PRESS RELEASE 07/15

Torque And More GmbH • Münchener Str. 33, D-82319 Starnberg • Tel: +49 8151 368 981 30 • [email protected] www.tam-sensors.com Measure Torque instantly: Place a cigar-sized probe from one side onto the Test-Object (like: gearbox shaft), push the initialisation button and Torque measurements can start right away. High signal resolution equivalent to 14 bits, high system internal signal bandwidth equivalent to 10,000 samples per second, and high measurement linearity of 0.2% of FS (Full Scale). The Active-3 Torque Sensor is ideal for industrial, motor- sport, and power-tool applications. Insensitive to air gap changes • No shaft processing required • No damage due to over-torque • Does not age • Air gap can be up to 3 mm • Any Ferro-magnetic material • Insensitive to oil, dirt, paint, etc. • Analogue Signal (5 Volt) • Wide temperature range • Single voltage supply • Windows-PC USB Interface Sensing Module Design: PRESS RELEASE 07/15 CONTACT US! Torque And More GmbH Münchener Str. 33 82319 Starnberg, Germany Tel: +49 (0) 8151 368 981 30 Fax: +49 (0) 8151 368 982 99 Sales: [email protected] Web: www.tam-sensors.com Distance Compensated Advanced Active-3 Torque Sensors Non-Contact, Plug-and-Play, Harsh Operating Conditions TAM offers “standard” and custom speciﬁc Sensing Module designs to meet a wide range of application speciﬁc requirements. The Sensing Mod- ule is connected to the Sensor Electronics by a cable that can be up to 2.5 meters long. Inside the Sensing Module is the round shaped Sensing Ele- ment with a minimum diameter of 20 mm. The face of the Sensing Mod- ule is concave to sit closer to the surface of the Test-Object (like gearbox shaft). The Sensing Module is not touching the Test-Object and can be placed up-to 3 mm away from it (maximum air-gap is 3 mm). The “zero” to +5 Volt analogue signal output of the A3 Sensor System provides very linear and low hysteresis Torque measurements. Shaft material: DIN 1.2767 / 45NiCrMo16 Shaft diameter: Ø 25 mm The Advanced A3 Torque Sensor is insensitive to changes in the air gap during Torque Measurements (relative air gap compensation range is 0.2 to 0.5 mm). Active-3 Torque Sensor Kit: Sensing Module, Sensor Electronics, Power Supply, Software, Cable and manual Visit our website media section www.tam-sensors.com/media

Upload
others
Category

Documents
view
1
download
0

Embed Size (px):

Transcript of PRESS RELEASE 07/15

Torque And More GmbH • Münchener Str. 33, D-82319 Starnberg • Tel: +49 8151 368 981 30 • [email protected]

www.tam-sensors.com

Measure Torque instantly: Place a cigar-sized probe from one side onto the Test-Object (like: gearbox shaft), push the initialisation button and Torque measurements can start right away.

High signal resolution equivalent to 14 bits, high system internal signal bandwidth equivalent to 10,000 samples per second, and high measurement linearity of 0.2% of

FS (Full Scale). The Active-3 Torque Sensor is ideal for industrial, motor-sport, and power-tool applications.

• Insensitive to air gap changes

• No shaft processing required• No damage due to over-torque• Does not age• Air gap can be up to 3 mm • Any Ferro-magnetic material• Insensitive to oil, dirt,

paint, etc.• Analogue Signal (5 Volt)• Wide temperature range• Single voltage supply• Windows-PC USB Interface

Sensing Module Design:

PRESS RELEASE 07/15

Torque And More GmbHMünchener Str. 33 82319 Starnberg, Germany Tel: +49 (0) 8151 368 981 30 Fax: +49 (0) 8151 368 982 99Sales: [email protected] Web: www.tam-sensors.com

Distance Compensated

Advanced Active-3 Torque SensorsNon-Contact, Plug-and-Play, Harsh Operating Conditions

TAM offers “standard” and custom specific SensingModule designs tomeetawiderangeofapplicationspecificrequirements.TheSensingMod-ule is connected to the Sensor Electronics by a cable that can be up to 2.5 meters long. Inside the Sensing Module is the round shaped Sensing Ele-ment with a minimum diameter of 20 mm. The face of the Sensing Mod-ule is concave to sit closer to the surface of the Test-Object (like gearbox shaft). The Sensing Module is not touching the Test-Object and can be placed up-to 3 mm away from it (maximum air-gap is 3 mm).

The “zero” to +5 Volt analogue signal output of the A3 Sensor System provides very linear and low hysteresis Torque measurements.

Shaft material: DIN 1.2767 / 45NiCrMo16Shaft diameter: Ø 25 mm

The Advanced A3 Torque Sensor is insensitive to changes in the air gap during Torque Measurements (relative air gap compensation range is 0.2 to 0.5 mm).

Active-3 Torque Sensor Kit: Sensing Module, Sensor Electronics, Power Supply, Software, Cable and manual

Visit our website media sectionwww.tam-sensors.com/media