 0.75Pantry Sink - 2.5 2.5 2.5 - 2.5Service Sink 1.5 2.5 2.5 2.5 2.5 2.5Circular Wash Fountain - 2.5 2.5 - 4 2.5Semicircular Wash Fount - 1.5 1.5 - 3 1.5
Hunter’s Fixture Units by Facility Type
In applications where the principal use is showers, as a gym, use conversion factor of 1.00 to obtain design water flow rate in gpm.
Ex: Hunters Method Sizing (Hotel w/100 Rooms)
100 Showers: 100 x 1.5 = 150 Fixture Units
100 Private Lavs 100 x 0.75 = 75 Fixture Units
10 Public Lavs: 10 x 1 = 10 Fixture Units
2 Kitchen Sinks 2 x 1.5 = 3 Fixture Units
5 Service Sink 5 x 2.5 = 10 Fixture Units
TOTAL : 248 FIXTURE UNITS
Hunter’s Method Sizing
Hunter’s Curve
Actual Flow Requirement at 248 Fixture Units = 50 gpm
Hunter’s Method Sizing
Most manufacturers have sizing programs available that make demand estimation with Hunter’s Curve a snap!
Estimating Available Pressure
• Available Pressure– Water Pressure At Valve– Minus 20 psi For the Last Fixture– Minus 5 psi for each floor the highest
fixture is above the valve– Minus 2 psi for each 100’ of horizontal
piping
Pressure At the Inlet of the Valve: +60 psi
Min. Design Pressure @ Fixture: - 20 psi
2 Floors above Valve location: 5 psi x 2 - 10 psi
300’ of Horiz. Friction Loss: 300 x 0.02: - 6 psi
Total Available Pressure at the Valve: +24 psi
Ex: Hunter’s Method Sizing
We now need a valve that will flow 50 gpm @ 24 psig
Select a Valve
Select a valve with enough flow to meet your demand at the available
pressure differential
Available Pressure at ValveModel # Min Flow Min Flow to 5 10 20 30 45 60 100
Rate ASSE 1017 Flow Rate in GPM431 0.5 4 7.5 11 16 20 25 29 38.5432 0.5 7 15 20 30 36 45 52 67433 0.5 10 24 34 51 64 80 93 123434 0.5 15 40 55 82 101 125 146 190
1432 0.5 1.5 14 18 27 33 40 46 601434 0.5 5 32 45 66 80 100 117 152
24
Our choice will be the 433 valve
Sizing ProgramsSimple to use valve sizing programs will help you select the proper valve for any application by answering simple questions.
Sizing Programs- Notes and Summary of Section.
- Save Projects
- Email/Share
Thank you.