Premium Tile & Stone Installation Products · hydrostatic/negative water pressure can occur. Ÿ...
6
Product Description: CREST MEMBRANA 3010® Urethane ultimate technology, waterproofing, crack prevention and sound isolation membrane, ready to use, one part, trowel applied over properly prepared concrete, exterior grade plywood (interior/dry use only); cementitious backer board and existing, well-bonded vinyl/VCT or ceramic tile; prior to the installation of ceramic or stone tile. Product Benefits: Ÿ High Tech Flexibility allows for movement. Ÿ Applied over cracks up to 1/8”. Ÿ Excellent Bond. Ÿ Ready to use. Ÿ Fast and easy application. Ÿ Low odor. Ÿ Antimicrobial protection. Ÿ Residential and commercial use. Ÿ Use for horizontal or vertical installations. Ÿ Smooth and creamy consistency. Ÿ Sound isolation. Suitable Substrates: Ÿ Cement plasters. Ÿ Cement backer board. Ÿ Fully cured concrete. Ÿ Exterior grade plywood (exterior / dry use only). Ÿ Properly prepared existing ceramic tiles or stone tiles. Ÿ Vinyl/VCT. Composition CREST MEMBRANA 3010® is a pre-mix membrane, ready to use, formulated with urethane binder and chemicals additives. Limitations of the Product Ÿ Install only at temperatures between 50°F and 100°F (10°C and 38°C). Ÿ Total thickness of the material should not exceed 3/32”or 90 mils. Ÿ Do not use it as a wear surface. Ÿ It must be covered with approved flooring materials using approved application methods. Ÿ CREST MEMBRANA 3010® is a “positive side” waterproofing membrane only. Do not use where hydrostatic/negative water pressure can occur. Ÿ CREST MEMBRANA 3010® is not intended to reduce sub-floor moisture or moisture vapor transmission. Ÿ CREST MEMBRANA 3010® is not designed for use in joints/cracks with dynamic movement (i.e. expansion, isolation, or construction joints). Ÿ As a waterproofing/anti-fracture/sound reduction membrane CREST MEMBRANA 3010® is designed for movement of 1/8”, or less. Ÿ CREST MEMBRANA 3010® if it is exposed to excessive moisture while curing, membrane may exhibit bubbles or pinholes. Ÿ When used as a waterproofing membrane, fill any pinholes or pitting with a second coat of CREST MEMBRANA 3010®. If pinholes are excessive, cut-out affected area and replace with fresh material. www.crest.com.mx [email protected] Premium Tile & Stone Installation Products URETHANE BASED Waterproofing, Crack Prevention & Sound Isolation Membrane
Transcript of Premium Tile & Stone Installation Products · hydrostatic/negative water pressure can occur. Ÿ...
Product Description: CREST MEMBRANA 3010® Urethane ultimate technology, waterproofing, crack prevention and sound isolation membrane, ready to use, one part, trowel applied over properly prepared concrete, exterior grade plywood (interior/dry use only); cementitious backer board and existing, well-bonded vinyl/VCT or ceramic tile; prior to the installation of ceramic or stone tile.
Product Benefits:Ÿ High Tech Flexibility allows for movement.Ÿ Applied over cracks up to 1/8”.Ÿ Excellent Bond.Ÿ Ready to use.Ÿ Fast and easy application.Ÿ Low odor.Ÿ Antimicrobial protection.Ÿ Residential and commercial use.Ÿ Use for horizontal or vertical installations.Ÿ Smooth and creamy consistency.Ÿ Sound isolation.
Suitable Substrates:Ÿ Cement plasters.Ÿ Cement backer board.Ÿ Fully cured concrete.Ÿ Exterior grade plywood (exterior / dry use only).Ÿ Properly prepared existing ceramic tiles or stone tiles.Ÿ Vinyl/VCT.
CompositionCREST MEMBRANA 3010® is a pre-mix membrane, ready to use, formulated with urethane binder and chemicals additives.
Limitations of the ProductŸ Install only at temperatures between 50°F and 100°F
(10°C and 38°C).
Ÿ Total thickness of the material should not exceed 3/32”or 90 mils.
Ÿ Do not use it as a wear surface.
Ÿ It must be covered with approved flooring materials using approved application methods.
Ÿ CREST MEMBRANA 3010® is a “positive side” waterproofing membrane only. Do not use where hydrostatic/negative water pressure can occur.
Ÿ CREST MEMBRANA 3010® is not intended to reduce sub-floor moisture or moisture vapor transmission.
Ÿ CREST MEMBRANA 3010® is not designed for use in joints/cracks with dynamic movement (i.e. expansion, isolation, or construction joints).
Ÿ As a waterproofing/anti-fracture/sound reduction membrane CREST MEMBRANA 3010® is designed for movement of 1/8”, or less.
Ÿ CREST MEMBRANA 3010® if it is exposed to excessive moisture while curing, membrane may exhibit bubbles or pinholes.
Ÿ When used as a waterproofing membrane, fill any pinholes or pitting with a second coat of CREST MEMBRANA 3010®. If pinholes are excessive, cut-out affected area and replace with fresh material.
www.crest.com.mx [email protected]
Premium Tile & Stone Installation Products
URETHANE BASED Waterproofing, Crack Prevention
& Sound Isolation Membrane
Surface PreparationBefore preparing the mixture of CREST MEMBRANA 3010® it is necessary to clean the surface, which must be structurally sound, dimensionally stable, flat and clean, free from oil, paint, sealers, wax, dirt or any other type of impurity that might prevent proper adhesion.
All cracks (1/8” or less), corners, drains, pipes should be treated by applying CREST MEMBRANA 3010® with the flat side of the trowel to achieve a flat, reinforced, uniformly thick membrane (30-mil. minimum). A minimum 6” wide coat should be applied to both sides of the joint, crack, or intersection.
Cracks greater than 1/8” should be treated, by inserting a backer rod, bond breaker tape or fill the crack/joint with CREST FLEXIGROUT®. Let it cure for 2 hr. approx. consult respective Technical Data Sheet for more information or consult www.crest.com.mx for technical assistance.
After the cracks are filled, follow the Product Application Instructions below.
Mixing ProceduresUse the appropriate safety equipment, such chemical-resistant gloves when handling product.
CREST MEMBRANA 3010® is ready to use, simply open the product, mix and apply.
Directions
Premium Tile & Stone Installation Products
Product ApplicationFollow applicable ANSI, TCNA and NTCA installation standards. Read to understand TDS completely before beginning installation.
Waterproofing, noise reduction, and crack isolation: Apply CREST MEMBRANA 3010® using the notched side of a 3/16” x 5/32” V-Notch Trowel, immediately smooth material with flat side of trowel to achieve a flat, uniformly thick membrane with a minimum wet thickness of 30-mil (thickness of a credit card).
Anti-fracture/crack Isolation membrane: Apply CREST MEMBRANA 3010® using the notched side of a 3/16” x 5/32” V-Notch Trowel. Immediately smooth the material with flat side of trowel to achieve a flat, uniformly thick membrane with a minimum wet thickness of 30-mil (thickness of a credit card). The membrane should be applied to both sides of the crack/joint a minimum of the width of the tile being installed (i.e. a 12” tile should have a minimum 24” wide membrane).
CuringKeep all traffic off the installation until material cures (6-12 hours approx.). Temperature and humidity can affect working time and setting time.
Expansion and Control JointsFollow ANSI specification A108.01 “Requires for Movement Joints”; Provide for expansion and control joints as specified per TCNA Detail EJ171 or TTMAC Specification Guide 09 30 00 Detail 301EJ. Do not cover any expansion joints with mortar.
StorageStore it in a cool dry area.
ProtectionClean your hands after use it, avoid eye contact, or prolonged contact with skin, if eye contact occurs, flush with water for 15 minutes and consult a physician immediately.Keep out of reach of children.
www.crest.com.mx [email protected]
Ÿ Do not use over dimensionally unstable substrates such as hardwood flooring, oriented strand board (OSB), substrates containing asbestos, or metal. See “Suitable Substrates” section above.
Ÿ Do not use on plywood in exterior/wet applications or in heavy traffic areas.
Ÿ Do not bond directly to hardwood, Luan plywood, cushion or sponge-back vinyl flooring, metal, fiberglass, particle board parquet.
Premium Tile & Stone Installation Products
www.crest.com.mx
IMPORTANT Technical Data
We are not responsible for any loss or damage caused due to the application of this product. Prior to application, the user must confirm whether the product is suitable for your intended use. The user must assume responsibility for the risks or damages arising from an application other than specified.
Standards and ApprovalsŸ American National Standards Institute (ANSI) - ANSI
A118.10 of the American National Standards for the Installation of Ceramic Tile.
Ÿ Tile Council of North America (TCNA) - TCNA Handbook for Ceramic Tile Installation, TCNA Method EJ171.
Ÿ ASTM D9068
Summary Technical Chart:
Available:
Packaging:
Coverage:
Shelf Life:
Open Time
Installation Temperature:
Hardness:
Average Shear Strength:
Elongation:
Cure Time:
Impact Insulation Class IIC:
Sound Transmition Class STC:
Flash Ponint:
*Values might vary depending on the tile size, leveling the substrate, conditions and method of installation.
White
5 Gal. Pail (19.1L),
50 sq. ft / gall
12 months in a cool dry area, in original packing and unopened.
15 Minutes
Between 50/100°F (10/38°C)
45 Shore A Type
180 PSI (12.65 Kg/cm²)
600%
6-9 hours
70 dB
74 dB
145°
Test Method Requirements Requirements
4.1 Fungus Micro Organism
4.2 Seam Strength
4.3 Break Strength
4.4 Dimension Stability
4.5 ASTM D9068 Waterproofness
*Note: Average values obtained at 73°F ± 4°F and relative humidity of 50 ± 5%. Performances vary depending on the format and size of the trowel to use as the leveling of the substrate.
Resisit
8 lbs/ In
170 psi
Pass
>8 lb
195 psi
Pass
Pass
ANSI SpecificationA118.10 – Bonded waterproof membrane below thin set, tile and dimension stone installation.
Premium Tile & Stone Installation Products
Technical InformationFor technical support and assistance, please visit our website at www.crest.com.mx For questions or comments contact [email protected]
Last modification January 2016
Crest Membrana 3010®Waterproofing, Crack & Sound Isolation Membrane Urethane based meet and exceeds ANSI A118.10For walls and floors, vertical and horizontal applications*Monterrey and Mexico plants Certified.
