Precision Calibration Solutions · These kits are used to make error-corrected measurements of...

TECHNICAL DATA 2Z-058C2900 Inland Empire Blvd. • Ontario, California 91764 • USA

2.92mm CAL KITSFrom

Maury Microwave is ISO: 9001:2008/AS9100C Certified.

Contact Us:Web: maurymw.com

Email: [email protected]

Voice: +1-909-987-4715

Fax: +1-909-987-1112

Models:8770E47 – Sliding Termination Kit

8770F47 – Fixed Termination Kit

Precision Calibration Solutions

Precision VNA Calibration Kits – 2.92mm

MAURY MICROWAVE CORPORATION 2 TECHNICAL DATA 2Z-058C

8770E47/F47 2.92mm Calibration KitsMaury 8770E47/F47 precision 2.92mm calibration kits are specifically designed for use with the Agilent PNA series of vector network analyzers. These kits are used to make error-corrected measurements of 2.92mm devices in frequencies ranging from DC to 40 GHz. Each kit is supplied with a full set of calibration standards (listed on page 3); including shorts, opens, sliding and/or fixed loads, calibration constants on a USB flash drive, a torque wrench and two double-end wrenches, plus a set of Maury precision NMD2.4mm test port adapters and 2.92mm in-series adapters.

2.92mm Connector DescriptionPrecision 2 .92mm connectors are miniature, instrument grade, air-interface connectors that operate mode free up to 40 GHz, and comply with the IEEE standard 287 general precision connector, instrument grade. For detailed interface specifications please refer to maury data sheet 5E-063.

NMD2.4mm Connector DescriptionPrecision NMD2 .4mm connectors are ruggedized test port connectors used for stable connection to network analyzers. The female connector is only mateable to NMD male connectors via the external threads on the male nut . For detailed interface specifications please refer to Maury data sheet 5E-082.

These kits are configured for use in performing one-port SOL (Short-Open-Load) response calibrations (a method used for measuring VSWR/Return Loss), and a full two-port SOLT (short-Open-Load-Thru) calibrations (for performing forward and reverse transmission and reflections measurement).

The Importance of VNA CalibrationAny uncalibrated test setup will exhibit three types of measurement errors; systematic, random and drift. The systematic errors are inherent in the cables, connectors, adapters and test equipment used. The individual and cumulative effects of these errors has a negative impact on the ability to obtain accurate measurement from a device under test (DUT). Accuracy ultimately depends on how well these errors are corrected. The basis of test setup error correction is the measurement of known electrical standards, such as a thru, open, short, and precision load, to find deviation from a mathematically calculate set of calibration constants. By calibrating your PNA with these standards, you can compensate for the inherent systematic errors in your test setup, and can have full confidence in your test and measurement data. Maury Calibration Kits are designed to give you that confidence.

2.92mm VNA Calibration Kits from Maury Microwave8770E47 Sliding Termination Kit and 8770F47 Fixed Termination KitFeaturesu NMD2.4mm and NMD2.92mm Adapters

u Phase Matched In-Series Adapters

u DC to 40 GHz

u Designed for Optimum Compatibility with Keysight PNA series Test Sets

Calibration Methods Supportedu 8770E47 – Sliding/Fixed Load SOLT (DC–40 GHz)

u 8770F47 – Fixed Load SOLT (DC–40 GHz)


MAURY MICROWAVE CORPORATION 3 TECHNICAL DATA 2Z-058C

Components Included in 8770E47 KitsQTY DESCRIPTION MODEL

1 2.92mm female fixed short 8771F2

1 2.92mm male fixed short 8772F2

1 2.92mm female open 8773A2

1 2.92mm male open 8773B2

1 2.92mm female fixed termination 8775A3

1 2.92mm male fixed termination 8775B3

1 2.92mm female sliding termination 8777A2

1 2.92mm male sliding termination 8777B2

1 NMD2.4mm female to 2.92mm female adapter 7909F1

1 NMD2.4mm female to 2.92mm male adapter 7909F2

1 2.92mm female to 2.92mm female adapter 8714A2

1 2.92mm male to 2.92mm male adapter 8714B2

1 2.92mm female to 2.92mm male adapter 8714C2

1 5/16-inch torque wrench (8 in/lbs) 8799A1

1 Sliding termination pin depth adjustment tool 8777S02

1 5/16-inch double end wrench —


1 PNA calibration constants on USB flashdrive —

1 Operating instructions (manual) —

1 Instrument case —

8770E47

8770F47

Components Included in 8770F47 Kits

QTY DESCRIPTION MODEL

1 2.92mm female fixed short 8771F2

1 2.92mm male fixed short 8772F2

1 2.92mm female open 8773A2

1 2.92mm male open 8773B2

1 2.92mm female fixed termination 8775A3

1 2.92mm male fixed termination 8775B3

1 NMD2.4mm female to 2.92mm female adapter 7909F1

1 NMD2.4mm female to 2.92mm male adapter 7909F2

1 2.92mm female to 2.92mm female adapter 8714A2

1 2.92mm male to 2.92mm male adapter 8714B2

1 2.92mm female to 2.92mm male adapter 8714C2



1 PNA calibration constants on USB flash drive —

1 Operating instructions (manual) —

1 Instrument case —

MAURY MICROWAVE CORPORATION 4 TECHNICAL DATA 2Z-058C© 2015 Maury Microwave Corporation. All Rights Reserved. Specifications, kit configurations and constituent components are subject to change without notice.


COMPONENT SPECIFICATIONS

Fixed Shorts – Models 8771F2 & 8772F2

Frequency Range . . . . . . . . . . . . . . . . . . . . . . DC to 40 .0 GHz

Minimum Reflection Coefficient . . . . . . . . . . . . . . . . . . . 0 .98

Phase Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . ±2 degrees

Nominal Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . 50 ohm

Opens – Models 8773A2 & 8773B2Frequency Range . . . . . . . . . . . . . . . . . . . . . . DC to 40 .0 GHz

Minimum Reflection Coefficient . . . . . . . . . . . . . . . . . . . 0 .98

Phase Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . ±1 .5 degrees


Fixed Terminations – Models 8775A3 & 8775B3

Frequency Range . . . . . . . . . . . . . . . . . . . . . DC to 40 .0 GHz

Maximum VSWR: DC to 4 .0 GHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 .016 4 .0 to 40 .0 GHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 .12

Power Handling . . . . . . . . . . . . . . 0 .5 watt CW, 0 .5 kW peak

Nominal Impedance . . . . . . . . . . . . . . . . . . . . . . . . . 50 ohm

Sliding Terminations – Models 8777A2 2.92mmfemale & 8777B2 2.92mm male

Frequency Range . . . . . . . . . . . . . . . . . . . . . . 4 .0 to 40 .0 GHz

Air Line Accuracy . . . . . . . . . . . . 46 dB min, 4 .0 to 40 .0 GHz(equivalent return loss of air line impedance)

Maximum VSWR of Terminating Element: 4 .0 to 10 .0 GHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 .10 10 .0 to 40 .0 GHz . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 .05


Power Handling . . . . . . . . . . . . . 0 .5 watts CW, 0 .5 kW peak

Travel . . . . . . . . . . . Greater than 1/2 wavelength at 4 .0 GHz

RECOMMENDED ACCESSORIES

8770E47 & 8770F47 KitsA050A Digital Connector Gage Kit (Thread-on Type)The A050A Digital Connector Gage Kit includes one each A050A female and male gages; corresponding female and male master gage blocks; one 8799A1 5/16-inch torque wrench (pre-set to 8 in/lbs) and one 5/16-inch double-end wrench. These components are housed in their own wood instrument case, as shown in the photo at right .

A050A

ADAPTERS SPECIFICATIONS

NMD Test Port Adapters – Models 87909F1 & 7909F2


Maximum VSWR: DC to 20 .0 GHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 .10 20 to 40 .0 GHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 .16

Insertion Length . . . . . . . . . . . . . . . . 1.291 inches (3.279cm)


Connectors: 7909F1 . . . . . . . . NMD2.4mm female to 2.92mm female 7909F2 . . . . . . . . . NMD2.4mm female to 2.92mm male

In-Series Adapters – Models 8714A2/B2/C2


Maximum VSWR: DC to 4 .0 GHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 .05 4 .0 to 20 .0 GHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 .08 20 .0 to 40 .0 GHz . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 .12

Insertion Length . . . . . . . . . . . . . . . . . . 0.65 inches (1.65cm)


Connectors: 8714A2 . . . . . . . . . . . 2.92mm female to 2.92mm female 8714B2 . . . . . . . . . . . . . . 2 .92mm male to 2 .92mm male 8714C2 . . . . . . . . . . . . 2.92mm female to 2.92mm male

Precision Calibration Solutions · These kits are used to make error-corrected measurements of...

Documents

Transcript of Precision Calibration Solutions · These kits are used to make error-corrected measurements of...